Search Documents

By Shaw-Shong Liew

This paper presents the design concept using floating piles to support 2500Ton oil storage tanks on a very soft alluvial clayey soil of about 40m thick in Riau Province of Sumatra, Indonesia. The floating piles of various penetration lengths were designed to support seven numbers of such storage tanks seating on a 20m diameter and 500mm thick reinforced concrete (RC) circular raft. The pile points have been strategically located at the RC raft. Varying pile penetration lengths have been designed to minimize the angular distortion of the thin RC raft and the out-of-plane deflection at the tank edge. Vibrating wire strain gauges were installed at different levels inside the ø350mm prestressed reinforced concrete piles to measure the load transfer profile during the static load tests and water-loading test. The installation and interpretation of the instrumentation are described and discussed. Boreholes, in-situ tests like piezocones, vane shear tests and standard penetration tests, and laboratory testing were carried out to obtain geotechnical parameters for the pile designs. Static load tests were also carried out on the spun piles of varying lengths of 24m, 30m and 36m respectively. It has been demonstrated that the floating pile system can be a cost effective design to support heavy structures on very soft compressible deposits with satisfactory performance. Finally, the design concept validated with the results of instrumentation is discussed.

Jan 1, 2002

By L. Adler

The proper transfer of roof loads from props and bolts to ribs and pillars can result in appreciable savings. The author shows how to plan such load reduction in underground mines. For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.&apos; This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.1 An underground opening overlain by a relatively thin immediate roof, and a thick main roof, is usually laid out as shown in Fig. 1. The total open span (T) between pillars or ribs is calculated on the basis of the main roof, and the secondary spans (L) on the basis of the immediate roof, so that a complete accounting of the existing loads is made. For this purpose the immediate roof is treated as a uniformly loaded continous beam, which is an indeterminate structure as shown in Fig. 2(A). The term systematic supports places the following two restrictions on the continuous beam: 1) Spans between all supports are equal: uniformity of spans. 2) Loads on all supports (excepting ribs) are equal: uniformity of supports. The usual mode of analysis of such a structure by beam theory is to divide it up into a series of simply supported beams with end moments as shown in Fig. 2(B)2 The problem now is to transfer a maximum roof load to the rib from the span immediately adjacent to it by permitting its support to deflect, and yet not fail the roof. Once this has been done, the load can be equalized on all other supports by permitting further degrees of relative deflection. It is necessary, therefore, to determine an expression for the constant load on each support, and the required deflections, in terms of properties of the roof. From Fig. 1: T/L0 = No and T/L = N [1] Where: T = allowable span of main roof, ft. (Calculated from S = Mc/l) S is allowable modulus of rupture, psi. M is maximum moment, lb-ft (in this case wT2/12). c is distance from neutral axis to extreme fiber, ft. I is moment of inertia with respect to the neutral axis, ft4. L,, = allowable span of immediate roof, ft (calculated as was T). L = actual span of immediate roof, ft. N0 and N are pure numbers where No < N and N is the integer just higher than Nu. For example: If T =100 ft and L0 - 15 ft 100 N0 =100/15= 6.667 . . .N= 7 L = T/N = 100/7 = 14.28 ft Consequently N = No + n where n is a positive fraction i.e.: 0< n < 1 Since from Eq. 1, T = NL = N0L0 Lo /L = N/No = N/N-n

Jan 1, 1961

By Teele Tuuna, Voglers Eesti OÜ

Blasting operations are a strong and important part in any kind of building and mining industry, a shot-firer profession is one of the oldest professions in the civilized world. It still serves an important and ongoing purpose in the modern economy all over the world. Europe, nowadays, values strongly the mobility of workers, the movement of know-how and labor force between different countries inside Europe. There are no borders for most of the everyday professions.

Jan 1, 2018

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By Henry M. Harris

The roll forming of oxide powders was studied in a Bureau of Mines investigation to find the conditions and parameters required to make satisfactory ceramic strip. High-quality porous or dense alumina, zirconia, and porcelain shapes were made by sintering strip roll-formed at room temperature from powders containing minor amounts of binder and water. Strips with thicknesses of 0.04 to 0.08 inch and bulk densities from 40 to 90 percent of theoretical densities were made. The parameters most important to formability were particle size, condition of the powders, and roll gap. Other factors affecting quality were speed and surface condition of the rolls, amount and type of binder, water content, and sintering conditions. Ceramic strip was formed at rates up to 78 feet/minute, which is 13 to 23 times faster than reported by previous investigators, and forming was done in a simple and inexpensive roll unit. Reshaping the strip was possible by cutting, grinding, shearing, and stamping. The following innovations were developed that allow roll processing not normally possible with ceramic powders: (1) Fine-sized powders were made into strip by preparing these as partially sintered granules; (2) thick strip was formed by pressure feeding powders into the rolls; (3) flexible strip was made using a rubber-base bonding agent; (4) corrugated strip was formed on shaped rolls; and (5) porcelain strip was densified and reduced in thickness by rerolling while hot.

Jan 1, 1970

By E. V. Lilford

Equity investors and project sponsors have divergent views about expected or minimum returns that should be generated by a mineral project. Irrespective of their views, the fundamental estimation of the corporate cost of capital remains singularly determinable, with additive components of risk and uncertainty often incorporated in the final analysis. This paper discusses and details the fundamental, numerical determination of the corporate cost of capital.

Jan 1, 2006

By P. Tittes, M. Deal, M. Spicher, S. McDaniel, J. Wickens

"Haile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The relatively low grade and refractory nature of the deposit has been a challenge for efficient processing since the start of mining on the property. Early processing techniques included gravity separation and barrel chlorination. The last operation employed heap leaching in 1985 through 1992. After being closed and reclaimed for over 20 years, the property is poised to re-open and produce once again. In this chapter of the Mine’s legacy, flotation and ultra-fine grinding will be employed to achieve economic extraction of gold and silver from the pyrite. This paper briefly reviews some of the mine’s history, the metallurgical testing, the flowsheet and discusses design considerations.INTRODUCTIONHaile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching in 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that has delineated over 62 tonnes (+2M ozs.) of gold in reserve at an overall grade of 2 ppm (0.06 opt). This paper provides a brief history of the property, a summary of metallurgical testing, description of the process flowsheet and discusses design considerations.HISTORY1827 – 1837Gold was discovered in creek beds on the Haile property in 1827. The property was owned by Benjamin Haile, and the first few years of production came from placer mining. After gold was discovered in schist beds to the sides of the streams, Haile expanded the operation by leasing 18 meter-square (50 ft.) plots to local planters. These planters used slaves to work the small excavations in the agricultural offseason. The gold ore was taken to arrastras where the free gold was liberated and recovered. The excavations were above the water table, generally less than 18 meters (60 ft.) down, and it was noted then that gold could be found embedded in sulfides and difficult to extract."

Jan 1, 2013

(Published by courtesy of the Great Boulder Pty. Gold Mines, Limited)1. INTRODUCTIONThe faults described in the following paper are of a somewhat unusual character, and have presented a serious problem both in the development and mining of many ore-bodies on the Eastern side of the Boulder Belt. They are mentioned only briefly in the literature of the field, but were observed by, both Stillwell (1)t and Gustafson (2), and have been studied by other geologists and operators in various parts of the &quot;Belt.&quot; Their effect on the lodes of Hamilton Section, Great Boulder Mine, was described by King (3) in 1937, and, during recent years, they have been encountered in most of the Great Boulder workings extending east of the Boulder Dyke.Although this paper is based mainly on a study of faulting and development problems on the Great Boulder mine, the general conclusions reached may be applicable to the solution of similar faulting problems in other mines throughout the field.In order to arrive at a clear understanding of the somewhat complicated relationships which the east-dipping faults bear to the lode systems it will be necessary to give a brief outline of the salient geological and structural features of the &quot;Belt&quot; before proceeding to describe the faults themselves.2. GENERAL GEOLOGYThe most recent descriptions of the geology of Kalgoorlie are those by Stillwell (1) and Gustafson (2) and the reader is referred to these as representing the basis of current knowledge of the geology of the field.The Boulder Belt is comprised of a central core of altered quartz dolerite which is flanked on either side by fine grained greenstones and lavas, usually referred to as the calc schists. Down the centre of the quartz dolerite mass there is an infolded bed of slate (2, p. 105) which has been intruded in lit par lit fashion by albite porphyry; the composite body of slate and porphyry so formed is known as the &quot;Boulder Dyke.&quot; Numerous smaller porphyry dykes intrude both the quartz dolerite and the calc schist; these vary in composition and range from chloritised hornblende porphyrites to albite porphyries.The whole of the rock assemblage has been subjected tG a considerable amount of folding, faulting, shearing and fracturing, the greater part of which took place before the formation of the lodes.

Jan 1, 1941

A wide-ranging base of jig data was collected from various types of commercial jigs in 9 coal preparation plants in China, and a complete data analysis was made. It was found that the sharpness ofseparation was very variable, which demonstrates the complex interplay of the many factors which influence jig performance. Tests showed that there exist optimum frequency ranges in each compartment of a jig. Stepwise regression analysis indicated that the sharpness of separation is most sensitive to the intake fraction ofthe air cycle, the frequency, and the feed rate. By means of non-linear curve fitting techniques and statistical analysis, several mathematical models were developed to describe both partition curve and the jig performance, for simulation purposes.

Jan 1, 1986

By José A. Rios, José A. Vidalôn

The case study of a highland area in the Central Andes of Peru, where many abandoned polymetallic mines are found, is presented. Some of these mines generate metal leaching and acid rock drainage (ML/ARD) or have potentially ARD generating (PAG) tailings/waste rock storage. Effluents are discharged into the first of two lakes in line, which act as reservoirs for irrigating an important valley in the desert coastal region. Drainage fees, their relationship with the deposit and the solid-wastes mineralogy are discussed, as well as variations in water and sediments composition, the benthos, and the aquatic/riparian flora/fauna in these lakes.

Jan 1, 2000

By Wolfgang G. Brunner

A 3800 m long temporary water-retaining dike has been constructed under extreme conditions in the harsh northern climate to enable two of the kimberiite pipes at the Diavik Diamond Project reserve to be mined using open pits. The Diavik Diamond Project is located on East Island at Lac de Gras in Canada&apos;s Northwest Territories, approximately 200 kilometres south of the Arctic Circle. The dike which has been constructed in up to 25 m deep water from crushed granite quarried from the site projects into Lac de Gras encircles the first two of the kimberiite pipes to be mined. An 800 mm wide diaphragm cut­off wall constructed of bentonite, cement and crushed rock, totalling 33,000 m2, and a two-phase jet grouted curtain wail at its base, totalling 8,400 m2, have been installed through the dike and underlying till foundation into bedrock. The cut-off is designed to minimise water seepage from Lac de Gras through the dike. In order to ensure that the dike had adequate internal stability and diaphragm wall construction could proceed safely, the crushed rock fill material dumped into the lake was first compacted by TR 75 deep vibrators. In 2000, Bauer Maschinen GmbH of Schrobenhausen, Germany were awarded the contract for the supply of all specialist foundation equipment required on site and for providing technical support to the Canadian main contractor Lac-de-Gras-Construction throughout the construction of the cut-off walls during 2001 and 2002. Installation of the cut-off walls was completed in July 2002, three weeks ahead of schedule, and dewatering of the inner dike areas commenced just 5 days later and has continued throughout August and September. After completion of extensive testing of the diamond recovery plant, the mine is scheduled to go into full open pit production in February 2003.

Jan 1, 2003

By Oliver Bowles

This paper is the third of a series of reports on asbestos prepared by the Bureau of Mines. The reports already issued contain general information, including descriptions of deposits throughout the world.3/ The present paper deals chiefly with milling and marketing. Many grades of asbestos are marketed, and an important phase of milling is the grading of fiber; these subjects therefore are related so intimately that contiguity in their treatment is fully justified. Although the Bureau of Mines is interested primarily in the mining and preparation of raw materials, the fabrication of asbestos products has attained such importance in the United States that brief reference to processes of manufacture is included. CLASSIFICATION OF FIBER Canadian asbestos fibers are divided into three main groups - crudes, mill fibers, and shorts. The term "crude" is applied to fiber of spinning grade measuring three eighths inch or longer, that is. hand-cobbed and not passed through a mill. Mill fibers are obtained by crushing and beating the fiber-bearing" rock, until the, asbestos is freed and, then removing the fiber from the rock by screening or air separation. Shorts are the lowest grades of mill products.

Jan 1, 1935

Column flotation has been successfully implemented on a production scale in the Athabasca oil sands. In this application, bitumen is recovered and mineral matter is simultaneously rejected from a middling stream originating from a primary separation vessel. Exploiting the natural hydrophobicity of bitumen, the middlings streams have traditionally been processed utilizing conventional, mechanical flotation cells. Although these cells offer adequate bitumen recovery and mineral rejection rates, operating costs are high due to the required maintenance of the wetted mechanical components. In comparison, column flotation provides superior metallurgical performance while offering a lower maintenance demand. Both metallurgical and mechanical characteristics of column flotation are discussed to demonstrate the benefits of this technology for the recovery of bitumen from oil sands.

Jan 1, 2012

By J. M. A. Geldenhuis

This work is concerned with studying possible reactions in the ilmenite furnace which may control the product quality of both slag and metal. Two different approaches were followed: comparing actual furnace slag compositions with the calculated equilibrium values and using commercial oxygen probes to measure the effective partial oxygen pressure in the slag and metal. It appears from a comparison of actual furnace slag compositions (in terms of the distribution coefficient of vanadium) with equilibrium values, that the TiO1.5-TiO2reaction may fix the effective partial oxygen pressure for the vanadium reaction. This possibility was tested using commercial oxygen probes (traditionally applied during steelmaking) to measure the effective oxygen partial pressure of both the slag and liquid iron in Iscor?s 3MVA pilot plant ilmenite furnace. From these measurements, it appears that commercial oxygen probes containing zirconia solid electrolytes can be used to measure the effective oxygen potential of both the slag and liquid iron. This oxygen activity correlates well with the FeO content of the slag. The results, furthermore, clearly illustrate that equilibrium conditions are not attained in the ilmenite furnace during the production of high titania slags, since the effective oxygen potential of slag and metal differ substantially.

Jan 1, 1999

By M Rafty, A Markham, S Atkinson, M Heyting

Over recent years there has been a significant increase in the number of miners in the Pilbara region of Western Australia targeting channel iron deposits (CID) located in valleys, intersected by ephemeral creeks and below the groundwater table. The falling iron ore price has triggered a drive to reduce cost and maximise yield. Creek diversions provide an opportunity to maximise the utilisation of orebodies and extend the life-of-mine.Creek diversions that are required during mining operations to access ore and provide flood protection have historically been constructed as uniform engineered channels designed primarily for flow conveyance while minimising earthworks costs; however, the design of diversions becomes more complex when they are required to function in a similar way to the existing creek system during operations and remain stable during more extreme events than would typically occur following mine closure, in accordance with current regulatory guidance. The design specifications for closure are often more rigorous than the operational phase, and could incur significant additional cost to implement retrospectively if not planned and designed upfront.The complexity of diversion design depends on site specific factors such as: the size of the creek to be diverted; hydrology; corridor restrictions; geomorphology; hydrogeology; geology; environmental and heritage values; potential impacts and the risk to operations and environment. The complex interactions of these factors must be well understood and hydraulic modelling undertaken to characterise the existing creek system, demonstrate the diversions, provide adequate flood protection during operations, and can function in a similar way to the existing system following mine closure. This paper presents key design considerations for Pilbara creek diversions, operational and closure requirements, mine planning considerations, risks, cost saving opportunities, and the benefits of an integrated approach to design.CITATION:S Atkinson, A Markham, M Rafty and M Heyting, 2017. ‘Back to the future’ – resilience in historical context and implications for the future, in Proceedings Iron Ore 2017, pp 367–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By I Thin, L Morizzi, C Seymour, G Mungur

Olympic Dam has been investigating mine design options for the South Mine Area (SMA), which will continue using the existing sublevel open stoping (SLOS) method. The SMA is an undeveloped mining area, located south of the existing underground mining areas currently in production at Olympic Dam. The SMA study reached the stage where geotechnical inputs were required for stope design, infrastructure location and ground support forecasts. A large database of geotechnical data was collected to inform open pit designs for the ODX (Olympic Dam expansion) project (resulting from 659 drill holes). This geotechnical data has since been reprocessed to align with design inputs required for the SLOS mining method. The result has been the construction of a preliminary three-dimensional mining rock mass model (MRMM) that has been incorporated into preliminary stope mine design and infrastructure layout assessments, which have taken into account the predicted prevailing ground conditions.As with any model, it is necessary to improve the confidence in its predictability; therefore the model must be calibrated. The preliminary SMA MRMM was no exception. First pass calibration was possible with results from underground geotechnical window mapping from exposed rock mass conditions in the lateral development and surface geotechnical holes for ventilation shafts.The SMA project continues to advance and has started a program of resource drilling. Selected holes have been identified that target data limited areas. This will ensure that the data gaps are infilled in order to maintain the required data density required to improve the model confidence. In addition, further underground window mapping in the SMA will provide ‘mine scale drill hole’ data that can be used to either update the MRMM or as part of planned future calibration. Stope performance data from stopes will provide further valuable data for calibration purposes.The proposed paper will present the process and findings that have been followed in order to establish a well calibrated geotechnical model that can be used with an acceptable level of confidence in the ongoing refinements of the mine design and planning process for the SMA.CITATION:Thin, I, Morizzi, L, Mungur, G and Seymour, C, 2016. Building and calibration of a geotechnical model for sublevel open stope design at Olympic Dam, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 523–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M Stewart

The structural framework for the major gold deposits of the Reefton Goldfield was largely established in the 1930s after a detailed regional geological mapping programme. Recent new mapping has now substantially modified the structural framework of the Globe Hill - Devils Creek area and the Waiuta area. Using bedding-cleavage vergence as a method of establishing fold limb facing, many new fold structures have been identified, some of which conflict with long-established structures such as the Globe Hill and Waiuta anticlines. In addition, the mapping of areas of west- versus east-facing limbs constrains the position of many faults. The mineralised Globe-Progress Shear is one such fault which graphically demonstrates major structural discordance of the folds in the hangingwall compared to the footwall. Recognition of the folding is establishing the structural framework for understanding of the origin of these productive gold mining areas.

Jan 1, 1996

By Kevan J. R. Ford, Chris A. Fleming, Robert D. Henderson

"Kinross Gold Corporation’s Maricunga mine in Chile presents an ideal opportunity to apply the SART process to a heap leach operation. Given increasing levels of cyanide complexed copper in current pregnant solutions from Maricunga heaps (over 300 ppm Cu), there is a need to reduce these levels and decrease cyanide consumption and cost. Additionally, a means of disposing of this copper is required, preferably as a saleable product. The well published SART process applied to gold-copper cyanide solutions was selected as it allows rapid precipitation of cyanide soluble copper as a relatively pure copper sulphide. The process also allows effective recovery and recycle of cyanide back to the heap leach operation.This paper reviews the SART process chemistry and presents a summary of SART bench-scale and pilot plant testwork completed by Kinross. Key design parameters and engineering aspects of the proposed plant at Maricunga are discussed. SART plant operating costs and net revenue analysis are included and illustrate the compelling economics of installing a SART process plant. INTRODUCTIONMaricunga OperationCompañia Minera Maricunga (CMM), fully owned by Kinross Gold Corporation, operates the Maricunga mine (formerly Refugio) which is located 120 km due east of the city of Copiapó at an elevation of 4,200m above sea level in the Andes mountains of northern Chile. Figure 1 shows a map of the location of the Refugio mine relative to other gold and copper mines in the region."

Jan 1, 2008

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Samples of crude magnesium produced by the Mintek Thermal Magnesium Process were refined in two stages. The first stage consisted of co-melting of batches of the crude metal and MgCl2-KCl flux (cleaning), followed by stirring at 30 rpm for 30 minutes and settling of the sludge (mixture of molten salt and solid impurities) from the magnesium melt. The operating temperature was 680?730°C. Most of the contained calcium and significant proportions of iron and silicon were transferred into the sludge phase, which left a metal containing, on average, 950 ppm Si, 470 ppm Fe, and 230 ppm Ca. In the second stage, small-scale refining tests were conducted on cleaned samples from the first stage, as well as on crude magnesium. FeCl3 was used as the refining agent. These tests were carried out at 715?760°C with various amounts of the refining agent. The refined metal was suitable for the production of various magnesium alloys, particularly AZ91D.

Jan 1, 2006

By Jerry Wallace

The goal: At an industrial site, sever a well pipe containing an interior obstruction in a timely, cost effective manner by using a shape-charge to cut through the casing more than 50 meters below ground surface from the outside, doing so while inside a larger pipe, without damaging the larger pipe. The problem: Pumps and retrieval tools stuck nearly 50 meters below ground surface inside a 305 mm diameter by 9.5 mm wall thickness water well casing. The well, depth of 185 meters, had to be inspected for contaminates then properly decommissioned before industrial expansion could take place overhead. The limitations: A 508 mm diameter pipe had been driven around the 305 mm pipe to a depth of 63 meters. The usable internal diameter of the larger pipe was about 480 mm while the smaller pipe had buckled at one point forming a 350 mm wide spot. The charge thickness was limited to less than one-half the difference. Additionally, water that filled the annular space between the two pipes had to be displaced for the charge to work properly. The solution: Enlist the support of the shape-charge manufacturer to design, build and test a charge to work under the conditions present, then make it work in the field.

Jan 1, 2000