Search Documents

By T. T. Nguyen, D. R. Gunasegaram, D. Celentano

"Heat transfer rates at the casting-mold interface are believed to be substantially reduced by the formation of an interfacial gap during the course of solidification of aluminum alloys in permanent molds. In the current work, the effect of force-cooling a permanent composite mold on (i) the initiation and growth characteristics of the gap and (ii) interfacial heat transfer rates are studied. Interesting comparisons are made with the case where no cooling is employed. Casting and mold displacements are measured using L VDTs, and the mold is force-cooled by air jets.IntroductionIn a gravity casting situation where an aluminum alloy solidifies in a permanent mold, a gap initiates and grows between the shrinking casting and the expanding mold (1). It is widely believed that the formation of this gap, customarily referred to as an 'air gap', results in a substantial reduction in the heat transfer coefficient at the casting-mold interface (2), and hence is an important factor in solidification studies.The nature of the air gap formation process is thermo-mechanical. The rate of heat loss from the casting first determines the rate of solidification, which, in turn, decides when the gap initiates. The reason for this is the requirement for the solidified casting surface 'skin' to gain sufficient thickness, and hence strength, to be self-supporting. Once the gap initiates, the gap width controls the rate of heat loss from the casting, which, again, determines the rate at which the gap expands."

Jan 1, 1997

By S. Shairp

The first commercial application of the Dynatec two-stage zinc pressure leach process commenced operation at the metallurgical complex of Hudson Bay Mining and Smelting Co., Limited in Flin Flon, Manitoba in 1993. A key feature of the successful leaching operation is the presence of iron in solution, which facilitates oxygen transfer in the autoclaves and enables rapid oxidation of zinc sulphide minerals. At the same time, the solution from which zinc is recovered must be essentially iron free. Precipitation of iron from the solution starts in the autoclaves and is completed in subsequent atmospheric purification steps. Conveniently, these iron precipitation steps also remove nuisance elements such as arsenic and fluoride from the solution, while producing solids with good liquid-solid separation characteristics. This paper provides an overview of the current operations in Flin Flon, with particular reference to the behaviour and deportment of iron throughout the zinc plant.

Jan 1, 2006

By Bob A. Hamaguchi

The Trojan Tailings Pond at Highland Valley Copper developed in only 15 years from a biologically inactive water body into a productive lake with a well established aquatic ecosystem. This process was assisted by a few simple and inexpensive procedures including fertilization and introduction of essential organisms. The success at the Trojan Pond has encouraged the use of similar techniques in other water bodies on the mine site. This paper details: ??The history, water quality and thermal behavior of Trojan Tailings Pond ?Techniques used in fertilization; introduction of micro-flora (algae etc.), large aquatic plants, zooplankton and invertebrates ??Selection and sources of suitable transplant materials ??Rate and extent of vegetation establishment ??Biomass production ??Rates of organic sediment accumulation over tailings ??Bacterial activity in the sediments ??Improved water quality through the bioaccumulation of aqueous metals in plants and the subsequent bacterial binding or precipitation of that metal during decomposition in the tailings sediment. Robert A. Hamaguchi graduated with a Mining Diploma from the British Columbia Institute of Technology in 1971, followed with a Bachelor of Applied Science in Mineral Engineering from the University of British Columbia in 1975. Since graduation, he has worked for numerous open pit mining operations throughout British Columbia. In 1991, he joined Highland Valley Copper working as an Environmental Engineer responsible for government liaison, reclamation, decommissioning and other environmental duties. Heather M. Larratt graduated from the University of Calgary in 1978 with a B.Sc. in Environmental Biology (First Class Honors). She has provided drinking water management and reservoir design for numerous cities and irrigation districts in British Columbia for 20 years. Heather has also worked for 12 years in reclamation of mine water, including passive SRB water treatment systems. Mark R. Freberg joined Highland Valley Copper in 1991 after working at number of mining operations in British Columbia and the Northwest Territories. He graduated in 1979 with a Bachelor of Applied Science degree in Mineral Engineering from the University of British Columbia.

May 1, 2001

"Investment in diamond exploration has been declining over the past decade, in spite of positive long-term industry fundamentals and a growing interest in diamonds as an investment category. The lack of new significant discoveries in recent years has eroded investor confidence, yet no new discoveries are possible without investment in exploration. Junior ‘mine finders’ have been the hardest hit. Their agility, tenacity, and appetite for risk are not sufficient to attract the funding required, even at the greenfield stage. Developing new discoveries into mineral resources can be crippling without solid financial support. Junior incubators could play a crucial role, especially at the project evaluation stage – but where are they? Alternatives to traditional funding mechanisms have become available, many still untested in the junior diamond exploration space. Valuable lessons can be drawn from the past and used to inform emerging new strategies. IntroductionDiamonds are the ultimate expression of love. Their ancient and timeless allure continues to influence consumer emotions and behaviours across continents, cultures and age groups. Analysts are predicting a sustained supplydemand shortfall in the years ahead which will trend diamond prices generally upwards. With positive long-term industry fundamentals, one cannot help but wonder why funding for diamond exploration and development projects is so scarce.Investment in exploration across commodities – including diamonds – has been declining for a number of years, reaching a historic eleven-year low early in 2017. The lack of major diamond discoveries in recent years has done little to strengthen the case for investing in diamond projects, yet no new discoveries can be made without investment in exploration.Global estimates of known carats in the ground stand currently at 2.5 billion carats, which equates to around 18 years of production at current levels of 140 million carats (mct) per annum. Sustainable replenishment of depleting diamond resources is possible only through the development of new discoveries. This is what junior explorers are best at – but they need investors to fund their evaluation activities from early in the project development continuum."

Feb 1, 2019

By Efstratios Karampinos, John Hadjigeorgiou, Philippe Morissette

"Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting appropriate systems at the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation.Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights into the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement throughout the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is often not available at mine sites. Even when the expertise is available, it requires a major time commitment and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support.Rock reinforcement is an integral part of all ground support systems used in underground mines. Long, flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This article focuses on the optimization of the cable-bolting strategy in squeezing conditions at the LaRonde Mine in Quebec, Canada by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 4, 2018

By Carlos Neira R

Dentro de la minería, el sistema de control tipográfico es importante puesto que guía las labores de exploración a través de las mediciones del terreno y el cálculo de coordenadas. En ese sentido, el presente texto señala una nueva forma de aplicación mediante el uso de un microcomputador y los programas de cómputo, de forma que este apoya los cálculos y graficación de poligonación, así como los cálculos de triangulación compensada por vértices y figura, los de cuadriláteros ajustados por mínimos cuadrados, los de coordenadas y el cálculo de movimiento de tierras.

Aug 26, 1988

By D. Wheeler

Similar to modern day petro-chemical processes, the flotation column is a complete break from the conventional manner of floating on a batch basis in cells. The column has a reputation of being only suited for cleaning applications, particularly that of molybdenum cleaning. The original column, invented and developed by Column Flotation Co. of Canada, Ltd., was developed as a Rougher-Scavenger. Only after proving its capability in this field was cleaning allowed. One rougher-scavenger column in closed circuit with a cleaner column produced better grade and recovery than a conventional cell plant consisting of one stage of roughing, two scavenging and four stages of cell cleaning. Three cleaner columns replaced 13 stages of conventional cell cleaning and resulted in higher grades and recoveries. The gentle countercurrent action of the column itself together with complete automatic control enable this machine to produce such results.

Jan 1, 1986

The optimal production of the metals needed by society is best achieved by a close synergy between concentrate production and smelting. For over 75 years commencing in 1923, such a close relationship was enjoyed between the Sullivan Mine in Kimberley, British Columbia and the Trail zinc-lead complex. An effective program of continual change and improvement at the Sullivan concentrator was achieved through a strong entrepreneurial spirit. This spirit was in part maintained through a favourable location in south-eastern British Columbia that resulted in a dynamic local community that has survived the closure of the mine. Innovations to be reviewed include feed forward reagent control, the use of column flotation to zinc and lead cleaning and the application of ultrafine grinding coupled with concentrate dewatering using hyperbaric filter technology.

Jan 1, 2005

By C. F. Wingquist

As part of an ongoing study to determine how the wear of mining tools affects dust generation, the Bureau of Mines has measured bit tempera-ture rise during cutting of abrasive rock. Radial bit wear-flat tem-peratures generated by linear cutting in Berea Sandstone were measured as a function of cutting depth and speed. Depths of cut (DOC) were 1/8, 1/4, and 1/2 in, and cutting speeds were 10, 40, and 80 in/s, respectively. Temperature sensing was accomplished by emplacement of a miniature thermocouple into the center of the wear flat. Temperatures observed ranged from 2000 to 5000 C. Correlation between depth and temperature was weak. Temperature increased linearly with speed at 1/2-in DOC, but data taken at 1/8-and 1/4-in DOC produced inconclusive results. The results indicated that at least for deeper cuts (1/2 in), bit temperature, and therefore wear, can be reduced by lowering the cutting speed.

Jan 1, 1987

By Brian Wilson, Megan Atkinson, Richard Diggle, Nathan Sweeney

"Ruskin Dam, located near Mission, British Columbia, was constructed in 1929 and 1930 and comprises of a concrete gravity dam structure founded on bedrock. At the right abutment, which consists mostly of dense to very dense sands and silt, the dam abuts against overburden soils, and connects to a cutoff wall system consisting of sloping concrete slabs. Significant seepage and piping issues were encountered during first filling of the reservoir in 1930. In 2012, BC Hydro, the owner of the dam, awarded a contract for the construction of seepage control measures at the right abutment, including construction of a plastic concrete cut-off wall extending upstream of the dam, a plastic concrete seepage training wall extending downstream of the dam, tie-in of the new cutoff wall to the dam, consisting of jet grouting of the soils adjacent to the dam to allow for the construction of the special cutoff connecting the cutoff wall to the dam, and construction of additional jet-grouting ground improvement downstream of the dam.Integral to the upgrade was the requirement for the special tie-in cutoff wall, consisting of a highly flexible, impermeable membrane to connect the concrete dam to the new, 1 m thick plastic concrete cutoff wall. The tie-in extends vertically into bedrock through the dam and jet grout columns constructed adjacent and beneath the overhanging portion of the dam at the right abutment. The membrane is required to survive the anticipated earthquake induced deformation between the dam and the abutment soils.This paper describes the processes used to develop a material suitable to meet the specified flexibility and permeability criteria, as well as the innovative construction techniques utilized to construct the slot and place the bituminous material within it. The final dimensions of the slot were in the order of 7 m long by 25 m deep by 0.17 m wide. The bituminous material was placed under a head of water which was required to maintain stability of the slot, and was placed at temperatures in excess of 120 degrees Celsius."

Jan 1, 2017

By Samuel S. Adams

The Permian Salado Formation of west Texas and southeastern New Mexico is composed of halite and subordinate amounts of anhydrite, clay and potassium and magnesium-bearing evaporite minerals. Aspects of the geochemistry of the Salado Formation have been investigated through studies of the stratigraphy, mineral assemblages, textures and minor element content of the salts. These studies provide information on the origin of the evaporites when combined with data on equilibria in saturated salt solutions. The principal potash ore zone in the district is composed essentially of halite (NaC1) and sylvite (KC1). Data on the color, bromide content, and proportions of halite and sylvite suggest that this simple assemblage is the product of a series of replacements rather than primary precipitation. The bromide content of the salts also indicates that the brine which precipitated the Salado Formation was derived from the dissolution of older evaporites rather than the simple evaporation of sea water.

Jan 1, 1966

By R. Cavanagh

Studies relating to the fixation of sulfur by reaction of 4 to 8 mm diameter cylinders of calcined limestone or dolomite with high strength sulfur dioxide in the temperature range 880°C to 1020°C were undertaken. Dolomites are far superior in sulfate capacity and reactivity than dense limestones even at high strength SO2. The sulfation reaction was first order with respect to SO2 concentration below 100 percent. Zero reaction rate at 100 percent SO2 concentration indicates that sulfate was the exclusive reaction product and that sulfite had no role in the reaction. At relatively low SO2 concentrations gaseous diffusion through the reaction product layer has a marked effect on the rate. As SO2 concentrations were increased up to 100 percent more complex rate controlling mechanisms unfold. By sectioning partially reacted dolomitic limestone pellets a moving interface was observed. Reaction ceased because of pore plugging for dense non-porous limestones at 30% conversion. With dolomitic material virtually complete sulfation of the calcium was observed. S.E.M. analysis showed that the average atom ratio Ca:S was 1.01, thus supporting the argument that little if any of the magnesium was sulfated.

Jan 1, 1996

By Brinton C. Brown

This paper describes the methods and equipment developed at the Bureau's Experimental Oil-Shale mine near Rifle, Colo., for placing men in position to scale loose rock from the walls, pillars, and roofs of high stopes or rooms. The equipment developed at Rifle has application not only in oil-shale mining but in most of the country's underground limestone mines and in the exploitation of other mineral deposits mined in high stopes by room-and-pillar methods. Equipment in use at Rifle includes: 1. A boom-type scaling rig with a self-leveling platform constructed on a small "cat"-mounted crane. Men working from the platform on this machine can efficiently scale mine walls and roofs 27 feet above the floor. 2. A conventional fork-lift truck modified to provide a remotely controlled working platform from which men can scale to heights 27 feet above the mine floor. The platform on this unit is larger than on the boom-type rig and allows the men to inspect larger areas of the mine wall from a single setting of the machine. 3. A third rig, consisting essentially of a platform mounted on a tele-scoping tower, designed and built to elevate men 65 feet above the mine floor. Versatility of this machine permits men to work from the platform at heights of 5 to 65 feet. In the operating position, the unit requires a minimum clearance of 25 feet. In the nonoperating position the tower of the machine folds to an over-all height of 15 feet 10 inches to permit travel through haulageways. 4. An industrial gun, lightweight scaling bars, and mechanical scalers, which have been tried for removing loose rock from the mine walls with varying degrees of success.

Jan 1, 1950

By K Faure

At Sams Creek a peralkaline granite porphyry dyke hosts gold-bearing sulfide-quartz-siderite veins. The granite dyke intrudes Ordovician-Silurian metapelite and quartzite, and has thin lamprophyre dykes along its contacts. The mineralised veins and the granite and lamprophyre dykes have been deformed during several phases of folding, the youngest of which is Early Cretaceous. The granite has been hydrothermally altered, with early magnetite-siderite¦biotite alteration overprinted by sulfide and quartz-siderite veins and quartz-perthite-albitesiderite-pyrite-rutile¦sericite alteration assemblages. The sulfide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite ¦ graphite, with minor quartz and siderite. The gold contains significant silver (up to 30.8 wt per cent) and ranges in fineness from 692 to 844. Immiscible liquid-rich fluid inclusions, in quartz protected from recrystallisation by enclosing arsenopyrite, contain carbonic liquid that homogenised at temperatures of 320 - 355¦C. The Sams Creek gold deposit is distinguished from the orogenic gold deposit type by its stockwork veining, magnetite-siderite¦biotite alteration, high sulfide content, ore mineralogy and the absence of mineralisation in the metapelite country rocks. Features of the Sams Creek gold deposit do not fit neatly into existing classifications of granite-related gold-bearing deposits. The peralkaline composition of the Sams Creek granite and the absence of molybdenite and paucity of chalcopyrite, are major points of difference with gold-rich porphyry copper deposits. The presence of a lowsulf idation-state ore mineral assemblage, carbonate alteration and carbonic fluid inclusions at Sams Creek are typical of many of the reduced granitic intrusion-related type of gold deposit. However, notable differences are: the reduced type granites are metaluminous and calc-alkaline; and Sams Creek only has high As in contrast to elevated Bi, W, As, Mo, Te, and Sb in the reduced type. The Sams Creek deposit also shows affinities with gold deposits associated with alkaline magmatism, and it appears to be a new variant of this type as an As-Au deposit associated with a peralkaline granite and lamprophyre.

Jan 1, 2004

By R. E. Hamilton

Automation is a word whose meaning has been broadened by popular usage to include any labor saving device. We with restrict our usage to the replacement of human judgement by instrumental measurement and mathematical analysis in the control of industrial processes. Mineral concentration is an area which has resisted automation because of the great difficulty in developing measuring instruments which can exist in the rugged environment and can measure useful properties with acceptable accuracy. This is not the only factor limiting progress, but until recently it has been of over-whelming importance. The development of on-stream X-ray analysers, magnetic flowmeters and nuclear density meters for mineral slurries has eliminated this obvious barrier and is enabling us to locate and attack the less obvious problems which still limit our ability to automate concentrators. If we examine the history of automation in industries which are highly automated we find that it has usually gone through three distinct phases. The first phase has been regulation. This is the simplest form of control and involves manipulating some variable whose value is of no importance in order to maintain the value of some other variable which is important at a constant specified value in spite of disturbances which may occur in other variables which affect it. A simple example is the use of a control valve to maintain a constant flow of fluid in a line in spite of changes in pressure in the vessels at the ends of the line. The position of the valve stem is of no consequence, as long as it is within its operating range. Unfortunately we soon run out of variables which can be

Jan 1, 1971

By Mark Kennedy, Allan MacRae, Cameron Hams

New technology projects, particularly those involving first-of-a-kind metallurgical facilities, have a poor track record of achieving their overall financial targets, as they incorporate technological risks in addition to normal project risks. Traditional project management tools focus on risk from concept development through implementation, but typically fail to address the additional risks associated with a new technology project including slow start-up, slow ramp-up, and failure to achieve design performance (quality or throughput). These additional risks affect future cash flows produced by the project and hence its value, typically measured as net present value (NPV) or internal rate of return (IRR). Common accounting practice is to reduce the present value of future cash flows by applying a chosen discount rate, often reflecting the corporation's cost of capital. This discount rate does not contain an allowance for technological risk, which is often underestimated or misunderstood by both the financial and engineering project managers. This paper will focus on the topic of project risk and new technology, and how these play a role in the probability of achieving the predicted future cash flows. By properly addressing technological risk in the form of risk-weighted returns, marginal projects can be prevented from proceeding, while sound projects can be given the additional time and resources required to achieve the optimal level of front-end-loading (the level which returns the maximum risk-weighted net present value). A simple set of mathematical tools should enable engineers and financial professionals to establish a common level of understanding, thereby leading to a more accurate assessment whether a new technology project is ready to pass through its next level of approvals.

Jan 1, 2011

By Diógenes Uceda

Dado que la aplicación de agua durante la extracción minera limitó su uso a la separación física de los minerales pesados como el oro nativo y el óxido de estaño, se utilizaron métodos hidrometalúrgicos que contienen reactivos en soluciones acuosas y orgánicos para producir metales y compuestos metálicos. En ese sentido, el presente texto describe la historia, procesos, ventajas, desventajas y el estado actual de la hidrometalurgia.

Apr 1, 2017

By Eric Jacobs

"Building and operating tunnels has been a highstakes endeavor in terms of costs, complexity, safety and impact on contractors, owners and the public for a long time. There are many variables that need to be closely monitored and managed to construct a tunnel on-time, on-budget and safely. Once built, there are also many elements that need to be monitored and managed to operate a tunnel safely and efficiently.Fundamentally, the risks to the safe and efficient construction and operation of a tunnel are a function of the degree of harm and the likelihood of the harm occurring. From a cyber security perspective, risk assessments used to inform decision makers and support risk responses are typically based on identification of relevant threats; internal and external vulnerabilities; the impact that may occur given the potential for threats to exploit vulnerabilities and the likelihood that harm will occur. This article focuses on creating awareness of vulnerabilities associated with technology used in tunnel construction and operation and some of the challenges associated with remediation of these vulnerabilities. As we all know, technology has been evolving at an accelerating pace and infiltrating every aspect of our lives in new and often exciting ways. In the world of tunneling, sensors and systems that provide position and time have become accurate, rugged and cost-effective enough to come out of the research labs and into the equipment and systems used every day. There are many opportunities to employ connected computing devices and sensors to costeffectively capture, integrate and analyze key data with minimal latency to manage risk better, improve safety and avoid surprises."

Jun 1, 2019

By M. Z. Emad, M. U. Khan, A. ur Rehman

Stemming plugs are used as an accessory in drilling and blasting industry. They supplement conventional stemming material (i.e. drill cutting) with retention of gases in the drill hole that result in better fragmentation of rock and improved explosive utilization. Better fragmentation and explosive utilization along with economic benefits enhance efficacy of the project. Incorporation of stemming plugs in drilling and blasting industry is in exercise for about thirty years. The efficiency of stemming plugs is a key factor in their rising induction in mining industry. Different studies have been conducted on the economic viability of these plugs. The focus of this paper is the selection of stemming plugs for a bench blasting operation and the examination of blasting operation efficiency based on ergonomics and human factors. Three types of stemming plugs were evaluated during multiple blasts at a limestone quarry. Their performance was evaluated using split desktop software. Based on the human factors plastic molded stemming plug (stemming plug-1) was found to be the best among all selected plugs. INTRODUCTION Surface mines and quarrying operations heavily depend on bench blasting to achieve high volumetric targets and production demands. Use of explosives is the most economic method adopted for rock breakage and movement. Extensive research had been performed to enhance explosives energy utilization. This include changing the drilling pattern, application of air decks, stemming plugs, and use of other supportive devices. Optimization of explosive energy has been a major concern in those mines that rely on drilling and blasting operation to carry out main production. Due to continually increasing cost, efficient mining demands, and associated hazards of using explosives, it is necessary to utilize explosives at their best. Efficiency of a blasting operation is generally evaluated by the fragmentation size. From post blast conditions at blasting site to efficiency of processing plant, anything can be affected due to improper blast resulting in bad fragmentation. Better fragmentation is necessity for better operation of the system along with consideration of the safety of operation, environmental issues and related costs. For developing a blast design, an engineer should always attempt to minimize the cost of operation without compromising with acceptable technical and safety necessities [1]. Blast performance is dependent on many different factors associated with the process. These factors have been gauged as blast geometry, explosive specification, and rock mass properties [2]. Similarly, in 2013 Mohammad et al. concluded that fragmentation dynamics depends on blast hole diameter, primer, spacing, stemming, burden, and delay timing for blasting operation [1]. At the work site where this study was performed, blast holes were filled by drill cuttings and muds to help in confining gases. In a blast hole, gas confinement helps in better rock fragmentation along with reduced flyrocks. This practice is most common in many countries including Pakistan. Due to lack of homogenized particle size, the effectiveness of confinement is variable and majorly based on the size of stemming. Extremely small sized drill cuttings often result in hole blow out along with flyrocks from the collar. This improper blast energy will result in poor blast, bad impacts on environment, and reduced operational efficiency. In addition to the stemming material, the length of stemming is also a prime consideration. The decrease in stemming length will increase the quantity of explosive in the blast hole and an increase in stemming material generally improves stemming performance.

Jan 1, 2019

By V. R. Spironello

The Bureau of Mines is conducting studies of the slags related to ferrous technology to evaluate acceptable substitutes for the auxiliary flux, mineral fluorspar, in foundry operations. This work is directed toward the Bureau's goal of minimizing the Nation's dependence on scarce and critical minerals Comparative basic practice cupola (18-inch-ID) trials were made to evaluate a waste material called "used potlining," which contains significant levels of fluorine, sodium, and aluminum in various compounds. Used potlining is recovered from alumina reduction cells after its useful life, and was supplied by the Aluminum Co. of America (Alcoa) to the Bureau for evaluation. The material in the lump and pelletized form (with limestone) provided extremely fluid slags based on visual observation during cupola operation. No adverse effects were found on cupola performance, metal and slag chemistry, the environment, or mechanical properties of the castings produced. Fluorine recovery in the slag was equal to, or higher than, that of fluorspar; fluorine losses to the scrubber water and solids were lower. The acidity of the scrubber Hater was somewhat neutralized. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag and visual inspection. The recovery of sodium in the slag, presumably as the oxide, significantly increased slag fluidity, suggesting that less than equivalent fluorine may be required. There was no contamination of the gray iron by the aluminum from the used potlining. Used potlining was completely satisfactory as a substitute for fluorspar in cupola ironmelting.

Jan 1, 1981