Search Documents

By Max R. Peña W

El crecimiento de la minería en el Perú requiere de un adecuado desarrollo tecnológico, así como de la reducción de costos en las mismas operaciones. Por ello, en la actualidad minera se desarrollan alternativas para la reducción de costos en perforación y voladura a través de las técnicas de corte escalonado y los detonadores eléctricos de alta precisión, a fin de obtener un mejor rendimiento en cuanto a su funcionamiento y precisión en minería subterránea y de cielo abierto.

Nov 24, 1993

By D. G. Chedgy

This article presents a novel design, called the Climax High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 -660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Jan 1, 1997

By C. E. Semler

A 5 year test program, involving on-line, in-vessel exposures at Barrick Goldstrike Mines. Inc. has provided valuable information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products have been evaluated. Properties before and after exposure are used to document the performance. Benefits have included the development of a new silicate mortar improved understanding of brick requirements and increased autoclave operating time between maintenance shut-downs. More improvements are expected in the future based on further information from the test program.

Jan 1, 1997

By Minjun Tang, Jianfeng Zhou, Feng Chen, Linjiang Qing, Xiaolei Song, Yufeng Guo, Tao Jiang

"Reduction swellability index (Rsn and low temperature reduction disintegration index (RDI) of vanadium-titanium magnetite oxidized pellets are harmful to the processing of ironmaking, for example, causing serious gas permeability, decreased yield, higher coke ratio and more furnace dust. Thus, the improvements of RSI and RDI of vanadium-titanium magnetite oxidized pellets were investigated in this paper, including the pretreatment of raw material, additives of dolomite or boric acid, pellets treated in chloride solution and so on. The results showed that damp milling as pretreatment and boric acid added in pelletizing were conducive to the RSI which decreased 5% and 7% respectively, while they were not efficient enough in improving RDI. Dolomite was efficient in improving RSI, but had negative effect on RDI. There was no evidence to show that RSI and RDI would be improved when pellets were treated in chloride solution. Pursuing this further, the mechanism of those improvements were investigated.IntroductionIn the world, vanadium-titanium magnetite utilization is investigated around how to recover iron, titanium, vanadium, and divided into blast-furnace method and non-blast-furnace method according to respective characteristics. Blast furnace method [1, 2] can recover iron and vanadium effectively, but Ti02 cannot be recycled. Non-blast-furnace methods include rotary kiln-electric furnace method, pre-reduction electric furnace method, reduction- grinding method and sodium vanadium-rotary kiln-electric furnace method and so on. [3-7]Comparing to the Non-blast-furnace method, the method of blast furnace smelting has been put into industrial applications. And it has the following advantages: First of all, effective recycling iron and vanadium; Second, technical problems of high titanium slag in blast furnace smelting; Third, it has mature technology in blast furnace smelting."

Jan 1, 2013

By Raj P. Singh

Applications of cementation in the recovery of metal ions from process solutions have been known for a long time. Cementation reactions involve electrochemical precipitation of a noble metal from solutions of its salts on a more electropositive metal which, in tum, progressively dissolves. For example, addition of zinc metal powder in a solution containing zinc and cobalt ions would allow for the precipitation (separation) of cobalt according to the following chemical reaction. This paper pertains to the recovery of cobalt from cobalt process solutions via a cementation reaction on aluminum shavings (metal scraps from cans etc). Specifically, we report on the characterization of cobalt process solutions, a by-product obtained from cobalt chemicals, and the kinetics of cobalt, nickel and manganese cementation from process solutions on aluminum shavings.

Jan 1, 2000

By D J. Clark, R F. Wright, M D. Goodz

The A1 Gold Mine is a Devonian-age narrow vein high-grade gold deposit located 115 km east of Melbourne. The mine operated almost continuously from 1861 to 1992 producing 442 334 ounces of gold (13.8 t) from 530 436 tonnes from primary gold ore tonnes processed at an average recovered grade of 25.9 g/t Au. The A1 dyke was attributed with a yield exceeding 620 000 ounces (19.3 t) of gold (including gold in alluvial and tailings deposits), and was renowned as one of VictoriaÆs premier mines paying considerable dividends. The orebody was principally in a diorite dyke bulge 150 m long, 45 m wide and 700 m deep and was mined via two vertical shafts. The mine site was closed in 1992 and the site was rehabilitated in 1999. In 2008 - 2009, a diamond drilling program identified various extensions to the host dyke lithology and to gold-bearing quartz vein filled fault zones over a 700 m strike length. The outcome of this study was the establishment of a mine geology corridor four times longer in strike length than the original 1970s model. This opens A1 dyke hosted deposit style to exploration outside the historical dyke bulge and provides exploration opportunity for all similar deposits. Construction of the first 3D geological model has developed new insights on the host rock diorite dyke system and identified various extensions to both host stratigraphy and to gold-bearing mineralised structures. Coarse visible gold in quartz vein mineralisation (>30 g/t Au) and medium-grade stockwork mineralisation (8 - 15 g/t Au) has been intersected within 100 m of the surface and up to 300 m along strike of the nearest historical underground workings. At depth it appears that the mineralisation is continuous with the main dyke body with consideration of minor rotation in the strike orientation and limited reverse thrust faulting showing maximum displacement of 10 - 20 m. Along the A1 mine corridor, between two and five parallel dykes are observed at different drill sections. The gold mineralisation is hosted mainly within the dyke rocks, but where the sedimentary rocks are intensely silicified or are xenolith rafts, the gold mineralisation continues across these sedimentary rock blocks. There has been inference to the role of silicified sedimentary rocks as a second ore host and a bounding material for inflections in fault and vein orientations. In the central 150 m long A1 mine dyke bulge, the extremities are demarcated by four to five parallel dyke fingers (referred to as apophyses) going both north and south. These apophyses are clearly observed both vertically and horizontally between levels No 4 and No 9. The dyke fingers entrap sedimentary rock xenoliths and collectively form the A1 dyke æcorridorÆ, which is quite uniform in overall width from the easternmost contact (footwall) to the westernmost contact (hanging wall). Dyke fingers were assumed to coalesce at depth into a single dyke, but recent drilling shows this feature to repeat in several positions with depth and along strike. Key observations are the relationship between gold grade and fracture density, alteration, sulfidation, host rock morphology û relation of contact shape and fault zones. These relationships allow for the classification of prospectivity indicators and geology as a guide to potential extensions of mineralised zones. Mining geology is contributing to the whole-of-mine life planning and development where decline path, stockpile and infrastructure positions are controlled by geology.

Jan 1, 2009

By G. Dodbiba, T. Fujita, M. Kawata, S. Yamasaki, K. Mitsuhashi, J. Ponou, Y. Iwazaki, T. Atarashi

"The grade of copper ore and concentrate is recently decreasing and it will continues decrease further in the future. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper concentrate is becoming even more important. In this work, the magnetic separation of copper concentrate by heat treatment and the flotation of low grade copper ore by microwave irradiation was studied. The heat treatment of copper minerals in the air atmosphere, the magnetization of most copper minerals increases and especially the magnetization of chalcopyrite shows the largest magnetization, after being heated at 500 oC. The wet HGMS of copper concentrate has been studied and the results have then been compared with the ones when calcined concentrate was used instead. The microwave treatment before ball milling increased the degree of liberation up to 100%, especially when compared with the case when only ball mill was applied to the as-received ore. The flotation of ground copper ore after microwave irradiation showed that the grade copper minerals such as chalcosite and bornite in froth part is much larger than that of tailing part.INTRODUCTION The copper has been used many kind of technological fields and will be more important for the future technology. The global copper production from mine is predicted as shown in Figure 1 (Northey, S. 2014). The copper production peak will be appeared in 2030 and the demand peaks in 2040. In the future the recycling of stocked copper and copper alloy will be necessary to satisfy the demand (Yoshimura, A. 2018). Changes in the grade of copper in copper concentrate, exported from several countries are shown in Figure 2. The copper grade in copper concentrate after mineral processing is gradually decreases every year and it is less than 30% nowadays. On the other hand, the copper ore grade change and prediction are shown in Figure 3. The grade of copper ore is also decreasing to less than 1% in 2010 (Northey, S. 2014). In the future the copper grade gradually decreases, reaching to less than 0.5% in 2080 and the energy to produce the copper metal will increase. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper minerals become more important, nowadays. The microwave irradiation of copper ore for the liberation, energy etc. has been reported by several researchers (for example, Batchelor, A.R. 2017). The magnetization change of copper ore by heating has been reported to remove the arsenic (Sawada, M 2015). In this report, the magnetic separation of copper concentrate by heat treatment and the flotation of copper concentrate by microwave irradiation are discussed after the characteristics of secondary copper minerals are investigated by these treatments."

Jan 1, 2018

By F. G. Smith

A few years ago, the writer encountered a problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Mathewson and Phillipsll an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-mm. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures. Preparation of Specimens The material used was cartridge brass 0.400 in. thick, having the following composition: Copper 66.60 per. cent., zinc 33.35 per cent., lead 0.02 per cent., iron 0.03 per cent. This was rolled with 35 per cent. reduction after a 700" C. anneal. Fig. 1 shows the structure of this original bar on which all subsequent anneals were made. Pieces 1 in. (2.5 cm.) wide and 3 in. long were prepared and annealed for 1/2 hr. at 450°, 550°, 650°, '750°, and 850" C. Each of these pieces are indented under the Brinell test with a 10-mm. ball at 500, 1000, 2000, and 3000 kg. pressure. Then, sets of five pieces from each of the original anneals were reannealed at 450°, 550°, 650°, 750°, and 850" C.

Jan 1, 1921

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto's Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology's photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012

By Aarón Morales

Este artículo se orienta hacia un aggiornamento de la minería en sus conceptos esenciales, con aportes en tres aspectos: una nueva definición de “resultados”, una propuesta para un nuevo formato del Estado de Resultados (P&G), y una invitación a revelar dos hechos fundamentales que permanecen fuera de la información oficial externa e interna. De acuerdo con el autor, cambiar los enfoques basados en volúmenes por lo que él denomina y describe como factor “f”, eliminará las distorsiones generadas por la aleatoriedad de los precios y convertirá a la empresa en un sistema unificado.

Nov 30, 2020

By G. R. Hopkins

The petroleum-refining industry established a new record in fuel efficiency at refineries in 1936, when 597,000 B. t. u. of heat were required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the "indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio (crude runs divided by capacity) for refineries increases toward the maximum of 100 percent, the fuel requirements show progressively smaller increases and the average E. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By Jeff Mattern

"Slope performance monitoring, dependable operational practices and ongoing collection of geologic data in openpit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike openpit has been ongoing since the early 1980s, having its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls.While technology can be efficient, interesting for collecting needed data, slope design fundamentals based on that data can be applied to create much added value.With the proper available equipment, steepening of bench face angles via presplit blasting is not an uncommon method for steepening of interramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted, resulting in quantified, rock-specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2° on a 305- m (1,000-ft) high slope, without the necessary purchases and procedural changes that would be required for presplit drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves.LocationThe Goldstrike openpit is located in the Great Basin, on the northern end of the Carlin Trend gold belt in northeastern Nevada (Fig. 1). The mine has produced more than 1.2 kt (43 million oz) of gold during the past 30 years."

Dec 1, 2018

By B Bonfils, P Lois Morales, C Evans

One of the main challenges for current and future mining and processing methodologies is to understand the characteristics of the rock so that its behaviour in one or more parts of the mining process chain can be predicted. Features such as rock texture, mineralogy or border complexity between minerals control how the rock behaves from the processing plant through to the final products, including tailings disposal and thus can affect the feasibility of the project from technical, economic and environmental impact perspectives. Understanding how the mineralogy and texture of rock affect its behaviour in mineral processing is a demanding area of research and is essential knowledge in predicting the processability of complex ores in different stages. This study aims to demonstrate that different types of relevant information can be extracted from a range of currently available analytical methods. However, this information can be used in a complementary way for building a more comprehensive rock characterisation at the microscale and better-predicting ore processing characteristics from the intact rock through to tailing disposal. CITATION: Lois Morales, P, Evans, C and Bonfils, B, 2018. Multisource rock characterisation at microscale for a better understanding of processing characteristics, in Proceedings Complex Orebodies Conference 2018, pp 44–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By N. Tounsi

The use of analytical modeling of continuous chip formation in conjunction with orthogonal cutting experiments was presented in the open literature to identify the coefficients of material constitutive equation within the practical range of stress, strain, strain rate, and temperature encountered in metal cutting. Identification of reliable constitutive data was hampered by a lack of a reliable model for the prediction of the primary shear zone thickness that affects directly the effective strain rate field. An original analytical model to determine the primary shear zone thickness is proposed in this paper. It is based on the mechanics governing the material flow in the primary shear zone. Based on the distribution of the hydrostatic pressure and the forces measured from orthogonal cutting tests, the model that describes the thickness of the primary shear zone is derived. To validate the model, FE simulations of chip formation using DEFORM3D were carried out for different materials and cutting conditions. The results of the analytical model are in reasonable agreement with FEM results.

Jan 1, 2006

By K. H. Nimerick

A unique freeze conditioning agent (FCA) which functions by forming structurally weak ice rather than suppressing the freezing point of water has been successful in alleviating frozen coal problems. Frozen coal treated with FCA has been quickly unloaded at temperatures below -17.SoC (O°F). Other areas where FCA has found utility has been de-icing conveyor belts, idler, idler arms and other moving parts that have been impeded by ice.

Jan 1, 1977

By Sven Petersen, Iain J. Stobbs, Bramley J. Murton, Paul A. J. Lusty

"INTRODUCTIONIt is widely thought that seafloor massive sulphide (SMS) deposits, the modern analogue of volcanogenic massive sulphide (VMS) deposits, present a potential global resource for base (Cu, Zn) and precious metals (Au, Ag). In addition, SMS deposits can be enriched in ‘critical metals’ including Se, Te, Tl [1], which are essential for use in the construction of modern and green technologies. Globally over 340 high temperature hydrothermal sites have been identified at a range of ocean spreading centres [2], significant massive sulphide deposit formation has been recorded at 165 of these sites [3].To date only 13 deep sea sulphide deposits have undergone intrusive investigation (drilling or coring) and of these, only 6 sites have published tonnage estimates [2]. Almost all research and drilling of SMS deposits has been focused on active systems, the investigation of the morphology, subsurface structure and mineralogy of hydrothermally extinct seafloor massive sulphide (eSMS) deposits is almost non-existent.As such, little is known about the mechanisms that operate post-SMS formation and which have an impact on the preservation and hence resource value of SMS. Identifying these generic processes and mechanisms, and the extent to which they impact the resource grade, is critical in evaluating the global potential of SMS."

Jan 1, 2017

By L. X. Zeng

The low-grade nickel resource is very abundant in the western China. To make the best of the low grade nickel ore, we studied the process mineralogy and beneficiation process of nickel ore in the Yangliuping of Sichuan province. The grade of nickel is 0.45% in the nickel ore and the nickel exists in the sulfide including pyrrhotite, nickel pyrite, chalcopyrite primarily. The nickel distributes in pentlandite and magnetite over 90% and the copper does in the chalcopyrite over 95%. The carri-er minerals of useful elements tend to concentrate in space for concentration. As is shown in grain-size analysis of three major minerals, there are some more fine-grained grains with the percent of from 10% to 15% (<40 µm) and from 3.5% to 5.5% (<20 µm). So there will be some smaller size disseminated sulfide minerals difficulty to liberate in the process of concentration. The liberation degree of sulfide is not high and there are much associativity in the sulfides. Therefore, we should reclaim the sulfide aggregation dominating as pentlandite when concentrating. In addition, the sulphide minerals is so brittle that we should take care of preventing from crashing when grinding. The gangue mineral is mostly metamorphic mineral including serpentine, chlorite and amphibole which is easy to be argillization and difficult to concentrate.

Jan 1, 2014

By Y. Fukunaka, M. Niinae, E. Kusaka, T. Kuzuya, R. Ishii

"Samarium oxalattr particles was precipitated in oxalic acid aqueous solution from samarium-loaded D2EHPA solution emulsified with a conventional impeller. The calculated fractional precipitation of samarium oxalate was reasonably compared with the value determined by chemical analysis. Morphological variation of oxalate precipitate particles was then examined with H2C2O4 concentration in aqueous solution, Sm(III) and D2EHPA concentrations in organic phase. The needle-like precipitate was identified as Sm2(C2O4)3 10H2O by XRD. Precipitates obtained at higher H2C2O4· or Sm(III) concentration greatly decreased the length of major axis of precipitate, while those at higher D2EHPA concentration increased it. The oxalate was further precipitated under ultrasonic irradiation. However, the morphological variation caused by theses processing variables was not so evident under ultrasonic irradiation as in an impeller or shaking mixer.IntroductionThe materials processing of the rare earth elements must be reviewed from the scope of industrial ecology, since they have the potential applications of magnetic materials as well as secondary battery in developing programs of the electric vehicle. The technological trend to develop the electric vehicle may greatly influence the concept of materials processing, since the global· environmental problem must accommodate with the sustainable development for mankind. The recycle design must be a key issue in the materials science and engineering.Solvent extraction provides a unique separation technology -in this sense. Doyle (1)(2) reported the integrating solvent extraction with processing of advanced ceramic materials, whose chemical composition and microstructure must be precisely controlled. In her paper, the higher productivity inherent to the present process superior to hydrolyzing metal alkoxides was emphasized. Oxalic acid has been used as precipitant for rare earth purification process, since rare earth oxalate has a very small solubility in water and can be easily decomposed to oxide. It is thus suitable for precipitation stripping agent in cationic exchange type extracting system (i.e. D2EHPA, VA-10, PC-88A and so on)."

Jan 1, 2000

By R. A. Wyman

A comparison of the amount of minus-28-mesh product produced by a standard grinding test procedure is provided for 45 non-metallic materials. The percentage of product, the weight of product per unit of energy used and the weight of product per mill revolution are shown. The results exhibited excellent reproducibility and demonstrated an accurate comparison of grindability for non-metallic materials.

Jan 1, 1977

By V. K. Banakar

The occurrence of hydrogenous ferromanganese encrustations (Fe-Mn crusts) on the Cretaceous age Afanasiy-Nikitin Seamounts (ANS) in the eastern Equatorial Indian Ocean (EEIO) was first reported by Banakar et al. (1997, Marine Geology). The major element composition of the samples from the upper flank of the ANS (~1650 m water depth) indicated enrichment of Co up to 0.9 % (Parthiban and Banakar, 1999, Indian Mineralogist). Subsequently a project supported by the Department of Ocean Development to explore the ANS for Co-enriched Fe-Mn crusts was launched in 2002 by the National Institute of Oceanography. Sampling at regular depth intervals along two transects on the slopes of the northern elevated region of the ANS was carried out. The Fe-Mn oxide deposition is evident on almost all types of substrates viz., basalts, conglomerate limestone, fossil corals etc., and the thickness of the oxide layer varies from a patina to 7 cm. The Fe-Mn crust growth is evident only above a water depth of 3200 m, below which semi-lithified carbonate ooze is dominant. The ANS Fe-Mn crusts from all the water depths exhibit Mn/Fe < 1.5 suggesting pure hydrogenetic accumulation of metal-hydroxides. Bulk sample Ce-contents for a few selected depth-representative samples are remarkably high, up to 3700 ppm with an average of ~2500 ppm. The positive Ce-anomaly decreases from ~8 at 1600 m depth to ~1.6 at 3200 m depth, which is in contrast to the modern dissolved oxygen depth-profile in the region. This observation suggests that major time-period of the Fe-Mn crust accretion history is dominated by ambient waters with lower-oxygen at deeper depths than at the intermediate depths. This in turn probably suggests a major reorganization in the deep-intermediate hydrography of the region in the past.

Jan 1, 2005