Search Documents

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

By P. Golledge, A. D. S. Gillies

An investigation has been carried on samples of three Queensland coal dusts to determine the potential explosibility of dust-gas mixtures. The explosion potential of the samples was classified by the lean and rich limits of explosibility and the limiting oxygen concentrations for each sample. Plotting of these points showed 2-dimensional flammability limit surfaces for coal dust/oxygen, methane/oxygen and coal dust/methane mixtures. From these plots the 3-dimensional flammability envelopes defining the explosibility of the mixtures were defined. The explosion limits of the coal dust/methane/oxygen system were seen to be influenced most by the explosibility characteristics of coal dust. Methane exerted a stronger influence over the explosion limits when the coal had a low volatile content

Jun 19, 1905

By Hongfei Li, JianLong Wang

This paper introduces the technical characteristics, transformation scheme and production practice of the project in which Copper P-S Converter was replaced by Bottom Blowing Continuous converting for the first time, and introduces the technical achievements obtained by the project. The application practice proves that bottom blowing copper continuous converting technology can completely solve the problems of fugitive off-gas pollution in the ladle transportation, large amount of flue gas and fluctuation of flue gas caused by P-S converting. Comprehensive energy consumption and operating costs of producing blister copper, safety and environmental risks are greatly reduced, and economic, environmental and social benefits are significant. It is one of the preferred technologies for upgrade and to replace P-S converting technology. INTRODUCTION At present, more than 80% of copper production capacity is still using the P-S converting technology with a history of more than 100 years. During P-S converting process, melted copper matte needs to be transported by ladle, and it needs to rotate the furnace body several times, causing a lot of serious environmental and safety risks such as SO2 flue gas emission and low-altitude SO2 pollution. In addition, the high operating cost caused by low rate of air blowing, the short life of the refractory materials and high energy consumption during P-S converting become big problems. Other problems such as large amount of flue gas, low SO2 concentration, large fluctuation of flue gas volume and SO2 concentration, and discontinuous flue gas cause high cost of subsequent flue gas treatment are also needing to be solved. In order to solve these problems during the P-S converting, metallurgical engineer in various countries has spared a lot of efforts to develop continuous blowing process for decades. The continuous converting that have been industrially applied are flash continuous converting, Mitsubishi continuous converting, Noranda continuous converting, Bottom Blowing Continuous converting and multi-lance top blowing continuous converting

Jan 1, 2019

By M. K. G. Whateley, W. Hatton

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 20pp., 31 refs. Estimates of coal tonnage on UK open cast mining sites often vary from the recoverable tonnage. This is because the estimates depend on the geological variability of the coal measures. Geological parameters, such as thickness, quality and disturbance of the seam, have a direct control upon this variance. Risk analysis techniques have been applied using commercially available software to combine each parameter's variability into a cumulative variance, resulting in a tonnage distribution. Sensitivity modelling has also been used to identify the geological parameters which have the largest influence on the variance of the simulated tonnage distribution. An understanding of the relationship between the tonnage and geological variability has helped to focus exploration more efficiently. A cost to risk relationship can now be monitored, helping management to avoid negative consequences on site

Aug 1, 1995

When the mining and milling of 1100 copper orebody commenced at Mount Isa a satisfactory grade of copper concentrate was difficult to produce. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in inherently flotable fine pyrite and siliceous particles.The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1971

By Malcolm Arnesen

Mineral Resource Management (MRM) is a business concept with the purpose of increasing throughput by management of key process variables to optimize ore utilization. To achieve a MRM process focus there are four principles that need to be applied to the business. In this sense, the paper define these principles and describe how they are applied to the mining business using Thabazimbi iron ore mine as an example. Also the article deals with the generic approach to Mineral Resource Management and the second part with the application and success of MRM at Thabazimbi Iron Ore Mine.

Jul 17, 2000

By John Watson, Tom Treleaven

This guide presents nur-nerous patterns that provide 8 millisecond separations between initiated charges. The guide is tabulated in seven sections to provide Quick reference by number of decks or bunch blasting. The pattern IS presented in the section where the highe!$ number of decks works. It should be noted that patterns applicable to multipledackshwtings are alsoapplicsblefor fewer decks.

Jan 1, 1995

By M. G. Senyur

This study aims at investigating the structural characteristics of backfilling material. In this regard, spatial arrangement of solid particles and associated voids in a unit mass of coal mine refuse as backfilling material were tested. The materials were produced from coal mine refuse of Zonguldak Colliery, Turkey. The experimental procedures were developed to determine their void ratio (or its equivalent porosity), bulk density and the shape properties of constituent particles. The orientation fabric and the co-ordination number were the other two fabric elements determined. The filling materials were sieved and their particle size distributions were found. The results obtained by experiments were related to the particle size distribution parameters, namely, the coefficient of uniformity and the effective size. It was concluded that mean value of void ratio is correlated with coefficient of uniformity. The standard deviation of porosity as an index of fabric heterogeneity is clearly correlated to effective size. By an original experiment, the frequency distribution of coordination number was observed as binomial in uniformly graded materials. Also, the co-ordination numbers of test mixtures were calculated by the Marsal method and results obtained showed a good correlation between the minimum particle size and number of contacts per unit area.

Jan 1, 1998

By L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, Colorado, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained, and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward sloping (20 pct) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

A model has been developed as part of the AMIRA P420 Gold Processing Technology Project to simulate the recovery of gold by centrifugal gravity devices. The model (which is available online) uses the simulation methodology developed by Laplante et al (1995) to predict gravity recoverable gold (GRG) recovery under varying operating conditions and circuit configurations. In addition to predicting GRG recovery, the model also predicts the GRG content and size distribution of the cyclone overflow and underflow. The predicted overflow GRG content and size distribution can be used as inputs for a leaching model in which size dependent leaching rates are applied for each size class of GRG and non-gravity recoverable gold (non-GRG) in the cyclone overflow, allowing size-by-size leach recoveries to be determined for GRG and non-GRG. The application of the gravity model and leaching model are demonstrated using a case study. The simulated gravity recovery and leaching performance showed excellent agreement with the measured values. The developed models can be used to assess the sensitivity of gravity gold and leach recoveries to varying feed GRG content, GRG size distribution, gravity circuit feed rate, classifier performance and leach residence time. The described methods can be used to optimise new and existing gravity and leaching circuits.

Aug 1, 2010

This paper reviews the likelihood of instability occurring within coking coal cargoes from BHP CoalÆs northern Bowen Basin mines. In coal cargoes, initial moisture redistributes vertically towards the base, saturating the bottom layers unless the bilge wells are pumped regularly. There has been concern in some quarters that saturated coal in the basal layer may be prone to liquefaction, and if the vessel then rolls significantly in rough seas, overall sliding movement of the cargo might occur. However, a review of shipping accident statistics reveals that casualties relating to shifting of coal cargoes are quite rare, and have not occurred in modern large bulk carriers (>15 000 dwt). The moisture redistribution process has been analysed to quantify the extent of cargo saturation that may occur. Results indicate that the amount of redistribution increases with initial moisture content above a threshold of eight to nine per cent. However, the removal of water by pumping from the bilges is remarkably effective in reducing the extent of saturated coal (and therefore the possibility of cargo liquefaction and movement), and in controlling the average moisture content of the bottom layers of cargo. Stability analyses were then performed for deep sliding of a cargo with a saturated and liquefied base. These have confirmed that sliding of a cargo with a liquefied base during rough seas (20¦ roll angles) would require initial total moisture content exceeding 13 per cent, the hold half full or less (width/depth >3), and no bilge pumping so that height of the saturated zone is as deep as possible. Overall, the results indicate that coking coal cargoes from BHP CoalÆs northern Bowen Basin mines will be unlikely to suffer sliding or liquefaction failures when transported in modern large bulk carriers.

Jan 1, 1997

By SH. Shahsavari, H. Akbari, M. Noaparast, M. Oliazadeh

Mejel valley zircon ore in Iran is located in north part of Iran and was sampled to evaluate its concentration. The aim of this project was to define the mineralogy of this zone and separating zircon from other minerals using gravity concentrators and magnetic separators. It is constituted of various valuable minerals, mainly zirconium, niobium-tantalum, titanium, rare earth elements particularly cerium-bearing minerals namely zircon, sphene and rare earth elements oxides. We used statistical method for designing of experiments. Yates method used for analysis of basic experiments results. The grade of zircon in primary sample was 1.1%. Different experiments were designed to optimize all required parameters. The final concentration with 75% zircon was produced and final recovery was 79%. Finally, lab-scale based flow sheet was prepared using experiments results.

Jan 1, 2005

By J. A. Hudson, X. D. Pan

A rock mass responds to excavation according to the properties of the intact rock, the network of contained discontinuities and the susceptibility of the rock mass to weathering. Large deformation often occurs when one of these components causes the rock mass to have a low strength relative to the stress conditions. Analysis of such large deformations forms a significant feature of current numerical modelling in rock mechanics. A practical large deformation problem of roadways in a coal mine is described, demonstrating the requirements for improving numerical techniques. The development of a numerical model is then summarised with particular attention to several concepts pertinent to large deformation analysis in geomechanics. A numerical case study is presented in which the developed finite-element model is used and the results are compared with the in-situ measurements. Conclusions are drawn for rock engineering that are also relevant to both civil engineering and mining engineering projects

Sep 1, 1991

By Galen G. Waddell

This report describes a method of measuring and analyzing the initial deformation which occurs in the medium surrounding a mine accessway as the opening is created. Discussed are (1) the hypothesis upon which the research is based; (2) the in situ rock-deformation measuring equipment developed; (3) the field tests, consisting of measuring the deformation of the medium around two 4-foot-diameter raise bores as the boring progressed; and (4) a finite-element technique to correlate theoretical with experimental results, using elastic theory. Described also are the raise-bore operation and performance. The instrumentation developed proved to have the sensitivity and resolution necessary to measure rock deformation around a full-scale raise bore during excavation. Tests show the relationships of rock deformation to progress of the raise boring and to time. The initial deformation of the opening appeared to be elastic. Using the deformation records and an estimated field stress, the modulus of elasticity was determined for the rock mass. In addition, the importance of this type of measurement in assessing support-problem areas is discussed.

Jan 1, 1971

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By George A. Lawrence, J. C. McHardy

"Field operating experience with an improved flotation mechanism for handling various flotation applications is covered in this paper. Some aspects of designing flotation machines are also presented. Operating data from extensive testing of commercial size equipment under actual plant operating conditions in the following applications is detailed:1. Copper Flotation2. Fine Coal Flotation3. Base Metal Sulfide FlotationDesign features, design improvements, modifications tested, and overall performance data are reviewed. Some mecl1anical performance data as well as metallurgical performance results are presented. Some comparisons with conventional flotation equipment are reported in this paper.Flotation sizing theories are reviewed and an actual equipment selection ex2.mple is presented. Scale-up criteria used for developing large cells are briefly covered.The paper concludes with a brief review of anticipated future flotation equipment design needs. IntroductionThe mining/milling industry is faced with increasing pressure to cut costs while maintaining product quality and indeed, in some instances, expanding production. For copper, nickel, iron, molybdenum, lead and zinc sulphides, coal, phosphate and some other minerals;, flotation remains the primary method of concentration and recovery of the valuable mineral away from the gangue. Cost reduction in flotation can be broadly focused on two areas:1. Flotation Chemicals2. Flotation Equipment"

Jan 1, 1985

By Sashir Estela De la Cruz

Actualmente la informática como herramienta aplicada al sector minero nacional, es importante -en tanto su empleo adecuado y racional implica alcanzar los objetivos planteados en forma más rápida y con mayor calidad. En este sentido, el presente texto describe el sistema informático que genera soporte al trabajo de modelamiento geológico para la estimación de reservas mineras, de forma que reduce el tiempo y personal empleado en dicha labor. Este sistema se divide en dos partes: estadístico y gráfico y determina la explotación de un prospecto de yacimiento minero.

May 25, 1998

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores, and rock minerals is constantly required to develop new means acid methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes of physical separation. Thus, in 1919, Coghill and Bonardi 3/ published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/ Schwartz 5/, and Head and his associates 6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and the University of Alabama.

Jan 1, 1940

By Ming-Gao Qian

How to monitor and control the support and surrounding strata system on a longwall face effectively is one of the major research problems in ground control. Based on observations on movements of the support and surrounding strata of face No. 2703 of Dongpang colliery, the relationship between the downtime related to support and surrounding strata and other influential factors is analysed systematically in this paper. Monitoring indices and control measures are then determined by taking corresponding downtime as an objective function. When the monitoring method, developed from the above findings, was used on face No. 2703, the downtime due to support and surrounding strata was remarkably reduced, and the face advanced normally.

Jan 1, 1992

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999