Search Documents

By J. C. Franklin

A data-acquisition system was designed by the Bureau of Mines to monitor five detectors with radon continuously flowing through each. These detectors could be monitored up to 12 times an hour, but were only monitored according to a preset time, thus allowing radon to be monitored continuously in a uranium mine. The counter can be set to monitor each detector for any period of time up to 16.5 minutes. This allows very low concentrations to be monitored longer to reduce statistical error. There would be no upper limit in radon concentration that could be monitored, but there would be a lower limit of 50 picocuries per liter (pCi/l). Each detector was cylibrated in the laboratory by the Lucas flask method. Multiple samples were taken at two different concentrations, and the correction factor for each detector was determined by a least squares fit of the data. To verify the calibrations, a series of measurements at several concentrations were made against a constant source. Our agreement at low radon concentrations (300 pCi/i) with the two-filter method as within 3 percent; thus, the total error would be this difference plus the two-filter error. At high concentrations the coefficient of variation ranged between 2.1 and 9.8 percent for the five different detector units.

Jan 1, 1976

By C. H. Titus

This study consists of four descriptive Sections covering respectively: a state-of-the-art literature survey on ungrounded and grounded power systems, a report on literature pertaining to human threshold limits of electric shock, an analysis of the performance requirements of isolated systems and a section on design and performance specifications for an isolated system the final section includes copies, and translations where applicable, of the most important articles on foreign mining practice as well as some technical publications which could be difficult to obtain elsewhere. Section 2 - Literature Survey In analyzing the available literature on ungrounded systems it became apparent that too strict an interpretation of Section 1.1 of the Contract would limit the survey in both period of time analyzed and in available literature which discussed several types of power systems. Therefore, the survey was expanded to cover approximately the past twenty-year period and to cover literature which addressed itself to both ungrounded and grounded power system operation. Section 2 gives a brief summary of this literature survey and lists the important papers and books which were examined.

Jan 1, 1972

By Thomas Hans Kleine

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995

By A. M. Tunstall

Aspects of blast vibrations, damage mechanisms and the influence of rock quality on damage severity are reviewed and results presented from a monitoring programme in which the rock mass rating for six tunnels was determined. The peak particle velocity induced in the tunnels during open-pit blasting was measured and the tunnels were inspected visually for fresh damage after each blast. The results suggest that the quality of rock in which an excavation is situated has an influence on the level of ground vibration to which it can be subjected without sustaining damage. This means that the use of a single limiting value of peak particle velocity, as in the blast damage criteria for residential structures, is not ideal and may result in damage to excavations in poorer-quality rock masses

Jun 19, 1905

By R. K. Rath

Adsorption, electrokinetic and flotation studies were carried out. The maximum density of adsorption of guar gum was obtained at pH 7.5 on sphalerite and at pH 11.5 on galena. Flotation recovery of sphalerite was reduced only marginally by the presence of guar gum in the pH range investigated, whereas recovery of galena was reduced to about 20% at pH 12. Differential flotation tests on binary mixtures indicated that 10 ppm of guar gum can depress galena and separate it from sphalerite at around pH 12.1. Co-precipitation tests confirmed the formation of a metal ion-guar gum complex in the bulk solution, suggesting that this is the precursor to adsorption. The adsorption isotherms for both minerals followed Langmuirian behaviour, but adsorption of guar gum on galena was significantly higher than on sphalerite and dissolution tests indicated that the concentration of Pb ions released from galena was an order of magnitude greater than that of Zn ions dissolved from sphalerite

Jun 21, 1905

By Mohamed Yusuff

Modern transportation systems are one of the most important achievements of our civilization and provide us with tools for broadening individual and social freedom of choice. The transportation system initiated today is handed dawn to the next generation, probably with little choice because of the enormous expenditure of monies involved, and influence their way of life as to where they should live and where they should work. The ever increasing antagonism between the citizens and the planners of the transportation systems necessitates a careful review of the entire planning process. The planning process can be broadly classified into: the goal formulation and decision making process; the plan development process; and the plan implementation process. THE GOAL FORMULATION AND DECISION MAKING PROCESS Goal formulation and decision making is one of the vital phases of the planning process and is primarily based upon social values. In measuring social values, the planner must employ an appropriate scale of measurement since in the absence of this yardstick, these values tend to became vague and abstract ideals. The need for major social programs and concerns (poverty, etc.) of the urban areas should be analyzed to determine the type of transportation system which would contribute to the solution.

Jan 1, 1974

By V. Bondarenko

The forecasting of floating earth inrush into the working is to a great extent connected with the investigation of the rock mass stressed-deformed state around the working. The aim of such investigations is to estimate the carrier ability of the protective layer (which is stabilized by the physico-chemical mode of fixing) and to determine it's thickness, which is to be sufficient to present the floating earth inrush into the working. We consider the protective layer to have exhausted it's carrier ability if the rocks of this layer reached the overlimit phase of deformation and it's greater part (section), which adjoins the working. is destroyed up to the limit of the remaining strength. So, the aim of investigations is to determine the size of the rocks inelastic deformation zone in the roof of the working. It is necessary to take into account the presence of water saturated seam in the roof and the overlimit characteristics of the rocks, their ability to lower the carrier capacity up to the level of the remaining strength.

Jan 1, 1996

By Hamid Mahmoudabadi

In the present paper, the performance of four approaches based on neural networks and geostatistical method for grade estimation are compared and analyzed their performance to find a proper method. Four methods, Multi Layer Perceptron neural network (MLP), Radial Basis Function (RBF), General Regression Neural Network (GRNN) and Ordinary Kriging (OK) are selected for ore grade estimation of variable Fe in an iron deposit located in Iran. For each method, two diagnostic statistics are calculated: Mean square error (MSE) and correlation coefficient. The results show the superiority of the General Regression Neural Network.

Oct 1, 2009

By Seung-hoon Lee

The use of piled raft foundations has been considered as an economical alternative to conventional piled foundations because a portion of the applied load is carried by the raft in the design of piled raft foundation. In analyzing the behavior of a piled raft foundation as a settlement reducer, an accurate estimate of settlements of the system should be made on the basis of the understanding of nonlinear behavior of piles in layered soils as well as the interaction between the raft, soils, and piles. Although the 3-dimensional finite element method and simplified analysis methods have been used for the design of piled raft foundations, these methods were found to be inadequate for the practical purpose or could not consider the interactions properly. This study developed an approximate hybrid method of analysis to be used for the practical design of piled raft foundations considering pile-soil, raft-soil, pile-soil-pile and raft-soil-pile interactions. In the presented method of analysis, the settlements of the system are estimated satisfying the compatibility of two separate models which are the flexible raft model consisting of 2-dimensional finite elements supported by springs representing soils and piles, and the group-pile model embedded in layers of soil having different properties. Comparisons with other analytical methods as well as a 3-dimensional FEM program were made to verify the sufficient capabilities of the proposed hybrid model for application to practical design and analysis of piled raft foundations.

Jan 1, 2008

By Robert D. Perry

This report describes methods of reclaiming abandoned or inactive tailings ponds and dams. The investigated sites were selected tailings deposits adjacent to metal mines in the southwestern United States and the Pacific Northwest. The basic data developed for each site consisted of the following: a review of existing literature: a site visit that included sampling of the tailings and surrounding materials; laboratory and engineering studies; and development of reclamation plans. Laboratory tests determined the gold and silver content of each tailings deposit and the chemistry of the tailings and surrounding materials. Reclamation plans that include approximate costs were developed for five tailings deposit sites. These ranged in size from 52,000 to 103,000,000 tons. Our conclusions on the remining potential of each site are based on the tailings assay and other technical data. This study concludes that remining as a reclamation tool is feasible at certain sites. Included in this report is a remining program as part of the overall reclamation plan for two sites. Our preliminary results indicate that remining as a reclamation tool is feasible for only one of them.

Jan 1, 1981

By Emad W. Shublaq

Contractual site plans are implemented for executing pile foundations (5 x 5) at segmental concrete bridge. Project schedule demands have forced the contractor to find out the most economical procedure in achieving the goal. This paper presents a site management technique which is applied by the Contractor. This was found to be fruitful and as much as 60% saving was gained.

Jan 1, 1992

Correlation of Air Recovery with Thin Film and Froth Stability in Flotation

Sep 13, 2010

By John F. Beesley

INTRODUCTION This paper discusses the design of the subsurface nuclear waste repository at Yucca Mountain, Nevada; and possible concepts for construction of the subsurface facility. Subsurface construction at Yucca Mountain is planned to last for 20 or more years, and may be accomplished using tunnel boring machines (TBM), drill and blast methods, raise bore machines, and roadheaders. The design of the subsurface facility includes approximately 107 km (66 miles) of tunnels and drifts. The vast majority of the repository will be excavated with TBMs. Design and construction concepts for the subsurface repository discussed in this paper are based on the License Application that was submitted to the U.S. Nuclear Regulatory Commission (NRC) by the U.S. Department of Energy (DOE) on June 3, 2008. The License Application was subsequently docketed by the NRC in September 2008. When a Construction Authorization is received from the NRC, notices to proceed with subsurface construction at Yucca Mountain will be issued by DOE. The Yucca Mountain site is located in the Mojave Desert approximately 150 km (90 miles) northwest of Las Vegas, Nevada. The site is on federal land in southern Nevada and is shown in Figure 1. Yucca Mountain is a ridge of volcanic rocks com-posed primarily of solidified volcanic ash. Previous underground construction work at Yucca Mountain included excavation of two tunnels using two different TBMs. The first tunnel, the Exploratory Studies Facility (ESF), is a 7.62 m (25 ft) diameter tunnel that is 7,877 m (25,843 ft) long and was described by Morris and Hansmire at the Rapid Excavation and Tunneling Conference (RETC) in 1995. The second tunnel, known as the Enhanced Characterization of the Repository Block (ECRB), was a TBM drive of 5.0 m (16 ft, 5 in.) in diameter and 2,681 m (8,796 ft) long. The second tunnel was excavated in 1998 and was described by Fulcher, Eastlund and Copeland at RETC 1999 and is named the East?West Cross Drift in that paper. (These previously excavated tunnels are shown in Figure 2.) In the volcanic rock formation where the vast majority of the planned repository will be con-structed, previous tunneling conditions were generally very good.

By O. Matwijenko

"1. IntroductionThe Falconbridge Owl Creek open pit gold mine is located 17 km northeast of Timmins and 2.5 km west of the Kidd Creek metallurgical site. Diamond drilling first commenced in 1964 with open pit production commencing in 1982. Other operations within close proximity are the Canamax-Pamour Bell Creek Mine and the Falconbridge Hoyle Pond Mine.Since 1982, 1,216,000 tonnes assaying 4.5 g/t have been processed in six concentrators. This paper summarizes the metallurgy achieved with special emphasis on some of the unique problems encountered in the processing of this refractory ore.2. GeologyThe Owl Creek deposit, located 3 km north of the Porcupine-Destor fault is in easterly trending carbonaceously altered volcanic and sedimentary rocks. The deposit strikes east and dips steeply north.The ore body can be best described as a wedge shaped sandwich of volcanic basalt between the surrounding sedimentary greywacke. The north and south volcanic-sedimentary interfaces are marked by graphitic zones. The south graphitic contact is more continuous with its thickness varying from 5 m to 20 m as compared to 0.5 m to 3 m to the north. Quartz veins occur throughout the deposit with a predominant vein running along the south contact where it is characterized by numerous graphitic inclusions. Some veins carrying gold values intrude into the sediments in the north. With depth the sedimentary and volcanic zones taper while the quartz-graphitic zones appear to become more dominant."

Jan 1, 1988

By Dan Brown

This paper presents a case study of a cyclic lateral pile load testing program performed on two 18-in square prestressed concrete piles (PSC) in Savannah, Georgia. The load test program was developed to simulate the lateral behavior of a single pile under seismic loading conditions for the design and construction of a large LNG storage tank. The lateral load tests included cyclic loading to measure possible degradation in soil response followed by static loading to large displacements (around 6 inches at the loading point). The lateral load was applied through a reciprocating jack positioned to push and pull the piles against each other. The test piles were instrumented with multiple displacement transducers, downhole inclinometer, and strain gauges. This paper provides an interpretation of the test results regarding the pile performance and soil response to monotonic and cyclic lateral loading. A backfitted computational model of the soil resistance was developed to match the test results using the LPILE computer program. The load-deflection and deflection/moment versus depth comparisons suggest that this model appears to capture the behavior relatively well within the general range of suitability for design purposes. New design curves were developed based on the soil parameters derived from the lateral load test results.

Jan 1, 2003

By R. E. Robinson

A novel variation of the GYPCIX process for the treatment of the acid mine effluent water from Grootvlei is described, in which a number of valuable by products can be obtained and the product water can be used for a variety of different purposes. A conceptual case study is presented in which the important cost parameters are described and certain critical path activities are indicated in order to derive a Return on Investment evaluation according to methods previously published. The study indicates that the treatment costs can be dramatically reduced, provided that proper utilization of the by products is taken into account. There are many possible uses for the water. However, by far the most advantageous contribution to the RDP and the best return on capital is derived if the water is used to establish small-lot farming activities providing work opportunities for thousands of people and contributing several hundred million Rands to the GDP. Vastly improved social conditions will be generated in an area of Gauteng that is in danger of rapid deterioration and a contribution will be made to maintaining mining activities in this area. The environmental impact is positive.

Jan 1, 1998

By R. L. Andrew

The southwest Pacific has produced at least four of the world’s premier porphyry copper-gold deposits, and the current level of exploration is likely to produce even more. An appreciable amount of gold is being produced with this copper, with obvious economic advantages. Gold content, in addition to their large size, makes the southwest Pacific’s porphyrycopper-gold deposits very attractive exploration targets. The recognition of telescoping and overprinting of porphyry systems has produced a greater awareness of the likely surface expressions, in particular the significance of advanced argillic lithocaps in porphyry exploration. The recognition of the spatial and genetic association of porphyry copper and epithermal gold systems (Sillitoe, 1972), as in other parts of the world, has had important implications for exploration in the Asia Pacific region.

Jan 1, 1995

By A. Vorster

The objective with mine planning is to consistently deliver production conforming to quality and quantity requirements throughout the life of the mine. The complexity of the operational context of the modern mine extends far beyond the actual production actions and there is a need to find ways of analysing and managing this extended environment. A well-established approach to handling complex situations rely on the creation of representative models that use classification and visualization strategies. An example of the use of a classification scheme is the periodic table of the elements. All physical matter can be expressed as combinations of basic elements. Not only is the periodic table useful in classifying and identifying matter but it can also be used for the prediction of the properties of unknown matter and compositions of elements.

Jan 1, 2001

By Walter Ensinger

Special foundation works is one of the most innovative sectors in civil engineering and construction. Both engineering techniques and construction machinery are undergoing continu­ous further development. These developments are providing ways to meeting the world-wide requirement for special geotechnical works even faster, even better and more efficiently. Unfortunately, accident prevention organisations have had to realise that the figures on in­dustrial accidents in special foundation works are still above average in number. The Safety & Environmental Working Group of the EFFC thereupon started to carry out a survey on acci­dents occurring in this sector and used this information as a basis for the preparation of acci­dent statistics and an accident analysis. The objective of this undertaking is to determine key accident occurrences and their causes and to consequently determine measures for improved health and industrial safety.

Jan 1, 2002

By H. Saroglou

The anisotropic behaviour of Athens Schist has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the Athens Schist were statistically analysed and evaluated.

Jan 1, 2004