Search Documents

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By M. Buxton

"Advanced data acquisition and process modelling technology provides online data and decision support about different aspects of the resource extraction process. Real-time approaches have recently been applied to utilize the value of this information for improved production control in mineral resource extraction in different operational set ups including coal, polymetallic ore and gold deposits. The key concept of these approaches promotes the change in paradigm from discontinuous intermittent process monitoring to a continuous process and quality management system in the resource extraction process. The framework includes a real-time feedback control loop that rapidly links online material characteristics data acquired during extraction at the mining face, during material handling and processing with a sequentially up-datable resource model. This will allow near real-time optimization of decisions related to long-term planning, short-term sequencing and production control. The contribution reviews recent developments in the three main constituents sensor based material characterisation, rapid updating of grade control models and simulation based optimization for improved production control. Technological readiness is assessed and critical gaps for further technology development are identified. The value added is illustrated by means of selected case studies. INTRODUCTION With the depletion of known and established mineral reserves, the decrease in head grades and the continuing demand of mineral raw materials by the modern society, future exploitation will move towards extraction of deposits under geologically more complex conditions. Complex deposits are characterized by a low continuity in grade, presence of deleterious elements such as arsenic and high irregularity in the geometry of the ore boundaries. The profitable exploitation of such deposits becomes significantly more challenging. To be able to better utilize such unconventional mineral resources of the future, smart autonomous mining systems are needed, which integrate local exploration of spatially varying material characteristics in–situ and have the ability to follow and extract the pay zones in the ore body while minimizing dilution (Buxton and Benndorf, 2013). The main barriers to overcome for the successful economic exploitation are: • effective grade control which will maximize resource potential along the whole value chain, • minimization of handling zero-value material introduced by dilution, thus • reducing unnecessary expenditure of energy and financial resources and • management and control of the geological uncertainty due to limited information available,"

Jan 1, 2017

By Ela Mielczarski, Jerzy A. Mielczarski

"The adsorption of xanthate takes place at a different potential on each major sulfide mineral, hence, as it was demonstrated in the past, each mineral component can be selectively separated from ore under well controlled potential conditions. In real flotation this concept never works out for two reasons: the potential of single mineral particle results from complex surface reactions controlled by solution chemistry, and there is a galvanic interaction between different mineral particles present in the flotation pulp.In this study the formation of amyl xanthate hydrophobic products on pyrite, galena and chalcopyrite has been spectroscopically investigated in the presence of combinations of these minerals. The type of the adsorbed species and their amount were determined directly on mineral surfaces by infrared external reflection technique. Galvanic contact between grains of two different minerals has tremendous consequence on the adsorption of collector on both minerals. The detected changes are dramatic, from no adsorption to a coverage formation of a few monolayers. The results obtained indicate clearly that the observations and conclusions about the collector adsorption, hence also the surface hydrophobization, made for a single mineral system does not describe the real situation in a multi-component mineral system such as flotation pulp."

Jan 1, 2003

By J Dwyer, G Turner, D Pridmore, M Urosevic

Due to their ability to produce high-resolution images of the subsurface to great depths, seismic surveys provide critical inputs to almost all oil and gas exploration projects. However, with some notable exceptions, seismic surveys have rarely been used in mineral exploration. In the past, this was due to both technical and financial reasons. Significant developments on both fronts mean that seismic surveys can now offer substantial benefits to mineral exploration and mining, and surveys conducted for exploration can provide important data sets for mine planning over the life of a mining project.We present case history data that show that seismic surveys can greatly assist with mapping the 3D distribution of lithologies and alteration and, in favourable circumstances, directly detect mineralisation in and around mineral systems. As a result of their high spatial sampling density, seismic surveys are also highly effective at mapping structures that can remain undetected or poorly characterised by drilling alone. These structures may host or provide important vectors to mineralisation. They can also be particularly important when planning shafts, raise bores, declines, stopes and open pit walls. A further benefit of seismic surveys is that they can remotely provide information on geotechnical rock parameters that are used for rippability, slope stability, blasting and ground support.CITATION:Turner, G, Urosevic, M, Pridmore, D and Dwyer, J, 2015. Exploration and mining unified through seismic imaging, in Proceedings Third International Future Mining Conference, pp 117–122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By N. Geoffroy, E. Benguerel, G. P. Demopoulos

In the late 1990s, a chemical process to remove mercury and selenium from weak sulphuric acid solutions was patented and implemented in the CEZinc refinery in Valleyfield, Quebec. The CEZinc process comprises two stages. In the first one, sodium sulphide is added to the weak acid solution in order to precipitate the soluble mercury. The solution is then treated with sodium dithionite in order to reduce the selenium to elemental form. Because of recent changes in the composition of the industrial solution, a project to study the background chemical reactions was started. In this paper, a review of the background chemistry is presented on the basis of several eh-pH diagrams on one hand, while on the other experimental results are reported dealing with the reaction of selenium (IV) species with either dithionite, sulphide or a combination of the two. According to this work, elemental selenium enjoys a wide pH-eh range stability with selenium sulphide being metastable. Selenium (IV) in single metal synthetic solutions was found to be reduced - to elemental state - at ambient temperature down to ppb range with dithionite as long as the stoichiometric ratio (dithionite/selenium) was in excess of two and the pH < 1.7. Under these conditions the reaction was very fast reaching completion within one minute. Sodium sulphide proved equally effective in reducing selenium (this time as selenium sulphide) to ppb range from single metal solutions. However, in mixed Se-Hg solutions deviations from this "ideal" behaviour was observed resulting in higher levels of residual soluble selenium left in solution.

Jan 1, 2008

By M. Panayotova

Most of the quantity of the water soluble xanthates, used in mineral flotation, is consumed in the process. However, the residue amounts are water contaminants downstream the mineral processing operations and can be toxic to aquatic biota at concentrations of 1 mg/L. In order to be able to discharge water from tailing ponds to natural water bodies the concentration of xanthates has to be decreased. The present paper studies the uptake of potassium ethyl xanthate by directly modified with copper and lead ions natural zeolitic rock, without passing through zeolite transformation into homoionic form. Modified zeolite exhibits high, comparable with powdered activated carbon of chemical purity grade, capacity to remove potassium ethyl xanthate from model wastewater, with pH in the range of 7?9 and pollutant concentration in the range of 10-150 mg/L. The pollutant immobilization is fast. Both Cu and Pb modified zeolite behave as selective with respect to xanthate in the model wastewater, and Cu-modified zeolite possesses higher selectivity. The equilibrium is best described by the Freundlich equation. Keywords: xanthate, wastewater, modified zeolite

Sep 1, 2012

By N. Bat, N. Sarantsatsral

Blasthole sampling practices were investigated at the Erdenet copper and molybdenum mine in Mongolia to address grade reconciliation issues. The goal of the study was to determine if the particle size distribution (PSD) of blasthole cuttings was accurately reflected in the samples. The study additionally examined if the measured grade was related to the particle size of samples. Using a sector sampler specifically designed to collect samples for the study, six large samples were collected from three blocks following a specialized protocol. Each sample was split into nine size fractions, ranging from larger than 12 mm to smaller than 63 µm. Copper and molybdenum grades were determined for each of the size fractions. For comparison, nine samples were collected from the same blocks following the standard mine sampling protocol. These samples were also split into the same nine size fractions. As with the other samples, grades were determined for each of the size fractions. The results showed that the PSD in the samples collected following the standard operating procedure varied significantly from sample to sample. This variation was much lower for the samples collected following the specialized protocol. Loss of fines was also indicated in the standard mine sampling process. These observations suggest that the standard sampling protocol did not consistently capture the PSD. The copper and molybdenum grades increased as particle size decreased, regardless of the sampling protocol used. This observation underscores the importance of the PSD of a sample being representative of the true PSD. Given the low number of samples in the study, it is not a strong conclusion that the standard sampling protocol captures the PSD inconsistently. However, it could be taken as a caution. On the other hand, the grade versus PSD relationship is more certain, given that it was observed regardless of the sampling method used.

Feb 1, 2017

By T. A. Lang

The objective was to develop a Program Plan of analytical studies and tests for determining (1) the optimum installation tension of a coal mine roof bolt, (2) the most valid bolt support theory or theories, and (3) the most valid roof failure theory or theories. On this basis a comprehensive literature search was made and significant material dealing with coal mine roof behavior, roof bolting and roof support was collected, reviewed, classified and analyzed. Emphasis was given to the influence of rock reinforcement on the control of deformation, stress field modification and mine roof stability. An assessment was made of the effect of various parameters including bolt tension, bolt pattern and time of installation, on the effectiveness of rock reinforcement systems, and equations developed for bolt tension as a function of these parameters, and rock properties. From these studies, a major program plan of tests and studies was developed for verifying and validating the most tenable theories of roof behavior and roof support and for determining optimum bolt installation tension.

Jan 1, 1979

By E. G. Baltuch

Natural Ventilation in mining and metallurgical processing applications is key to proper operation function. There are number of ventilator designs available to a project team or design engineers, the selection of which will affect both the type of building structure required, project costs and design performance which is difficult to rectify or re-engineer once implemented. Research and applied results, such as that performed by Air-Therm Inc., demonstrates that computational fluid dynamic simulation allows for 5 dimensional observation, analysis and optimization at significantly lowered cost than previously possible. These results have been fully implemented on a number of mining and metallurgical applications and the company continues to study, optimize and innovate as new tools become available to provide the best possible engineered solutions for particular applications.

Aug 1, 2013

By B. H. Wadia

El presente texto describe las propiedades físicas y químicas de la plata, el proceso de extracción y refinados, las dos etapas de conversión, copelación, refinación electrolítica, producción de la plata esterlina, métodos de cianuración, lixiviación clorurante y volumen de producción.

Jan 1, 1984

By H. Colijn

Belt conveyors have proven themselves for many years as a dependable and low cost method of handling bulk materials at high flow rates. The success of a belt conveyor system greatly depends on the initial loading of the material on the belt. If the material is loaded on the belt at the center, at approximately the same speed and with minimum impact, then most of all belt conveyor problems disappear. Proper belt loading is primarily determined by the engineering and design of the conveyor transfer point. This paper will establish and discuss some general design criteria required for proper loading and transfer of materials from one conveyor to another. Specific attention is given to loading points, chutes, skirt board length and general design of transfer structures.

Jan 1, 1971

By J. P. Walsted

The lack of an iron-smelting industry in the Pacific Northwest places the ferrous metals industries under an economic handicap. No iron-smelting enterprises, now dormant, had been operated successfully. Iron made at both of hoes installations proved to be satisfactory for normal pig-iron uses. Electric power and reductants acre available in the area. Power from the dames now completed and. those being constructed insures present and future needs for basic industries. Subbituminous coal, close to the main supply of iron ore, insures ample reluctant for all smelting requirements.

Jan 1, 1954

By S. A. R. Keneti

Predicting the geomechanical response of the shale gas material during hydraulic fracturing operation in the field needs better understanding of their geomechanical behaviour under laboratory testing. Anisotropy is considered as a critical factor during investigation and analysis of deviated boreholes, borehole stability, stress-strain and strength behaviour, generation and propagation of fracture and fluid flow. In this study, compressive elastic modulus (Ec) of the Montney shale has been investigated in two perpendicular directions: unconfined compressive strengths test was conducted on the Montney sample to measure its Ec in the vertical direction. This value then was compared to the Ec value in the horizontal plane (i.e. foliation plane) which was previously measured throughout a Brazilian test by Keneti and Wong (2011). From the results, the representative values of Ec in the vertical and in the horizontal directions were found as 25 GPa and 40 GPa, respectively. Computer tomography technique was also employed for the experimental data interpretation.

Jun 1, 2012

By Itsuki Uehara, Hiroyuki T. Takeshita, Tetsuo Sakai, Nobuhiro Kuriyama, Hideaki Tanaka

"AB5 type hydrogen storage alloys (A: rare earths, B: transition metals) are extensively applied to a negative electrode of a nickel metal hydride (Ni-MH) rechargeable battery for portable electric equipments, electric vehicles, hybrid vehicles etc. Performance of a hydrogen storage alloy electrode is affected by various factors, microstructure and surface composition of the alloy and structure of the electrode as well as composition of the alloy. Control of those factors enables us to commercialize the Ni-MH battery in various field.IntroductionA Nickel-metal hydride (Ni-MH) battery has been extensively developed because of (1) good compatibility with a nickel cadmium (Ni-Cd) battery, (2) high energy density (1.5-2 times higher per unit volume than a Ni-Cd battery) and high dischargeability, and (3) low environmental pollution. The charge/ discharge reactions can be written as [l, 2,3]:(+) Ni(OH)2+OH- = NiOOH+H2O+e· (E=+0.490V NHE),(-) l/6LaNi5+H2O+e-· = 1/6LaNi5H6+OH- (E=-0.828V NHE),where E° is a standard potential of an electrode vs. normal hydrogen electrode (NHE). Because of the above advantages of a Ni-MH battery, the battery have been widely used as a power source of portable computers, cellular phones, electric vehicles (Toyota ""LAV4L EV"", Honda ""EV Plus"" etc.) etc. Some hybride vehicles (Toyota ""Prius"" and Honda ""INSIGHT"") and fuel cell vhehicles (Toyota ""FCEV"") are power-assisted by a high-power Ni-MH battery. In 1999, the production of Ni-MH batteries reached 870 million cells in Japan. Most of commercialized NiMH batteries are incorporated with rare-earth-based AB5-type hydrogen storage alloy as a negative_ electrode. The production of rare-earth-based alloy is estimated to be approximately 8000 tons.The battery performances of the Ni-MH battery, for example, capacity, durability (cycle life), dischargeability (kinetics) and selfdischarge, ate closely related to the metal hydride· (MH) electrode, especially, the hydrogen storage alloy in the electrode. Substitution of alloy components, heat treatment, and surface treatment in order to change surface and bulk structure of hydrogen storage alloys have been examined by us and many reseachers in order to improve the performances of MH electrodes. This paper is a review of our and their efforts to improve performances of MH electrodes."

Jan 1, 2000

By V. Runkana, N. K. V. Nadimpalli, S. Sahu

"IsaMill™ has been in operation in the recent past for fine grinding of low grade ores to extract non-ferrous minerals. IsaMill™, typically, consists of a series of uniformly spaced identical disks mounted on a rotating shaft which is encased in an outer shell. The mill offers high energy efficiency for fine grinding and an inherent scalability. But, it encounters certain operational challenges such as non-uniform distribution of grinding media coupled with high wear rate of the disks and solid walls of the mill at specific locations—which adversely affect the mill performance. To circumvent these operational challenges, design modification of the disks through heuristics, by introducing a reduced diameter disk (RDD) at specific locations, is a common practice in industry. But there is no systematic scientific study in this regard. In the current work, we developed a discrete element method (DEM) based model and simulated for the IsaMill™ operation to study the effect of RDD on the efficiency of the mill and wear rate of the solid walls and disks. Since the first set of disks experience the high wear rate due to the high loading of the charge, the RDD was introduced at the first two disks. The simulations were performed at different diameters of the RDDs and at different media loadings. The performance of the mill was analyzed based on the power consumption, the wear rate on disks and the distribution of media particles inside the mill. Besides, the performance variables such as mean velocity of media particles and total impact energy provided useful insights into the milling operation. It was observed that the reduction in disk diameter yields lower wear rate of the disks at the cost of decrease in power draw at a constant high media loading. Whereas, when the media loading was decreased, the amount of wear and power drawn was comparable for both the most reduced and least reduced disk diameters. Therefore, there is an optimum choice of RDD for a given mill loading to maximize the mill performance while reducing the wear rate of the disks."

Jan 1, 2018

By S. Klemmer

Potential problems associated with groundwater inflows are a major concern to many Saskatchewan mining operations. Rock mass behaviour and stability have been linked to groundwater inflow potential. An estimate of the hydraulic conductivity of the rock mass is an important factor for assessing groundwater inflow potential. This paper presents a procedure that was developed to conduct air permeability tests, for estimating the hydraulic conductivity of the rock mass. Tests were conducted near underground excavations with the goal of assessing links between measured air permeability, rock mass classification and the rock mass response to adjacent excavations. Measured changes in air permeability corresponding to the distance from excavation boundaries may indicate changes to joint properties such as joint aperture, continuity and frequency. This study outlines the instrumentation, the experimental and analytical procedures, and the preliminary results from testing.

Nov 1, 2011

By Mary F. Koehler

Interoxidic compounds, such as vanadates, have not been studied extensively in the field of thermodynamics. This is a report of three vanadates of sodium--metavanadate, pyrovanadate, and orthovanadate. Vanadates of other metals will be considered in future reports. The heats of formation at 298.15° K. of the three sodium vanadates (both from the oxides and from the elements) were derived from the results of sodium hydroxide solution calorimetry. Free energies of formation were obtained by combining heat and entropy values. The results support the conclusion that the three sodium vanadates were stable with respect to all possible decompositions in which vanadium retains its pentavalency.

Jan 1, 1960

By Jason Baird, Joshua Hoffman, Phillip Mulligan

The purpose of this report is to address the method of reducing the overall explosive weight of Explosively Formed Projectiles (EFPs) while still achieving satisfactory performance. This reduction is crucial in order to comply with outdoor explosives testing standards for Missouri University of Science and Technology’s (Missouri S&T’s) Experimental Mine. Initial EFP design testing exceeded given limitations, making reliable data difficult to ascertain. EFPs must be tested outdoors to allow for specific information recordings which aid in defending against them.

Jan 1, 2010

Aitik, a Boliden owned and operated open pit mine located in northern Sweden, will expand production from 18 Mt per year today to 36 Mt per year copper ore during 2010. The challenge for the mine operation is to double production with a planned increase of the shovel and truck fleet of only 50 per cent. This will be achieved through improved shovel and truck utilisation and productivity. In early 2005 Aitik started projects to enhance the utilisation of truck engine hours and to reduce fuel consumption. Both projects were successful, within a year efficient2 utilisation of engine hours increased from 60 per cent to 75 per cent and fuel consumption was reduced by six to eight per cent. The truck utilisation project focused on minimising idle truck hours by for example four operators on three trucks thus reducing idle engine hours to minimise lost time for breaks and shift changes. Other measures included focusing on improved dispatch usage, parking trucks when overtrucked, etc. Eco-driving was a project together with Swedish Road Administration with the objective to combine economical and environmental savings. To keep the focus on eco-driving a reward was set up for the shift team with the lowest fuel rate over rolling 15 weeks periods. Both activities included a comprehensive training program for mine foremen, dispatchers and truck operators focusing on efficient use of trucks from economic driving to optimised truck dispatching and minimising idle engine hours. Online monitoring of trucks activities and fuel consumption combined with continuous reporting gave shift foremen and management a tool to discuss and follow trends and individual shift team performance. The combination of close monitoring of mainly organisational practices and operator training resulted in significant productivity increase and lower operating costs without any capital investments.

Jan 1, 2007

By B. S. -J. Kang, M. A. Alvin, J. M. Tannenbaum

"A load-based micro-indentation technique has been developed for damage assessment and non-destructive spallation detection of TBCs at room temperature. This micro-indentation technology has been further extended to the development of a high temperature (HT) test methodology. Elastic modulus calibration tests performed on Hl 3 Tool Steel to 500°C and Haynes 230 at 1000°C displayed excellent agreement with reported values. Moreover, indentation creep tests of Haynes 230 at 1200°C were found to be in agreement with known creep exponents as well. Finally, a HT thermal flux indentation apparatus was assembled for conducting TBC turbine component testing under high temperature moisture-containing environments (= 50% steam with controlled gas content temperatures up to 1250°C). Description and design considerations of this test apparatus are discussed. Preliminary tests of ReneN5/MCrAlY/APS TBC coupons in steam/air environments with in-situ HT micro-indentation testing are conducted. Furthermore, the coupon is removed and examined for damage assessment at periodical intervals.IntroductionLoad and depth relationships acquired throughout the indentation process provide insight to material mechanical properties such as elastic modulus and hardness. Unloading segment analysis of these load displacement curves are utilized in the acquisition of a material's elastic properties. Yet, indentation tests are complex processes involving contact mechanics, material nonlinearity and even fracture mechanics. Thus exact analytical solutions for these processes are difficult to obtain. As a result, much of the current knowledge regarding the indentation process has been acquired through experimental methods and finite element simulations. Initial efforts by Tabor resulted in the application of spherical indentation to obtain post-yielding stress/strain relationships [1]. Soon thereafter, analytical load-depth relations for elastic indentation were developed [2], yet it was Lure who further derived the explicit relationships for both spherical and conical indenters [3]. Improving upon this, these interactions were later extended to indenters with various geometries by various researchers [ 4]. Additionally, by establishing the linearity of the initial unloading slope within the load-depth curve, a relationship between elastic indentation depth, maximum load, unloading slope and indenter geometry was established [5]. From this a theoretical method by which elastic modulus could be determined was established."

Jan 1, 2011