Search Documents

By S. J. Jung

A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.

Jan 1, 1989

The principal activities of the Bureau of Mines Explosives Research Center during fiscal year 1967 (July 1, 1966, to June 30, 1967) arc reviewed in a part 1. Part 2 presents short abstracts of the publications issued during this period in the Bureau series and in other media. Part 3 describes a short study on the shock initiation of hydrogen peroxide not destined for publication elsewhere. ACKNOWLEDGMENTS The Bureau of Mines gratefully acknowledges the support received through cooperative agreement in fiscal year 1967 from The Dow Chemical Company Manufacturing Chemists' Association, Inc.

Jan 1, 1968

By E. Ringdalen

Keywords: Pyrometallurgy, research, Norway, SINTEF, NTNU The Norwegian Ferro-alloy Industry and the model for research cooperation between SINTEF, NTNU, and the Norwegian ferro-alloy industry is presented as an introduction. The research within pyrometallurgy is illustrated by examples from characterisation of Mn-ores and characterisation of carbon materials. Examples from studies of reaction mechanisms in laboratory- and pilot-scale experiments are presented, in addition to an example of industrial off-gas measurements. Education possibilities at NTNU are also described.

Jan 1, 2011

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, and control of anthracite-mine fires, it was observed that the carbon monoxide disappeared from a sealed fire area much more rapidly than could be explained on the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance: (1) That the carbon monoxide, was oxidized at temperatures below 150° C. by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C. carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By B. Arjang

ABSTRACT: Ground stresses are one of the significant factors in the context of rockbursts and underground instability at some hard rock mines in Canada. Overcoring strain relief measurements using triaxiaI strain eel is were performed at depths between 60 to 1890 m at several mine sites to provide stress data for stability analysis and optimum mine design. Pre-mining ground stress determinations from 64 stress tensor analyses resulted in the following average stress gradients: Maximum horizontal stress. -Hmax - 8.18 - 0.0122 MPa/m depth Minimum horizontal stress. _-,,min - 3.64 - 0.0276 MPa/m depth Average horizontal stress. -11, 5.91 - 0.03-19 MPs m depth Vertical stress. '-, - 0.0266 - 0.008 MPa/m depth The maximum and minimum horizontal compressive stresses. with an average ratio of 1.75 ,0..45. prevail in east--west and northerly directions. respectively. Horizontal compressive stresses in excess of vertical overburden load were determined. indicating large variations in ratios to a depth of about 1000 m with decreasing trend towards depth. From present data. a particular regional zoning for the magnitude and direction of horizontal stress fields cannot be outlined. A common feature at mines with near vertical orebodies is that the maximum horizontal compressive stress acts perpendicular to strike while the minimum horizontal compressive stress is aligned on-strike. The vertical stress components approach the gravitational overburden load.

Jan 1, 1989

By Prasenjit Basu

Drilled displacement piles are being increasingly used as foundation elements, particularly in projects requiring fast construction. Different types of drilled displacement (DD) piles are available in practice. DD piles are classified according to the drilling tool design and installation method. The capacity of a DD pile, depending on its type, is between the capacities of geometrically similar nondisplacement and full-displacement piles installed in the same soil profile. This paper provides an overview of the different types of DD piles and their installation techniques and describes three design methods used in practice. It also compares DD pile capacities obtained with these design methods for two different sites.

Jan 1, 2010

By Dave Bulled, Jim Thompson, Tim Leriche, Mark Blake, Troy Wilkie

"A commitment to a core testing, plant modeling and reconciling technique has shown substantial economic benefits to IOC in terms of accurate production forecasting, smoother operation of the mill, improved expectations of throughput and co-operation across production departments from geology, planning, mining, and processing, to shipping of concentrate to market.This paper describes a successful seven year program of forecasting throughput of the autogenous milling circuit at the Carol Lake concentrator of IOC. Work started with audits of the grinding circuit in 2001 and benchmarking of the data collected from samples of mill feed and plant operation to the CEET mill design and throughput forecasting model.Initially 390 drill core samples were tested for SAG Power Index (SPI) to measure the energy required in milling, and the data distributed using a geostatistical technique across the two operating pits, so that hardness was estimated in each of the 40,000 blocks (or 1500 million tons) of potential ore. In 2004 a forecast of energy requirement, i.e. forecast of throughput for a given power availability at the mill, was produced for each ore block using the CEET model and used for mine planning to smooth plant throughput. The forecast for blocks mined on a monthly basis was reconciled with plant results over the next 2 years and minor changes made to the CEET model. The forecasting exercise was repeated in 2006 and in 2008 with the latest model based on the testing of almost 1300 samples of drill core at closer spacing.INTRODUCTIONThe contracting of sales to clients and the timely supply of products to meet those contracts is a cornerstone of good business practice. Ensuring the correct scheduling of production is a major concern of mining companies where the supply and qualities of the raw material is uncertain and production facilities are not flexible. This is particularly challenging when the product is of high volume and produced far from the customer, such as iron ore.Apart from the metal content of the ore being mined, the greatest impact on production scheduling is the throughput of the comminution section of the extraction plant; most notably when size reduction is achieved by autogenous grinding. The response of the mills to variability in the hardness of the ore can change throughput by as much as 50% from day to day at some plants."

Jan 1, 2009

By S. P. Ball, A. J. Monhemius

In a laboratory study under acidic oxidising conditions, the thiocyanate system gave results at least as good as cyanide and considerably better than thiourea, with modest consumption of SCN (less than 1 kg/t ore). For both cyanide and thiocyanate lixiviants a residence time of about 24 h was required for maximum gold extraction, which was generally in the range of 92-96%. The adsorption of gold from thiocyanate leach liquors was found to be rapid, but activated carbon catalyses the autoreduction of ferric iron to ferrous iron in thiocyanate solutions, suggesting that ion exchange may be a better recovery route

Dec 1, 1995

Effective Dry Density Benefication of Coal

Sep 13, 2010

By Xie Qiang

It is known that the stress state inside rock discs under Brazilian tests is neither simple compression nor tension, but a complex combination of both stress types, as well as for a beam subjected to bending, where compressive and tensile stresses are separated by the neutral axis. In this study, AE generation was obtained on pure white marbles from south Portugal that were submitted to both Brazilian and bending tests. Main questions to be answered were: (1) Does Kaiser effect exist in tests which create complex distributions of tension and compression? (2) Are there any meaningful differences in AE behavior of marble under Brazilian and bending tests?

May 1, 2009

By C J. Hogan

Increasing demand for fine grinding to improve mineral liberation and metal recovery and the need for stricter control of the environmental impact of tailings deposition poses problems for tailings disposal. This has led to an increasing number of investigations of properties of tailings and their disposal. This paper describes laboratory model testing undertaken on Macraes mine flotation tailings to provide information on tailings behaviour under conditions of subaerial deposition. The in-place density or 'dry density' of the impounded tailings and the impoundment depth relationship are important for utilisation of the available impoundment storage facility and results of dry density to depth relationships are given for the Macraes mine tailings impoundment.

Jan 1, 1993

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common- wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables 'were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1978

By Frank Rausche

Without doubt, driven piles are the most economical deep foundation element for a nearshore environment, providing for high bearing capacities and stiffness, quick installation times, assured quality by simple monitoring and inexpensive dynamic load testing during restrike testing. However, when the pile top elevation is several meters below water surface, questions often arise as to the most reliable and economical pile installation method. Frequently encountered, yet relatively expensive, solutions include driving inside a dewatered cofferdam, driving long piles that are later cut off below water surface, or using an underwater hammer. Arguably, the most economical solution is driving the piles with a follower or chaser. However, many foundation engineers shy away from this solution because of the uncertainty associated with the transfer of energy through the interface between follower and pile, the associated potential driveability problems and maybe the limited fatigue life of the follower. This paper will demonstrate how the driveability of a hammer-follower-pile-soil system should be analyzed prior to installation and how to model the pile-follower interface both for steel and concrete piles. As an example, results will be presented which were obtained for both steel pipe piles and precast concrete piles, driven by a single-acting diesel hammer through a steel follower for a pre-construction test pile program in Venice, Italy. While analysis of the steel pile-follower system was straightforward, for the concrete piles, the presence of a soft cushion material whose material properties changed continuously posed some difficulty. Pile Driving Analyzer® measurements and CAPWAP® analysis yielded not only realistic stresses and transferred energy values in the pile, but also reasonable model parameters for further use in a pure wave equation analysis. As a side note for clarity, the dynamic measurements and analysis results herein presented are based on the GRLWEAP and CAPWAP software. GRLWEAP is commonly used all around the world for the preparation of pile driving jobs. The program either yields a bearing graph that relates bearing capacity and pile stresses to blow count or set per blow or it predicts blow counts and pile stresses as a function of pile penetration. These results allow the contractor to estimate driving time and select an economical hammer and driving system for a safe and efficient installation. CAPWAP on the other hand is the analysis of choice once a pile has been installed and records of pile top force and velocity have been acquired during installation or during a restrike test. CAPWAP is a signal matching program which calculates for one particular impact (for example at the end of driving) the static and dynamic soil parameters. Its final results include the calculated resistance distribution, the complete stress history in the pile and also a simulated load set curve. The CAPWAP calculated dynamic soil parameters can also be used in a Refined GRLWEAP analysis to generate a calibrated bearing graph."

Jan 1, 2006

A comprehensive axial test program has been undertaken at the WASM Dynamic Test Facility on the performance of 20mm threadbar. The threadbar tests had a double embedment configuration, with variation to the encapsulation lengths, debonded length and surface hardware and fixtures to examine failure mechanisms. Performance was significantly affected by the collar embedment length and type of fixture nut used. Results ranged from thread shearing occurring between the nut and bar at 1kJ of energy dissipated, to control plastic deformation of a central debonded length dissipating 22kJ.

May 1, 2009

By Derek Ettie

"In the Hydrometallurgical processes, the presence of the so-called "crud" is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design.The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the series-connected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation.The transfer of the organic phase into the electrolysis cell can result in a "burnout" of the cathode. The carryover of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show.To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl® by this means, we can guarantee our customers the maximum possible solvent recovery and minimize the solvent costs in this process step. This system is presented in detail in this paper."

Jan 1, 2014

By K. Blaski

his paper reports an investigation aimed at optimizing the compaction of granulated hard-metal powder for the production of cutting tool inserts. The optimal compaction is that which yields optimal shrinkage during sintering, i.e. minimum porosity in the sintered part. Extensive compaction tests on 23 different hard-metal powders have been carried out and have shown that the ideal ?green density? of a hard-metal compact, i.e. the density after compaction, increases linearly with the apparent density of the powder. On the basis of this result, an equation has been derived, which allows one to predict the optimal shrinkage that a hard-metal compact undergoes during sintering once the following data are known: the required sintered density, the volatile content of the powder and the apparent density of the powder. Since these data are available to the tooling designer, this equation allows one to design tooling for the compaction of hard-metal, which leads to optimal shrinkage

Jan 1, 2007

By Richard Havens

Acidic and basic uranium leach plant residues located on the Navajo Indian Reservation, Tuba City, Ariz., were successfully stabilized against wind erosion using a relatively low-cost chemical method. An elastomeric polymer chemical was applied to the dike areas and a calcium magnesium lignosulfonate to the beach areas of three tailings ponds. The water-soluble chemicals were applied with an automated sprinkling system. The stabilization cost was $335 per acre for the 34.5-acre tract.

Jan 1, 1969

By Vilma Beltrán

Dado que los trabajos de procesamiento metalúrgico de la mina Uchucchahua, ocasionaron impactos en el medio ambiente, afectando la calidad del agua y eliminando la vida acuática en las lagunas Añilcocha, Colquicocha y Tinquicocha, se procedió a encontrar una alternativa de tratamiento biológico que recupere la calidad de vida en la mina Uchucchacua. En este sentido, el presente trabajo describe el tratamiento pasivo de los efluentes con manganeso de la mina Uchucchacua. Para dicho procedimiento, se desarrollaron trabajos en dos etapas: el de laboratorio y balde. El primero comprende los sistemas de tratamiento pasivo anaeróbico y aeróbico.El aeróbico se inició sobre la base de los procesos de filtración y aireación a fin de determinar el grado de oxidación y precipitación del manganeso como óxido, mientras que el segundo se realizó en función a los resultados obtenidos en la etapa laboratorio y comprende los siguientes procesos: filtración, autooxidación, aireación, sedimentación. En consecuencia, los procesos anaeróbicos no favorecen la reducción de Mn II en los efluentes estudiados, mientras que los procesos aeróbicos permitieron la disminución del manganeso.

Sep 13, 2001

By Manis Kumar Jha

Leaching studies were carried out for the recovery/ recycling of metals from PCBs containing 17.05% Cu, 0.74% Ni, 1.74% Fe, 4.35% Pb and 8.32% Sn using various acids such as H2SO4, HCl and HNO3. While sulfuric acid was not a suitable leachant for the dissolution of metals from PCBs, hydrochloric acid selectively dissolved tin. The nitric acid was found to be effective lixiviant with the recovery of 99.99% Cu, Fe, Ni and 36.7% Pb in 6M HNO3 at S/L ratio of 100 g/L and 90oC. The kinetic studies carried out with 2M and 4M HNO3 at 90oC showed ?Ash diffusion control dense constant size-spherical particles? model.

Jan 1, 2010

By E. P. Ferrero

Crude oils from fields throughout the world are analyzed by the Bureau of Mines to determine the characteristics of the oils and their contribution to the petroleum resources of the world. Analyses are reported for 169 foreign crude oil samples from 122 oilfields in Africa, Asia, Australia, the Caribbean, Europe, North America, and South America. Tables show the geographic and geo- logic origin of the samples, names of companies that supplied the samples, annual production for the fields, general characteristics and analytical and computed data, hydrocarbon-type data, cumulative production of the larger fields, and references to sources of geological and field development information. The analyses were made by the Bureau of Mines routine method and comparisons may be made with more than 8,000 other such analyses.

Jan 1, 1972