Search Documents

By L A. Maslov

We have considered the following characteristics of the crust and upper mantle of the Pacific Belt: seismic wave velocity anomalies, mechanical stress and shear deformation rate fields, heat flow and the pattern of metallogenic provinces of the Belt. It has been noted that there exist certain .regularities in distribution of the above mentioned geophysical characteristics and metallogenic zones within the Belt, displayed by prevalence of the lithophile elements in the Asia-Australian part of the Belt, and of the chalcophile ones within the American part.

Jan 1, 1995

From the time of its establishment in 1910, the Federal Bureau of Nines has studied the carbonization of coal, and a considerable part of this effort has been devoted to investigations in the so-called low-temperature carbonization range, 450° to 700° C., in which there is minimum decomposition of primary products and maximum yield of Liquids - a yield two to threefold the amount produced in high-temperature carbonization at 900° to 1,200° C, The solid residue, char, or coke, produced in low-temperature carbonization is 70 to 80 percent of the coal charged and may be used directly as a smokeless fuel or for blending with coals to produce metallurgical coke, Although some thought was given to the use of tar and to the illuminating value of gas derived from lm-temperature carbonization, the main emphasis in early work of the Bureau of Mines was on the preparation of smokeless fuel, especially for home use, For example, a carbonizer was designed and operated for making char and briquets from North Dakota lignite without recovery of by- products; however, the shortage of high-temperature coal-tar products in the United States during World War I had already indicated the potential usefulness of low-temperature tar.

Jan 1, 1959

By Vance G. Leak

Leaching of manganese from low-grade Minnesota ores was studied over the temperature range 25° to 225° C at atmospheric and elevated pressures to demonstrate that good recoveries of manganese could be achieved from unroasted ores using reagents available nearby. Various combinations of ore, pyrite, lignite derivatives, and sulfuric acid were tested on a small scale. Pyrite alone required the highest temperature to effect a good extraction, but the combination of pyrite, lignite char, and sulfuric acid solubilized 99 percent of the manganese after 30 minutes of reaction at 75° C.

Jan 1, 1971

By Michael J. Bertoldi

The purpose of this Bureau of Mines report is to describe the methods and establish the basic economics for dragline, shovel-truck, and scraper mining systems. An overall view of the techniques of preliminary design and the cost involved is presented. Considerations of equipment selection, emphasizing short-range evaluation of required equipment, and a long-range evaluation are considered at a constant production rate over the life of a hypothetical mine. Separate cost analyses for each system were based on 1977 equipment prices, prevailing wage rates, and associated mining costs. Specific engineering and cost breakdown for such items as access roads, transmission line installation, rail spurs, etc., are beyond the scope of this report.

Jan 1, 1977

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974

By Horst Pöchhacker

The largest structure along the Tauern highway section between Salzburg and Villach is the 6.4-km-long Tauern Tunnel. The major geotechnical problems that came up surprisingly while driving the headings of that tunnel and their successful solution form the content of this article. A detailed discussion is presented of the special construction methods developed by systematic application of the principles of the New Austrian Tunneling Method with which even very heavily squeezing ground with large excavation areas can be mastered reliably and economically.

Jan 1, 1976

By Philip W. Holland

This Bureau of Mines report discusses the results of three independent reconnaissance geochemical surveys conducted in the vicinity of the Bush Dome reservoir in the Bureau-owned Cliffside field near Amarillo, Tex. The surveys consisted of (1) determining the helium content of area ground waters, (2) determining the helium content of area soil gases and ground waters, and (3) determining the helium content of soil gases collected on a grid sampling pat- tern in the Cliffside field area. The native natural gas in the Cliffside field contains about 1.8 percent helium. To date, approximately 54 billion cubic feet of gas containing approximately 39 billion cubic feet of helium has been injected into the center of the Bush Dome structure. The research work, which was completed under contracts, was done to determine if helium concentration levels in ground water and soil gas could he used as an indication of the presence of helium in a subsurface natural gas accumulation. Results of the surveys were positive in that helium-in-water and helium-in- soil-gas anomalies were detected in portions of the Cliffside field area. All helium analyses were performed by mass spectrometric techniques.

Jan 1, 1979

By Rolf Katzenbach

The principle questions related to the design of deep foundations especially in soft soils are the stability and the cost optimised settlement reduction to prevent possible damages and to minimise the deformations of the adjacent infrastructure. The present develop­ments in the design of deep foundations lead to the design approach of the Combined Pile-Raft Foundation (CPRF) which offers a lot of new possibilities, e.g. the utilisation of the CPRF for horizontal loading or the use of the subsoil as a geothermal storage system.

Jan 1, 2006

By E. E. De Beer

This paper describes a method for the determination of the settlement of an individual H-bearing pile, based on the results of CPT-tests. As implied by the nature of the problem, no analysis performed on one pile can be regarded as generally valid for a whole piling foundation project because, even on one site, the pile behaviour varies from one pile to another. Consequently, no precise mathematical analysis has been established; the proposed procedure represents a simple model for the determination of the probable settlement behaviour of an H-pile under a compressive load. Prior to the settlement computations, the rupture load and the resistance distribution along the pile have to be determined. Since the method for the determination of the H-pile bearing capacity from the results of CPT tests has been described elsewhere (de Beer, 1971, 72; de Beer et al., 1982; Arbed, 1985), no details will be given in this paper. The proposed method is valid for both uniform and non-uniform H-piles. The computed results have been satisfactorely compared to the static loading tests performed on different types of piles in clayey and sandy soils during an ECSC research program on H-bearing piles (1983-1987).

Jan 1, 1987

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973

By Derrick D. Dasenbrock

Three piers of a new river bridge are supported on 1.067 m diameter open-end steel pipe piles. At time of drive, and after pile re-strikes, high-strain dynamic capacity values at plan tip elevations, were as low as 23% of design requirements. Pile lengths were extended 20% to 40% deeper than planned at two piers, driving to rock, impacting both the project cost and schedule. The significant discrepancy between predicted and observed capacity was investigated through a series of coordinated dynamic tests; a full-scale test pile was installed and monitored over 221 days by both dynamic and quasi-static methods. Unusually slow strength gains were observed by dynamic monitoring on all piles installed at the site. CPT soundings were advanced at the test pile and through the pile interior to investigate the soil plug. High-strain dynamic methods were found to have significant limitations in properly assessing the long-term capacity of large-diameter open-end pipe piles during driving and short-term pile re-strikes. As the benefits of large diameter high-capacity open-end pipe piles are numerous, the geotechnical community needs to address appropriate construction monitoring and control of these foundation types to take full advantage of these systems. An improved understanding of the physical effects of pile installation and the impact on soil strength assessment while driving and long term soil strength gain should be developed and incorporated into both design and monitoring procedures to avoid either unsafe or needlessly costly designs.

Jan 1, 2006

COALTECH 2020 initiated a research project to provide the coal mining industry with a modelling tool to determine the expected types of subsidence, risks and the investment required in post-closure funds to cater for subsidence associated with bord and pillar mines. A detailed literature review was conducted to determine the most important parameters in calculating the cost associated with surface subsidence. A subsidence prediction model was developed to determine the likelihood of different types of subsidence. The study made use of current knowledge of failure mechanisms and its aim is to assist the industry and government in arriving at the most suitable arrangements when authorities require financial instruments to assure compliance with environmental regulations.

Jan 1, 2003

These proceedings consist of an introduction and four descriptive papers. The first paper is an update on fire protection for large haulage vehicles, the second paper is concerned with improved visibility systems for large haul- age vehicles, the third paper is on improved ladders for large haulage vehicles, and the fourth paper is concerned with large haul-age vehicle operator training systems.

Jan 1, 1980

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, Nevada began large-scale production in 1977. During 2008 Round Mountain Gold Corporation (RMGC) relocated the primary crusher facility approximately 300 meters (1,000 feet) to make room for the next phase of open pit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17 meter (56 feet) high Mechanically Stabilized Embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, Colorado. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design, and construction of the MSE wall.

Jan 1, 2009

By Dan Alexander, Ivan Crnkovic, Sarah Schwarz

"Several plant studies have been conducted at the Zinifex Century Mine over the past 5 years. For each of the plant studies, surveys of the zinc primary circuit were conducted, characterisation measurements for each operating cell taken, and the floatability components of the ore mapped to develop a model of the circuit. The floatability components and machine parameters were then used to simulate changes in circuit configuration and operating conditions, enabling further potential improvements in circuit performance to be identified.This paper reviews the current flotation practice at the mine, as well as various circuit changes and developments implemented by site. The application of the methodology and the evolution of the standard procedure are also discussed.INTRODUCTIONBase metals were first discovered in the Lawn Hill region of Queensland’s North West in 1869 and the first mining lease in this area was pegged in 1887 over what is now known as the Silver King vein deposit. The area encompassing these veins, which includes the Century deposit, was proclaimed the Burketown Mining Field in 1899. Exploration titles were granted to CRA in 1987, precisely 100 years after the initial discovery at Silver King, hence the name ‘Century’.Century was commissioned by Pasminco in late 1999, with the mine becoming fully operational on 1 March 2000 and the official opening taking place in April. Pasminco had bought the Century and Dugald River deposits from CRA in 1997 for A$345 million, and invested some A$710 million in bringing Century into production. Today, Century is the world’s second-largest zinc mine in terms of its output, having reached full capacity in 2003.The Zinifex Century Limited (“ZCL”) lead-zinc-silver deposit is located approximately 250 kms north-north west of Mt Isa in north-western Queensland. The deposit is a large flat-lying ore body covering an area of some 1.2 by 1.4 km, the 45 m-thick stratabound sulphide orebody is hosted within an 850 m-thick sequence of Proterozoic siltstone, shales and sandstone, amenable to open-cut mining methods. The mine has ramped up to full production delivering five and a half million tonnes of ore per annum, yielding approximately 900,000 tonnes of zinc concentrate and 90,000 tonnes of lead concentrate. Mine life is expected to be about 8 years"

Jan 1, 2008

By R. L. Grayson, F. Giana, R. Aspinwall

Small-mine and contractor Fatal Incidence Rates have been a problem for over 20 years in the coal industry, and the rates persist as unacceptably high. This paper briefly retraces historical information and data on the continuing problem and recounts the many unsuccessful efforts and initiatives to address the problems effectively. Next the results of a review of international literature on addressing the problems are presented. After focusing on a method to pinpoint the trouble spots more specifically through a nested data analysis, suggestions are provided on how the problem may potentially be addressed more systematically and effectively in the U.S.

Jan 1, 2006

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By Richard E. Bischke

Computer assisted finite element model analysis, originally developed to study stress distributions in aircraft, has been modified into a versatile mining program, that can be used to assist the engineer with predictions of mine subsidence. International Exploration, Inc. has developed an in-house finite element model program which incorporates a multitude of factors influencing mine subsidence such as mine design, physical rock properties, structure, faults, joints and topography. Finite element analysis of a mine model can mathematically determine the magnitude and direction of the principal stresses within each of the elements forming the model. By comparing the calculated in-situ stresses to the actual rock strengths, high risk regions within a mine can be identified. These potentially unstable regions of the mine can be allowed to fail within the model and the resultant stress redistribution and element movement calculated. Thus, the effects of the mine collapse at the surface can be predicted for the purpose of determining the potential damage, if any, that could occur to surface structures from deep mine failure. Stabilization materials can also be mathematically inserted into the model to design and analyze the effectiveness of subsidence prevention programs. Two examples are presented of the finite element program being used to predict mine subsidence at substantially different geologic and mining provinces in Pennsylvania.

Jan 1, 1984

By E. LaRocque

"Long term contracts requiring delivery of 6,000,000 pounds of U308 per year to its customers have made it necessary for Denison Mines to expand its milling capacity from 7,100 tons per day to 15,000 tons per day.Previous papers (1) and (2) described the old leaching and product recovery practice. The flowsheet briefly includes a crushing and grinding circuit, sulphuric acid leaching in a Pachuca plant, liquid-solid separation with wash thickeners and two-stage drum filtration, concentration and purification by moving bed ion exchange followed by two-stage precipitation to produce an ammonia yellowcake.No. 1 Shaft ore, about 4,000 tons per day, will be processed through the truck dump into the old crushing and grinding plant and through the old leaching plant. Ore from Stanrock (No. 3 shaft) will be hauled by truck and also processed through the truck dump as No. 1 shaft ore. Beginning in 1982, ore production from Stanrock will gradually increase until 1985 when some 3,000 tons per day will be milled from the source.A new 8,000 ton per day circuit was designed and constructed to increase the milling capacity to 15,000 tons per day. The new circuit is separate from the old one except that it coins together for the precipitation and tailings neutralization sections of the plant. The feed to the new plant will be from No. 2 shaft.The flowsheet is much the same as the old plant with the exception of the grinding circuit and the ion exchange plant. A semi-autogenous grinding (SAG) plant, unique in the Elliot Lake area, has been installed rather than the conventional crushing and grinding plant; the ion exchange plant is the stationery bed type.This paper describes the major equipment installed for the expanded grinding and hydrometallurgical plant."

Jan 1, 1982

By D. Bedell, J. Robitalle, D. Macgilliveray

Agnico Eagle (Cadillac Quebec, Canada) selected the new Eimco PEC E – CAT™ clarifier thickeners for their counter-current decantation circuit, which handles approximately 200tph leached gold/silver ore. The E-CAT is based on rakeless ultra-high rate thickening technology that originated in South Africa. Four 9m diameter and two 10m EIMCO E – CAT ultra high rate, rakeless thickeners were installed in the fall of 2000. Thickening and clarification performance has been excellent. Problems with level control have been resolved and the plant personnel continue to improve the operating control techniques. The CCD circuit is critical to the success of the operation and good recovery. Data will be presented showing the wash ratios and recovery achieved. A brief history of the operation and the decision to utilize the CCD system will be presented.

Jan 1, 2002