Search Documents

By Ke Yang, Kai Zhang, Xiaolou Chi, Xiangyang Zhang, Yingming Li

Based on the research background of 1303 working face return air roadway in Jinyuan Zhaoxian Mine, Shaanxi Province, a method of determining the reasonable spacing of boreholes is proposed based on the stress transfer degree of coal above and between boreholes, combined with the law of plastic zone and energy evolution by theoretical analysis and numerical simulation. After drilling pressure relief, the average daily energy of microseismic events decreased by 70%, and those with microseismic energy greater than 104 J decreased by 99.2%. The research has a strong guiding significance and research value for determining the reasonable distance of borehole pressure relief.

Jun 25, 2024

By Jorge Armstrong, Sean Warren, JOSEF BOURGEOIS

The application of statistical analysis software programs has proven useful for the investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the US National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Jun 18, 2023

By Alistair James, Mo Shahsavari, Leon Botham

The 1889 Johnstown Flood, which killed 2,209 people, was a preventable disaster stemming from systemic decisionmaking failures. This paper applies modern Risk-Informed Decision Making (RIDM) frameworks to analyze the historical context and explore alternative outcomes through hypothetical multiverse scenarios. By reconstructing the risk landscape of the South Fork Dam, we demonstrate how structured hazard identification, risk assessment, and stakeholder communication could have mitigated or prevented the catastrophe. Three counterfactual scenarios—proactive maintenance, community engagement, and regulatory oversight—are evaluated to quantify potential lives saved and economic benefits. The study acknowledges historical barriers, including technological limitations, lack of governance, and socioeconomic disparities, which constrained risk-aware decisions in the 19th century. The analysis draws critical parallels to contemporary engineering challenges, particularly in tailings storage facility (TSF) management, where similar risk blind spots persist. The paper concludes that RIDM is not merely a technical tool but a governance imperative, essential for ethical and sustainable engineering practice. By learning from historical near-misses and failures, the modern engineering community can strengthen resilience and accountability. This work contributes to the growing body of retrospective risk analysis, offering a methodological framework for applying RIDM to historical disasters to inform future safety standards.

Feb 22, 2026

By Jorge Gibson, P. Chris Pistorius, Megha Jampani

Increased utilization of natural gas in blast furnace ironmaking can decrease both the cost and the carbon intensity of ironmaking, given current US natural gas prices. In this paper, three ways to utilize natural gas are compared: tuyère injection, prereduction of iron ore, and shaft injection. The basis for comparison includes coke replacement ratios, carbon intensity and furnace productivity. These were calculated using relevant mass and energy balances, a blast furnace productivity correlation based on the bosh gas flow rate, and measured and modeled prereduction kinetics. Of the natural gas utilization methods, prereduction has the highest effective coke replacement ratio (and hence the largest advantage in raw material cost), but is likely to have the highest capital requirement.

Mar 1, 2017

By Qingguo Xue, Jingsong Wang, Guang Wang, Yuanyuan Zhang

Due to complicated structure and composition of high-phosphorus iron ore, pure substances were used to simulate the chemical composition of high-phosphorus iron ore to study the reaction of fluorapatite at different temperatures and effect of additives. The gasification process of P during carbothermic reduction process was investigated using a quadrupole mass spectrometer gas analysis. It is found fluorapatite was reduced to phosphorus which diffused into iron and gas phase. From the gas analysis, it was observed that PO and P gas species were vaporized around 800 °C. As the reduction temperature increased, the diffusion of phosphorus into iron was enhanced. The presence of Ca(OH)2 as additives not only promoted the reduction of iron oxide, but also decreased the degree of fluorapatite reaction to inhibit P into iron.

Mar 1, 2018

By A. Yudiarto, M. Z. Mubarok

At the present paper, synthesis of magnesia from ferronickel smelting slag is discussed. The first stage was extracting magnesium from the slag by leaching in HCl solution. Magnesium extraction of 97% was obtained from the slag leaching with HCl 8 molar, solid:liquid ratio 1:40 (g/ml) and temperature 80 °C after 24 h. Solution purification was performed by adjusting solution’s pH at 95 °C with addition of MgO powder. At pH range range of 3–4, co-dissolved iron was removed as akagenite (b-FeOOH) precipitate. Dissolved nickel precipitation was detected at pH range of 4–6, while dissolved Mg and Al started to precipitate in the forms of pyroaurite (Mg6Fe2CO3(OH)16∙4H2O) and hydrotalcite (Mg6Al2CO3(OH)16∙4H2O) at pH range of 8–9. High purity of brucite (Mg(OH)2) was obtained by Mg precipitation at pH range of 11–12, under stirring speed of 300 rpm and stirring time of 4 h. Calcination of brucite at temperature of 1000 °C completely converted brucite to periclase (MgO) powder after 240 min.

Mar 1, 2017

By Vahid Javaheri, David Porter, Tun Tun Nyo

A field emission scanning electron microscope equipped with EBSD has been employed to evaluate the role of 0.013 wt% Nb on the evolution of the microstructure and texture of a novel thermomechanically processed low-alloy, medium-carbon steel. Specimens were subjected to hot-rolling with a total reduction of 80%, four passes in the recrystallization regime and four passes below the non-recrystallization temperature. Immediately after rolling, the strips were quenched to 420 °C and subsequently cooled slowly in a furnace to simulate strip coiling with transformation of austenite to bainite. The results showed that Nb microalloying results in a finer microstructure with a sharper texture when compared to an identical steel but without Nb. In addition, analysis of the retained austenite texture indicated that the main bcc texture components are the product transformed brass and copper components in the parent austenite.

Mar 1, 2018

By Ruari Soutar-Dawson, Fisher Wang, Alan Boylston, Michael Denzel

Vertical stirred mills are increasingly used for fine grinding applications in the mineral processing industry due to their high energy efficiency. Thus, modeling power draw is of great interest proven by the effort in previous work including analytical models. In this contribution the development of a DEM-CFD coupled model is presented to determine power draw under different operating conditions. These include grinding media filling level, shaft speed and fluidization as well as changes in grinding compartment configuration. An extensive test program on an especially equipped test mill is initiated to validate the model.

Feb 22, 2026

By Nadia H. Rafat, Iman S. El-Mahallawi, Hussein Badr, N. Khattab, Ahmed A. Abdel-Rehim

The basic part of solar water heaters is the collector and the main functional part of the collector is the absorber layer. In this work, a commercial locally available black painting (PACEN code 10382 colour 890), used for swimming pools solar heating, was modified by adding nano-graphite dispersion. The effect of nano-graphite particles percentage on the spectral absorbance of the material was examined on samples containing two values of 1.5 and 2.5% nano-graphite particles by weight. Fourier transform spectroscopy (FTIR) analysis was also used to identify the functional groups in the developed material. A simple experimental setup was designed to evaluate the performance of the developed nanodispersed selective coating polymeric based material, by measuring the increase in temperature of circulating water. It was shown that adding 1.5–2.5% nano-graphite particles to a polymer based black coating causes an increase in the optical absorptance, and an increase in the circulating water temperature.

Mar 1, 2018

By C. N. Eze, C. K. Ezeh, O. Nnabuife, N. M. Ugwoju, S. C. Enemuor, V. Okechukwu

In this study, the efficacy of Providencia vermicola KUBT-1 in the leaching and beneficiation of Agbaja iron ore was evaluated under varying conditions of temperature, ore particle size, and pH. Agbaja iron ore is a Nigerian low-grade ore containing about 43%–52% iron and a high amount of gangue materials, including phosphorus (1.4%–2.0%) and sulphur (0.12%). The study was organised in triplicate in shake flasks with 48 samples. One millilitre of washed cells of Providencia vermicola KUBT-1 suspended in normal saline at 0.5 McFarland standard (108 cells ml-1) was introduced into each flask containing 50 g of sterilised ore in 100 ml of bioleaching medium, and the samples incubated at room temperature for eight weeks. The levels of upgraded iron, mobilised sulphur, and phosphorus were determined by atomic absorption and ultraviolet spectrophotometric analyses, respectively. Results showed that a particle size of 0.8 mm was optimal for iron upgrading and sulphur mobilisation while 1.0 mm ore size was optimal for phosphorus mobilisation. Up to 89.60% of the iron was upgraded while phosphorus and sulphur were mobilised, leaving residual values of 0.223% and 0.02%, in the ore, respectively. The organism produced best beneficiation results at a pH of 2.5 and a temperature of 3ºC. Correlation analysis with the Pearson’s correlation model showed a positive correlation between iron upgrading and sulphur-phosphorus removal (r =1.000, and r =0.967), respectively. These results present Providencia vermicola KUBT-1 as a promising candidate for large scale leaching and beneficiation of Agbaja iron ore.

Dec 15, 2025

By L. Escudero-Castejon, S. Sanchez-Segado, A. Jha, Y. Hara, S. Parirenyatwa

In a world where declining ore grades are increasingly common, it has become necessary to process low-grade feedstock. Carbothermic reduction in the presence of alkali (Na2CO3) has been adapted to beneficiate waste that contains titaniferous minerals (TiO2 ca. 12 wt%), in order to recover valuable constituents such as TiO2, Fe and V2O5. The waste from vanadium metal processing has environmental legacy as it leaves nearly 1 wt% V2O5 process waste, which is environmentally problematic due to V5+ ions in contact with water and soil. This investigation focuses on the kinetics and mechanism for alkali reduction of mineral waste bearing 10–12 wt% TiO2, which we studied in the 1073–1323 K range. The thermogravimetric analysis (TGA) technique was used to record weight loss data. Two distinct regimes demonstrated mixed-control kinetics: (1) at low temperatures the activation energy was found to be 199 kJ mol−1, which corresponds to the outward diffusion of O2− ions; and (2) at high temperatures the calculated value was 130 kJ mol−1, which is consistent with the activation energy for the outward diffusion of Fe2+ ions. The metallic iron, sodium titanate and sodium aluminosilicate phases that formed were characterised using X-ray powder diffraction (XPRD) and scanning electron microscopy (SEM) techniques, and their significance for metal recovery is explained.

Mar 1, 2017

By Liuyin Shi, Kang Liu, Fengqi Zhao, Yan Song, Zhiping Yang, Xing Fan

Due to the high energy consumption, long technical process, low usage rate of vanadium during the traditional smelting vanadium steel process, a new method for decarburization by CO2 to directly smelt vanadium-containing steel in blast furnace was proposed. In this paper, the thermodynamics of CO2 decarburization in molten iron process was calculated out by FactSage. The thermodynamic calculations indicated that in standard state, the transformation temperature of C and V was 1357 °C; the oxidation order of element was Si, C, V, Mn and S when using CO2 as oxidant. The experiment of blowing CO2 temperature showed that decarburization reaction temperature was 1550 °C, carbon content could be decreased to 0.676%, the decarburization rate was 88%. There was no effect on vanadium content in molten iron during the decarburization process, vanadium content was 0.323%, which meets the request of vanadium mould steel.

Mar 1, 2018

By Scott O’Brien, Richard Williams, Camilo I. Mejias, Elias Godoy, Javier Sierra

High-rate thickeners play a critical role in tailings management by enhancing water recovery and increasing solids concentration. However, these units face operational instability due to fluctuations in feed solids, flow rate, and flocculant response typically managed in manual mode with delayed corrective actions. This work presents an adaptive automatic control algorithm designed for dynamic thickening environments. The algorithm integrates real-time measurements of feed density, rake torque, bed level, and turbidity (overflow), optimizing the underflow slurry density while minimizing suspended solids in the overflow. The proposed control strategy is modular, simple, scalable, and applicable to both existing and new thickening systems, offering a robust alternative to manual operation in increasingly demanding metallurgical environments.

Feb 22, 2026

By C. H. Stephenson, M. Du Preez

Overland belt conveyors often use vertically guided counterweight take-ups or horizontally tensioned carriages to maintain belt tension. In the event of belt or wire rope failure, these systems can release significant stored energy, creating high-impact forces that risk structural damage and personnel injury. This paper reviews current safety arresting technologies and presents a calculation methodology for estimating impact velocity, energy absorption requirements, and stroke limitations. Worked examples illustrate the selection process for appropriate arrestor types under different design constraints. The study emphasizes early integration of safety devices to minimize structural loads, avoid costly retrofits, and enhance operational reliability. Implementing robust arrestor systems improves safety and reduces downtime in bulk material handling environments.

Feb 22, 2026

By Konstantinos Salonitis, Joanna Mielnicka, Mark Jolly, Arun Prabhakar

Lead sheets are widely used for roofing applications, radiation protection and sound proofing. Most of the sheets are either produced by rolling cast slabs of lead sheets or via the direct method (DM) of casting of the sheet continuously. The DM method comprises of a rotating water-cooled drum that is partly immersed in a bath of molten lead and sheets are cast out continuously. The direct method of casting lead is more energy efficient compared to the rolling process which requires a casting process before rolling to achieve the required thickness. This work investigates the energy consumption in different stages of the DM process and suggests pointers for improvement. An energy audit of the process is conducted and the consumption is analysed at different stages and compared with rolled lead.

Mar 1, 2018

By Beatryz C. Mendes, Igor K. R. Andrade, Roseli O. G. Martins, Gustavo H. Nalon, Rita de C. S. S. Alvarenga, Leonardo G. Pedroti, Carol F. R. Santos, Marcelo A. Alves

This work presents an experimental investigation of the influence of concrete blocks and mortar’s compressive strength on the flexural bond strength, normal to the bed joints, of concrete structural masonry. Third-point beam tests were performed on concrete prisms, considering two different kinds of concrete blocks (compressive strength of 5.9 and 8.2 MPa) and six different cement-lime mortar compositions (compressive strength around 30, 70, and 120% of the blocks’ net area compressive strength). Units’ absorption and mortar’s initial flow and water retentivity were not varied, but remained within the suitable range for use in structural masonry. For both types of concrete blocks, it was observed an increase on the prism’s flexural bond strength with the increase of the mortars’ compressive strength. A lower mortar’s water-cement ratio led to higher bond strength. When fixing the ratio between mortar’s and concrete block’s compressive strength, it was noticed that the increase on the blocks’ strength contributed to a slight increase on the masonry’s flexural bond strength, except when using high strength mortar, in which the increase was significantly greater.

Mar 1, 2018

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By F. Guo

"The leaching kinetics of zinc sulphide concentrate was studied under total pressures ranging from 0.3 MPa to 0.5 MPa and leaching temperatures ranging from 358 K to 378 K. The apparent activation energy of leaching reaction under different total pressures was calculated. The results show that for the extraction of zinc at low-temperature pressure leaching is controlled by an interfacial chemical reaction. This was supported mineralogical analysis of the leaching residue. The kinetic equation for low-temperature pressure leaching of zinc sulphide concentrate was further established by quadratic regression on the basis of shrinking core model.INTRODUCTIONThe Roast-Leach-Electrowinning Process (RLE) is the primary route for zinc production and responsible for more than 85% of the total zinc production (Souza et al., 2007). During the roasting of zinc concentrates, fugitive SO2 causes pollution. The prevention of SO2 emissions from the RLE process can be one of the challenges to this technology (Deller, 2005). In the 1980s, the Zinc Pressure Leach (ZPL) process changed the concept of zinc hydrometallurgy, in which zinc sulphide concentrate is directly leached at approximately 423 K and approximately 0.7 MPa oxygen overpressure and the sulphidic sulphur is oxidized into elemental sulphur so that the pollution by SO2 is completely avoided. Since 1981, five zinc plants have adopted the ZPL process either for expansion by integration with existing roasting facilities, or for the production of zinc without any roasting at all (Collins et al. 1994; Barth et al. 1998). The innovation of the ZPL process has made the zinc industries more competitive although it needs an autoclave. The direct leaching technology of zinc is still in development."

Jan 1, 2012

By C. Newman, R. C. Ray

Originated and developed in the civil tunneling industry, the Ground Reaction Curve (GRC) has provided a robust methodology for evaluating and designing ground support in both tunnels and underground mining scenarios. This paper presents a preliminary assessment in the utilization of the GRC concept for the evaluation and design of the pillar-support system with respect to overburden stress and displacement. This initial assessment will be based on and backed by past research on this topic. Underground mine instrumentation is planned for a longwall mine in the Appalachian coal field based on the research and findings in this paper to support the postulated hypothesis. INTRODUCTION Since the early 1970’s, the mining industry has evaluated the structural stability of a pillar by dividing an approximated pillar load by an approximated pillar strength. While this design methodology has served the industry well in the past, as modern mining operations continue to develop in more complex geological and geometric conditions coupled with market economics, industry professionals are in dire need of a modified stability assessment approach which considers both the stress condition and material displacements. Within the civil tunneling industry, the GRC approach has been successfully utilized in designing underground support measures that enhance the stability of an underground excavation. Through the incorporation of current industry knowledge and understanding of ground and support behaviors this paper looks to investigate into preliminary assessment for the development of a Modified Support Response Method (MSRM) to further improve the analysis of local and global underground stability. CURRENT PILLAR DESIGN METHODS AND THEIR LIMITATIONS Globally, multiple pillar design methods have been utilized in the design of underground excavations. Each of these methods approaches the calculation of pillar stability a little differently with respect to material properties, underground geometries and stress conditions. Analytical solutions can be used to determine the strength of homogeneous materials like concrete, but not in case of non-homogeneous and non-isotropic mineral deposits in a mine. These equations are often derived using empirical methods. Pillar strength is defined as the maximum resistance of a pillar to axial loading (Brady & Brown, 1985). The strength of mine pillars is typically estimated through indirect methods. In the past, researchers have correlated the strength of a given size and width of a rock specimen to the strength of a mine pillar. The first study on the effect of geometry on rock strength was done by (Bauschiger, 1876) on Swiss sandstone samples. Since then several empirical equations to determine pillar strength had been published by many researchers like (Bunting, 1911), (Griffith & Conner, 1912), (Greenwald, Howarth, & Hartmann, 1939), (Holland & Gaddy, 1957), (Evana, Pomeroy, & Berenbaum, 1961) and (Holland C. , 1964).

Jan 1, 2019