Search Documents

By Otto Sandovel Zea

El compromiso de minería perfecta se limita no solo a la preservación del medio ambiente, sino a la prevención de riesgos por desprendimiento de rocas y aplastamiento en el interior de la mina. En ese sentido, el presente texto señala la factibilidad de minar a sección plena todos los tajeos a través de la simulación de las condiciones más favorables y desfavorables de la mina, determinando como la alternativa más viable la bóveda en arco. Dicha estructura otorga estabilidad a las labores de minado -en tanto da sostenimiento activo a través del (Shotcrete SFR y Pernos Hydrabolt), así como desarrolla mayor productividad y menores niveles de riesgo por desprendimiento de rocas, menores grados de sobre excavación y genera de vibraciones al haber implementado la voladura de Pre-corte en sus labores.

Sep 12, 2011

By Andrew G. Martin

In 1991, Modular Mining Systems began marketing a Slope Monitoring System (SMS) now installed at twelve mines. The SMS uses automated wire line extensometers to monitor field conditions frequently. Every few minutes, the slope displacement values and current temperature are transmitted to a central computer via a packet radio telemetry system. The desktop workstation receiving the data continuously provides updated displays of active slope monitors and generates audible and visual alarms if movement exceeds user specified thresholds. The computer system also generates numerous graphs and reports for quick analysis of slope stability. This work describes the functionality of the SMS, details improvements to the SMS hardware and software developed for several clients, outlines different installation techniques needed for wall rock and spoil monitoring, and interprets slope movement data using illustrations of stable and unstable conditions.

Jan 1, 1996

By Alfred V. C. Meyer

A Blastcorder4 was calibrated on the Bureau of Mines shaking table in the frequency range of 12 to 40 c.p.s. and in the amplitude range' of 0.25 to 1.0 g. The results of this calibration study show that in the frequency range of 12 to 30 c.p.s. the average accuracy of the Blastcorder is approximately ± 0.1 g.

Jan 1, 1962

By Bradford F. Townsend

A study was made on six collapses that occurred during large-diameter tunnelling through weak sedimentary rocks and soil using SES methods in three stages?top heading, bench and invert. The collapsed lengths are between 20 m and 277 m. The collapses were re-mined using essentially the same tunnel-ling method with larger excavation profiles to accommodate the designed remedial measures consisting of ground treatment, pre-support and stronger initial support/outer lining required to carry higher ground loads acting in the collapsed lengths. The paper presents information on the collapses and the design and execution of the remedial measures.

Jan 1, 2008

By D. Brün, T. W. Nattkemper, T. Kuhn, T. Schoening

Underwater exploration for marine resources using camera-equipped devices (OFOS, ROV, AUV) is receiving growing attention. This development is creating a continuously growing pile of digital underwater images leading to a serious bottleneck in the analysis. However, any harvesting strategy must be coupled to an efficient and effective assessment of the biodiversity in the area of interest and in nearby control areas. To integrate manual image and computational image interpretation on different levels (i.e. regarding geology and environmental sciences and taxonomy), sophisticated software support is required, which is not yet offered explicitly, neither by commercial software companies nor by academic or other publicly founded institutions. Here, we present the first version of a new digital asset management system that offers functionalities for easy data management, sharing, manual annotation and integration of computational modules for image enhancement/pre-processing and interpretation. The functionality is demonstrated with data from the CCZ provided by the BGR Hannover.

Sep 1, 2014

This paper sets out to examine the possible relationships between three factors, they are, the rate of growth of world production of minerals, the growth of Australian production and the growth of scientific and engineering knowledge.The first two are quantified, in terms of tonnes and value. The third, an abstract concept "knowledge", requires to be quantified, in terms of manpower.A mathematical model, which has general application, was derived to demonstrate certain axiomatic premises and to define, more precisely, basic concepts related to the philosophy of knowledge.Finally a summary is made of education-cum-industry issues.

Jan 1, 1981

By Harry C. Verakis

A conveyor belt fire presents a serious safety hazard in an underground coal mine. A review of underground coal mine fires involving conveyor belts which occurred within the past two decades was made by the Mine Safety and Health Administration (MSHA). Belt fires that occurred during this period of time have burned as much as 610 m of belting before the fire was extinguished. In an effort to improve safety, MSHA has undertaken a program to study the flammability of conveyor belts in large and small-scale tests. Large-scale tests were conducted on various types of mine conveyor belts using a range of airflows from 0 to 6.1 m/s. Data were obtained to evaluate the effect of airflow on flame spread and other combustion properties of the conveyor belts. The results from the large-scale tests were utilized to develop a new MSHA laboratory-scale test for evaluating the flame resistance of conveyor belts used in underground coal mines. Agreement of results based on a pass/fail criterion was obtained between the large-scale test and new laboratory-scale test. A summary of test results from the new test is shown for different conveyor belt formulations. MSHA also performed a series of fire tests with wood samples using the new laboratory-scale tunnel apparatus. These tests were conducted at airflows from 0.5 to 5.1 m/s to determine the effect on flame spread and burn damage. The data were also analyzed to determine if wood could be used as a calibration standard. The results indicate the flame spread behavior of the wood follows trends similar to results obtained with conveyor belts. The data did not show the precision needed to use wood as a calibration standard. MSHA intends through rulemaking procedures to replace the "20g" conveyor belt acceptance test with the new laboratory-scale test. MSHA also plans to implement a voluntary acceptance program. Under this program, a. conveyor belt manufacturer could obtain an MSHA acceptance for belts meeting the new test criterion. A belt accepted under the voluntary program could then be used underground. Use of conveyor belts meeting the new test would limit the propagation of fire and reduce the probability of igniting other combustibles in the belt entry.

Jan 1, 1991

By Robert A. Field

Static-Load Piledriving utilizes a hydraulic push to facilitate the installation of a pile. The pile is not rotated, impacted or vibrated. A smooth pushing force advances the pile incrementally into the ground. Static-Load devices must have a reaction mass to push against. The most simple form of a Static-Load device is a jack; more advanced equipment, such as the Still Worker, also utilizes this approach. This paper focuses on the use of the Still Worker on three challenging projects. In each case, the existing site conditions made it risky, or unattractive, to utilize conventional impact, vibratory, or drilled-shaft equipment.

Jan 1, 1997

The aim of this investigation was to study the influence that varying production rates have on iron sinter quality. This was done by performing sinter pot tests at different pressure drops over the sinter bed, namely 11 kPa and 15 kPa (for 500 mm total bed depths). During each of the sintering processes temperature-time profiles were recorded of the top, middle and bottom layers of the sinter bed. On completion of the sinter process the sinter cakes were divided into top, middle and bottom layers. The physical properties of each layer were subsequently characterized by performing a tumbler test and a sieve analysis. A comprehensive mineralogical study was also conducted on each layer. This study revealed that sinters of similar cold strength could be produced under the examined production rates. However, a higher production rate was accompanied by an increased amount of fines. The cold strengths of both sinters significantly increased from the top layer to the bottom layer of the sinter bed. This strength variation is not related in any simple way to the phase composition. Keywords: Sinter, sinter bed, production rate, phase composition, cold strength, tumbler index, sieve analysis, temperature-time profile

Jan 1, 2003

By Steve Kral

For a state whose roots are in mining, most Colorado residents probably do not realize that the industry still contributes heavily to the state’s economy. In 2005, the industry contributed, directly and indirectly, about $8 billion to the state’s economy, according to the Colorado Mining Association (CMA). It employed nearly 10,000 people at mines and support businesses. And the mining industry in Colorado is one of the highest paying occupations in the state, averaging about $80,000 a year in wages and benefits. The state’s coal mining industry produced nearly 36 Mt (40 million st) of coal in 2005, valued at $800 million, the CMA said. That was seventh in the nation. And Colorado’s only major gold mine produced 10.2 t (329,000 oz) last year, valued at $124 million. That was third in the nation. And Phelps Dodge’s Henderson Mine produced about 12.7 kt (28 million lbs) of molybdenum, valued at $350 million. Colorado is the largest molybdenum producing state in the nation.

Jan 1, 2006

By F. E. Chase

Mobile roof supports are shield-type support units mounted on crawler tracks. Mobile roof support (MRS) units are used during retreat mining, and they eliminate the setting of roadway, turn, and crosscut breaker posts which are required during pillar recovery operations. Mobiles are a more effective ground support than timbers, and their usage enhance the safety of section personnel and reduces material handling injuries. MRS usage is rapidly increasing, and approximately 40 U.S. coal mines have successfully employed this relatively new technology. This paper is in response to increasing requests from operators, State and Federal Regulatory Agencies, and others on the practical aspects of MRS usage in underground coal mines. During this investigation, nearly half of the U.S. mines which have utilized mobiles were visited. This report depicts the more common pillar extraction methods which operators have found successful. The Christmas tree and outside lift methods are illustrated and discussed. Roof control plans that do not require breaker posts or allow pillar extraction with fewer than four mobiles are also examined. In addition, operators' experiences with setting pressures, loads, and rates of loading during pillar extraction are addressed. Mining and support strategies to more effectively control hillseams, weak roof, and gob overrides which have entrapped equipment are also discussed.

Jan 1, 1996

By Claus Goetzel

THE object of this investigation was to determine whether silver alloys could be used instead of the currently employed insert of high-expansion AVERAGE COEFFICIENT PER DE G. C. OVEN RANGE 20° To 200° C. Pure aluminum '31.6 X 10-6 Cast low-expansion Si-Cu-Ni-Al piston alloy 20.0 X 10-6 High-expansion austenitic Cu-Ni cast iron 19.3 X 10-6 Cast steel (0.25-0.35 C, 0.10-1.0 Mn) 12.6 X 10-6 Cast iron (3.15 total C, 2.16 Si) 12.8 X 10-6 Pure silver 18.9 X 10-6 austenitic ferronickel alloy, to reduce the wear of ring grooves in light metal pistons. A typical example of a piston containing a ferronickel insert is shown in Fig. 1. The high coefficient of expansion of silver made it worthy of consideration, while the small size of the insert would render it use feasible in Germany as an emergency in is- tire. The coefficients of linear expansion of several metals and alloys are as shown in the table above. Obviously the melting point of the insert must be high enough to prevent it from melting when the light alloy is cast around it. This imposes a lower limit of about 850° C. for the solidus of the silver alloy. Pure silver melts at about 961° C., so that the Fin. 1.-PISTON CONTAINING tolerable depression in the solidus is rather FERRONICKEL INSERT. small. To avoid deformation of the insert during use a Brinell hardness number of at least 60 appears necessary.

Jan 1, 1937

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to 5-ton pieces, a 150-ton batch-type retort was designed and constructed at the Bureau of Mines Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11 ½ feet inside diameter, and is supported in a 95-foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, was used as the test shale. To date, 11 runs have been completed, and the results of the last 10 of these are reported. The effects of oxygen content of the retorting gas and the superficial gas velocity of the retorting gas on oil recovery from a column of mine-run oil shale were studied. In one run, the average particle size of the shale was substantially increased to determine its effect on oil yield. Oil recoveries ranged from a low of 39.3 to a high of 65.8 volume-percent of Fischer assay.

Jan 1, 1974

By Christopher Mark

The Bureau of Mines has recently completed a comprehensive study of coal strength. More than 4000 individual test results from over 60 seams were extracted from the literature and combined in the most complete data base of the uniaxial compressive strength of coal ever assembled. In addition, more than 100 case studies of in-mine pillar performance were available in the Analysis of Retreat Mining Pillar Stability (ARMPS) data base. Statistical analysis of this wealth of data has yielded valuable results. The data shows clearly that the "size effect" is related to coal structure. The widely-used Gaddy formula, which predicts a significant strength reduction as the specimen size is increased, was found to apply only to "blocky" coals. For friable coals, the size effect was much less pronounced or even non-existent. Case histories of failed pillars are the best available data on in situ coal strength. This study found no correlation between the ARMPS stability factor of failed pillars and coal specimen strength. Pillar design was much more reliable when a uniform coal strength was used in all case histories.

Jan 1, 1996

Jan 1, 1968

By K. Pathak

Loaders and dump trucks are the most commonly used surface-mining equipment. Negligence of the safety-engineering aspects of dump trucks may result in serious accidents in a mine. A reduction in the risk of an accident due to the deployment of trucks can he achieved by engineering analysis, risks assessment, improved safety features, active safety devices, condition-based maintenance, in-built protection systems, etc. This paper presents some cases of accidents in Indian surface coal mines and advocates a systems approach to safety.

Jan 1, 1999

By James Anstey

BHP Billiton?s Cannington facility is a mining and minerals processing plant near Mt. Isa in Central Queensland, Australia, producing silver, lead and zinc. Mine ore is processed in a concentrator, which consists of grinding, flotation, thickening and filtration. Grinding is carried out in a fully autogenous (AG) mill. The mill operates in closed circuit with a pebble crusher. Throughput is approximately 380 tph. Cyclone overflow from the grinding circuit is fed into a flotation circuit for the recovery of lead, zinc and silver. Two concentrates are produced (lead and zinc), which are then thickened and filtered. The filtered concentrate is transported by road to a rail receiving station. From here the concentrate is railed to port in Townsville for shipment to the smelter. Matrikon and Engineers at BHP Billiton?s Cannington Mine have used ProcessACT to develop a flexible, nonlinear dynamic simulator for the grinding circuit to further enhance process understanding, as well to investigate various optimization strategies. An online charge volume estimator was also developed for the AG mill to aid in the understanding of overload conditions, which for the previous two months had been the primary contributor to downtime. The models were developed using a combination of first-principles modeling along with input-output dynamic responses. Examples of models used include: Morrell ?C? model for power and charge shoulder/toe angle prediction; Whiten?s mixing model for breakage and hold-up; Nageswararao cyclone model for predicting cut size; slurry recovery and water recovery. The composite model simulates system dynamics starting from the stockpile reclaim system and finishing at the feed for the flotation process. The objective was to provide a tool that assisted Cannington in understanding their Grinding Circuit and allowed them to develop and evaluate circuit optimization strategies. BHP Billiton Cannington Mine is now considering development of a Grinding Circuit Optimizer utilizing the models developed for the simulator.

Apr 1, 2005

By M Humphreys

Multi-episodic mineralisation is often characterised by different spatial trends exhibited by different generations of the mineralisation. The structural complexity of mineralisation together with the heterogeneous nature of the mineralised zones prevents unambiguous application of the conventional deterministic methodology for 3D constraining of the mineralised domains (ie conventional wireframing is ambiguous).A different approach, discussed in the present paper, includes a probabilistic definition of the domains encompassing one statistical population of the data. The domains are defined geostatistically using the indicator probability model. An indicator threshold is chosen for the definition of the high and low-grade domains. The spatial distribution of this indicator is then modelled by a variogram. The probability of exceeding the given grade threshold is than estimated by ordinary kriging for each modelled block. Blocks are then grouped according to their probability of exceeding the threshold and a continuous closed volume (domain) created from this likely patchy grouping using an appropriate structural model to fill the gaps). Methodology for the geostatistically assisted domaining is discussed in the paper. It is suggested that this technique represents an additional tool facilitating a structural interpretation of the mineralised zones.After the geostatistical domaining of the lode has been completed the grade within each of the domains is modelled using Uniform Conditioning method. Application of Uniform Conditioning for modeling the grade distribution has a significant advantage over linear methods (such as inverse distance or kriging) because Uniform conditioning enables estimation of local recoverable resources at different selective mining unit sizes that can be substantially smaller than the drilling density and are unable to be estimated directly.

Jan 1, 2002

Identifying Opportunities to Reduce the Consumption of Energy Across Mineral Processing Plants

Sep 13, 2010

By S Jokanovic, J L. Mauk

The Taharoa ironsand deposit covers approximately 16 km2 and is located 144 km south of Auckland on the west coast of the North Island, New Zealand. The heavy mineral-rich sands predominantly contain titanomagnetite, ilmenite and hematite, along with lesser amounts of amphiboles, pyroxenes, and feldspars. Throughout the Taharoa mine site 142 samples were collected of which approximately 25 samples were used in mineralogical analyses of the magnetic, heavy non-magnetic and light non-magnetic fractions. Mineralogical and petrographic analyses confirmed the high abundance of homogeneous magnetite and magnetite containing ilmenite exsolution lamellae which have oxidised to hematite. A limited number of sand samples were collected from Taranaki beaches. Petrography reveals exsolution textures of magnetite and ilmenite (now hematite), and homogenous magnetite grains similar to those observed at Taharoa. Petrographic analyses from previous research projects were also closely investigated in order to make mineralogical comparisons from along the west coast of the North Island and with other potential source areas. The origin of detrital magnetite grains along the west coast of the North Island is generally presumed to be the eroded volcanic cones of the Egmont volcanoes and active and dormant volcanoes of the central North Island. Electron microprobe analyses of magnetite grains from Taranaki beach samples reveal TiO2 values of between 1.5 and 120 per cent. MgO and A12O3 contents also vary widely from 0.75 to 6.5 per cent. This large variability may reflect different volcanic eruptions, the presence of exsolution textures or alternative source areas for these magnetite grains. Geochemical results from the Taharoa mine site correlate with the Taranaki beach samples suggesting that the Egmont volcanoes are certainly one source area. Variability in XRF results, especially Fe and Ti contents (9.04 - 59.22 and 0.80 - 4.64 respectively), from the magnetic and heavy non-magnetic fractions likely reflect the detrital nature of this deposit.

Jan 1, 2003