Search Documents

By Andre Zingano

An underground mine using room and pillar and retreat mining methods was developed during the 1950?s. In 2009 an open cast mine was opened in the same reserve with the objective of mining five coal seams including the one previously mined. Recently, a series of slope failures were detected at the open cast mine. The surface mine map was overlain on the underground mine map, and it was observed that the slope failures were located above a retreat mined area where the overburden had caved and the ground subsided. The deformation and displacement attributable to subsidence caused a loss of strength in the overburden strata. The objective of this paper is to study the causes of slope sliding (or failure) due to the ground subsidence of rock layers above oldmined out areas. A map was created to overlay the two mines -- the abandoned underground mine and the active surface mining. Two- and three-dimension numerical modeling was conducted to simulate the slope behavior and to verify whether the mine subsidence was the cause of slope instability. This study indicated that the subsided rock layers were the cause of slope instability and sliding.

Jan 1, 2013

By F. E. Cash

Among petroleum refinery employees and officials throughout the United States there has been marked effort to reduce accident frequency and severity. For the interest and benefit of refineries both in Louisiana and in other petroleum-refining States it has been possible to obtain from five refineries, representing 70 per cent of the production of Louisiana, tae accident experience for the past 3 to 6 years. The companies concerned have requested that their names be not used. For tide reason the four plants listed and discussed are designated as refineries A, E, C, and D. The size of the plant as regards largest to smallest number of employees is indicated by the alphabetical order.

Jan 1, 1933

By Lizbeth A. Escobar, Phol M. Llanos, Maritza Y. Avila

The present research develops the estimation of critical parameters such as the distances and times between holes to avoid failure due to dynamic pressure in electronic detonators based on the near-field ground vibration model of Holmberg & Persson and the hydrodynamic model of Neyman.

Feb 1, 2020

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes.

Feb 1, 2020

By Kleiton dos Santos Melo

As fibras de bambu são ricas em celulose, hemicelulose e lignina. Elas apresentam altos módulos de elasticidade e alta resistência mecânica, o que as tornam bastante eficazes como reforço em compósitos. Com o intuito de aprimorar as propriedades mecânicas de materiais poliméricos em escalas diminutas, tem-se buscado a aplicação desses reforços em sua forma nano. A extração de nanocelulose tem sido bastante estudada e, em nosso trabalho, foram feitas adaptações de métodos que mostraram-se mais eficazes. Os nanowhiskers a base de bambu foram obtidos por hidrólise ácida a 64%, após tratamento químico prévio de limpeza e branqueamento. Os materiais obtidos foram então caracterizados por FTIR, TG, DTG e tamanho de partícula por Potencial Zeta, onde seus resultados indicaram que o método de produção utilizado foi eficaz.

Aug 17, 2017

By Anna Carolina Cerqueira Neves

As fibras sintéticas vêm sendo gradualmente substituídas por fibras naturais. Em comparação com a fibra sintética, fibra natural demonstrou vantagens econômicas e ambientais. Visto que apresenta características interfaciais com matrizes poliméricas que favorecem a absorção de energia de alto impacto pela estrutura. No entanto, até agora pouco foi avaliado sobre a fibra de cânhamo incorporada em matrizes poliméricas. Este estudo tem o objetivo de avaliar a resistência ao impacto deste tipo de compósito com matriz de poliéster reforçada com diferentes porcentagens de fibras de cânhamo. A resistência ao impacto aumenta proporcionalmente com a quantidade relativa de fibras incorporadas como reforço na matriz polimérica. Este desempenho foi relacionado com a dificuldade de ruptura imposta pelas fibras, resultante da interação da matriz de fibra de cânhamo / poliéster de forma a ajudar a absorção da energia de impacto.

Aug 17, 2017

By Marcela Alves Silva

Aços inoxidáveis são ligas Fe-C-Cr com elevada resistência à corrosão. Estes podem receber diferentes elementos de liga, que alteram suas microestruturas e propriedades de acordo com o interesse da aplicação. Os mais comuns são os austeníticos, ferríticos, martensíticos e duplex. Os aços inoxidáveis austeníticos possuem excelente resistência à corrosão, elevada ductilidade, boa soldabilidade, conformabilidade e tenacidade. Os aços inoxidáveis ferríticos possuem boa resistência à corrosão, são bons para estampagem e possuem maior dureza e soldabilidade em relação aos austeníticos. Os aços inoxidáveis duplex (AID) são aços com estrutura bifásica, formados pelas fases ferrita e austenita, em proporções de aproximadamente 50% de cada. Os AIDs apresentam associação de resistência mecânica com resistência à corrosão. O presente trabalho tem como objetivo realizar ensaios metalográficos e tração de um AID 399B, de um aço inoxidável ferrítico 441A e de um aço inoxidável austenítico 304N, para fins de comparação da microestrutura e propriedades mecânicas. Com os resultados conclui-se que o AID possui maior resistência à dureza na escala HRB, o aço austenítico possui maior capacidade de alongamento, devido sua estrutura CFC. Já o limite de resistência e de escoamento são maiores no aço AID devido a sua maior proporção da fase ferrita (52%).

Aug 17, 2017

By Bruno Veiga Fontana

O uso do nitrogênio como gás de injeção através de plug poroso no forno panela pode ser importante do ponto de vista econômico, no entanto pode provocar pick-up excessivo de nitrogênio caso seja realizado de forma inadequada. No presente trabalho, são apresentados os resultados de testes de injeção de nitrogênio e nitrogênio seguido de argônio em aços para produtos longos. Visando compreender os processos de absorção e sua cinética, um modelo cinético é formulado e ajustado aos dados experimentais. O modelo cinético clássico descreve bem os resultados experimentais e permite o uso para previsões do efeito da injeção de nitrogênio sobre o teor de nitrogênio no aço. Observa-se que a cinética de absorção é controlada pela agitação da panela e pela presença de elementos tenso-ativos, notadamente o oxigênio, como esperado, de acordo com os modelos clássicos do fenômeno. A técnica da injeção de nitrogênio seguida de argônio é bem-sucedida economicamente e o modelo permite a previsão e o controle da absorção de nitrogênio pelo aço.

Aug 17, 2017

By Bárbara Dornelas de Assis

Minérios de manganês são uma importante fonte de matéria-prima para a siderurgia. Desse modo, o desenvolvimento de trabalhos de caracterização para melhor compreensão da composição e o comportamento desses minérios é de suma importância. O presente trabalho teve como objetivo a caracterização física, química, mineralógica e a análise do comportamento de crepitação do produto granulado de minério de manganês de uma mina da região de Dom Silvério no estado de Minas Gerais. Cerca de 77% do produto granulado encontra-se entre 50 e 6,3mm. O minério de manganês é composto pelas fases minerais manganita, pirocroita, groutelita, birnessita, siderofilita e calcopirita. Os teores dos elementos majoritários Mn, Fe e SiO2 foram, respectivamente, 24,04%, 8,89% e 15,57%. A densidade estrutural da amostra é de 3,25 g/cm³ e sua área superficial, 6,8 m²/g. O ensaio de crepitação realizado mostrou que o índice desse fenômeno para a amostra com umidade natural é de 8,82% e se encontra próximo dos índices de crepitação de minérios de manganês atualmente comercializados no Brasil. A secagem da amostra não reduziu de forma significativa os índices de crepitação no minério.

Aug 17, 2017

By Victor Caso Moreira

Neste trabalho é estudado o efeito do ferro no tamanho de grão e nas propriedades mecânicas do latão UNS C26000, também comercialmente conhecido como latão 70/30. Foram avaliados dois teores residuais: 0,0069% e 0,0592%. As amostras foram inicialmente laminadas até a espessura de 2,30 mm, submetidas a tratamento térmico de recozimento objetivando tamanho de grão de 0,030 mm. Posteriormente as amostras foram laminadas para outras três espessuras e submetidas a um novo recozimento. As amostras recozidas passaram por análise de tamanho de grão e foram submetidas a ensaios de tração, sendo obtidos resultados de limite de resistência à tração. Os comportamentos apresentados pelos materiais foram distintos entre si, sendo que o material com maior teor de ferro apresentou aumento das propriedades mecânicas em função do aumento da redução de espessura e o material com menor teor ferro apresentou redução do limite de resistência à tração. Quanto ao tamanho de grão, o material com menor teor de ferro apresentou pequena variação de tamanho de grão após o recozimento, enquanto o material com maior teor de ferro apresentou redução do tamanho de grão em função do aumento da redução de espessura, demonstrando inibição do crescimento de grão e estrutura heterogênea.

Aug 17, 2017

By Bing Li, Miao Shen, Qiang Wang, Yuqi Chen

Electrochemical methods including cyclic voltammograms, square wave voltammograms, chronopotentiometry are applied to characterize the reduction potentials of Na+ and Li+ ions in LiCl-KCl melts. According to theoretical calculation, the reduction potential for Na+ is slightly more negative than Li+ in NaCl-LiCl-KCl melts at 450℃. However, by electrochemical measurements, the reduction potential of Na+ is slightly more positive than Li+ in the above melt and the potential difference between Na+ and Li+ reaches 0.16-0.2V on an inert W electrode in 1.0-2.0 wt% NaCl-LiCl-KCl melts. An active Pb electrode is used to improve the removal rate of Na+ from LiCl-KCl melts. The reduction potentials for both Na+ ions and Li+ ions on a Pb electrode shift to more positive values and the reduction currents become larger. After 6h electrolysis on a Pb electrode at -3.0V, the practical removal efficiency of Na+ ions reaches 90.12% and the reduced products contain metallic Na and Li with a Na/Li mass ratio of 4.25/1.

Jan 1, 2015

By L. C. IlsLey, J. W. Paul, E. J. Gleim

Flame safety lamps have been used in gaseous mines since the Davy lamp was introduced, more than 100 years ago. During the last decade the flame safety lamp has been rapidly replaced by the electric lamp as a device for illuminating the miner's working place; in the United States the electric cap lamp has been widely adopted. For example, in 1911 approximately 45,000 flame lamps and no electric lamps were being used in the Pennsylvania bituminous mines, which were then producing 35 per cent of all the soft coal mined in this country; by 1918 the flame lamps had decreased to 17,000, whereas electric lamps-mostly of one maketotaled nearly 48,000. In Great Britain during the same years the total of 723,934 flame lamps decreased to 590,185 and the electric lamps gained rapidly from 4,298 to 156,521. No later reliable figures are at hand. However, before the flame lamp becomes obsolete, it is fitting that the Bureau of Mines compile a permanent record of a device which has served the mining industry for more than three generations, and not only made possible the development of entire districts that otherwise could not have been worked but undoubtedly saved the lives of thousands of underground workers. Flame safety lamps are capable of doing more than the name indicates. First, under normal conditions, they can be used in a mine atmosphere that contains an explosive mixture of gas and air without great danger of exploding such a mixture, though such use of a flame lamp should not be permitted. Second, to an experienced man they indicate percentages of gas much lower than the explosive limit, and thus can be used to indicate to workers the approach of an unsafe condition in the mine atmosphere. Third, flame lamps will not burn in an atmosphere greatly deficient in oxygen, and they therefore warn the users of such deficiency in time to withdraw to a place of safety. Flame safety lamps are still used rather widely in the United States for general illumination and to a still greater extent for detecting gas. Many coal-producing States require fire bosses to use these lamps in gaseous mines, and the regulations of several States specify that a gIven number of such lamps be kept available for emergency service.

Jan 1, 1924

By Oliver Bowles

The manufacture of lime is one of the oldest industries. Plants are distributed widely and furnish an essential raw material for numerous industries. The use of lime by the building trades, in agriculture, and in hundreds of manufacturing and chemical processes has created demands for a large production and has necessitated exhaustive research on methods of manufacture and uses. The bibliography of lime is an extensive one, but for the most part each publication has dealt with only certain operations. The purpose of this paper is to present a general picture of the industry as a whole. The abundant literature has been abstracted and quoted freely, and the National Lime Association has rendered valuable assistance in furnishing data for certain sections. Publications containing more detailed information on the various branches of the industry are referred to in the footnotes and in the bibliography.

Jan 1, 1936

By S. J. Hussey

Since the discovery in 1935 by Adams and Holmes that certain synthetic resins exhibit ion-exchange properties, many applications of the ion-exchange process have been made. There are two general types of ion-exchange resins. Cation exchange resins adsorb cations from solution, and these in turn may be replaced by other cations adsorbed under certain conditions. 'Anion exchange resins adsorb acids from solution, and the anion of the acid may then be replaced by other anions. It is reported, however, that certain anion exchange resins have a low capacity for anions of weak acids without the necessity of acid adsorption either directly or as an intermediate step. The adsorbed ions may then be removed from the resins by elution with an appropriate solution, and the resin is prepared for the next adsorption cycle by regeneration with another solution. Sometimes one solution, is used to simultaneously perform the functions of elution and regeneration. The first and probably the largest application is in the field of water purification. Other applications have been made in the production of high-quality foods for human consumption, in the recovery of valuable substances from solutions, in the separation or fractionation of electrolytes, and in several other fields, each of which has its specific applications, variations, and possibilities. Ion exchange resins also have been highly useful in perfecting techniques of laboratory analysis and research.4/, 5/, 6/

Jan 1, 1948

By David Schlain

The galvanic corrosion properties of titanium and zirconium were investigated by the Bureau of Mines. The dissimilar metals involved in these experiments included magnesium, magnesium alloy FS1, aluminum alloys, zinc, steel, tin, lead, copper, Monel, nickel, and several stainless steels. Couples were immersed in synthetic ocean water, tap water, 5-percent ammonium sulfate solution, 5-1/2-percent sodium chloride solution, sodium hydroxide solution, 0.1 N hydrochloric acid, and various concentrations of sulfuric acid.

Jan 1, 1956

By Lloyd B. Underwood

In the event of a sudden nuclear attack upon the United States, it is imperative that vital command and control centers have a high probability of survival. One such vital facility is the North American Air Defense Command Combat Operations Center at Colorado Springs, Colorado. Known briefly as NOW, this installation when completed will be housed in large chambers excavated out of granite beneath the eastern slope of Cheyenne Mountain (Figure 1). The NORAD COC, a U. S. Air Force sponsored project, will serve as the primary collection and evaluation center for data concerning unknown aircraft, missiles, or space vehicles, which might bring destruction to North America. The data will be fed into high-speed computers and electronic equipment from outpost sources - radar, ballistic missile early warning stations and picket ships throughout the world. Electronically controlled display boards will make it possible to evaluate the tracking data instantaneously and to take appropriate defensive action1.

Jan 1, 1965

By D. E. Sullivan

The Bureau of Mines investigated the availability of potash from 68 mines and deposits in 12 market economy countries (MEC's) containing, at the demonstrated resource level, approximately 11.7 billion metric tons (mt) of potash in assay terms of contained K2O; K2O as used by industry as a standard of comparison for the different forms of potash. These resources include almost 190 million mt in the United States, 9.63 billion mt in Canada, approximately 430 million mt in Western Europe (France, Federal Republic of Germany, Italy, Spain, and the United Kingdom), 1.24 billion mt in the Middle East (Israel and Jordan) and over 220 million mt in other countries (Brazil, Chile, and the Congo). This analysis his determined that future production of potash in MEC?s will most likely continue to be from the large resources associated with producing operations in Canada. Based solely on the demonstrated resources included in this study, potash mining in the United States would decline while overseas production from MEC's can continue into the next century at near current production levels. However, timely development of new or inferred resources would offset any such decline. Producing mines in Canada have the resources to increase and maintain increased production well into the next century. For U.S. potash users, Canada is a long-term stable and secure source.

Jan 1, 1986

By Donald Giroux

This report documents the design, fabrication, testing, and coal mine demonstration of a hopper-feeder-bolter during a four-phase program for the U.S. Bureau of Mines. The machine was designed to increase productivity and safety in under-ground room-and-pillar mining. It performed well as a hopper-feeder for continuous haulage during a coal mine demonstration. Testing in a simulated mine showed that the machine also has good roof bolting capability.

Jan 1, 1987

By J. H. Holden

The Federal Bureau of Mines is doing research and development work on a pressure-gasification pilot plant for producing synthesis gas directly from pulverized coal, oxygen, and steam. A pressure-gasification pilot plant has been constructed, and an investigation was made with the following basic objectives: 1. Determining the effect of varying pressure (75, 100, 150, and 300 p.s.i.g.), coal rate (400, 700, and 1,000 pounds per hour), and oxygen-to-coal ratio (8 to 11 std, c,f. per pound), on percentage of carbon gasified, oxygen and coal requirements per unit of CO + H2 produced, exit-gas temperature, and heat loss. The steam-to-coal ratio was maintained at approximately 0.3 pound per pound. 2. Development of a stabilized gasification zone or reaction space. 3. Improvement in operability of the pilot plant.

Jan 1, 1960

By J. R. Thoenen

This paper outlines briefly results of seismic measurements recorded in the vicinity of quarry blasting under practical operating conditions. The data cover field work done from January to the middle of August 1930, during which time records were made of 61 blasts in 19 quarries. Of the tests made, one was in biotite-gneiss, two in dolomite, two in a flintlike volcanic complex, three in gabbrodiorite, five in trap rock, and six in limestone. One quarry was in Alabama, two were in South Carolina, two in New York, four in Kentucky, five in Connecticut, and five in Massachusetts. Explosive charges ranged from 0.30 pound to 41,900 pounds, and the method of shooting varied from mud caps through hammer and wagon drill holes to churn drill holes and coyote tunnel shots.

Jan 1, 1937