Search Documents

By Henrique Lacerda Eleutério, Aldo Henrique de Almeida Barbosa, Vicente Tadeu Lopes Buono

The automotive industry’s interest in galvannealed (GA) boron steel for hot forming processes application has been steadily increasing due to its excellent surface quality, galvanic protection provided to the parts, good paint adhesion and better weldability in relation to other coatings for this application. In this study, samples of 22MnB5 galvannealed steel were heat treated and hot stamped on a water cooled die in laboratory scale. The influence of heat treatment on stability of coating and steel was assessed by using initial heating rates 11.0ºC/s and 15.0ºC/s. Microstructural evolution of galvannealed coating and structural integrity of steel during hot forming were investigated by scanning electron microscopy with energy dispersive spectroscopy analysis (SEM/EDS/Line scan), X-ray diffraction (XRD) and optical microscopy (OM). It was possible to quantify the Fe-Zn phase evolution during hot forming, to understand the effect of these heating rates on the product properties and to establish an optimized heat treatment for hot forming of these steel. The heat treatment with the heating rate of 15.0ºC/s presented greater operational flexibility and final products free from surface defects or cracks in the substrate.

Oct 1, 2019

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018

By Richard J. Mainiero

Traditional techniques for the experimental determination of toxic fumes produced by the detonation of high explosives are not applicable to blasting agents. To detonate properly, blasting agents require confinement, a significant booster, charge diameters of 3 inches (7.5 cm) or greater, and charge lengths greater than two-times the charge diameter. Without these conditions, blasting agents will not detonate at full order, leading to a misrepresentation of the gaseous products. A facility for detonating large, confined charges in a controlled volume has been constructed at the Pittsburgh Research Center’s Experimental Mine. The facility consists of a portion of mine entry (once used for full-scale mine explosion research and demonstrations) enclosed between two explosion proof bulkheads. Total volume of the chamber is 9,666 ft (274 m). The chamber is equipped with an air circulating system and is3 3vented using the mine's airflow. Up to 10-pound (4.5-kg) charges can be detonated in the chamber using a variety of confinements. For a typical test, the blasting agent is confined in a 4-inch (10-cm) schedule 80 steel pipe and initiated by a 3-inch (7.5-cm) diameter, 1-inch (2.5-cm) thick Pentolite booster. This combination of confinement and initiation yields a detonation velocity of about 4,000 m/sec for ANFO. This velocity is in line with that measured for blasting in the field. Twenty four 2-inch thick steel plates are suspended around the pipe bomb to stop shrapnel that would otherwise seriously damage the chamber. Following detonation of an explosive in the chamber, a circulating fan is run for about 10 minutes to uniformly mix the chamber atmosphere. Fumes samples are taken out of the chamber through 1/4-inch (0.6-cm) Teflon or polyethylene2tubes for analysis. The fumes are analyzed using bubblers or Vacutainers to collect samples for analysis by the analytical chemistry lab. The technique described here has been employed to determine the fumes produced by the detonation of a variety of ANFO formulations and commercial explosives. This technique may be developed as a standard test to measure fumes produced by blasting agents or may be used to provide data with which to develop a computer model that will reliably predict the expected fumes production based on chemical composition.

By L. B. Gittinger

Mr, Chairman, members- and guests of the AIMS, I greatly appreciate this opportunity to speak before you. I hope this is just the beginning of a long and mutually beneficial relationship. This winter I decided to join the other 36 Freeporters who belong to the AIME; and, I applied for membership in the Society of Mining Engineers. To queries as to my interests in the Society, I had this answer: our principal challenge -- more so today, than at any time in my nearly 25 years in the industry -- is discovery and development of new sources of raw materials. I want to join you in meeting this challenge.

Jan 1, 1966

By W. G. Fischer

Trona ore at the Westvaco mine of FMC Corporation has been obtained by room- and-pillar methods since the mine began operation. The flat-lying, 10-foot bed of trona, Na2CO3 NaHCO3 2H2O, is covered by 1500 feet of weak shale and sandstone. Extraction of pillars on the retreat quite often throws large amounts of weight onto development workings. Weak shales in the roof and floor fail rapidly and the mine ribs slough to such an extent that mining often becomes very difficult. When this occurs efficiency goes down, costs go up, and the risk to men and machinery increases greatly. Difficult mining conditions in the early 60's forced a re-evaluation of all presently known mining techniques in bedded deposits. Many room-and-pillar mining plans' were compared with the system in use at that time, but none of them offered a better solution to the roof control problem. Longwall techniques were seriously considered, but machinery was not available that would cut the hard trona seam and still maintain the productivity obtained from room-and-pillar sections. Roof cones troy in the longwall methods appeared to be more satisfactory than that found in room-and--pillar techniques. It was therefore felt that a new technique using the longwall principle and based on rock mechanics should be tried rather than previously known pillaring methods.

Jan 1, 1966

By Donald Crowell

Due to falling metal prices and depletion of ore reserves, lead-zinc mining in the Leadville, Colorado, area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Company and ASARCO with ASARCO being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Company of Salt Lake City in conjunction with the Central Engineering Department of ASARCO. The plant was constructed by Stearns-Roger Corporation. Construction began in the spring of 1970 and the plant went onstream in April, 1971. Flow sheets and equipment lists are attached. This paper will describe the flow sheet very briefly and discuss in more detail those aspects of the design which may be of interest, particularly the provisions for expanding the capacity of the plant.

Jan 1, 1972

THE opening session was held on Tuesday evening, February 17th, in the house of the American Society of Civil Engineers. The President of the Institute, Mr. E. B. Coxe, after a few introductory remarks, congratulating the members on the general prosperity in all the branches of the professions and manufactures represented by the Institute, called on Mr. E. F. Loiseau, of Philadelphia, for the first paper, On the Successful Manufacture of Compressed Fuel at Port Richmond, Philadelphia. Professor Prime called attention to the fact that the work of the United States Testing Board had been left unfinished at a point when valuable results had just been reached, and offered the following resolutions: WHEREAS, The American Institute of Mining Engineers has seen with regret that the work of the United States Testing Board has been suspended through the lack of an appropriation by Congress, which appropriation dues not seem likely to be renewed, and WHEREAS, It seems most important to the vital interests of our iron and steel manufactures that the experiments commenced by the United States Testing Board should be carried to successful completion ; Resolved, That a committee of three be appointed, to act with a like, committee to he appointed by the American Society of Civil Engineers, to carry out to completion the work commenced by the United States Testing Board. Resolved, That the American Society of Civil Engineers be requested to cooperate with this society by the appointment of a like committee. Resolved, That the committee have authority to request, in the name of the American Institute of Mining Engineers, contributions to a fund to be devoted to the completion of the experiments aforesaid. Resolved, That the Council of this Institute be authorized, whenever requested by the committee so appointed, to petition Congress for the free use of the testing machine at the United States Arsenal at Watertown. Resolved, That a committee be appointed by the President, to select the afore-said committee of experts. Resolved, That the President of the Institute have authority to fill any vacancies which may occur in the committee. The resolutions were unanimously adopted, and President Coxe appointed the following committee in accordance with the resolutions : Messrs. A. L. Holley, James Park, Jr., and J. F. Holloway. The President also appointed Messrs. Heinrich, Mickley, and Spils-

Jan 1, 1880

By R. W. Waytulonis

New exhaust control techniques and devices may be necessary to meet future diesel particulate matter emission standards in underground coal mines. This paper reviews conventional work practices and devices used to control diesel exhaust emissions, and new techniques being tested by the Bureau of Mines. Discussions will center on important work practices and on the function and efficiency of exhaust after-treatment devices. An industry/government cooperative research project to develop and test an exhaust after-treatment system for part 36 equipment is also discussed.

Jan 1, 1990

By Y Shougu

Many mine accidents will affect the mine ventilation system when they occur. At present, there is a lack of monitoring means to capture the occurrence of accidents in time by monitoring the ventilation system, so as to take emergency measures to reduce the loss of personnel and property. Pressure wave is an elastic wave existing in air. Most accidents in mine will cause obvious changes of pressure wave. It is an innovative idea to monitor the occurrence of accidents in mine by measuring pressure wave. The development and functions of the pressure monitoring device and related software are introduced in detail. The pressure wave monitoring test is carried out in San Xavier underground mining laboratory, and the D-wave and S-wave waveform data are collected. The waveform characteristics are analysed, and the main frequency distribution of the pressure wave is found to be within 1 Hz by using FFT. At the same time, the influence of the propagation distance of the pressure wave on the waveform is analysed. The propagation velocity of D-wave and S-wave are roughly calculated, and they are 279.6 m/s and 397.3 m/s respectively. S-wave is slightly faster than D-wave. Although there are errors and uncertainties in the test, the test verified the feasibility of the existence and collection of pressure waves in the ventilation roadway, and provides a method for the future study of the propagation of pressure waves in the mine ventilation system.

Oct 12, 2022

By A Späth

Active explosion barriers are used to contain and suppress a methane gas and/or coal dust explosion propagation, including localised mine fires. Early research indicated that these active explosion barriers could be used on a mechanised cutting machine, making it the only technology that could suppress an explosion during its propagation phase at the cutting face. Thereby not only adding protection during mining operations but also reducing the development of toxic gases, fatal temperature increase and fatal overpressure build-up. During their evolution over the last two decades, further advantages of Active explosion barriers were proven in mine operations in countries such as South Africa and China. Characteristics such as effectivity, efficiency, mobility and space restrictions allow these systems to be used in various locations within a mine operation, including highwall operations. This improved technology contribution to safer coal mining was recognised by mine operators, workers and regulators. The Queensland’s Recognised Standard 21 (Resources Safety and Health Queensland (RSHQ), 2021) stipulated active explosion barriers as a technology to ensure the safety within their underground coalmines. The mobility and flexible implementation of the active explosion barriers allow a feasible and practical solution for all critical locations for explosion and fire management in an underground coalmine. The conformance to the Recognised Standard can be achieved all underground coal mining operations such as Bord and Pillar, and Longwall mining. This paper describes the conformance, implementation and use of Active explosion barriers for Longwall mining and development as well as Bord and Pillar mining in Queensland’s underground coalmines.

Oct 12, 2022

By J Wen, P Hou, W Yu, M Hu, Z Jiang, C Bai

Vanadium titano-magnetite (VTM) is one of the important iron ore resources in the world. High viscosity and low fluidity are the basic characteristics of hot metal containing vanadium and titanium during the ironmaking process. Clarifying the influencing mechanism of the melt viscosity would be a significant issue for the high efficiency smelting of VTM. In this paper, a self-developed melt viscometer based on the principle of torsional vibration theory was employed to measure the viscosity of hot metal accurately. Simultaneously, the thermodynamic calculations and some modern detection methods were also used to investigate the precipitation behaviour of high-melting-point phases in hot metal containing vanadium and titanium. The measuring results show that the viscosity of molten iron gradually increases with the increase of titanium content when the mass fraction of titanium is between 0.09 wt per cent – 0.50 wt per cent. Meanwhile, the viscosity of the hot metal was affected significantly by the vanadium content. When the vanadium mass fraction was higher than 0.30 wt per cent, the viscosity of hot metal increased sharply, which will have a serious impact on the fluidity of the hot metal. Furthermore, it was revealed by thermodynamic calculations that an increase in titanium and vanadium content would result in the precipitation of high melting point phases such as TiC, TiN, VC, and VN in the molten iron, ultimately resulting in a decrease in its fluidity. Meanwhile, it was confirmed by Scanning Electron Microscope (SEM) observation that the precipitates in the hot metal were compounds consisting of V, Ti, C, and N elements, which agrees well with the thermodynamic analysis results.

Aug 21, 2024

By R Blin, R Walde, R Belli, D Inaudi

A fiber optic distributed sensing system allows the monitoring of parameters useful to determine the short- and long-term behaviour of the structure in response to the external actions, including, eg seismic activities as well as long-term phenomena such as seepage, tunneling, sinkholes, and other geo-structural movements. Monitoring of large retaining structures with such a system provides direct strain/deformation and temperature measurements on the broad interior area with an arrangement of several sensing cable lines, enabling early detection, localisation and sizing of subsurface damages. Measurements are provided every meter along the entire sensing cable, this is particularly important in such cases where the location of defects and damages cannot be predicted. Fiber optic distributed sensing cables are generally available for retrofit installation inside the dam structure using trenches on the downstream face or laid during construction below the geomembrane liner within the bedding sand layer. Mapping the cable route enables exact correlation between a linear coordinate on the cable length and a position in the dam. Cable installation is envisaged to be carried out during further raising of the embankment; additional cable sections are plugged to the previously installed cables and measured with the existing measurement system, requiring only an update of the mapping. The measurement system is placed remotely from the sensing area since a section of sensing cable can be used to link to the sensing area at the storage facility several kilometers away. The system is available for on-line, 24/7 real-time operational data management. Such fiber optic distributed sensing systems allow storage facilities to be monitored with long, accurate, continuous and precise data for geotechnical diagnostic purposes. This contribution will introduce the principles, benefits, and limitations of this technology.

Jul 1, 2021

By P Jonsén, S Larsson, M Parian, B I. Pålsson

The question of effective energy utilisation in grinding mills is not new. There are several conflicting arguments about tumbling mills, whether the efficiency is around 1 per cent or maybe 10 per cent, or even much lower. The energy not used is assumed to be lost as heating of the pulp, the grinding mill body, the charge, generation of shock waves and vibrations, etc. Stirred media mills on the other hand are generally considered to have better energy utilisation, but their energy efficiency is still not that clear. To shed some light on this a pilot-scale, wet stirred media mill was investigated over a range of operating conditions. The wet stirred media mill is a Drais PMH 5 TEX pearl mill fitted with an electric motor at 11 kW. It has been investigated over a range of operating conditions to try to balance the dissemination of the input energy in forms of the net grinding energy, mechanical energy losses, and the heating transferred to the pulp, the mill, the charge, and the cooling water. It is found that approximately 20–40 per cent of the input energy accounts for the grinding process. Also, that the difference between gross and net input electrical energy is mainly disseminated as heating of the pulp and cooling water. Mechanical energy losses appear to be much smaller than the heating effects. The use of a dispersant seems to mainly influence the heating effect.

Aug 24, 2022

By B Small

CSA Mine, named after the nationalities of the mines first owners being Cornish, Scottish, Australian, is one of Australia’s deepest and highest-grade copper mines. A combination of the modified Avoca method and shrinking was a standard practice where production rings were fired against and bogged to waste fill. This method resulted in dilution and involved rehandling of waste material to refill the bogged stopes in the Western region and the QTS Central. The introduction of pre-charging blastholes using a wireless initiating system (WebGen™) has enabled CSA to design and fire stopes in reverse. This involves the use of a pre-charged Temporary Rib Pillar (TRP) against the waste fill material in a previously mined stope. The temporary pillar reduces dilution and improves conventional bogging as material is blasted towards the drawpoint rather than towards the waste fill material. Additional drill, prep and blast re-work is reduced or completely removed as rings can be charged prior to, in conjunction with, or after, charging of the slot. This is a safer practice as the charge crew spend no time working adjacent to a brow or open void. A TRP trial was conducted in the western orebody at CSA. The risk of exposure to a brow or open void while charging underground, and the bogger rehandling of waste material was successfully eliminated. Once reverse stoping was established in modified avoca stopes at CSA, two TRPs were implemented in challenging ground conditions in the QTS Central region. The TRPs were utilised in a retreating four-way intersection to extract a central diminishing pillar to close the level out. The ore recovered in this stope provided 5 per cent of CSA’s copper for the year. Without pre-charging with a wireless initiating system, two 5 m pillars totalling 6936 t of ore at 7 per cent either side of the stope would not have been recovered. CSA has implemented the practice of reverse stoping in modified avoca stopes using TRP for ten stopes since the successful trial. The development of additional blasting techniques enabled by precharging with wireless initiating systems is currently underway in the QTS North orebody at CSA Mine.

Mar 29, 2023

By A Mooney, G Balog, P Burns, R Brooks

This paper outlines the rationale for the location of the crusher, geotechnical analysis and basis of ground support design, design and scheduling of the chamber and supporting excavations as well as the operational outcomes and lessons learned. Contributions from mining operations, planning, geotechnical and infrastructure teams enabled the Crusher Station One excavation to be completed on schedule, with opportunities taken for underground mining and infrastructure to work safely in parallel to deliver crusher station infrastructure on schedule. Installation of crusher infrastructure was ongoing at the time of writing.

Mar 15, 2021

By A D. Wulfse, C M. D Barton

Underground fractured aquifers in the Ernest Henry deposit are to a large extent controlled by deposit scale brittle structures. The underground mine has been subdivided into nine water zones based on hydrogeological characteristics, including conductivity and connectivity, within the mining areas bound by these structures. The nine water zones and the hydrological characteristics of the associated structures are utilised for risk assessing mine development and for targeting diamond drilling dewatering activities. Wireline and conventional underground diamond drilling techniques have been used throughout the network of underground aquifers with the aim of dewatering areas within the mining footprint. These dewatering drilling campaigns have historically been highly successful at lowering aquifer water levels throughout the underground workings. As part of recent mine expansion activities, diamond drilling has intersected high pressure (>507 psi), high temperature (>50°C) and high flow water (>3 L/sec) in as yet unconstrained underground aquifers. Groundwater is typically conducted through rubble and clay rich faults, further hampering progression of drilling. Drilling through fractured aquifers at depth presents both mine planning as well as safety challenges. Recent drill holes have been delayed or abandoned when aquifers hosting this high pressure, high flow water have been intersected, risking mine planning deadlines. Recent technological innovation developed to control groundwater outflows from the diamond drill hole whilst drilling has been trialled at the Ernest Henry Mine. This case study focuses on the utilisation of alternative drill methodologies to allow the current drilling campaign to continue without delay, whilst also improving safety conditions encountered on the drill site.

Mar 22, 2022

By Alexander Filotti, Richard Kalson

"In the last decade, the construction industry has witnessed significant changes in the project delivery systems and contractual relationships between the general contractors (GC) and Deep Foundation Specialty Contractors. The Deep Foundation industry, especially including industry specialty subcontractors, have experienced a significant increase in requests that project risks be transferred through contract documents to subcontractors and suppliers with a decrease in margins for the industry. GCs regularly revise their form subcontracts to take into account recent experiences/contractual trends and newly issued judicial precedent, an exercise that is less frequently undertaken by subcontractors and suppliers. These contradictory trends are at the base of the ethical analysis of subcontracts that comprises the subject matter of this paper. Using contracts as a risk management tool in order to mitigate the general contractor’s risks in the context of dynamic changes in the legislative environment will also be addressed. Furthermore, another possibility for risk mitigation for the industry is to actively promote the introduction of the latest technical developments into the contract documents.CONTRACTS’ ETHICSFor thousands of years, ethics have been a constant presence in our lives and have been debated by different branches of philosophy. In modern times, ethics in business started to be an imperative for the success of a globalized economy.“Ethics are standards by which one should act based on values. Values are code beliefs such as duty, honor, and integrity that motivate attitudes and actions.” (Rumbaugh 2004). Some of these values and actions have been carved in legislation in general and in business legislation in particular. More and more, unethical business practices (e.g., corruption) are identified as the root cause of poverty, underdevelopment, and war around the world. In the context of contract ethics, three aspects are of interest:•,Ethics of contract construction•,Ethics of contracting processes•,Ethics of risk allocation in contracts"

Jan 1, 2016

By Magella Pelletier

"IntroductionDepuis une vingtaine d'année, les nombreux travaux de géochimie effectués par l'industrie privée et les milieux gouvemementaux ont permis:• de découvrir de nombreuses zones minéralisées a valeur économique;• d'identifier et de vérifier certains patrons de dispersion géochimique au-dessu s de secteurs minéralises déjà connus;• de favoriser le développernent des techniques analytiques;• de forcer le développement d'une mise en carte des résultats d'analyse, qui soit plus adéquat afin de permettre une meilleure interprétation géochimique.L'une de ces cartes géochimiques qui permet le mieux de mettre en valeur les données analytiques et qui fut instaurée au debut des années 80, est la carte d'interprétation géochimique par pondération.Cette carte numérique semi-quantitative, qui est construite à partir des données de base et de l'importance des éléments indicateurs pour une substance donnée, permet d'identifier et de définir des zones possédants de fortes probabilités pour la recherché de sources minéralisées."

Jan 1, 1987

By Victor O. Strobel

Fire-brick hot-blast stoves have been the subject of frequent discussions at the meetings of the Institute; and although it is my object to elucidate some of the points in connection with this subject, I will not go into the specific features of all types, but more especially call attention to a new type recently designed by Mr. Fred. W. Gordon. As the economical production of a ton of pig-iron is a more essential feature than a large output, much depends, where fuel cannot be obtained cheaply, upon suitable apparatus whereby high temperatures can be maintained. Where iron-pipe stoves have been employed, the fuel-consumption reached one and a half pounds of fuel, and, when a larger output was desired, often two pounds, to the pound of iron produced. The temperature attained rarely exceeded 900' F., and that at the expense of frequent renewals of the pipes, which was not inconsiderable. The fire-brick hot-blast stoves of the past five or six years have clearly demonstrated their superiority over the old system. Of the accompanying drawings, Fig. 3 illustrates a four-pass regen-

Jan 1, 1886

By Kaixi Jiang, Lan Li, Bang Wei, Haibei Wang, Yaping Feng

"China is currently the world's largest copper producer. In the last five years, 950 kt/y of smelting capacity was commissioned. Currently, about 1200 kt/y smelting capacity is under construction and about 2000 kt/y smelting capacity is under feasibility study. Ausmelt/ISA smelting and flash smelting technologies were commonly adopted in China. After the double-flash-smelter was first adopted in 2004, three new double-flash-smelters are scheduled. Recently, two new copper smelting technologies were developed in China. One is an improved bath side-blown smelting process, and another is the SK.S bottom blowing process. Both technologies have been in practice for over three years and have achieved good technical performance. Approximately 500 kt/y new smelting capacity in China and India will adopt these technologies. Both technologies have the advantages of low investment cost, low energy consumption and high flexibility for complex raw materials. This paper reviews ""green"" copper smelting projects in China and introduces the practices of the two new Chinese smelting technologies.IntroductionPresently, China is the largest copper producer in the world. As far as the smelting of copper is concerned, there are many smelting processes applied in industrial production, such as flash smelting, Noranda smelting, Ausmelt smelting, Isa smelting, the Mitsubishi process, Vanukov smelting, silver copper-smelting, SKS smelting, both side-blown smelting, traditional blast furnace smelting, electric furnace smelting, reverberatery smelting and so on . Except the last three traditional processes that are eliminated because of their failure to meet the requirements for environmental protection, all of the other above-mentioned methods are advanced smelting processes adopted nowadays."

Jan 1, 2012