Search Documents

The Aredor mine employs conventional dragline methods to exploit alluvial diamond deposits. Production began in 1984 with the policy of mining in the terrraces during the wet season and in the river flats during the dry season. Early production failed to meet predicted grades. A major geological programme to re-evaluate existing reserves was undertaken. This resulted in considerable increases in reserves in the river flats. Many of the reserve blocks included flats on both banks of the Baoule river. Methods of access into the river flats, normally flooded in the wet season, were developed to allow mining throughout the year. River diversions have been the main method used to provide access into the reserve blocks and, most importantly, to remove the risk of flooding. Aredor has carried out six main river diversions with a total length of 12 km. The diversions allowed production planning to be made on the basis of the economic evaluation of the reserve blocks, without undue regard to natural ground conditions or to seasonal factors. The Manning equation was used for the calculation of channel dimensions and gave satisfactory results. The practical aspects of the diversion preparations and flooding prevention are described

Sep 1, 1991

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

By J. L. Carr

Continuous mining machines are extensively used in the underground coal mining industry. These machines are typically remote-controlled, and severe injuries and fatalities occur every year when a miner is struck or pinned by the machine. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Researchers at the National Institute for Occupational Safety and Health (NIOSH)have developed the Intelligent Proximity Detection (iPD) system to provide enhanced protection while minimizing false alarms. The iPD system uses a set of pre-defined rules to determine which machine motions are safe and which would present a potential hazard, and automatically disables only the potentially hazardous motions. This system has been installed and tested on a Joy 14CM continuous mining machine at the NIOSH Office of Mine Safety and Health Research in Pittsburgh. Under laboratory conditions, the achievable accuracy and performance of the iPD system has been quantified with respect to a number of variables including position of the conveyor boom, presence of the machine?s trailing cable, and orientation of the miner-wearable component. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert systems designed for real-time processing plants that also include the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. [1,2] In spite of the fact that significant performance increases have been achieved using these systems they are not perfect and can be improved. They suffer from the static nature of their rules and to a degree the process models. There is an opportunity to further increase system performance by systematically taking advantage of the tremendous amount of data produced by the expert system to improve the design, the heuristic rules, the model topologies and the use of the models. Data mining refers to extracting or mining knowledge from large amounts of data where the objective is to automatically analyze, classify and summarize the data to automatically discover and characterize trends in it and to automatically flag anomalies. [3] Clearly, modern process control systems are capable of collecting vast amounts of data. Without a doubt, these data contain important information on the operation of our plants and their ultimate optimization. Coupling the information mined from these data with Expert Control Systems should produce more effective control and greater knowledge of the grinding process and the flotation process. Now, with the advent of effective monitoring of entire minerals plant electric consumption it is possible to not only optimize plant production in real-time it is possible to analyze total plant electrical consumption and incorporate it into the plant control logic thereby improving the overall plant economic performance. This is particularly important with the ever more complex power contracts that plants operate under.

Jan 1, 2012

By Fabrice Mathieu

The Cutter Soil Mixing (CSM) provides a cost effective solution for the rapid construction of retaining and cut-off walls using new equipment developed from diaphragm wall cutter technology. CSM consists of cutting and mixing drums mounted on compact hydraulic motors. Soletanche Bachy CSM has been designed to leave the space above the tool free, thereby mixing the soil efficiently during all the phases of the wall construction, with high penetration rates. The precise positioning and verticality of the wall is achieved using a kelly bar and full monitoring. Soletanche Bachy CSM is a versatile equipment which can be mounted on various carriers: pile rigs, hydraulic crane, carrier equipped with telescopic mast. The major phases of Soletanche Bachy CSM development are presented, including the results of an extensive trial carried out in Le Havre (France). The soil consists of hydraulic fill with soft soil lenses overlying sandy deposits. 20m deep panels were constructed to support a rectangular shaft. During the construction, and after its completion, the shaft was subjected to an extensive series of tests followed by a partial excavation. The paper discusses also the future development of the technique and its potential applications.

Jan 1, 2006

By D. Boshoff

The ability of an explosive to break rock is influenced considerably by the extent of confinement in the blasthole. It is believed that confinement is improved by the use of adequate stemming. The aim of this paper is to present the results of the first and second stages of developing a stemming performance testing rig for small diameter boreholes. The rig was used to compare and contrast the performance of different designs of products. The results showed that different stemming products have differences in terms of their functionality, which can have a major impact on the efficiency of rock breaking. Two test procedures were used, one through the exclusive use of compressed air and the second using a purpose-built high pressure test rig with small quantities of explosives. Both tests were used to identify and evaluate the ability of various stemming products to resist the escape of explosive gas through the collar of a blasthole. An investigation was done to determine the types of stemming products most commonly used in South African underground hard rock mines, and these products were used during the tests. The first stage of tests using compressed air only did not prove adequate to predict with certainty the pressure behaviour in the borehole of a particular product under high pressure conditions. The purpose-built high pressure test rig also did not prove to be a very effective tool to test stemming products under high pressure conditions. The test rig incorporated only the effect of gas pressure on the stemming product, and excluded the effect of the shock wave. This study therefore proved that to take into account only the gas pressure generated in the blasthole is not sufficient to effectively test stemming product performance.

Jan 1, 2011

By H. S. Kennedy

THE HELIUM ACT (50 Stat. 885; 50 U. S. C. 161,163-166), as amended, places the responsibility for conserving, producing, and selling helium upon the Secretary of the Interior, acting through the Bureau of Mines-the only producer of helium in quantity in the world. It operates 4 plants-I each at Amarillo and Exell, Tex.; Otis, Kans.; and Navajo (Shiprock), N. Mex. The demand for helium has increased steadily since the decline immediately after World War II and is expected to exceed the capacity of the present plants in the near future. The Congress has appropriated $6,000,000 far constructing a new plant. In addition to providing additional capacity to meet increased demands for helium, the new plant will enable the Bureau of Mines to better conserve the helium in, the Government-owned reserves at Amarillo and Navajo.

Jan 1, 1958

It is well known that the electrochemical precipitation of metals from aqueous solutions is conducted by the electrochemical standard potential scale. This scale indicates the order of nobility of different metals. Consequently, the standard potential scale shows the nocivity of metals when they are present as impurities in aqueous solutions containing metals. In the hydrometallurgy of cobalt, nickel and zinc are co-deposited during cobalt electrodeposition. Nickel has almost the same chemical, physical and electro-chemical properties as cobalt. Furthermore, the electrochemical potential of nickel is relatively higher than that of cobalt. For this reason nickel is preferentially reduced at the cathode in the presence of cobalt. The presence of small amounts of zinc in solution leads to contamination of cobalt electrowon. In spite of its lower electrochemical potential in comparison to cobalt, zinc is reduced on the cathode because of its higher hydrogen-overvoltage. But, in the hydrometallurgy of zinc, small amounts of cobalt present solution will contaminate the zinc reduced at the cathode. This is easily explained by the fact that cobalt is more electropositive than zinc. The co-deposition mechanism of sulphur at the cathode is not yet well understood. Great attention has to be paid to the mechanism of co-deposition of sulphur during cobalt electrolysis. This work aimed to investigate the influence of some parameters on the co-deposition of nickel, zinc and sulphur during cobalt electrowinning. The following parameters have been investigated: Co2+concentration in the electrolyte, current density and ammonium sulphate (NH4)2SO4additions. It has been established that important nickel, zinc and sulphur co-deposition takes place at relatively low Co2+ concentration in solution. The behaviour of these elements with regard to the cathodic phenomena has been established.

Jan 1, 2005

By J. Nakayama

For drilling large diameter holes for deep foundations, the common and distressing difficulty of long standing has been in coping with ground containing rocky formations and boulders. Where geological formation contains weathered rock or boulders, or deep rock socket is specified, drilling equipment occasionally is found to be unable to drill through and therefore will need supplementary equipment and procedures. Incentive of the MACH Drill Development has been to realize a capable drilling system for rocks of weathered to fresh rock without losing its applicability to usual overburden. Through seven decades' experience of manufacturing and operation of boring machines, the best features of all sorts of drillhead are known such as the drag bit, wing bit, auger bit, diamond bit, rock roller bit, down-the-hole hammer bit, etc.

Jan 1, 1988

By Elizabeth Gardiner

Tailings and water management facilities are integral components of mine and mill operations. They must be managed for the long term to ensure that safe and environmentally responsible stewardship is achieved. The Mining Association of Canada (MAC) has developed and published two manuals to provide guidance to mining companies on sound practices for the safe and environmentally responsible management of tailings facilities: ???A Guide to the Management of Tailings Facilities; and ???Developing an Operation, Maintenance and Surveillance Manual for Tailings and Water Management Facilities. The Guides were designed to help companies develop and implement tailings management systems that include environmental and safety criteria, to improve the consistency of application of sound engineering and management principles to tailings and water management facilities through their full life cycle, and to demonstrate this to regulators and the public.

May 1, 2003

By B. Roy

The Somita plant processes low sulphide gold ore in Burkina Faso with a CIL process. After experiencing recurrent low gold recoveries, Somita undertook an investigation on the source of the problem. COREM conducted a mineralogical study on different pit samples. A series of tests was also conducted on a composite sample from the plant which shows a content of 3.4 g/t in gold and 0.48 % in graphite. A reference test in laboratory resulted in a recovery of gold of 75%, similar to plant recoveries for the evaluated ore. In these tests, even if cyanide is not deficient, it was diverted mainly into iron cyanide complex, copper cyanide complexes and by graphite adsorption. Causes of low recovery were also identified and quantified. Solutions to increase gold recovery were suggested such as increasing gold dissolution kinetics by O2 or by lead nitrate addition, change in activated carbon addition point location to the 1st cyanidation tank and finer grinding to increase liberation. Increase in the pH could also contribute to reduce cyanidation consumption. Following these recommendations, Somita changed carbon addition from tank 2 to tank 1 in the CIL circuit. This change led to an increase of more than 5% in gold recovery. A system for the addition of lead nitrate is also under implementation at the plant and benefit will be evaluated in 2013. Finally, pit management for cyanidation will be done based on mineralogy instead of gold content in the future.

Jan 1, 2014

By Siavoljub D. Maksimovic

The Bureau of Mines, through a cooperative agreement with Duquesne Light Co. of Pennsylvania, field tested a method of using pneumatic stowing of crushed limestone to construct seals in long-abandoned mine openings that were part of an active mine closed shortly before sealing. A total of 13 openings at 11 sites were backfilled. In pneumatic stowing, material is conveyed through a pipeline and into the mine opening under low air pressure. The stowing equipment consists of a power sup-ply, a blower, a feeder to inject material into the pipeline, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. The fill material used was well-graded limestone aggregate up to 1-1/2 inches in diameter, with sufficient fines. This fill was modified at five locations by the addition of portland cement, expansive cement, and/or bentonite. The pneumatic stowing method is safer and faster than conventional methods, is cost competitive, and eliminates or reduces the exposure of workers to possible hazards since the nozzle can be kept outside the mine opening. The equipment is mobile, but some modifications in the technique would improve performance. The technique was used at remote locations where other methods could not be used without disturbing the environment.

Jan 1, 1982

By P. N. Vernon

Ausmelt top entry submerged lance technology offers a cost-effective means of carrying out a range of base metal smelting operations with minimum impact on the environment. The system is capable of using a range of fuels depending upon local costs. Due to the intense, localised reaction zone, high energy efficiency is obtained and the physical size of the plant is relatively small compared to that of most competing technologies. Capital cost can thereby be minimised. The furnace is well enclosed, such that fugitive emissions and ingress of diluting air to the gas stream are both minimised. The oxygen potential in the slag can be varied over a wide range such that the system can be applied in both oxidising and reducing duties. Following a general description of the technology, the paper discusses Ausmelt plants already in operation. The application of the technology for the provision of additional smelting capacity, for the improvement of converting operations and for slag cleaning is then described. A brief explanation of how these processes could be applied at southern African smelters is given and the paper closes with an assessment of novel Ausmelt applications for this geographical region, such as zinc recovery from sulphides.

Jan 1, 1997

By James Westfield

Bureau of Mines activities for safety and health in the mineral industries were reorganized during the fiscal year to provide direct supervision by the Assistant Director -Health and Safety. On December 19, 1954, the field offices conducting these activities were designated as district health and safety offices reporting to the Assistant Director. The functions of determining the causes of accidents and injuries in the mineral industries and recommending measures to eliminate them were continued, with satisfactory results in improved safety records. The inspection of coal mines and enforcement of the Federal Coal Mine Safety Act of 1952 were conducted as directed by the Congress, and safety conditions in the mines were notably improved. One coal-mine explosion classed as a major disaster occurred during the year. The causes of that explosion and means for preventing a recurrence were still under investigation because of the extreme difficulty in recovering several portions of the mine. Basic research on the nature of certain hazards and ways of eliminating them is continued. Training of individual workmen and supervisors in this knowledge is a major part of the work.

Jan 1, 1956

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By H. J. Heinen

This Bureau of Mines report reviews the recent developments in the heap leaching of gold ores with dilute cyanide solutions and the recovery of gold and associated silver from the pregnant effluents by a carbon adsorption-desorption method. Mineralogical considerations, experimental work, field studies, and commercial operations are described. Also presented are recent process advances developed by the Bureau, including the application of (1) alcohol additives to the conventional hot alkaline cyanide strip solution to enhance gold desorption from precious metal-laden activated carbon, and (2) Na2S precipitation of the silver from geld-silver cyanide solutions as a means of reducing the inventory of carbon required for precious-metal adsorption from heap leach effluents and for the production of low-silver bullion from activated carbon stripping solutions.

Jan 1, 1978

By G. S. Harper

Noise in general and drilling noise in particular have received increasing attention within the South African mining industry during the last 10?15 years. The Mine Health and Safety Committee1, during their 2003 annual summit, established two significant milestones to be met by December 2008 and December 2013. The 2008 milestone target is that of no more than ten per cent deterioration in hearing among occupationally exposed individuals, whereas the 2013 milestone target is that of less than 110 dB sound pressure levels at any place in the workplace. While these targets relate to general noise within the mining industry, it is widely believed that the most significant source of noise contributing to noise induced hearing loss (NIHL) among the underground workforce, is that of pneumatic rock drills. Data pertaining to the noise emission level of any machine is generally reported as either a sound pressure level or a sound power level of a single machine measured under free field conditions as defined in Appendix 3 of SABS-ISO 37442. However, rock drills are seldom used in isolation and underground conditions cannot be considered as free field. A methodology for the selection of rock drills on the basis of total operating cost has been developed. However, this paper focuses on the noise elements of the generic methodology and provides a model for the prediction of the composite sound pressure level and the equivalent noise exposure levels of groups of individuals from machines, used singly and in combination in an underground environment based on the sound pressure level determined according to SABS-ISO 3744 under free field conditions. The methodology includes provision for the consideration of the effect of hearing protection devices and the use of multiple machines in combination and provides an indication of the potential costs of hearing compensation.

Jan 1, 2006

By H Möller

The purpose of this paper is to give an overview of the corrosion behaviour of steel in seawater. It is shown that the corrosion products (oxy-hydroxides and calcareous deposits) that are formed during corrosion in seawater have a significant effect on the corrosion behaviour of steel. The chemical composition of the steel determines how protective the oxy-hydroxide corrosion product is. The composition of the seawater influences the nature of the calcareous deposits. This needs to be considered when artificial solutions are used to simulate the corrosion behaviour of steel in seawater. A 3.5% NaCl solution is used frequently for this purpose, but because no calcareous deposits can be formed in this solution, erroneous results in terms of corrosion rates are obtained. The more complex ASTM D1141 artificial solution can be used to include the effects of ions other than Na+ and Cl- in synthetic seawaters. The importance of these other ions on the formation of calcareous deposits is discussed. Keywords: Steel, corrosion, seawater, calcareous deposits, oxy-hydroxides

Jan 1, 2006

By S. A. G. Poppen, M. B. Mirza, A. I. Cooley

The U.S. Department of Energy (DOE) is responsible for siting and constructing a licensed geologic repository for commercially generated high-level nuclear waste. Within DOE, the Office of Civilian Radioactive Waste Management (OCRWM) Program has this responsibility. To accomplish this mission, the OCRWM Program is engaged in a multidisciplined effort to identify, qualify, and develop repository sites. The current strategy of the OCRWM Program is to identify candidate repository sites in basalt, tuff, and salt and to develop exploratory shafts at those sites. Within OCRWM, the Salt Repository Project Office (SRPO) identified the salt site for the development of exploratory shafts. The proposed Exploratory Shaft Facility (ESF) in salt will have several primary purposes. The shafts will provide access to the reference repository horizon to permit in situ testing of the salt horizons in order to satisfy the following data acquisition needs: • Verification of the salt repository design parameters and validation of performance assessment models • Demonstration of the constructibility • Capability to adequately seal penetrations into the salt An exploratory shaft is required by 10 CFR Part 60 for the conduct of in situ testing at depth prior to submittal of a license application for construction authorization of a repository. Therefore, construction of an ESF will also facilitate the licensing process.

Jan 1, 1987