Search Documents

By Eli T. Conner

(Wilkes-Barre Meeting, June, 1911.) My connection, under a commission from the Councils and Board of School Control of the city of Scranton, Pa., with a recent investigation of mine-caves and the resultant damages to surface-improvements, has led to the preparation, at the invitation of our Secretary, of the present paper. It is notorious that there are, in the anthracite-fields, frequent subsidences of the surface, due to the removal of the coal beneath. No particular attention is paid to such occurrences, unless they happen to injure surface-improvements. Many caves have happened in Scranton and its vicinity, which have excited but little remark, since they have generally caused no serious damage. In August, 1909, a cave occurred in the Hyde Park section of the city, generally known as the West Side, which nearly destroyed school-house No. 16 and considerable adjacent property. 'Fortunately, there were no pupils in the building at the time; but the thought of the possible result, bad the usual number of pupils and teachers been present, aroused the public to the gravity of the situation; and the School Board employed engineers to investigate the case. Two reports were made by separate sets of engineers, which differed in some particulars. These differences were pointed out in the public press and magnified, and the consequent agitation of the subject was taken tip and greatly exaggerated by some of the metropolitan newspapers, giving to uninformed people the very erroneous impression that the whole city of Scranton was in danger of sinking into the bowels of the earth. All this tended to affect the credit of the city and to depress real-estate values. The matter was considered at a joint meeting of the Board of Trade, the Councils, and the School Board. The Hon. J. Ben. Dimmick, a former Mayor, suggested that it

Sep 1, 1911

By JOHN JERMAIN

In my opinion, the explanation of the fuel-requirements involving the conception of heat available and necessary above a critical temperature, as advanced by Johnson 1 and elaborated by Howe, Raymond and others,2 affords a theoretically correct basis for such an accounting. It is the purpose of this paper to set forth a first crude attempt to construct a formula which shall show quantitatively the relation between the various factors affecting fuel-economy, and afford a means of comparing the enormous amount of data on the fuel-consumption of various blast-furnaces, at various times and under various conditions of operation. I have also applied this formula to a large number. of individual cases, and have, by its means, compared the furnace-practice of several important iron-making districts. II. DERIVATION OF FORMULA FOR FUEL-REQUIREMENTS. The general expression for the fuel-requirements of the blast-furnace, which I believe to be theoretically correct as to form, is as follows Carbon per ton of iron = Heat per ton of iron necessary in hearth above Tc./Heat per pound of carbon available in hearth above Tc. XFactor of rate of driving. +Carbon dissolved by CO2 of flux. +Carbon dissolved incidental to reduction of ore. + Carbon dissolved in pig-iron. (NOTE.-Tc = critical temperature.) Since, according to Johnson's theory, fuel-economy is usually limited by heat available and necessary in the hearth, rather than by the total heat supplied and necessary, we may write Carbon needed in hearth = Hn/Ha in which Hn is the heat per ton of iron necessary in the hearth above some critical temperature, and Ha is the heat per pound of carbon available in the hearth above this same critical tem¬perature. 1 Trans., xxxvi., 454 (1906). 2 Trans, xxxvi., 792 to 798 (1906) ; Trans, xxxvii., 216 to 237 (1907).

May 1, 1911

By M. Kitazume, H. Imai

The deep mixing method was developed in Japan and put into practice in the middle of 1970s. Since then, the wet and dry type methods have been applied for various improvement purposes in Japan. One stork of mixing tool produces a column shape of stabilized soil in a ground. By the series of productions, arbitrary shape of improved ground can be constructed by overlapping each columns. It is specified to complete the overlapping within 24 hours in order to ensure the tight connection of the columns. However, it can not be completed within the specific time in some cases due to bad weather or machine trouble, which causes a cold joint in the improved ground. In this study, the influence of the cold joint to the behavior of the block type improved ground is examined by a series of centrifuging model tests and FEM analyses. It is found that the ground behavior is influenced by the position of the cold joint, where the cold joint at the sea side shows a little influence to the behavior but one at the port side causes large decrease in the stability of the improved ground.

Sep 8, 2021

By Matthias Pulsfort, Hanna Nissen, Markus Herten

An insufficient integrity of cast in-situ bored piles can lead to a reduction of the load bearing capacity and may require cost intensive repairs. Reasons for an insufficient pile integrity are linked to the construction process, mainly to poor concrete quality leading to bleeding and segregation of the fresh concrete. Moreover, the entrapment of soil and an insufficient concrete cover can pose a problem. Knowledge about the time-dependent development of the fresh concrete pressure during the construction process of bored piles is needed for a better understanding of the underlying processes causing these defects. Therefore, pressure measurements were carried out on different construction sites with pressure cells being installed at different depths along the reinforcement cage. The measurements revealed the maximum pressure acting on the surrounding soil. The achievement is a better understanding of the effects of the concrete placement specifically and the construction process in general on the surrounding soil to reduce the risk of pile imperfections.

Sep 8, 2021

By William Billiet

"The Dulles Silver Line Phase II is an 11.4 mile extension of the Washington Area Metro Transit Authority’s Silver line in northern Virginia. There are three miles of elevated guideway, which are supported on 188 large diameter mono-shafts founded within the Triassic Geologic Aged Culpeper Fault Basin. Three lateral load tests were performed on fully instrumented test shafts. The challenge in developing the load testing program was how to reproduce the effects of the extremely high design loads along the test shafts, considering the limitations of the load test equipment. Development, execution, and analysis of the lateral load test program is discussed.INTRODUCTIONPlans for Dulles Silver Line Phase II include two Aerial Guideway sections on elevated track, the Main Line and Yard Leads. The Aerial Guideways are supported on mono-shafts (single, largediameter drilled shafts) socketed into rock. Lateral loads are resisted primarily through the stiffness of the shaft and the geotechnical resistance of the rock socket. The monoshafts were designed in accordance with AASHTO LRFD 2014. Based on our preliminary analyses, the production mono shafts were expected to consist of 6.5, 7.5, and 8.5 foot diameter drilled shafts with rock socket lengths varying between 8 and 34 feet (averaging 14 feet). Table 1 summarizes the maximum service load combinations for each size production shaft along the aerial guideway alignment.GEOLOGYThe project is located within the Piedmont Province, a major physiographic province on the east coast of the USA extending from Alabama to Pennsylvania. Within the Piedmont, a number of Mesozoic basins formed in rift valleys. Dulles Airport is located in the Culpeper Basin, characterized by a relatively shallow siltstone rock surface compared to the adjacent areas underlain by Piedmont crystalline rocks. The geologic stratigraphy at the load test sites generally consist of residual soils and intermediate geo-material (IGM) overlying siltstone rock. IGM is a term used by Virginia Department of Transportation (VDOT) to describe residual material as it transitions between soil and rock. For the purposes of the load test, the siltstone rock is classified as fractured rock (RQD<50), and competent rock (RQD=50). Table 2 summarizes the stratigraphy encountered at each test site."

Jan 1, 2017

By Giulia M. B., Ferruccio Cribari, Alessandro Bertero, Eliano Romani, Roberto Sorge, Francesca Casini

"The use of Artificial Ground Freezing (AGF) to form earth support and seepage control barrier systems has had applications worldwide. These cover a variety of construction problems, including the formation of frozen earth walls to support deep excavations, structural underpinning for foundation improvement, and temporary control of ground water in construction processes. An application of AGF during construction of Line C of Rome underground is described in detail.The new line “C” of San Giovanni metro station was constructed adjacent to the existing line “A” of San Giovanni station; the new metro line “C” is deeper than line “A” and runs below the existing station. The underpass project envisages an Artificial Ground Freezing in order to create a structural and waterproof temporary cut-off suitable to the two new tunnels excavation, while keeping trains running in the safest possible condition. The excavation of tunnels under the water table, with a hydraulic head of over 10 m in not homogeneous soils having different mechanical properties and permeability and below existing sensitive structures, involves special ground freezing sequences and methods, as well as peculiar drilling systems and operations, such as TDDT (Trevi Directional Drilling Technology).Artifical Ground Freezing IntroductionNatural freezing occurs seasonally in many areas of the globe and can affect negatively the engineering performance of geotechnical structures; on the other hand, man-made freezing is a controllable process that can be used by civil engineers to stabilise temporarily the ground in order to support and/or exclude groundwater from an excavation until the final retaining and lining structures are constructed. Freezing and thawing of the pore fluid within soils involve complex thermal, hydraulic and mechanical processes that have significant mutual interactions. For example, phase changes of the pore fluid caused by temperature variations can modify the pore water pressure in the soil, which, in turn, can induce mechanical deformation. At the same time, any changes in the hydraulic and mechanical conditions affect the thermal processes by advection and changes of ice and water contents.An application of AGF which will be presented in the paper, refers to the construction works of Line C of Rome underground. In this case AGF was carried out to provide temporary support during excavation of the two Line C running tunnels directly underneath the existing S. Giovanni station of Line A, in the safest possible condition. In order to keep the trains of Line A operational during excavation, a temporary structure was installed and a real-time monitoring system was conceived in order to control the temperatures of the soil during freezing and the response of the structures of the existing station."

Jan 1, 2016

By Geraldo Lúcio de Faria

Amostras de aço baixo carbono (aço ABNT 1015) foram submetidas a tratamentos termoquímicos de cementação sólida fazendo-se uso de duas fontes distintas de carbono. Amostras do aço foram empacotadas em uma mistura de pós constituída pela fonte de carbono e cal hidratada e tratadas a 1000oC por 8 horas. As fontes avaliadas foram um tipo de carvão vegetal e uma remessa de coque de baixa qualidade metalúrgica. Realizados os tratamentos termoquímicos, as amostras cementadas foram devidamente caracterizadas por microscopia óptica e pela aplicação de ensaios de microdureza Vicker. Duas amostras cementadas foram, na sequência, submetidas a tratamentos térmicos de têmpera em água fazendo-se uso de duas temperaturas de austenitização (860ºC e 920ºC) e também foram caracterizadas. Observou-se que no processo de cementação sólida, a peça cementada com carvão vegetal apresentou melhores resultados do que a cementada com coque de baixa qualidade. Com carvão vegetal, a camada cementada se mostrou mais espessa e homogênea em todo o perímetro das amostras. A amostra cementada com o coque de baixa qualidade apresentou, além da menor espessura de camada cementada, heterogeneidades grosseiras no perímetro da peça.

Oct 30, 2017

By César Yuji Narita

Um dos problemas de aglomerados autorredutores utilizando cimento como aglomerante é a sua baixa resistência mecânica a temperaturas acima de 900°C levando-os à degradação durante a redução. Uma nova tecnologia propôs utilizar as propriedades de plasticidade térmica do carvão fóssil coqueificáveis como aglomerante, o que deu origem ao produto conhecido como CCB (Carbon Composite Iron Ore Hot Briquette). Este trabalho tem como objetivo propor uma rota alternativa para a fabricação dos briquetes autorredutores e estudar o efeito de variáveis de processo na resistência à compressão dos mesmos. O método utilizado na obtenção dos briquetes foi de compactação em matriz cilíndrica de misturas de finos de carvão fóssil coqueificável (log(máxima fluidez) = 2,48) e minério de ferro (pellet feed) seguida de tratamento térmico. Foram realizados testes variando granulometria do carvão, pressão de compactação, taxa de aquecimento e proporção entre carvão e minério e investigados os efeitos dessas variáveis em relação à resistência à compressão e à densidade dos briquetes produzidos. Foi observado que a resistência à compressão obtida nos briquetes produzidos via briquetagem a frio seguida de tratamento térmico são comparáveis com os CCBs.

Aug 1, 2018

By Júlia Beltrami

O trabalho estudou a formação, a interação com a escória e a solidificação de inclusões geradas durante o processamento de aços dual-phase com alto teor de silício (>1%). A composição destes aços, se não bem controlada, pode gerar inclusões sólidas de sílica pura durante o lingotamento contínuo. Para o estudo, foram feitas simulações termodinâmicas com o software computacional FactSage 6.4. As simulações mostraram que os fatores mais importantes para a composição inicial das inclusões é a relação %Mn/%Si e o teor de alumínio dissolvido no aço. Ao interagir com a escória, a tendência é que as inclusões se aproximem da sua composição ao longo do tempo. Durante a solidificação, a maioria das inclusões apresentou fases deformáveis e de baixo ponto de fusão, com exceção das inclusões sem CaO e da inclusão com 25% de Al2O3 e teor intermediário de CaO, que apresentaram as fases tridimita, coríndon e gehlenita de alto ponto de fusão e não-deformáveis.

Aug 16, 2017

By Cermets

Ti(C,N)-based cermets offer good high temperature strength, perfect chemical stability, excellent wear resistance, and relativly better machinability. In the present work, the tribological behaviors of Ti(C,N)/SiC sliding pairs lubricated in water and seawater were evaluated using a ball-on-disk tribometer. The experimental results show that a relatively low friction coefficient (about 0.025) can be obtained when lubricated with artificial seawater at the sliding speed of 200 mm/s, while the date is about 0.2 in purified water. The wear surface profiles and the lubricants collected after running-in process for the high/low friction conditions were compared. In addition, the effect of salt molar concentration of the lubricant on the Ti(C,N)/SiC friction properties was investigated. It was found that the smooth and flat surface is the premise to gain the low friction. At the same time, the proper concentration of silica colloid, which is affected by the salt ions, is also an essential one. Moreover, the high sliding speed (200 mm/s) is beneficial to achieve low friction.

Jul 31, 2018

By Daniele Perondi

Diferentes resíduos são gerados pelas indústrias siderúrgicas, dentre eles o resíduo dos trituradores de sucatas (RTS). O RTS gerado pelas siderúrgicas brasileiras se difere dos demais países devido aos materiais que são alimentados no triturador. Assim, o objetivo deste trabalho foi avaliar as características do RTS gerado por uma siderúrgica brasileira. As seguintes técnicas foram utilizadas: identificação e quantificação dos principais constituintes, análise termogravimétrica, imediata, elementar, poder calorífico superior e teor de cloro e metais. Os principais polímeros presentes no RTS foram o poliestireno e o polietileno. A partir dos resultados de análise imediata, elementar e de poder calorífico superior do RTS, verificou-se uma elevada quantidade de matéria volátil (76,22% ± 6,90). Os altos teores de carbono (72,92%) e hidrogênio (9,86%), foram atribuídos à elevada quantidade de polímeros e borrachas presentes no resíduo. O teor de enxofre (0,21%) pode ser atribuído a presença de borracha no resíduo, enquanto o teor de cloro (1,33% ± 0,13) pode ser atribuído a presença do PVC no resíduo. O poder calorífico superior do RTS foi de 30,01 ± 1,22 MJ/kg, de forma que uma avaliação termoquímica mostra-se como uma técnica atrativa para a sua destinação final.

Oct 30, 2017

By Francisco Belmino Romero, Walney Silva Araújo, Vitória Lima de Souza, Edilberto Rocha Silveira, Adriana de Oliveira Sousa Leite

O uso de inibidores verdes na corrosão do aço carbono SAE J403 1020 configura-se como uma alternativa econômica e ambientalmente acessível, pois, em relação aos inibidores comerciais geralmente utilizados, são de fácil obtenção, já que são adquiridos a partir de vegetais, portanto, não oferecem risco ao meio ambiente. Assim, o presente trabalho tem como objetivo avaliar o uso das folhas de aroeira como inibidor de corrosão para o aço carbono SAE J403 1020, o qual é bastante utilizado na indústria e possui baixa resistência à corrosão. A escolha da aroeira se deu devido ao fato de a planta ter origem no Brasil e abundância no Nordeste do País, principalmente no Ceará. Para análise, foram utilizados como meio corrosivo: H2SO4 0,1 M, NaCl 3,5% e NaCl (ph = 4,0); as concentrações do inibidor foram: 50, 200, 500 e 1000 ppm. Em relação aos ensaios eletroquímicos, utilizou-se: Potencial de Circuito Aberto (OCP), Espectroscopia de Impedância Eletroquímica (EIE) e Curvas de Polarização Linear (CP). Dessa forma, por meio da análise das técnicas mencionadas, conseguiu-se obter o comportamento do inibidor em relação ao material e ao meio, bem como avaliar qual o melhor meio para a utilização da aroeira como inibidor verde de corrosão.

Mar 1, 2019

By F. Ntuli, T. V. Nyangadzayi

Chromium green is an essential metal with various applications in the paints, construction, electronics, and aerospace industries. The main source of chromium green is the carbo-thermic reduction of chromite ores, however, chromite ores are being heavily depleted on a global scale, hence the need to find alternative or secondary sources for the chromium. In order to meet the global demand for chromium there is a need to implement principles of the sustainable circular economy to keep chromium within the material loop. Ferrochrome slag and stainless steel slags are secondary resources that are potential sources of chromium. In this work, recovery of chromium from ferrochrome slag was investigated. The ferrochrome slag was alkaline leached using sodium hydroxide- sodium hypochlorite solution to reduce the use of potent reagents that have a potential negative environmental impact. The leachate produced by oxidative alkaline leaching of ferrochrome slag contained hexavalent chromium, which was used to recover the extracted chromium through a two-stage process involving reduction and precipitation. Reduction of hexavalent Cr to trivalent Cr was investigated using anhydrous FeSO4 at concentrations of 5 g/L, 10 g/L, and 15 g/L. Precipitation was conducted by dosing the reduced leach solution with 1 M sodium hydroxide at dosages of 5 ml/L, 10 ml/L, and 15 ml/L. The experiments were designed using the Taguchi (L9) orthogonal array and analysed according to the ANOVA, general linear model. The optimized conditions for the reduction step were ferrous sulfate dosage of 5 g/L with a pH of 12, and for the precipitation step, 1 M sodium hydroxide at a dosage of 15 ml/L with a setting time of 90 minutes and pH of 7. Physical changes were observed during the two-step chromium recovery, with solution changing from a yellowish colour to dark green colour indicating completion of the reaction. The chromium recovery was found to be 93.3%.

Dec 11, 2024

By L. J. Su, J. Y. Zhang, P. W. Gu, J. F. Xu

Surface tension of mold flux is a key factor affecting optimum casting conditions. A thermodynamic model was developed to determine the surface tension of mold flux containing fluoride based on the ion and molecule coexistence theory of slag structure and Butler’s equation. The relationship between composition and surface tension was investigated by this model. Results indicated that the calculated values showed good agreement with literature data, and the average error was 8.19%. The surface tension value of the CaO–Al2O3-based mold flux was larger than that of the CaO– SiO2-based mold flux. The surface tension in a multi-component system decreased with increasing contents of SiO2, CaF2, and Na2O, which are considered surface-active components. This trend was more significant in the CaO–Al2O3-based mold flux.

Dec 11, 2024

By S France

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will comprise 2.5 km of ‘undrained’ driven tunnels and 900 m of drained cut-and-cover tunnel and portals.The project is aligned beneath a stream valley of Oakley Creek incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The hydrogeology of the area is complex with perched aquifers in compressible soils, cascading water levels in fractured rock aquifers, and discontinuous higher permeability units resulting in artesian water levels and groundwater springs.Numerical groundwater modelling was undertaken to assess the potential effects of tunnel construction and long-term operation on the groundwater system; the magnitude and extent of changes in groundwater level and the resulting potential for settlement, buoyancy effects, contaminant migration and adverse effects on creek base flow. Modelling also provides inputs to tunnel design such as groundwater seepage volumes and water pressures.The driven tunnel will be ‘undrained’ long-term so potential effects on the groundwater system are limited to short-term dewatering during construction. Significant project time and cost savings can be made if the portal areas are permanently ‘drained’, but this means potential effects are greatest in the long term condition.This paper summarises the investigations, implications of the complex hydrogeological setting on tunnel design and environmental assessments, and groundwater modelling undertaken during the planning stage of this project. The groundwater modelling has been used to incorporate mitigation options in tunnel design and construction sequencing; a comprehensive monitoring program will be used to trigger appropriate responses should effects differ from those predicted.

Mar 8, 2011

By R. L. Crosby, L. W. Higley

Magnesium- rich magnesium- aluminum- zirconium alloys in the cast and in the extruded and heat- treated condition were studied to identify the phases present and to determine phase distribution . In cast alloys , two intermetallic compounds were identified : ZrAla by X- ray diffraction ; and Mg₁ Al₁₂ by microscopical observation . Based on microscopical comparisons between the known phases in the cast structures and the phases in the structures of extruded and heat - treated rods , ZrAl₂ and Mg1 , Al12 were identified in the structure of the latter . The presence of these intermetallic compounds in rod specimens could not be confirmed by X- ray diffraction . ZrAl₂ was observed in the structure of extruded and heat - treated rod specimens containing as little as 0.01 weight - percent zirconium . The presence of aluminum restricts the solubility of zirconium in magnesium because of the strong tendency to form ZrAla . This intermetallic compound segregated in clusters of small particles in the matrix of cast alloys , and only slight improvement in distribution was noted when the alloying techniques were varied .

Jan 1, 1964

By J. A. Ruppert, P. M. Sullivan

A study was made of filtration techniques for recovering the major part of the tin contained in iron - tin alloys known as hardhead . Special smallscale filtering apparatus and a three - stage cyclic process were developed . Eighty- seven percent of the tin contained in an alloy of 82 percent tin and 17 percent iron was recovered as pure metal by pressing at 975° C followed by a second pressing at 800 ° C and a final filtering at 250 ° C. Small amounts of Sb , Cu , and Fe impurities were removed by adding Al to the molten product and performing another filtration at 250 ° C.

Jan 1, 1964

By R. E. Lindstrom, D. J. Bauer

Studies were conducted to assess the potential of naphthenic acid as a fractional extractant for rare- earth mixtures and yttrium in sulfate solution . Naphthenic acid was an effective extractant , and separation factors were favorable in the presence of aqueous phase chelating agents . Addition of EDTA to the naphthenic acid extraction system resulted in average separation factors of 2.2 between adjacent yttrium- group elements , whereas DTPA resulted in average separation factors of 3.5 between adjacent cerium- group elements . EDTA was of value in separating yttrium from the rare- earth elements . Thorium and uranium were preferentially extracted over the trivalent rare- earth elements by naphthenic acid .

Jan 1, 1964

By J. C. Meeks, C. L. Klingman

An instrument that is sensitive , portable , safe , and low in cost was developed by the Bureau of Mines for detecting helium leaks by comparing the thermal conductivity and flow rate of the atmosphere around the suspected leak against a reference of helium- free air . A vacuum pump pulls the sample gas through a restriction and over thermistor elements , the combined electrical output of which is affected by thermal conductivity and flow rate of the sample gas . Tests showed that the battery - operated Helium Leak Detector was effective and rugged instrument that could be operated safely in explosive atmospheres . The instrument could also detect , but not identify , other gases such as methane , hydrogen , argon , carbon dioxide , and Freon 12 .

Jan 1, 1964

By F. R. Cattoir, R. E. Cumings

Columbium metal was electrorefined in a fused - salt electrolyte . Excellent results were obtained in lowering the impurity content in a 94 - percent columbium anode feed material to produce a 99.8- percent - pure metal . The reductions of the major impurities follow : Oxygen from 19,800 to 500 ppm , carbon from 9,700 to 25 ppm , iron from 9,200 to 630 ppm , nitrogen from 2,100 to 90 ppm , and silicon from 750 ppm to not detected . Columbium with a purity of 99.9 percent was produced from 99.5- and 99.8 - percent grades of columbium. The investigation was devoted to the evaluation of a fused - fluoride - salt electrolyte ( KF - NaF- K₂ CbF, ) for electrorefining columbium. The effects of the columbium concentration and the voltage upon the product's purity were investigated . The effect on the cathode current efficiency of ampere - hours of deposition and the formation of a dual valence state of the columbium was also investigated .

Jan 1, 1964