Search Documents

By E. A. van Dijk

Dusts from steel-making processes contain substantial amounts of zinc. Such dusts are also a hazardous waste and dumping them becomes unacceptable from environmental point of view. Therefore processes that can recover zinc and possibly other metals from steel-making dusts are being investigated. The aim of this paper is a contribution to the more fundamental kinetic aspects of zinc reduction from silica free calcium ferrite slags. The effects of alumina, lime and magnesium oxide contents of the slag, the COICO, ratio and the effect of initial Fe2O3/CaO ratio were studied experimentally at 1400°C The results indicated that the reduction of zinc from molten slag was possibly a first order reaction. As expected higher COICO, ratios increased both the extent and the rate of reduction. It was also observed that a higher iron content of slag improved the reduction of zinc from calcium ferrite slags. This fact seems to support the proposed mechanism that zinc is partly reduced by ferrous iron to zinc vapour and that ferric iron is reduced by carbon monoxide. The reduction rate of zinc in these slags was decreased by increasing alumina content of the slag. Alumina decreased the calculated optical basicity of the slag showing the fact that reduction of zinc oxide was more favorable in more basic slags. Probably the formation of complex ions by alumina and zinc oxide such as ZnAl2O32+ lowers the activity of Zn2+ ions in the slag and hence render them more difficult to reduce.

Jan 1, 1999

By C. J. Malek

The CONTOP® smelting cyclone technology is a large-scale and time-proven method which in combination with other technologies (grinding, drying, pyrolysis, etc.) provides for a cost- efficient and ecological disposal of a wide range of waste materials from industry and households. In this report the basic principle of smelting cyclone technology will be explained first. Subsequently, the paper will discuss substantial concepts for the recovery of various remainders.

Jan 1, 1996

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

By B. Erik Ydstie, Tor Lindstad, Vianey Garcia-Osorio

"As a result of the high temperatures present in a Carbothermic Aluminum Process the content of aluminum and aluminum sub-oxide in the gases leaving this process is high. These gases as well as energy must be recovered. In a Vapor Recovery Unit were the aluminum compounds react in a series of Heterogeneous Non-catalytic Reactions forming solid, liquid and gas products. The different product phases depend on the temperature present in the system. In this work we present dynamic model of the Vapor Recovery Unit of a conceptual Carbothermic Aluminum Process. Because of the complexity of the system several models are developed and coupled to capture the essential physics of the multiphase reaction problem. A Shrinking Core Model describes the reaction mechanisms. Then material and energy balances are coupled with the thermodynamics properties from the FACT database of thermodynamic properties, resulting in a system of nonlinear Partial Differential Equations. In the paper we describe the model development and governing equations for the reaction mechanisms and fluid flow. Finally we review the numerical schemes created for the solution of the model system. The model can be used for control and design purposes.IntroductionThe Carbothennic Processes for producing Aluminum can be divided into two groups (Motzfeldt et al. (1989)) In the first approach pure alumina is produced and reduced to pure aluminum. In the second approach an alloy (e.g. aluminum and silicon) is made and then aluminum is produced from the alloy. The history of both processes has been described by Ginsberg et al. (1965). At least three aluminum producers began largescale testing of this process in the 60's Alcan, Pechey-Ugine and Reynolds. Alcoa did some smaller scale experiments.Alcoa was one of the first companies to produce aluminum by Carbothennic Reduction (Foster et al. (1956)) and US Patent 2,829,961 April 8, 1958. In this process a carbon containing molten aluminum phase was a floated on top of an oxy-carbide melt. During the cooling the dissolved carbon deposited as aluminum carbide. The carbide was then separated from the molten aluminum by a fluxing agent. This process was successful but economic unfeasible."

Jan 1, 2001

By A. Toulet

Mining in Mexico has an immensely long tradition. In his first letter reporting to his sovereigns from Mexico in July 1519, Hernan Cortes wrote, "To our mind it is probable that this land contains as many riches as that from which Solomon is said to have obtained the gold for the temple ... " 1 But not only precious metals drew his attention; in 1524, short of tin needed for casting guns, he found it in Taxco. As an added bonus, those who went to find it "came upon a vein of iron which according to experts is of exceeding richness." 2 Since then, the mines of Mexico have yielded up enormous amounts of mineral and continue to do so. Mexico is one of the ten principal producers of minerals world-wide both in production volume and diversity. 3 Tens of thousands of tons of iron, sulphur, and coal come from its earth annually; it is the world's second largest producer of barite; third of antimony, fluorite, and graphite. 4 Copper, zinc, silver, molybdenum, arsenic and cadmium and others are wrested from its mines. The wealth is there; but maximizing its potential requires investment, technology, and markets that the government cannot itself provide. Thus mining, since the Mexican Revolution severely restricted by both law and policy, today looks to private investment to develop its potential. Beginning in 1989, Mexico's government cautiously moved to liberalize private sector involvement in mining; 5 using the experience gained from these initial regulatory changes, the current new Mining Law was adopted in 1992 6 and new Regulations were promulgated in 1993. 7

Jan 1, 1994

By S. C. Grund

In secondary copper smelting as it is performed at Hüttenwerke Kayser plant in Lünen, tin-and lead-containing flue dusts are produced as intermediate products. These flue dusts are further processed in a hearth furnace. Followed by certain refining operations a saleable tin-lead-alloy is produced. Even though the hearth furnace technology has been in use for this purpose for a long time still its performance undergoes changes in search for optimum processing conditions regarding to the increasing complexity of the raw materials and tightening economical and ecological boundaries. The use of modern statistical tools for the calculation of accurate mass balances is demonstrated for the tin-lead hearth furnace. These reliable mass balances are the basis for any further modelling of the process with the aim of optimization. Incorporating metallurgical knowledge and experience as well as different mathematical modelling techniques, further studies are planned in which the recoveries of valuable and minor elements and their dependency from various process parameters are examined. The aim of this modelling is to optimize the recoveries of the valuable elements, to minimize the energy consumption and the processing costs and thus to keep the process competitive in a harsher economical and ecological surrounding. The modelling principles are transferable to other metallurgical operations and are especially suited for ill-defined pyrometallurgical processes.

Jan 1, 1999

By Bill A. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six-head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin.The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill.The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator's station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt, and mesh sump.The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in tum lowers the miners' roof exposure per cut. This design reduces the operator's exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore, the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely."

Jan 1, 2016

By J. A. Haggman

In a country richly endowed in mineral wealth, Climax Arimco Mining Corporation's (CAMC) Dinkidi porphyry Au?Cu deposit in Nueva Vizcaya province, Philippines, represents the most significant mineral discovery in the country in recent times. The deposit is located within a belt of young intrusive and volcanic rocks in the Sierra Madre mountain chain of north Luzon a region previously unassociated with porphyry-style mineralization. Since 1989, drilling of the Dinkidi deposit has outlined a resource of 124 million tonnes of 1.0 g/t gold and 0.41 % copper. Regional exploration throughout CAMC's 37,000 hectare FTAA has identified a further sixteen potential porphyry-related deposits. A new mining law was passed in March 1995 but prior to that CAMC had the first Financial and Technical Assistance Agreement (FTAA) granted by the Philippine government allowing 100% foreign ownership of mining projects.

Jan 1, 1997

By G. Rajesh

Mathematical modeling of bioremediation has gained importance as it is used as an optimization tool for the remediation process involved in contaminated sites. The bioremediation of Cr(VI) has been studied taking into consideration the initial Cr(VI) concentration Cr(VI)ini, bacterial growth substrate concentration (S), maximum growth rate (µmax), yield coefficient (Y), half saturation constant (Ks), and inhibition constant (KI). As the enzymatic reaction is also affected by initial substrate concentration (Sini) and Ks, different ratios of (Ks/Sini) are analyzed. As the inhibition constant (KI) is not constant for all the enzyme reactions and it varies with Cr(VI)ini, the correlation between (KI) and Cr(VI)ini is developed. A set of differential equations pertaining to bioremediation of Cr(VI) has been solved using FORTRAN 90 program adopting the model developed. The results are verified with the experimental data from the literature and a good correlation has been obtained between the experimental data and the model predictions. Keywords: bioremediation, hexavalent chromium, mathematical model, inhibition kinetics

Sep 1, 2012

By G. H. Charlewood, J. W. McBean

"One hundred years after being developed, the diamond drill is still an essential tool in mineral exploration. The basic principle is unchanged, but the technique has been revolutionized, particularly in the past fifteen years. The cost of core drilling has not kept pace with the rising cost of living. The price of machinery, supplies and labour in drilling has doubled and trebled since 1946. Some of the techniques which have made it possible to hold the price line are described."

Jan 1, 1967

By R. H. Lien

The Bureau of Mines investigated nitrous oxide (N20) stability when used as a solvent for organic removal from metal powder surfaces. Both supercritical and subcritical conditions were studied. This investigation was prompted by the occurrence of a violent reaction when supercritical N20 was being used to deoil a metal powder grinding waste sample that contained 20 to 25 wt pct cutting oil. Tests were conducted to determine the cause of the reaction and to define stability limits. Test data showed that the waste's oil fraction reacted violently with N20 acting as an oxidizer; the metal powder acted as a promoter to reduce the ignition temperature. Although the data were scattered, this temperature appeared to reach a minimum at a certain pressure (dependent on vessel and sample size). The minimum ignition temperature for a 0.64-g sample in a 72-cm3 vessel was 360° C at 200 psig. As the sample size increased, the ignition temperature decreased. For example, when the sample size was increased to 10 g, a reaction occurred at 240° C and 600 psig. Because of the variability of ignition temperature with pressure and sample size, safe operating conditions were not established. Overall, this research showed that extreme caution should be exercised when using N20 in an organic or organic-metal system.

Jan 1, 2011

By Hector Henao

To provide thermodynamic data for converting the nickel matte to liquid nickel, an experimental study was conducted in the phase equilibrium between the Ni-S alloy and the CaO-Ah03 based slag melted in a MgO crucible at 1873 K under controlled Pso2 of 10.1 kPa and pO;, in a range between 2.5x,IO,2 and 10.1 Pa by using CO-C02-S0Z gas mixtures. The content of nickel in the slag at POz of 10.1 Pa, above which solid NiO is expected to precipitate in the equilibrium state, was found to be 4.1 mass% and the contents of sulfur and oxygen in the nickel melt were 0.4 and 0.2 mass%, respectively. It was clarified that increase in the temperature reduces the solubility of nickel in the slag and the contents of sulfur and oxygen in the alloy. The distribution of minor elements such as gold, silver, copper, cobalt, iron, arsenic and antimony between the Ni-S alloy and the CaO-AI20) based slag was also studied. The distribution ratios of iron and cobalt, defined by (%X in slag)/[%X in alloy] where X is the minor element, are larger values than that of nickel, while those of copper, silver and antimony are similar to that of nickel. The distribution ratios of arsenic and gold are lower than that of nickel in the higher range of oxygen partial' pressure.

Jan 1, 2003

By Egil Aukrust

"An American Iron and Steel Institute Task Force evaluated developing direct steelmaking technology worldwide to seek a replacement for the coke-oven, blast-furnace, basic-oxygen process technology now in use. To remain internationally competitive it is essential to move away from the traditional series of batch processes towards continuous processing and the associated energy savings which are possible with high technology process control systems. The group identified in-bath smelting of iron ore pellets or fines with coal as the process most sui table for domestic raw materials (including abundant scrap) and called for research to study operation with varying degrees of preheat and prereduction of the ore by the gases generated from the coal and various degrees of combustion of these gases above the melt.A coordinated, 3-year, $27 million, direct steelmaking research program is proposed. Concurrent projects include design, construction, and experimental operation of an in-bath smelting pilot plant; modeling, simulations, and laboratory-scale experiments at universities on slag-phase and metallicphase reactions and interactions; and large-scale heat transfer and reaction rate trials. Also included are modeling studies and pilot plant trials of on-stream decarbonization and desulfurization; application of circulating fluid bed technology to fine ore reduction and hot gas cleanup; and specific heat transfer and fluid flow research projects.IntroductionThe American Iron and Steel Institute (AISI), based on the Task Force studying direct steelmaking, believes strongly that a coordinated program of research on the reduction of domestic raw materials to liquid steel should be undertaken as part of the Steel Initiative program. To specify the steelmaking process for development best suited to the American steel industry and domestic raw materials, it was important to determine the state-of-the-art of direct steelmaking worldwide, both as practiced and under development, and then, by expert analysis of the processes and their potentials, to choose the process most likely to provide a domestic competitive edge."

Jan 1, 1988

By T J. Sullivan, H Pinkster, G Swarbrick

From 2002 to 2006, longwall mining was undertaken directly beneath the Cataract Tunnel, which is a 100-year-old, heritage-listed tunnel in Hawkesbury Sandstone responsible for delivering 20 per cent of Sydney’s annual water supply. At one location, undermining resulted in movement of at least 350 mm along a known fault that transects the tunnel. During this movement, the continued operation of the tunnel was ensured through a careful system of planning, monitoring and management.Of key importance to the success of the operation was the use of advanced numerical modelling to guide operations at all levels, including feasibility assessment, pre-mine mitigation works, monitoring design, operation performance and post-mining condition. This allowed many aspects of the potential impacts to be explored, including joint movements, rock mass deformations and changes in permeability. A key challenge was to successfully model near-field influences on adverse geological structure due to very far-field effects. This paper explains the model’s conceptual development, calibration, performance and limitations.Modelling provided the confidence to manage the impacts of large mining-induced movement on key infrastructure and ultimately predicted fault movement accurately. The fault movement remains one of the highest ever recorded due to mine subsidence.CITATION:Swarbrick, G, Sullivan, T J and Pinkster, H, 2014. Longwall mining beneath critical infrastructure – prediction versus performance of the Cataract Tunnel, New South Wales, Australia, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 157–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By W. C. Baver

Even before the energy crisis developed in the early '70's, considerable research world-wide was being directed towards the development of schemes to both reduce the energy requirements and to reduce air pollution emissions associated with the manufacture of glass. In many cases the sought-for solutions would benefit both objectives. If, for example, the glass batch could be consolidated into such compact forms as briquettes or pellets, they could be preheated in a moving-bed heat exchanger with the high-temperature exhaust gases from the glass furnace. Lower furnace temperatures would thus be possible with a corresponding reduction in heat losses and total fuel consumption. Moreover, the lower temperatures would also reduce the amount of nitrogen oxides generated in the furnace and emitted to the atmosphere. Many tests on consolidated glass batch have been run in many countries. In some cases, extended tests on production furnaces have also been included in the programs. For various reasons, however, none of these has proved to be economically attractive. The current, but temporary lull in the rapidly rising cost of energy which has been with us in recent years, has reduced the push for research for energy saving means for melting glass. A few of the current programs will be discussed. Since raw material requirements, primarily physical in nature, are affected by some of these schemes, these will also be considered.

Jan 1, 1986

By A. Karzhau, B. Aldamzharov, Y. Tussupbekov

"This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of the mine 24 hours a day. The mine auxiliary ventilation has been designed with the maximum length of ducting systems with extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal. The mine needs additional investments for re-designing ventilation network and therefore needs to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation network optimisation processes at the operational metal mine in Kazakhstan. Mine ventilation surveys were undertaken for validation of the computerised ventilation model. The mine ventilation network modelling has been undertaken to be compliant with Kazakhstan mining regulations. Results of the mine ventilation optimisation processes were analysed in terms of financial risks for investments into reconstruction of the ventilation shafts, extension of the ventilation network, variable speed fans and automated regulators. Savings were resulted from improving ventilation system efficiency by reduce airflow in areas without mining activity and redistributing existing ventilation capacity. Based on savings derived from the optimised ventilation network an additional NPV has been received. Stochastic modelling use Monte Carlo simulation producing representation of possible outcomes for the additional NPV considering electricity pricing as a major variability. As result probability distribution for the optimised ventilation network demonstrates the additional NPV in a range of 1.6 - 2.2 million US$ in the corresponding defined value of 90%. Moreover, there is only 5% chance that the additional NPV to be less than 1.5 million US$. Conducted risk analysis for ventilation network optimisation processes gives considerations on volume of investments into the mine ventilation system.INTRODUCTIONCosts for mine ventilation are typically increasing when mines expand to deep levels. Some underground mines in Kazakhstan still use continuously operating fans at its maximum capacity. This is not helping to save energy and costs that are in many cases very significant. This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of a mine 24 hours a day. The mine auxiliary ventilation has been designed with maximum length of ducting systems and extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal from the mine workings (Sabanov, 2019). The mine needs additional investments for re-designing ventilation networks and therefore need to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation networks optimisation processes at the operational mine in Kazakhstan. Mine ventilation surveys for validation of the computerised ventilation model have been undertaken"

Jan 1, 2019

By Raphael Trousselle, William Reisz

The blasting industry is now well into its second decade of commercial use of electronic detonators. As an increasing number of blasters are introduced to the technology, the benefits are becoming more widely monitored and accepted in many surface blasting operations. However, their use in underground applications is not yet as widely established. This is primarily due to the distinct cost dynamics and processes associated with underground lasting.

Jan 1, 2012

By Henry R. Colen

When we were asked to prepare a paper on gold to be part of the Economics of Precious Metals session, our immediate thought was that we should address the question of supply. Are the existing mines of the world capable of filling the demand for gold? We recognized that gold does not conform to the normal pressures of supply and demand. Major new sources of production and increased sales might have a very short term effect and depress the price but this does not last very long. Those forces that affect gold prices are very different from the ones economists normally deal with. Factors such as mass psychology, political tensions and fear are certainly more important to the gold price than supply and demand in today's world.

Jan 1, 1981

By Jan Butra

Longstanding mining of copper deposits in the Legnica-Glogow Mining Basin, Poland has accumulated broad experience concerning the impact of geological and mining conditions on seismic and rockburst hazard. Methods of rockburst prevention for deep copper mines have been developed based on gathered data. Methods of rockburst hazard evaluation and rockburst control constitute a set of rockburst prevention measures. Due to their nature and location within the production process, prevention methods can be passive or active. Active methods of rockburst prevention consist of the liquidation of stresses in the areas where they are concentrated through controlled generation of rock-mass tremors and rockburst by blasting works (group extraction blasting, release blasting in the rock mass and pillars able to accumulate the stress, as well as in the roof and floor). Group blasting works as a basic method are very effective in copper mine conditions. Provocation of dynamic events makes it possible to control the timing of their occurrence. In Polish copper mines, all blasting works are made during the absence of miners in the mining fields. Daily distribution of both the number of recorded strong seismic events and volume of energy released, confirm the advisability of using this kind of rockburst hazard prevention. The rockburst hazard prevention methods developed over 40 years of copper deposit extraction are economically reasonable and offer sufficient effectiveness under high rockburst hazard conditions.

Aug 1, 2013

By George S. W. Cumpston

El presente texto describe los factores que intervienen en la economía de la molienda con bolas, considerando la carga y calidades de las mismas. Para determinar cuáles son los factores en el estudio económico, es necesario conocer las cuatro calidades básicas de las bolas de las moliendas: las bolas de aleación de acero, forjadas y con tratamiento térmico, las bolas de acero al carbono forjadas y con tratamiento térmico, las bolas de aleación de acero fundido y las bolas de fierro fundido. Los productos fundidos generalmente no son tratados térmicamente y las bolas de fierro fundido son un producto de bajo precio y más ordinario. En este sentido, una bola tratada térmicamente sea en aleación de acero o de acero al carbono, tendrá una estructura granular más fina que las de los productos fundidos. Para fijar la economía de un tipo de bola, se utilizan dos formas de investigación: la prueba de bolas marcadas y la de resultados de producción, estableciendo esta última como la más exacta, aunque requiera molinos duplicados para medir su producción. Luego, se procede a experimentar con diferentes tipos de bolas -a través del costo de transporte y manejo requeridos para moler una tonelada de mineral- y asi determinar cuál es la bola más económica para cada operación. Posteriormente se evalúa la facilidad de la molienda y se delimita la carga de bolas que se aproxime mejor a la carga balanceada.

Jul 20, 1960