Search Documents

By Steven George Jansto

The hot ductility behavior of different microalloyed steel chemical compositions was examined simulating the thermal and strain conditions through the straightening or unbending section of the continuous casting machine. All samples were obtained from industrial slab casters ranging from 200 to 300 mm in slab thickness from steel mills throughout the world including China, Brazil, North America and Europe. The slabs were crack-free and hot rolled into prime quality products. No laboratory heats were tested. Although these microalloyed steels exhibit inherently lower hot ductility behavior, as measured by percent reduction in area at elevated temperature, these steels still exhibit sufficient ductility to satisfactorily meet the unbending stress and strain gradients existing in the straightening section of most casters. The majority of the published hot ductility data, as measured by % reduction in area (%RA), were based on laboratory heats and hence, are inaccurate in accessing the propensity for slab cracking on an industrial caster. This situation then results in invalid conclusions for different chemistries. This research has determined the minimum required %RA for crack-free casting is significantly lower than results based upon previously published laboratory generated data. For example, the literature quotes 40% RA minimum for Nb-bearing steels when in fact as low as 10% minimum RA is more than sufficient to assure crack-free casting based upon the extensive testing and analysis performed in this study. Instead of %RA, the measurement of strain energy has been introduced to evaluate hot ductility behavior. It is concluded that strain energy is a better measure of hot ductility behaviour than %RA. There is considerable value in the evaluation of the hot stress and strain curves, process metallurgy parameters and their relationship to slab quality instead of just basing hot ductility decisions on simple %RA measurements.

Aug 16, 2017

By Margareth Almeida Dellamore Pacheco

Devido à carência de tarugos de alumínio 6060 com boa qualidade e baixo custo de produção no mercado de extrusão do Brasil, surge a necessidade de encontrar soluções práticas que resultem em um melhor desempenho das ligas na indústria da extrusão. Este trabalho, portanto, tem o objetivo de estudar a influência do tratamento térmico de homogeneização e da taxa de resfriamento pós-tratamento na microestrutura de uma liga de alumínio 6060, assim como as suas implicações na indústria de extrusão. Tarugos cilíndricos da liga de alumínio 6060, com diâmetro de sete polegadas, foram fabricados e submetidos a diferentes ciclos de tratamentos térmicos em um forno industrial do tipo bambury com a finalidade de dissolver e homogeneizar as partículas de segunda fase na matriz de alumínio. As variáveis de tratamento térmico investigadas neste estudo foram o tempo de residência e a taxa de resfriamento. Os tarugos termicamente tratados foram, em seguida, amostrados para caracterização microestrutural e para a execução de testes industriais de extrusão. Os resultados obtidos indicaram que existe uma significativa diferença microestrutural entre as amostras, que consistiu principalmente na variação das frações de precipitados de Mg2Si na matriz. Foi possível concluir que a produtividade na extrusão depende fortemente da fração desses precipitados.

Aug 16, 2017

By Ana Maria Guilherme Bailon

As fases microestruturais formadas em pelotas de minério de ferro queimadas relacionam-se às características mineralógicas do pellet feed utilizado e determinam propriedades como resistência física e comportamento metalúrgico do material. O presente trabalho objetiva detectar e quantificar fases microestruturais formadas em pelotas submetidas a diferentes níveis de sinterização, bem como sua relação com a resistência à compressão do aglomerado. Para isto foram interrompidas queimas em Pot Grate, gerando amostras de pelotas queimadas contendo fases características de diferentes temperaturas. Pelotas cruas foram submetidas à análise termogravimétrica para avaliação da perda de água dispersa entre os grãos do minério e da água combinada com o ferro em forma de partículas hidratadas.

Aug 16, 2017

By Heidy de Oliveira Simões

O objetivo deste trabalho foi estudar as correlações entre o IPM (Índice de Permeabilidade Magnética) das pelotas queimadas, as trincas formadas durante o processamento das pelotas no pelotamento/endurecimento e o FeO de cada amostra. As análises evidenciaram que o tipo de trinca presente na pelota impacta no IPM fazendo diminuir a correlação entre IPM e FeO. O entendimento do fenômeno possibilitou desenvolver uma metodologia para determinação de um parâmetro que pudesse ser correlacionado ao FeO das pelotas de minério de ferro, estendendo sua aplicação ao pellet feed, baseado nas propriedades magnéticas do material. O método consiste em medir a variação da indutância de um solenoide, provocada pela introdução do material que se deseja determinar o parâmetro no núcleo de uma bobina, determinando-se relativamente a permeabilidade magnética das pelotas e pellet feed. Para tal, foi definida uma metodologia nas quais alterações devidas à variação da densidade da amostra, causadas principalmente devido a trincas nas pelotas, sejam mitigadas, garantindo a repetibilidade dos resultados. Assim, foi possível a determinação do FeO das amostras através da medição deste novo parâmetro, de forma mais rápida, fácil e com um custo consideravelmente menor que na química analítica clássica.

Aug 1, 2018

By Bruna Goulart Bartosiaki

A fabricação de aços com elevada qualidade interna esta correlacionada diretamente ao entendimento de como inclusões não-metálicas se comportam ao longo de cada etapa do processo. Neste estudo, amostras de aço foram coletadas em uma planta industrial, logo após o vazamento e ao final do tratamento em forno-panela, e submetidas à análise via MEV/EDS automatizado. A evolução da composição química das inclusões nas amostras foi representada sob a forma de diagramas ternários e remetida as suas morfologias. A análise automatizada permite a obtenção de dados estatísticos das inclusões varridas, que compreendem faixas de tamanho, número de inclusões e composição química média. Verificou-se que, dependendo dos desoxidantes utilizados e da oferta de oxigênio no banho, ocorrem diferentes morfologias de inclusões. Inicialmente, as inclusões formadas encontram-se na faixa de composição rica em alumina e, à medida que o banho é submetido à agitação, há a modificação da sua composição química para faixas ricas em CaO e SiO2. Durante esta etapa ocorre a redução na população de inclusões, já que inclusões aluminosas são ricas em fase sólida, o que facilita sua remoção, além disso, a agitação do banho favorece a interação entre as próprias inclusões. O comparativo entre a caracterização das inclusões e os parâmetros do processo, durante o refino secundário, permitiu verificar como cada variável contribui para o controle inclusionário.

Jul 30, 2018

By Juno Gallego

A soldagem de peças de aço por arco submerso é um dos processos mais tradicionalmente usados na fabricação de componentes estruturais. A microestrutura do metal de solda é importante na definição das suas propriedades mecânicas, sendo a ferrita acicular um microconstituinte capaz de conferir à solda altos níveis de resistência mecânica e tenacidade. A nucleação da ferrita acicular depende da presença de inclusões não metálicas no metal de solda. No presente trabalho fez-se a caracterização microestrutural do metal de solda preparados com diferentes aportes térmicos. Lâminas finas foram observadas por microscopia eletrônica de transmissão, que possibilitou determinar alguns parâmetros morfológicos e químicos das partículas e a sua relação com a nucleação das ripas de ferrita acicular. Verificou-se que partículas irregulares com maior tamanho, mais ricas em titânio quando formadas com maior energia de soldagem, apresentam maior probabilidade de servirem como sítio preferencial para nucleação da ferrita acicular, se comparadas às partículas mais lisas e menores.

Aug 7, 2018

By Bruna Goulart Bartosiaki

O atingimento de limpeza inclusionária está ligado ao entendimento de como cada etapa de processamento de aços influenciam no comportamento inclusionário. Neste estudo, retiraram-se amostras de aço antes e após o tratamento a vácuo e no distribuidor do lingotamento contínuo em uma planta siderúrgica. As amostras foram submetidas à análise via MEV/EDS automatizado e a medições de oxigênio total. O posicionamento da composição química das inclusões varridas em diagramas ternários remetidas à análise de suas morfologias, bem como a correlação do nível inclusionário com parâmetros de processo e de escórias, possibilitou o entendimento de como as inclusões se comportam. A forte agitação promovida pelo desgaseificador aumenta as interações entre banho, escória e inclusões, de modo que o conteúdo de CaO e de SiO2 nas inclusões aumenta. A transferência de elementos da escória para as inclusões por intermédio do banho é acentuado, fato observado pela geração de espinélios (MgO.Al2O3) ao final do processo. De modo geral, observou-se que além do efeito do abaixamento da temperatura na geração de novas inclusões, o fator reoxidação deve ser levado em conta. Em contrapartida, há a diminuição nos níveis de inclusões maiores desde o início do tratamento em vácuo até o distribuidor. O objetivo deste estudo foi verificar como ocorre a remoção, tratamento e modificação das inclusões nas etapas finais de processamento em aciaria.

Jul 30, 2018

By James A. Finch, Xiang Zhou, Yue Hua Tan

Methods to determine frother functions, control of bubble size and froth properties, are now widely used. Some collectors also exhibit frother functions which are less understood. Using a water-air system in a mini-mechanical flotation cell setup, this paper determines bubble size and water overflow rate for three amine collectors: one primary amine (dodecylamine, DDA) and two commercial ether amines (Flotigam® EDA and Flotigam® 2835-2L) and their combination with two common frothers, MIBC (methyl isobutyl carbinol) and PPG 425 (polypropylene glycol, molecule weight 425). Compared to the frothers, the amines were less effective in reducing bubble size, giving larger minimum size and the two commercial amines showed evidence of coalescence at low concentration. In blends, at fixed frother dosage, frother eliminated the coalescence but as amine concentration increased the amines dominated bubble size. Water overflow was a strong function of reagent type. For fixed 1-cm froth depth, PPG 425, Flotigam® 2835-2L and to a lesser extent DDA produced overflow while MIBC and Flotigam® EDA did not. In blends with frother overflow increased except with Flotigam® EDA. Mechanisms are briefly explored. The principal benefit of blending identified is the elimination of coalescence if residual concentration of the two commercial amines is below ca. 10 ppm.

By E. P. Youngman

Except possibly by individual natives and Liberians (small specters), is now being carried on in Liberia, according to a late report. definite information is obtainable with respect to the mineral resources of e country, except that iron ores are said to be abundant. Tin, copper, zinc, site, corundum, lead, bitumen or li nite, and diamonds have all been re- parte, but no commercial Geposits are known to have, been found. Gold has been duce, but not in significant amounts, as may be inferred from the customs - rt for Liberia recording the exportation of gold to the value of $4.80 Germany from the port of Cape Mount in 1925. It is not uncommon for atives to come into towns with African gold and valuable minerals, but they e reluctant to sive information concerning then. Some years ago the Liberian Government was seeing a loan in return for oil concessions, but apparently no drilling bea boon don

Jun 1, 1932

By M. Peters, P. Schmäh

The development of renewable energies and a sustainable power grid are the challenges for future energy supply. Underground cables will replace the vulnerable overhead lines, because of their safety benefits. Due to the public environmental awareness, smart tunnelling and trenchless solutions are required for inner-city and cross-country installations of underground cables, as well as for crossings and the landfall sections to connect offshore wind farms to the transmission grid. Methods from the tunnelling and pipeline industry provide a high flexibility in the planning of alignments, including versatile tunnel concepts and the installation of protective pipes with E-Power Pipe and Direct Pipe.

Jun 13, 2023

By Enrico Pavese, Tim Kearney, Stefan Lemke

Watertightness is of central importance in hydraulic and underground structures but has always been associated with a risk, as demonstrated by the very high impact that water inflows have on the damage of linings and infrastructure (Howard, 1991; Sandrone and Labiouse, 2011). Concrete is vulnerable to groundwater and chemical contaminants in the soil. These can leach into the pores and cracks of the concrete and degrade its integrity, causing spalling and corroding the reinforcing steel. Moisture migrating into the building can also degrade structural elements over time and lead to mold and other hazards to occupants’ health. In this connection, the demands placed on the setup and detailed design of the seal depending on the negative influence by water on the one hand and on the other hand on the function of a construction in view to its watertightness classification. Thus, the reliable functioning of a seal is of particular significance in the case of traffic tunnels, which are not easily accessible for all subsequent repairs after the construction in seepage water and especially when located in a pressure water zone (risk–cost assessment). Requirements for the long-term efficiency and quality of underground structures have increased in recent decades. Today, the standard lifetime requirement for an underground infrastructure project is 100 to 120 years and, in some cases, even higher. This calls for high increased attention to the durability of the whole structure and of each individual element. Standards, which started as application guidelines given by the manufacturers, are available in the market since the 1980s and are constantly adapted to the current developments in various technical committees. Differentiations are made between: Manufactures application guidelines, case studies or published articles Test standards for the laboratory to guideline the testing procedures (air temperature, type of test equipment, dimensions, test speed, test duration, concentration, type of liquids, monitoring, tolerances, interpretation of results, documentation, etc.), developed by committees based on material and laboratory experts Application standards, which include test standards but also the related minimum performance requirements (values) for material, processing, and quality assurance (practical tolerances), developed by committees based on a wide range of experts (e.g., designers, construction companies, applicators, manufactures, owners, test institutes, quality engineers) and therefore also based on a wide field of experience, different views and up-dated case studies. In the following there are some examples of guidelines and published information’s, ranked according to the year of issue, which are relevant for the development of waterproofing specifications in the tunnel industry:

Jun 13, 2023

By Scott Turner

I have been asked to speak briefly about recent progress in the mining industry of the United States, and to touch on the general advancement of en- gineering science as applied to mining. By recent, I shall mean within the past 20 or 30 years. Such a period includes a great many of the changes which are of particular interest to the present generation of engineers, and the undergraduates of today will hardly turn back farther than the beginning of the present century in their study of develop- ment of methods and processes. Also, my own professional life spans this period, and I have seen or have been aware of most of these developments as they were taking place. In my review of developments, for the sake of simplicity and clarity, I shall deal separately with improvements in metal mining, coal mining, mechanical and electrical machinery for mines, metallurgy, petroleum engineering, and safety practices. Under each of these headings I have set down what appear to me to be the outstanding changes brought about during the past 2 or 3 decades. Other points will occur to other engineers; I do not represent that the following re- view is complete; it is only intended to be suggestive. In general, improvements in mining and metallurgical practices have come gradually, the charges being effected little by little, simultaneously in widely scattered places, and through the experience and inventive genius of many men. These changes have has small beginnings, and are generally the cumulative result of many steady and unsensational progressions, which still continue. What we today might be inclined to consider the culmination of a series of betterments in mining is, of course, but an instantaneous phase of developments which will continue in the future at even a more rapid pace than they have in the past. We are looking at but a flesh of a moving picture, with an endless reel to come after we finally leave the theatre. Behind all the changes in the mineral industry, the driving force has been the increasing demand of an expanding population for more metals and minerals with which to advance civilization. More people, with an increasing per capita consumption, together with the exhaustion of the richer but smaller, and more

Oct 1, 1930

By S. H. Ash

Unusual mining conditions prevail in the State of Washington because the majority of the coal seams lie on extra steep dips, and the roof and floor of the seams are of such a character as to require an excessive amount of timber- ing. The seams as a rule give off a considerable amount of methane, which makes good ventilation imperative. Due to physical conditions, supervision is costly and travel about the workings is difficult. Because of the facts stated, the accident rate has been above the average, and for some time considerable thought has been given the idea of making promotion of safety in and about the mines a responsibility to be shared equally by the employees and the management. With this idea in mind the legislature of the State of Washington, turing March, 1927, passed laws providing that safety committees be selected to function at the coal mines of the State and at the same time recognizing the fact that first-aid education is an integral part of any safety movement; legislation was passed making it mandatory to have all persons in and about the ines trained in first-aid administration. The provisions of the State mining law3 are as follows: "In every mine a general safety committee shall be selected, composed of the mine superintendent or manager of mines, one man selected by the employees or any association of employees in or around said mine, and a third member selected by these two. "The general safety committee shall elect one of the members to act as chairman and one to act as secretary. The duties of the chairman shall be to preside at all meetings of the general safety committee, enforce its rules and regulations and see that its business is conducted in a prompt and business-like manner. The secretary shall keep an accurate written record of the proceedings of all meetings, conduct its correspondence and post notices of regular and special meetings and other matters pertaining to safety. The duties of the general safety committee shall be to investigate all serious and fatal accidents; make bi-monthly.

Jun 1, 1930

By Paul M. Tyler

Syria is a federation of States under French mandate , comprising the Republic of Syria , the Lebanese Republic or Great Lebanon ( Grand Liban ) , the State of the Alouites , and the Djebel Druse Territory . Beirut is the center of government for the whole area , about 60,000 square miles . Syria is essentially an agricultural country . There is little manufacturing ; and with the exception of the production of asphalt and salt , the mineral industries have not yet risen to commercial importance . Whether this condition is due to a dearth of workable deposits or merely to insufficient exploration is not apparent . The mineral resources , as reported by various authorities , include asbestos , asphalt rock , bitumen , chromite , coal , copper , gold , gypsum , iron , lead , magnesite , manganese , marble and other building stones , nickel , ocher , pandermite ( a hydrous borate of calcium) , petroleum , phosphate rock , pyrite , salt , silver , sulphur , tin , and titanium ( ilmenitic beach sands ) .

Mar 1, 1933

By E. P. Youngman

The basic mining law of Esthonia is the law that was passed by the Parliament (Riigikogu), or State Assembly, on March 17, 1927 (effective Avril 1, 1927), superseding the Russian Mining Law Book VII of the Code) issued in 1912. References in this digest are only to articles of the Law of Merch 17, 1927. However, the law concerning all industrial enterprises (Riigi Teataja No. 28, 1920, Law No. 106) governs not only mills and refineries but also mining operations themselves (arts. 2 and 3). No access was ad to that law. Esthonia is not well supplied with minerals; its industries are primari- ly agriculture and dairy farming. Natural gas, prites, lead, zinc, iron ore, salt, and mineral waters have been found but never as yet in deposits of commer cial size. The production of oil shale is of some importance; and peat, which covers as much as 5 per cent of the total area of the country, is mined in sub- stantial quantities. Cement rock, gypsum, fire clay, and phosphate rock likewise are produced, though only on a small scale.

May 1, 1930

By Bin Zhu, Mingmei Zhu, Hong Zhou, Xiaofei Dou, Bin Xie, Yu Wang, Tiancheng Lin

In this study, the formation of 2CaO·SiO2 and 3CaO·P2O5 solid solution (nC2S-C3P) in hot metal dephosphorization process is discussed. The variations of CaO and SiO2 mass, both in nC2S-C3P solid solution phase and liquid slag phase with increasing P2O5 mass in CaO-SiO2-FetO-P2O5 slags were calculated using Factsage software. CaO-SiO2-FeOt-P2O5 slag containing up to 18 % P2O5 was melted at 1823 K then cooled to 1673 K. The contents of CaO and SiO2 both in the solid solution phase and liquid slag phase of quenched samples were observed and analyzed by SEM/EDS. Both the calculated and experimental results show that the contents of CaO and SiO2 in the solid solution phase decreased, just opposite in the liquid slag phase, with increasing P2O5 content in the slags. Formation mechanism of nC2S-C3P solid solution in the slags was derived based on the ionic structure theory of molten slag. The SiO4 4- in the nC2S-C3P solid solution can be replaced by PO4 3- in the liquid phase resulting in the increasing of free Ca2+ and SiO4 4- in liquid phase.

Jan 1, 2015

By Yousef Mohassab, Manoranjan Misra, Monalisa Panda, Eman Wahbah

This work studies the removal of arsenic (V), arsenate, and arsenic (III), arsenite, from aqueous solution using calcined Quintinite-3T. The two adsorbents Quintinite-3T was prepared, calcined at different temperatures, and characterized by XRD, BET, and SEM. The surface area of the calcined Quintinite-3T was 193.4 m2/g. The particles size ranged from 12 to 56 nm for the uncalcined Quintinite-3T and from 24 to 42 nm for the calcined Quintinite-3T. Kinetic analysis, adsorption isotherm, and factors affecting the adsorption were investigated. Calcined Quintinite- 3T retained As(v) and did not release it back to water even after an entire month.

Jan 1, 2016

By Lóren Kelly de Paula Inácio, Witor Wolf, Renata de Oliveira Melo, Dagoberto Brandão Santos, Graziele Gianini Braga Maria, Nayara Aparecida Lopes Viana

Os aços inoxidáveis duplex combinam as propriedades mecânicas da ferrita com a resistência à corrosão da austenita. Quando submetido a tratamentos térmicos, pode haver precipitação de fases secundárias que prejudicam a resistência mecânica e à corrosão. O objetivo desse trabalho é avaliar a ocorrência de fases secundárias em um aço inoxidável duplex 2205 de grão ultrafino laminado a frio e submetido a temperaturas de recozimento de 600°C a 950°C por diferentes tempos (300-86400 s). Para identificação e quantificação das fases, foram utilizados microscopia eletrônica de varredura, difração de elétrons retroespalhados e difração de raios-x. As propriedades mecânicas foram avaliadas através de ensaios de tração e teste de microdureza Vickers. A presença de fase  e  foi observada junto ao carboneto de cromo, M23C6. A fase  foi confirmada apenas depois do tratamento à 800°C. De modo geral, o aumento do tempo de recozimento leva à uma maior precipitação das fases secundárias. À medida que a precipitação ocorreu, houve aumento da fração volumétrica de austenita e redução da fração de ferrita. Embora a resistência mecânica tenha aumentado, no geral, as propriedades mecânicas, como ductilidade, são prejudicadas pela precipitação.

Oct 5, 2019

By Luiz Gustavo Franco Amaral

The recent tragedies that occurred in Brazilian territory had a greater impact than that presented in the major newspapers and led an entire industry to question the technology and techniques that were previously practiced in the mining industry. With this, there is the prospect of new projects and innovations in the most varied branches of engineering. This publication presents computational technologies to support the decision making of engineering projects aimed at the mining sector and explores the benefits obtained from the use of current technologies in the mining sector. Recent works are referenced in order to propagate not only the methodology employed in these researches, but also to provide the reader with an overview of the industry and companies that invest in technology to support their decision making in the most diverse projects gains on products and processes obtained through this practice.

Oct 3, 2019

By Pedro Jorge Walburga Keglevich de Buzin

The steel production in mini mills generates several process residues, among them the electric arc furnace dust (EAFD). This residue has as main elements Fe, O, and Zn, being classified as hazardous by the presence of Pb and Cd. In recent years, a rise in the chlorine content of this residue was observed, motivated by the increased use of scrap with impurities bearing this element. In this work, a qualitative assessment of the presence of chlorine in the electric steelmaking process is made. Complementing it, theoretical considerations based on the computational thermodynamics tool FactSage show the effects of the chlorine on the mineral species in EAFD and on gaseous species in the gas phase (HCl and Cl2). For this study, PVC polymer was used as the chlorine carrier substance which contaminates the EAF charge; presence of other minor elements in the system such as K, Na and Pb were also considered.

Aug 7, 2018