Search Documents

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite with length-to-diameter (L/D) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite) were tested to failure in axial compression to determine to what extent an increase in end constraint increased compressive strength. Adjustable steel rings, mechanically tightened about the ends of test specimens to create a radial prestress of 3,000 or 5,000 psi prior to the application of axial load, increased end constraint more than was possible in previous tests using solid steel rings. (Solid rings, epoxy-bonded to the ends of dogbone specimens, increased compressive strength compared with that of straight specimens without ring constraint.) During the loading cycle, additional end constraint was produced by lateral expansion of the specimens against the rings. The effect of the end constraint was to increase the compressive strength 55 to 58 percent for the shorter pillars of dogbone shape compared with the compressive strength of straight pillars with the same L/D ratios without ring constraint. Most pillars with L/D ratios of less than 2 were made stronger by end constraint. Pillars with an L/D ratio of 3 did not benefit significantly from end constraint. When the results from compression testing of straight specimens of rock in the laboratory are used to design mine pillars in situ, the pillars will be larger than necessary if the horizontal compressive stress is several thousand pounds per square inch greater than that resulting from the weight of the overlying rock alone. The L/D ratio can be increased by a factor of 1.76 for ratios in the range 0.25 to 3 and still provide the same compressive strength. The safety factor applied with straight specimen test results should also be acceptable for use with constrained pillar test results.

Jan 1, 1969

By Gustavo Armijo

Slippery and unstable working platforms spoiled not only by natural weather conditions but also by the effects of the construction process (drilling mud, grout slurry) are among the main sources of hazards. Due to this fact a set of recommendations for execution and maintenance of working platforms are presented in this paper, which is based on a study on this subject that is being carried out by AETESS, the Spanish Federation of Geotechnical Contractors. The main objective of this paper is to establish the basis for the right execution and maintenance of working platforms for geotechnical jobs with the idea of increasing safety and productivity. All the aspects involved in working platform safety are analyzed: ground and equipment characteristics, geometric conditions and working platform maintenance. From this analysis a set of general requirements is proposed together with the necessary specific controls before and after the equipment arrival to the job site. In order to facilitate this analysis some flow charts and tables and specific appendixes for each geotechnical technique are included.

Jan 1, 2006

By James S. Browning

Recovery of fine mica from a sample of impounded tailing from the Dixie Mines, Inc., crushing and screening operations, Heflin, Ala., was investigated to determine if plant losses of mica could be reduced while econmically producing a commercially acceptable mica concentrate. Conventional wet-tabling and agglomerate-tabling methods yielded concentrates assaying about 95 percent mica from the tailing that contained 17 percent mica. Products containing about 98 percent mica and accounting for mica recoveries of 86 percent were obtained by flotation, using as reagents sulfuric acid, kerosene, and coco amine acetate (a mixture consisting chiefly of dodecyl and tetradecyl amine acetates). The results of the batch flotation tests were verified by tests in a small continuous flotation pilot plant.

Jan 1, 1963

By D. Kwietnewski

The 4th bore of the Caldecott Tunnel is a 50-ft horseshoe shaped highway tunnel located in the hills east of Oakland, California. Tunnel excavation was mostly completed using one of the world?s largest commercially available roadheaders, a Wirth T3.20. The geologic profile included seven different geologic units, which displayed a range of different behavior with regard to excavation and initial support. Following a brief introduction to the excavation and support methods, this paper will discuss roadheader performance in the various geologic units encountered during excavation. Comments will also be made concerning the relationship between the roadheader method of excavation and observed ground convergence during excavation.

Feb 27, 2013

By Dave Price

"Canada is scheduled to become the 4th highest diamond revenue producing country in the world by year 2004 with the already operating Ekati Mine and the anticipated operation of the Jericho Mine in 2002 and the Diavik Mine in 2003.This paper provides an overview of worldwide diamond production statistics and a brief introduction to a diamond processing plant. The dense medium separation (DMS) extraction process is presented and this process is discussed in more detail with respect to the extraction of diamonds in terms of feed preparation, dense medium, dense medium cyclones, ferrosilicon recovery and dense medium cyclone operating efficiencies.INTRODUCTIONThe Ekati Diamond Mine in the Northwest Territories started commercial production of diamonds in the 4* quarter of 1998. At full production, the mine is anticipated to produce annually some 3 million carats of diamonds. The Jericho Mine in Nunavut Territory and the Diavik Mine in the Northwest Territories are anticipated to come into production in the 1'' quarter of 2002 and 1st half of 2003 respectively. The combined annual diamond production of these three mines will total approximately 10.34 million carats by 2004, making Canada the 4~ highest diamond revenue producing country in the world.A diamond processing plant initially utilizes crushing, scrubbing and screening in the beneficiation process to liberate diamonds from kimberlite ore and size the product for further treatment through DMS. Alluvial diamond operations do not require initial crushing and scrubbing but incorporate a feed preparation and sometimes a recrush facility with the DMS plant. The heavy sink product from the DMS, which contains diamonds, is further upgraded through x-ray separation and high intensity magnetic separation prior to producing the final diamond product.DMS is a relatively simple separating principle. A mixture of particles of different density is immersed in a dense fluid, so that particles having a density lower than that of the fluid will float while those of heavier density will sink. The translation of the float-sink principle from a laboratory method to continuous industrial practice offers the prospect of very precise mineral separations based on density differences alone."

Jan 1, 2000

The gold concentration profiles which develop inside the activated carbon particles during the adsorption process were measured, so as to obtain additional direct proof of intra-particle mass transfer rate-control and to determine how individual carbon particles in a population vary in their gold uptake behaviour. The observed gold concentration profiles inside the activated carbon particles were typical of situations where an intra-particle mass transfer mechanism is rate-controlling. Gold di-cyanide penetrated the carbon particles with a wave-like front until it was uniformly distributed throughout the particle. This corresponds with the profiles predicted by the film and surface diffusion model. However, the rate with which gold di-cyanide was transported inside the individual carbon particles varied within the population of carbon particles. This variation was characterized by a lognormal distribution in surface diffusivity. Because the estimated variances of these surface diffusivity distributions were small, the dynamic adsorption behaviour of the carbons used in the present study did not deviate significantly from that predicted by a model based on film mass transfer and a single surface diffusivity. Van Deventer (1984, 1985 and 1986a) reported data that could not be adequately described by a model based on film mass transfer and a single surface diffusivity. In this study a model based on film mass transfer and a wide lognormal distribution of surface diffusivity values was applied to his data. It was shown that a population of carbon particles with a wide distribution in surface diffusivity values could offer an alternative explanation to the mechanism proposed by Van Deventer which was based on film mass transfer, with partitioning of the carbon into micro- and macropores with surface diffusion in the macropores and slow mass transfer into the micropores.

Jan 1, 1997

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from, the underlying unoxidized ore through prolonged weathering. The degree of oxidation in different sections and at different depths within the bed is nut. uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By I. Yildirim

Free energy of interaction between particles in water can be calculated if one knows the values of appropriate interfacial tensions, which in turn can be determined from the surface free energies of the particles involved. The latter can be determined using the Van Oss-Chaudhury-Good (OCG) equation. This method requires the measurement of contact angles of well-defined liquids on the surfaces of the particles of interest. In the present work, the contact angles were determined using heat of wetting, capillary rise, and thin-layer wicking methods. The results are compared, and the utility of the surface free energy data obtained from the contact angles are discussed.

Jan 1, 2002

By Ch. Schroeder, F. Collin, R. Charlier, Y. J. Cui

The paper proposes two numerical models ot the mechanical behaviour of chalk. First, an elasto-plastic constitutive law reproduces the different plastic mechanisms of the chalk and the influence of pore fluids by introducing the concept of suction. Secondly, a model able to reproduce time dependence behaviour. Eventually, the paper gives a simulation of an academic reservoir during depletion and waterflooding phase. Der Artikel stellt zwei numerische Modelle des mechanischen Verhaltens der Kreide vor. Das erste ist ein elasto-plastisches Modell, das verschiedene plastische Mechanismen der Kreide und den Einfluss von Porenflüssigkeit, unter dem Begriff der Suktion, reproduziert. Das zweite Modell berücksichtigt darüberhinaus das zeitabhängige Verhalten. Schliesslich zeigt die Veröffentlichung eine Simulation einer theoretischen Lagerstätte während der Entleerung und der Wasserinjektion. L'article propose deux modèles numériques du comportement mécanique de la craie. Le premier est une loi élasto-plastique qui reproduit les différents mécanismes plastiques de la craie et l'influence du fluide interstitiel par l'introduction de la notion de succion. Le second est un modèle prenant en compte les effets différés. Enfin, l'article présente une simulation d'un réservoir académique durant les phases de déplétion et d'injection d'eau.

Jan 1, 2003

Of the world's total production of gold the largest proportion comes from the more regularly consistent ore bodies, but in the aggregate an important part comes from those which are often irregular, uncertain and small. These smaller ore bodies are often high in grade and, as the capital required to work them is not large, they appeal to people seeking a quick and profitable return for a small outlay.These small mining concerns cannot afford detailed geological and petrological investigations and mapping, so they are very often dependent on local knowledge and experience which admittedly may be of really great value.Nevertheless the absence of skilled guidance may not only cause good opportunities for intelligent exploration to be lost, but discourage the seach for other ore bodies.lVIining engineers in the course of their travels in the examination of mines often come across such cases and also others where problems of finding lost ore bodies have been solved by the man on the spot. As records of cases are valuable and useful additions to the knowledge of ore occurrences, the writer now proposes to describe one such case coming under his observation in recent years.It is that of a small mine, known as the Idaho, at the southern end of the famous "Golden Mile" at Kalgoorlie (see Fig. 1). This mine has been a small and very erratic producer ever since it was abandoned by an English company which owned it forty years ago. Except for one period of four years it has always been owned and worked by parties of co-operative miners and during its time has gone through a tortuous career. Although it has often...

Jan 1, 1938

As part of its research and development activities concerning coal mine operational/emergency communications sys terns, the Bureau of Mines commissioned several contractors to conduct electromagnetic (EM) noise studies and measurements that would aid the development of improved coal mine operational/emergency communications systems. The bulk of the noise studies and measurements were conducted in 1971. The Pittsburgh Mining and Safety Research Center (PMSRC) inherited the responsibility for monitoring the electromagnetic noise activities by mid-to-late 1971, and initiated a review and evaluation of the current and planned electromagnetic noise work. Arthur D. Little, Inc., (ADL) was asked by PMSRC to assist it in performing this review and evaluation by placing stronger emphasis on certain tasks of existing Contract No. H0122026. This technical memorandum report presents the findings, conclusions, and recommendations of our review and evaluation of the electromagnetic noise measurements of the five contractors we were asked to examine. Our review and evaluation effort included meetings and telephone discussions with technical staff of each contractor; serving as Technical Discussion Leader of a "Contractor's Round Table Meeting on EM Noise, Surface and Subsurface, Operating and Non-Operating Mines" called by the Bureau of Mines; examination and discussion of contractor reports and relevant open literature; sample verification calculations; and the documentation of our findings, conclusions, and recommendations by this report.

Jan 1, 1972

By Mary Cocklan-Vendl

Regulatory processes associated with development of a world class lead-zinc mine, Red Dog Mine, in northwestern Alaska were reviewed and evaluated. Informal interviews with key project personnel, consultants, and agency field and permitting specialists provided perspective on the regulatory successes and failures of the project. Due to potential impacts to air quality, water quality, wetlands, and National Park lands, an Environmental Impact Statement was required. By developing a comprehensive baseline of information on the existing environment to aid in minimizing impacts during project siting/design and through regular coordination of evolving project plans with regulatory agencies, the mine developers were able to acquire necessary permits in a timely and cost effective manner. The only major exceptions occurred when inadequate information was collected on dispersal of airborne particulates, rates of surface water run-off, and groundwater quality. These deficiencies resulted in the need for design changes, unscheduled construction, additional environmental monitoring costs, and delays in issuance of the NPDES permit.

Jan 1, 1992

By Erik Westman

Coal bumps remain one of the industry?s most devastating but least understood phenomena. If changes to the internal conditions of the rock mass could be observed there is hope that bumps could be forecasted. Seismic tomography has been used over the past 25 years in an attempt to image these changing conditions in the vicinity of the longwall face. This paper describes the history and practical considerations of using seismic tomography in bump-prone coal mines. The implementation of seismic tomography at six different longwall mines will be described along with lessons learned. Early studies used mining independent sources of seismic energy, including explosives and sledgehammers. Subsequently more operator friendly sources, such as the mining equipment itself and mining-induced seismicity, were used. Seismic energy sensors have been placed in gateroads and on the surface above the mine. Each of these configurations has associated advantages and disadvantages. Although the results obtained have been encouraging, the application of seismic tomography to monitoring a bump-prone longwall face is still immature. The ultimate goal of clearly imaging changing stress conditions in the longwall panel in a manner that does not inhibit mining operation is still distant, yet drawing nearer. When this goal is achieved, the industry will have a capable tool for identifying locations where bumps are imminent.

Jan 1, 2008

By Andrew Jones

This paper discusses the worldwide market and cost environments for the bulk ferroalloys namely manganese alloys (ferromanganese, silicomanganese), ferrosilicon and ferrochrome (high-carbon ferrochrome, charge chrome). Annual average market prices since 1993 are presented graphically and analysed, and the main supply and demand trends for manganese, ferrosilicon and ferrochrome are summarized. The paper shows carbon and stainless steel output data for 1995, 2000 and 2005, mainly to demonstrate the rising importance of China as a ferroalloys market. Developments in ferroalloys capacity worldwide from 1991 to 2007 are discussed (plant start-ups and closures, ownership changes). Finally, the paper examines developments in the main cost factors for the bulk ferroalloys, i.e., chrome and manganese ore, electricity, carbon reductants and labour. Note that data for 2006 are estimated based on information available in November 2006.

Jan 1, 2007

By Bruce Hebblewhite

This paper focuses on the recent achievements and practices developed through the Minerals Tertiary Education Council (MTEC) initiative of the Minerals Council of Australia (MCA), in conjunction with the three partner universities involved in mining engineering education – University of New South Wales (UNSW), West Australian School of Mines, Curtin University (WASM), and University of Queensland (UQ). The collaboration between these partner universities and industry has led to the development of shared course material, cross-institutional teaching arrangements, and development of a number of flexible, distance-based delivery programs. The paper will then move on to future initiatives. Importantly, the exciting challenge is the future initiative planned to cement this collaboration by the formation of a “virtual” national school of mining engineering – Mining Education Australia (MEA). This will provide a common 3rd and 4th year program to all three universities from 2007, involving innovative teaching and learning arrangements, greater student exchange potential and a more significant input by industry into the education process. Such an initiative is not without its challenges, and has a long way to go, before becoming a reality. However, it offers greater attractiveness and marketing potential to prospective students, as well as economic efficiencies, whilst delivering a better quality, and hopefully greater quantity of graduates to industry. It can also form a launching platform for a much greater level of international collaboration, through a proposed International Mining Education Network (IMEN) which is currently being floated amongst a number of international educators.

Jan 1, 2005

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

By John R. Hoskins

The Bureau of Mines conducted an investigation to more exactly define the influence of some end conditions on the laboratory-determined uniaxial compressive strength of rock samples. Limestone, marble, sandstone, and granite were used to provide a range of specimen modulus of elasticity from 2.7 X 106 psi to 10 x 106 psi. Four variables were studied: Nonparallelism and surface texture of specimen ends were the specimen variables investigated; the end platen size and the adjustable or spherical head friction were the machine variables studied. It was concluded that the loading ends of small laboratory models and samples should be prepared with surface irregularities that do not vary from a plane surface by more than 0.001 inch. It was also concluded that nonparallelism of the specimen ends should not exceed 8 minutes for a rigid head load or 15 minutes for an adjusting head load. The measured compressive strength of specimens prepared with these tolerances will be statistically the same with any diameter or thickness of platen and any degree of head friction if initial alinement of the specimen is assured.

Jan 1, 1968

By A. Bascetin

Waste materials caused by mining activities are an important environmental problem. Paste technology is a good alternative for waste management because it has many benefits in the aspects of environment, cost and safety. Disposal of process wastes in paste form is an attractive option for waste management, as it eliminates or reduces the risks associated with conventional methods. Due to the geotechnical characteristics of the paste, it is very similar to soil materials. So determining the geotechnical properties of the paste material is essential to durability of the paste. The some important geotechnical properties are compressive strength, porosity, shear strength, hydraulic conductivity, water content, consolidation, etc. In this study, the important parameters and the relation between them were investigated and obtained some results which will affect for optimum design of waste management.

Jan 1, 2012

By V. R. Miller

The Bureau of Mines developed and evaluated a detecting and sorting device to separate the copper-bearing portion from the barren portion of Michigan native copper ore in the minus 4- plus 1-inch size range. Small-scale sorting tests were also conducted on minus 1- plus 1/2-inch material from the Centennial No. 6 mine, using a previously developed system that was modified to increase sensitivity. Results showed that, with the added sensitivity, 85 to 90 pct of the copper in the minus 1- plus 1/2-inch material could be recovered in about 50 to 60 pct of the fraction. Sorting tests on minus 4- plus 2-inch and minus 2- plus 1-inch fractions from the Centennial mine were conducted with the large sorting system. Results showed that 86 to 93 pct of the copper was recovered in 43 to 64 wt-pct of the sorted fractions. Combining of concentrates from the two fractions resulted in a recovery of 90 pct of the Popper in 55 pct of the weight. The composite concentrate contained 2.40 pct copper, and the tailing analyzed 0.33 pct Cu; the head sample assayed 1.46 pct Cu.

Jan 1, 1978

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996