Search Documents

By Gary A. Kingston

Low-cost hydroelectric energy in the Pacific Nortnwest has been an important factor in the development of a ferroalloy industry. Eleven companies, employing approximately 1,000 persons, produce about 116,000 tons (1954-58 average) annually of ferrosilicon, ferrochromium, ferromanganese, ferrophosphorus, silicomanganese, and ferronickel. About 7,500 tons (1954-58 average) of these ferroalloys is consumed in the Pacific Northwest States of Washington and Oregon; the rest is used principally in other western and mid-western markets. In 1959, the Bureau of Mines began a study to determine the current status and to evaluate the potential of the ferroalloy industry in the Pacific Northwest. The Bureau gathered information from operating alloy plants in Oregon, Washington, Idaho, and Montana; from published materials; and from consumers of ferroalloys.

Jan 1, 1962

By J. H. Holden

Operations involving the processing of coal, oxygen, and steam into synthesis gas by means of two pressure-type gasifiers have demonstrated the effect of heat loss and operating variables on carbon gasified and oxygen and coal requirements. Carbon gasified is the fraction of carbon in the coal that is converted to gas. Oxygen and coal requirement is the quantity of each that is needed to produce a unit volume (M std. c.f.) of carbon monoxide and hydrogen. Operating pressure of the gasifiers ranged from 150 to 300 p.s.i.g. and coal was fed at 200 to 500 lb./hr./cu.ft. of reaction-zone space. Oxygen-to-coal ratios were 8.5 to 10.5 std. c.f./lb. Heat loss and residence time have opposite effects on carbon gasified; increasing the heat loss decreases the carbon gasified, but increasing the residence time (by raising the operating pressure or reducing the coal-feed rate) increases the carbon gasified. The effects of these two factors are difficult to separate because they usually change simultaneously. A comparison of the results obtained from the operation of two gasifiers with different levels of heat loss, however, permitted the effect of heat loss to be separated from that of pressure and coal-feed rate. When the results were deter- mined on the basis of constant heat loss, increase of the residence time increased the carbon gasified until the reaction virtually had come to completion. For example, at 150 p.s.i.g., decreasing the coal-feed ratio from 500 lb./hr./cu.ft. to 200 lb./hr./cu.ft. substantially increased the carbon gasified. At 300 p.s.i.g., however, changing the coal-feed rate had little effect on the carbon gasified because the reaction had almost reached completion and further increase in residence time resulted only in a negligible change.

Jan 1, 1962

By T. M. Barczak

Stoppings are required to resist lateral forces on the face of the structure to control pressure differentials created by ventilating air. The design criteria in other parts of the world, including Australia, exceed this requirement by specifying over pressurization control to as much as 14 kPa (2 psi) in the active sections and 35 kPa (5 psi) in the main ventilating control areas. This is done to provide protection to the mine workers from explosive or air blast events within the mine that can create this over pressurization. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research to develop a new testing protocol for rating mine ventilation stoppings. The premise of this work is that arch-loading conditions more accurately reflects the transverse load capabilities of stoppings in underground coal mines than the freestanding flexural strength test specified in the current Code of Federal Regulations (CFR). This work clearly shows that the transverse load capabilities of dry-stacked, mine ventilation stoppings are dependent upon the material strength of the block and the height and thickness of the wall, none of which are part of the current CFR criteria based on ASTM E-72 specifications. This paper compares the transverse load capabilities of several block materials and wall dimensions commonly used in stopping constructions based upon simulated three-hinge, rigid-arch loading tests of half-wall constructions in the NIOSH Mine Roof Simulator. The results indicate a wide-range of transverse load capacities, ranging from as low as 21 kPa (0.3 psi) to as much as 117 kPa (17 psi) for the conditions evaluated in this study. The current CFR criteria do not distinguish between applications of these stopping designs despite their wide variance in transverse load capabilities, which is not conducive to employing ventilation control strategies that isolate certain sections of the mine to prevent injury to mine workers.

Jan 1, 2009

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By S. J. S. Ferreira

Anglo American Platinum's Khomanani 2 shaft changed over from down-dip mining to breast mining in 2004. The changeover was made to ensure that production targets were met, as it was said that predevelopment for down-dip mining was not fast enough to sustain the required ore reserves; nevertheless, production performance did not increase as expected. In this study a trade-off was performed between down-dip mining and breast mining on the Merensky Reef at Khomanani 2 in order to find the most suitable method for mining the Merensky Reef. Data was gathered by means of a literature survey, underground observations, and interviews with personnel as well as data from various departments on the mine. The two mining methods were studied and then evaluated in terms of the following criteria: safety, mining rate, cost and other factors which were identified as the main drivers of the mine. A scaling system was used to rate the performance of the two mining methods. Analysis of the results shows that down-dip mining and breast mining have the same safety performance ratings. Breast mining has a better mining rate performance than down-dip mining. Breast mining was found to be costly in comparison with down-dip mining, which has a good cost performance rating. The overall ratings of the two mining methods are very similar, with down-dip mining achieving a rating of 76 and breast mining 75.5 out of an optimum 102. Khomanani 2 currently practices breast mining, and with such a slight difference in performance rating between the two methods, it will not be worth changing over to down-dip mining as production is likely to be adversely affected during the changeover. Down-dip mining does, however, have potential for improvement in its performance rating. Further studies focusing on the improvement of the mining rate performance for down-dip mining are needed to see if this potential can be realized. If significant improvement can be made in the performance rating for down-dip mining, a changeover to down-dip mining can be reconsidered.

Jan 1, 2012

By R. Codell, D. L. Hughson

While benchmarking the integrated finite-volume code MULTIFLO against the analytical solution of Philip et al. (1989) for cylindrical underground openings, we found numerical simulation of dripping threshold flux consistently higher than the analytical solution for both rectangular and unstructured grids. The magnitude of error is proportional to the alpha parameter characterizing capillarity. This may bias estimates of repository performance towards non-conservatism.

Jan 1, 2000

By M. A. Meyer

Underground mining accidents in the USA in recent times have prompted the Mine Safety and Health Administration (MSHA) to review emergency and tracking systems for underground mines. Several communication and tracking systems are available on the market and various systems have been installed in mines around the world. In addition, MSHA?s standard on Diesel Particulate Matter (DPM) requires mines to comply with the final PEL of 160µg/m3 by May 20, 2008. Barrick Goldstrike Mines Inc., Underground Division, has been in operation since 1995 and an extensive control and monitoring network, and a leaky feeder voice network is in place. Enhancements to the communication and control system are currently being implemented to include a PED emergency notification system, wireless LAN with tracking of personnel and equipment in the mine, and a ventilation control system that will use the tracking information and ventilation data to automate much of the mine ventilation system. Expected benefits from such a system would be enhanced communication with miners, emergency notification, location of miners and equipment, energy savings, improved ventilation control, and improved atmospheric conditions in the mine including reduction of diesel particulate matter (DPM).

Jan 1, 2009

By S. Lolon

Spontaneous combustion in underground coal mines has become a serious problem particularly in the caved area (gob). Recent statistic has shown that approximately 17% of total 87 underground coal mine fires in the United States are attributed to spontaneous combustion (De Rosa, 2004). Spontaneous combustion results from a self-heating process in exothermic conditions. The accumulated heat, if not removed, is conducive to the rapid increase of temperature and may result in mine fires or explosions. It is well accepted that the interaction between oxygen and coal substances is the main cause for spontaneous combustion, while other factors such as pyrite, moisture, and bacteria play a secondary role to the self-heating of coal. Therefore, only coal oxidation is considered in this study. Coal oxidation occurs as coal comes into contact with air. This process involves complex phenomena in terms of heat transfer, chemical surface absorption, and energy balance related to inherent properties of coal (Wang et al., 2003). For simulation purpose, overall reactions can be simplified as suggested by Mitchell (1990): C + O2 CO2 + heat [65°- 94°C] (1) CO2 + C 2CO + heat [100°- 150°C] (2) Stoichiometric reactions (1) and (2) show that 2.66 grams of oxygen are required to oxidize 1.0 gram of carbon. Once the temperature exceeds 100°C, the reaction has little chance to stop. The crucial step in reducing spontaneous combustion risk is locating the ignition point of spontaneous combustion (hot spot). This information is useful in the effort of developing a preventive method effectively. In this study, this was conducted based on the best gathered information: ventilation surveys conducted in an existing longwall mine located in the western US; the laboratory experiments performed on a physical gob model; and the CFD models to investigate the flow behavior in the gob, the oxidation of coal, and heat transfer phenomena. The hot spot location is determined as a function of oxygen concentration and gob temperature. The critical values are the following: 5% (by volume) for oxygen and 100°C for gob temperature. CHARACTERISTICS OF GOB MATERIAL AND MODELS Permeability Concept Permeability is one of the key parameters in any study dealing with porous medium. This is determined by particle size and the ratio of void volume to the total volume (porosity) of porous medium. This relationship is known as the Carman-Kozeny equation (Scheidegger, 1957) and is given mathematically as [ ] where k* = theoretical specific permeability, m2 dm = the mean particle size, m n = porosity However, permeability tests with various particle sizes were carried out at the University of Utah?s ventilation model (Figure 1) to verify this relationship. These tests indicated a necessity to modify this theoretical relationship. A factor of 0.898 was obtained to make up the different between theoretical permeability and the experimental one. The modified version of (3) is given by: [ ] This equation is used to determine permeability of the simulated mine gob throughout the study. [ ] Mine Gob Material The gob is represented by zones filled with material of given size distribution. For physical measurements and CFD simulations, the material used were crushed rock and coal. Due to compaction, three different characteristics of gob material were used in the model: unconsolidated, semiconsolidated, and consolidated. In the real condition, the largest coal-rock particles are more likely to be located in the area behind the shields. This material is freshly broken and unconsolidated. The size of these broken particles is based on a study carried out by analyzing images taken from the area behind the shields in three coal mines in the United States (Pappas and Mark, 1993). The results have shown that the mean size of materials behind the shields is about 1.22 m. The permeability associated with this size was then obtained from (4) and permeability tests. This was 4.68 x10-7 m2. For semiconsolidated and consolidated zones, due to the lack of experimental data, these were determined through CFD simulations. These simulations were designed by assigning a permeability of 3.15 x 10-8 m2 for consolidated zone and 7.98 x 10-9 m2 to the other zone. The airflow pattern in the gob assigned with given permeabilities was expected to follow the experimental distribution (Brunner, 1985). The mean particle sizes for the semi-consolidated and consolidated zones were 0.02 and 0.006 m, respectively; smaller than those of the unconsolidated zone. Figure 2 shows the 3D view of permeability changes in the gob.

Jan 1, 2009

By T F. McConachy, B I. A McInnes, R A. Binns

Within the last decade, major research discoveries have been made in the submarine realm of magmatic and hydrothermal activity of arc-backarc systems in the southwestern Pacific. These include identification of numerous particulate-poor, gas-rich (CO2-CH4) hydrothermal plumes emanating from arc front volcanoes, actively forming porphyry-copper-gold style mineralisation, and new backarc spreading systems erupting alkali basalt-trachyandesite magmas. Major goals of these studies have been identification of modern analogs to ancient volcanogenic massive sulfide ore bodies, and quantification of the volatile fluxes though supra-subduction zone systems.

Jan 1, 2002

By A. H. Swart

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths (resulting in excessive stope spans) that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hardrock mines, shallow mining operations

Jan 1, 2005

By Geir Martin Haarberg

Modern electrolysis technologies can provide possibilities for developing sustainable processes in terms of energy and environment. Laboratory experiments were carried out to study electrodeposition of iron from molten salts and aqueous solutions using an inert oxygen evolving anode to eliminate the emissions of CO2. The possibilities of molten salt electrorefining of metallurgical grade silicon to produce solar grade silicon were also investigated. Electrochemical techniques were used to study the electrochemical behaviour of dissolved iron, silicon, and titanium species. Bulk electrolysis was carried out to deposit pure iron, silicon, and titanium. The quality of the deposits was studied by SEM/EDS and XRD analyses. Calculations based on laboratory studies indicate that great improvements in terms of reduced energy consum

Jan 1, 2010

By Robert Harris, David Duncan

The Samira Hill gold mine represents the first commercial gold project for the landlocked country of Niger in West Africa. It began production in October 2004 as the result of over 10 years of exploration and development work. There were several administrative, social and technical challenges that had to be overcome to realize the successful development of the project. The Samira mine is located on the geological structure known as the ‘Samira Horizon’ which is developing as a promising district for additional discoveries and other mine developments.

Jan 1, 2005

A way back in 1851-2 an army of diggers had commenced the conquest, of the now famous goldfields of Australasia. At that time, and in the Colony of Victoria, more that 10,000 were camped on and around the slopes of the silurian ridges over which Ballarat East h'as been built. A wonderfully rich golden harvest was soon gathered from the alluvial found high on these slopes, and from runs (or gutters) which got their rise on them, and were traced down gullies into a broad valley. In due course it was ascertained that the valley carried a main gutter which represented the unity of the higher ones, and further explorations proved this gutter to have a westerly and then a southerly trend toward and under a basaltic plateau, on the top ofwhich Ballarat West and Sebastopol now stand. In the records of alluvial gold mining all the world over the Ballarat field can be classed amongst the richest. Gold in pieces the size of beans, in, stringy filigree bits, in dust and in solid lumps (the largest of which weighed more than 2,200 ozs.), was obtained in the comparatively shallow ground on the slopes; and speaking generally, great and uniform richness was met with along a belt of country on which, in a north and south line, the present quartz mines of Ballarat East are at work. It was noticed by the diggers that when the gutters crossed the upturned edges of the ,strata, the gold deposits in them were patchy, and that when they trended north and south on this beltthey carried rich deposits for longer distances. In time it was also noticf!d that a class of stringy, irregular shaped quartz occurrences, in a bottom of soft slates, in the, immediate vicinity of tpe g)ltter, meant greater richness, and (in the aIluvial) on the higher ground slabs of quartz would now and then be met with, in which strings and spongy masses of gold were found. As the shallow alluvial became worked out the diggers turned their attention to the quartz occurrences, and, now and again the striking of a flat make of a very golden nature would cause quite a stir in the local mining world.

Apparently there is little inclination on the part of mining engineers to supplant the transmission of power by compressed air with it's formidable rival, electrical transmission. No doubt there are many advantages to be claimed for compressed air that render it parculiary well suited for the conditions which characterise underground work.

Jan 1, 1902

By G. S. Pauley

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: Case-based reasoning can be a catalyst for improvement). A new computer software technology known as Case Based Reasoning (CBR) can be used to produce small decision support systems that are economically viable. This is because the knowledge that they contain can be owned and maintained by their users. A CBR tool has been used to perform a pilot study with Anglesey Aluminium Metal Ltd. The results are encouraging. They suggest that a combination of CBR and participative design and implementation techniques (such as Checkland's Soft System Methodology) can achieve sustainable improvement in mineral processing functions. An explanation is presented of why traditional, rule based systems are often an ineffective way to implement support systems. It is shown that CBR may provide an appropriate technology solution. Methods of achieving sustainable benefit are indicated. The pilot study with Anglesey Aluminium Metal is used as a practical illustration of the development of a CBR application. A review of potential application areas and some observations about the implementation are presented

Apr 1, 1994

By A B. Opperman

For many years explosives energy has been utilized in mining and construction as well as many other applications which are vital to our way of life. Many types of explosives have made their contribution as technology has moved forward. One of the best known was dynamite, which for many years was the mainstay of explosives users. Although dynamite had many advantages over its predecessors, it had the principal shortcomings of being somewhat hazardous to handle and was known as a headache producer.

Jan 1, 1975

By Y. Luo

A PC based computer model has been developed by the authors for predicting the surface subsidence due to underground coal mining. Its reliability, comprehensiveness and user friendliness demonstrate that it is a good tool for the mine operators, government agencies and scientific researchers alike.

Jan 1, 1989

By Dolly Chakraborty, S. Ranganathan, S. N. Sinha

Pre-reduction of chromite outside the submerged-arc furnace (SAF) can significantly lower the specific power consumption in the SAF process. Conventional processes for the pre-reduction of the ore operate at relatively high temperatures, at 1400-1500°C. It is possible to enhance the rate of reduction at low temperatures by optimizing the flow rate of inert gas over the reaction site. The influence of the flow rate of inert gas on the rate of reduction of chromite ore was investigated. The rate of reduction initially decreased wit the flow rate of the gas. It increased subsequently at higher flow rates to be followed by a decrease again. There was an optimum flow rate at which maximum reduction could be obtained. It was possible to achieve high levels of reduction at 1200°C by optimising the flow rate of the gas. The degree of reduction obtained was comparable to that obtained at 1400-1500°C, by conventional process routes.

Jan 1, 2007

By D. N. Dietz

Jan 1, 1969

By R. Venugopal, T. C. Rao, N. Suresh

Experiments were carried out using the cyclone to treat coal in the size range -2.0+0 mm. The diameters of the cyclone outlets (vortex finder and spigot) were varied to study their effects on cyclone performance. The cyclone products were deslimed over a screen with an aperture of 0.075 mm. The performance of the separator was studied for washing coarse coal (-2.0+0.075 mm) and fines (-0.075 mm). Performance curves were plotted for the separation of -2.0+0.075 mm coal. The concept of a generalised distribution curve was adopted to predict cyclone performance. A mathematical representation was derived from the generalised distribution curve. The specific gravity of separation for individual size fractions showed a decreasing trend with decreasing particle size down to 0.85 mm, beyond which a reverse trend was noted. It was also found that the fine size fraction (-0.075 mm) does not separate on the basis of size or specific gravity but follows the water distribution

Apr 1, 1995