Search Documents

Unrelieved residual strains can influence the states of stress in rock masses. If cheap, stable structures are to be constructed in Tock in which large pressures are exterted by unrelieved residual strains, the pressures must be either utilized or neutralized. A photoelastic technique has been used to show that the release of residual strains in rocks is influenced by the mechanical properties of anisotropic rock fabrics. The relationships between directions of residual strain release and the attitudes of minor geological structures have been determined. For engineering design purposes it is possible to estimate the principal stress directions in rock containing unrelieved residual strains if the attitudes of such minor geological structures as foliation planes, lineations, and joints are known.INTRODUCTIONQuarry workers have long been aware that near-surface rocks may be highly stressed. In many cases the stresses are too large to be the result of gravitational loads. Dale (1923, pp. 34-35) gives many instances of deformation produced by the violent release of residual strains in quarry rocks. Coates (1963) has described powerful rock bursts and cases of rock deformation underground implying the existence of much larger stresses than are likely to result from present-day gravitational loads. The only explanation is that pressures of up to several thousands of pounds per square inch may be caused by unrelieved residual strains in rock.Instruments have been developed for measuring states of stress in rock masses. Most stress determinations in rock have been made on the assumption that rock behaves as a simple elastic material. It is now known that rock is a...

Jan 1, 1964

By Mark A. Jirsa

The Biwabik Iron Formation is a ~1.9 billion year-old sequence of iron-rich sedimentary rocks that was metamorphosed at its eastern- most extent by ~1.1 billion year-old intrusions of the Duluth Complex. The metamorphic recrystallization of iron-formation locally produced iron-rich amphiboles and other fibrous iron-silicate minerals. The presence of these minerals in iron-formation along the eastern part of what is known as the Mesabi Iron Range, and their potential liberation by iron mining has raised environmental health concerns. We describe here the geologic setting and mineralogic composition of the Biwabik Iron Formation in and adjacent to the contact metamorphic aureole of the Duluth Complex. The effects of metamorphism are most pronounced within a few kilometers of the contact, and decrease progressively away from it. The contact aureole has been divided into four metamorphic zones?each characterized by the composition and crystal structure of the metamorphic minerals it contains. The recrystallization of iron-formation to iron-rich amphibole minerals (grunerite and cummingtonite) and iron-pyroxene minerals (hedenbergite and ferrohypersthene) is best developed in zones that are most proximal to the Duluth Complex contact. ©2007 Elsevier Inc. All rights reserved. Keywords: Iron-formation; Mining; Fibrous; Mineralogy; Metamorphism.

Jan 1, 2007

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin, Derek Maishman

Ground freezing was utilized to provide complete stability of the excavation face and complete groundwater cut-off for the jacking of the three tunnel boxes for the Interstate 90 / Interstate 93 approach to the Fort Point Channel crossing. Through a wide range of geological conditions and large buried obstructions, the freezing provided complete stability of the face so that a 11.5 m (38 ft) high free standing vertical face could be mined without the need for any additional face support. Obstructions were incorporated into the massive frozen ground matrix, and held in place so that they could be excavated with a minimum of disturbance. The freezing provided an absolute groundwater cut-off, and permitted the work to be done without disturbance to the active rail system immediately above. With the use of instrumentation such as borehole thermocouples, the effectiveness of the freezing was guaranteed and the jacking proceeded with complete confidence and assurance of the ground conditions ahead.

Jan 1, 2001

By Fred H. Perfect

The thermite process, now approximately 80 years old, has heretofore been practiced in ceramic vessels. This paper outlines the successful production of several million pounds of alloy produced in zuater-cooled copper vessels. THE high temperatures necessary to produce fluid high-alumina slags have probably discouraged earlier workers from attempting to utilize water-cooled vessels. The following is a report of the successful application of this method, together with a report of the physical and chemical problems which had to be solved to make the process practical. About 1955, when Reading Alloys was more concerned with the production of ferrotungsten than with most other types of alloys, it was found to be exceedingly difficult to predict the reaction rate that one would experience from one tungsten ore to another . This difficulty was increased for two reasons: the physical state of the ore as received was seldom uniform, and the size of the mass to be reduced is a very important factor in developing the proper mix for the final reaction rate and temperature. For example, the reduction of ferric oxide with aluminum would theoretically produce temperatures of about 2600°C, and, in spite of the losses due to radiation, the energy is quite sufficient to produce a very fluid slag and iron effecting a very clean separation. On the other hand, the reduction of ferrous oxide with aluminum, while it is not as energetic as the first reaction, nevertheless should give temperatures above 2000"C, which should cause separation of alumina and iron, but, in practice, this is not the case and good fluid slag is not obtained. The heat of reaction, calculated from the thermo-dynamic heats of formation of the constituents of the reaction, offers a convenient guide to the feasibility of a thermite reaction. Thus, the values listed in Table I can be used as an approximate guide for estimating the results which may be expected in the reduction of various oxides and combinations of oxides using aluminum as the reducing agent. As a generalization, those reactions releasing approximately 600 cal per g of total mass represent the lower limit at which to expect separation of slag and metal. On the other hand, those reactions which release 1100 to 1200 cal per g are too violent to be used successfully without the addition of considerable inert material, such as lime, fluorspar, and so forth. Reaction rate is also a very important factor. This, of course, is governed very largely by the sizing and intermingling of the oxidant and reductant and by the starting temperature of the reactants. This is why those figures shown in Table I can only be a general guide. Further, it must be understood, that by adding powerful oxidizing agents, such as nitrates, chlorates or metallic oxides, such as molybdenum trioxide or chromium trioxide, certain problems respecting low temperatures are not necessarily solved. This is true in the addition of oxidants, such as sodium chlorate. By adding too high a concentration of sodium chlorate as a booster for a particular reduction, explosions are generated. Generally, they are of an intermittent type so as to give a Roman Candle effect to the reduction itself; with each surge resulting from a minor explosion more and more material is thrown

Jan 1, 1968

The Calypso geothermal field, mapped by the R V Sonne (cruise SO-135) in 1998, includes four main sites, the Northern Vent Area (centred on 37¦ 36.7'S, 177¦ 06.2'E, area 1.5 km2), Central Vent Area (37¦ 39.4'S, 177¦ 05.2'E, 1 km2), Southern Vent Area (37¦ 41.7'S, 177¦ 06.0'E, 1 km2) and Mercury Vent Area (37¦ 41.3'S, 177¦ 07.3 'E, 0.5 km2). Hydrothermal activity at the vent sites is controlled by minor, sub-parallel NE-trending normal faults. Gas bubble trails (C02) and shimmering hot water vent from fractures and joints between large blocks of silicified volcaniclastics and in depressions in the sediments at the base of these outcrops. Measured maximum vent temperatures are between 180¦C and 201¦C. Venting fluids are at, or just below, boiling for water depths of 200 m. Rock samples recovered by dredge from the sites include massive anhydrite, clay-altered pumiceous ash, silicified volcaniclastic sediments and volcaniclastic breccias cemented by sulphur. Clay-altered samples, dominated by randomly interstratified illite-smectite and accessory chlorite, indicate formation environments of 70¦C to 90 ¦C. Native sulphur is abundant throughout the samples. Fine-grained (<1 mm) disseminated pyrite and vein pyrite occurs in the clay-altered pumiceous volcaniclastics and argillites. In the Southern and Mercury Vent Areas, fine-grained orpiment, realgar and cinnabar have deposited in the sandy matrix of volcaniclastic breccias. Amongst the cinnabar, small (<2 mm) beads of native Hg formed on the surface of several rocks following their recovery. These samples also contained abundant light hydrocarbons, which coat the rocks with an oily sheen.

Jan 1, 1999

By Nathaniel Arbiter

Flotation’s earliest patent was issued in 1860. However, the process was first applied commercially in Australia until 1904, and in Montana in 1911. Major advances followed both in reagent treatment and in cell design, with resulting process improvements. Mechanical cells have seen the widest use and with the major increases in plant capacities (Fig. 1) their volumes have also increased (Fig. 2). In 1991, the principal use for the process was to produce copper concentrates for smelting. It was applied to 243 Mt (268 million st) of copper ore. The total of all ores floated that year was 426 Mt (470million st). In 1997, US mines produced 257 Mt (284 million st) of copper ores for flotation, yielding1.75 Mt (1.94 million st) of copper.

Jan 1, 2000

By Khaled Morsy

In the past two decades, high horizontal stress has been attributed to many ground control failures. Most believe that entries parallel to the high horizontal stress is most stable and least stable when perpendicular to it. Entry stability decreases when the angle between entry and horizontal stress increases. The concept of 2-D stress shadow has been proposed for selection of proper panel orientation, often with mixed results. In this paper 3-D finite element modeling was used to analyze the stress distribution at the headgate of a longwall panel subject to high horizontal stress at various angles. It was found that the directions of induced principal stresses at the longwall face and headgate are independent of the panel orientation. The induced principal stresses concentrate or relief at headgate based on the panel orientation with respect to the directions of the induced principal stresses. Accordingly, only 3-D modeling can fully account for the effects of high horizontal stress on panel orientation. The paper illustrates in details the changes in orientation and magnitude of all three principal stresses around the longwall face and T-junction area as panel orientation changes.

Jan 1, 2006

By Tellis D. A

An outline is given of the general position of earthsciences information in Australia, the background to development of the Australian Earth Sciences Information System (AESIS) and the role of the Australian Mineral Foundation in developing and co-ordinating the projeot in co-operation with the CSIRO, BMR, National Library of Australia, AGIA, and many companies.Details 'of the system, method and anticipated rate of input (especially of unpublished material at which the System particularly aims), mode of dissemination, and use of the data base are discussed. Information on theAustralian Thesaurus of Earth Sciences and Related Terms and brief details of some 30 earth sciences information collections in Australia is given.

Jan 1, 1977

By D O’Dea, B Godel, T Honeyands, B Ellis, T Harvey

X-ray computed tomography (XCT) is a non-destructive technique that allows the exploration of the internal structure of solid objects in 3D. Over the past ten years, the combination of XCT with more conventional 2D techniques and quantitative 3D image processing and analysis (commonly referred to as digital rocks) has allowed us to address some of the most challenging problems in ore deposit studies. The range of X-ray energies used in XCT allows the X-rays to be transmitted through complex and dense materials including iron ores (eg sinters, lumps, granules). Recent high-resolution XCT scanners have the ability to generate multiscale (25 down to 0.3 µm voxel size) imaging of a given sample enabling the characterisation of 3D textures across a range of scales. This paper will focus on the application of digital rocks to iron ore sinter particles (using filtered polychromatic X-ray beam). The paper is divided into three parts and includes: i) details on the methodologies including their benefits and limitations and the effect of spatial resolution; (ii) the quantification of pore network topology and pore characteristics (eg open versus closed pores, pore size distribution and pore morphologies; degree of connectivity of the pore network and its tortuosity); and (iii) the evaluation of the technique to characterise various phases within the material and quantify 3D mineral textures.CITATION:Godel, B, Ellis, B, O’Dea, D, Honeyands, T and Harvey, T, 2017. Digital rocks for iron ore sinters – towards a D quantification of sinter textures, in Proceedings Iron Ore 2017, pp 529–534 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By L. Lacerda

Spray-on ground support membranes (GSM) or thin support liners hold today perhaps as much potential to impact underground (u/g) ground support operations as dry and later wet-mix shotcrete when introduced to mining in the latter part of the 20th century. This emerging technology has come a long way from the time the first single component experimental coatings were tested in the mid-1980s. Due to a number of factors, including occupational health risk and mine safety regulations, it has taken quite some time for the development of non-hazardous membrane products. However, at this junction most existing u/g mines that employ more conventional forms of ground support could benefit from evaluating GSM technology as a means of improving safety and the bottom line. The same is especially true for future mine developments. This paper describes Master Builders Inc.’s CS1251 GSM product and its implementation. It discusses the situations in which GSM may replace other forms of ground support. Furthermore, it evaluates GSM costs & safety issues and looks at present applications and the potentially bright future of this technology.

Jan 1, 2002

By R. Mohan Srivastava

"The goal of estimation is considered in the light of decision analysis. A simple example reveals the essential elements of decision-making in the face of uncertainty. A second example shows that these elements are also key features of many mining decisions. These two examples cause us to revive an old probabilistic notion that the goal of estimation should be to quantify what is unknown. The conditional probability distribution provides the complete statement of one's uncertainty. Once the conditional probability distribution has been established, one should retain as an estimate the value which minimizes some objective loss function. A third example shows how the ""best"" estimate depends on the chosen loss function. Current practice is almost exclusively based on the least squares method, which assumes a loss function which penalizes underestimation and overestimation equally. This is unfortunate not only because symmetry is an unrealistic assumption but also because mining offers a rare opportunity to state the loss function directly in terms of profitability. Both the theoretical framework and the practical tools exist to allow us to reconsider the conventional notion of the ""best"" estimate. IntroductionThis paper looks at estimation in the mining industry from the point-of-view of decision analysis. Virtually all decisions depend on estimates since few of the important parameters are ever known exactly. In this paper we will be referring mainly to the estimation of ore grades, though the approach discussed here is generally applicable to any decision in which relevant information is uncertain.In the first section we look at a very simple example of decision-making in the face of uncertainty. We will then tum to a mining example and see that the essential features of the simple example still pertain. From these two examples it will be clear that the decision analysis approach rests on two key concepts: the conditional probability distribution and the loss function. A third example demonstrates how different loss functions produce different ""best"" estimates from the same conditional probability distribution. In the final sections we willexamine the current practice of estimation in the mining industry. Though the tools for estimating the conditional probability distribution already exist, a change in the way we think about ""best"" estimates is needed. Very little attention is presently paid to the loss function even though it is readily available in many mining applications."

Jan 1, 1987

By Brian Khalighi, Massimo Franceschi, Giovanni Giacomin, Gianni Porta

Headrace Tunnels and parts of the Access Adit Tunnels of Kárahnjúkar Hydropower project, KAR-14, in Iceland will be excavated using three full-face Robbins Tunnel Boring Machines (TBM). TBM sizes range from 7.23 to 7.63 meters in diameter and the total headrace tunnel length is approximately 40 km. The crushed rock is transported on conveyor belts to disposal areas near each Adit. The estimated average excavation rate is approximately 25 meters per day per machine. Electricity will begin to flow in April 2007, and the project is scheduled for completion in 2009. This paper is divided into four sections. In the PROJECT OVERVIEW section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drives is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes in the TBM OPERATION section with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 2005

By P Mitchell, J Proffett, I Munajat

Batu Hijau is an island arc porphyry copper-gold deposit located in the southwest corner of Sumbawa Island in the Sunda-Banda archipelago of Indonesia. Southwest Sumbawa Island is underlain by Early Tertiary, low-K calc-alkaline to weakly alkaline volcanic and intrusive rocks. Within the mine area the oldest exposed rocks are medium- to thick-bedded, medium to coarse andesite volcanic lithic breccia, thin bedded, fine-grained volcaniclastic sandstones and mudstones and hypabyssal porphyritic andesite. In the eastern portion of the mine area there is a thick sequence of quartz diorite that postdates the andesites. A small stock of Equigranualar Quartz Diorite predates the Batu Hijau deposit and occupies the contact between the andesitic volcaniclastic sequence of rocks and the Porphyritic Quartz Diorite. Batu Hijau is a world-class copper-gold deposit that has a drill indicated mineable reserve of 914 million metric tonnes grading 0.525 per cent copper (10.58 billion pounds copper) and 0.403 g/t gold (11.8 million ounces gold). Mineralised material not in reserve accounts for an additional 580 million metric tonnes at 0.328 per cent Cu (4.19 billion pounds copper) and 0.171 g Au/T (3.19 million ounces gold), and including an oxide copper resource of 57 million tonnes at 0.37 per cent Cu and 0.12 g Au/T. Copper and gold mineralisation is directly related to quartz veining and wall rock alteration that developed with multiple tonalite porphyry intrusions. The tonalites were emplaced along the contact between the andesitic volcaniclastic rocks and quartz diorite intrusives. Copper and gold are zoned around the porphyry intrusions, which are designated by their contact-age relationships and other features as Old Tonalite, Intermediate Tonalite(s), and Young Tonalite(s). The Old Tonalite was the first copper-bearing intrusion, and although it is the smallest intrusion it has the highest quartz vein density, the strongest alteration and the highest grade. At least two tonalite porphyry intrusions followed the emplacement of the Old Tonalite. Each of these intrusions was associated with less quartz veining, weaker hydrothermal alteration and lower grade copper and gold than the previous intrusion. The intrusive cycle culminated with the emplacement of the Young Tonalite, which contains relatively few quartz veins, is weakly altered and mineralised. Hypogene hydrothermal alteration and sulphide mineralisation developed in five temporally and spatially overlapping stages. These stages consist of Early, Transitional, Late, Very Late, and I Zeolite alteration. Early alteration and sulphide mineralisation accompanied each tonalite porphyry intrusion, but with diminished intensity in each subsequent intrusion. Transitional and later stages of alteration and mineralisation postdate the tonalite porphyries and overprint Early stage alteration and mineralisation. Early alteration and mineralisation consisted of biotisation, secondary magnetite and plagioclase development, fine porphyry-style stockwork veining and ore mineralisation. Magnetite-biotite????quartz stringers and dark micaceous (biotite-sericite) veinlets were developed. The veinlets were accompanied by biotisation of magmatic mafic minerals and groundmass. Thin, irregular and discontinuous æAÆ type quartz veinlets and fine-grained chalcocite, digenite and bornite mineralisation accompanies the Early alteration. It is hypothesized that most of the copper mineralisation was originally deposited as bornite, digenite and chalcocite. Secondary plagioclase was added along the selvages of the early quartz veinlets. Early alteration is pervasive within and proximal to the tonalite porphyries. In the distal portions of the deposit, andalusite and anthophyllite formed at intermediate to shallow depths, and in the deeper portions of the deposit, respectively. The andalusite and anthophyllite probably developed at the same time as the early magnetite-biotite-quartz alteration in the core of the deposit. Transitional-age alteration consists of oligioclase/albite-sericite-chlorite- quartz-¦vermiculite and is associated with æBÆ quartz veins. Through-going planar æBÆ veins are thicker than æAÆ and æA-familyÆ veinlets and have chalcopyrite????bornite along vuggy centrelines and narrow oligioclase????albite alteration envelopes. Rare æCÆ chalcopyite¦quartz veinlets were also formed during Transitional alteration. During Transitional alteration early copper sulphide minerals (chalcocite, digenite and bornite) are converted to bornite and chalcopyrite. The majority of the copper (50 - 70 per cent) in the deposit is contained in ores in which chalcopyrite is the predominant sulphide. Late alteration consists of feldspar destruction and replacement by sericite and other minerals. The late alteration is accompanied by the development of æDÆ sulphide veinlets and veins. These veins consist of pyrite and quartz????chalcopyrite. Within the halos of the late pyritic veinlets biotite is replaced by sericite, quartz-sericite, quartz-andalusite, or quartz-pyrophyllite+kaolinite replace plagioclase, and magnetite is converted to specularite and/or pyrite. In the periphery of the deposit, the feldspar destructive alteration, together with outer zones of Transitional-age alteration, constitutes what is commonly referred to as a æpropylitic zoneÆ. Very Late hydrothermal alteration is also characterised by feldspar destruction, but differs from Late alteration in that feldspar is replaced by smectite in association with sericite and chlorite. Sulphide mineralisation in this stage consists of sphalerite, galena, tennantite, pyrite and chalcopyrite. The last stage or I Zeolite alteration consists of low-temperature, open space filling consisting of stilbite or laumontite¦calcite. Supergene oxidisation of the orebody extends to a maximum depth of 210m. Isolated deep oxidation occurs along open fracture zones to depths of ~400 metres along æDÆ vein filled fracture zones. Weak supergene copper enrichment occurs in a thin horizon (15 to 60 m thick) that blankets the top of the deposit. The main supergene copper mineral is secondary æsootyÆ chalcocite replacement of sulphide grains and as veins.

Jan 1, 1999

By Dan A. Brown

The New Mississippi River Bridge (MRB) employed conventional design-bid-build procurement, but the bidding process included the opportunity for pre-qualified bidders to develop and propose confidential Alternative Technical Concepts (ATC?s) for evaluation and approval in advance of bidding. The ATC process provides a mechanism for value-engineering prior to bid, with incentives and opportunities for both the owner and the bidding contractor. The contract described in this paper is for the river bridge composed of a cable-stayed crossing with two pylons and the anchor piers on each side of the river. The Massman-Traylor-Alberici (MTA) team developed a re-designed foundation system for the main pylon and anchor foundations which utilizes their equipment and experience along with field load test measurements to optimize the foundations. The paper describes the experience with the use of the pre-bid ATC process on the project from the perspective of the bidder, and outlines some of the benefits and limitations of this concept with respect to foundation design and construction. Some keys for success are identified and impediments to the effective implementation of the process are described.

Jan 1, 2011

By Emmanuel Henry

Few industries are more challenged by technical, political and market uncertainty than the mineral industry. Technical uncertainty in mining projects concerns the volume and quality of the resource, the processing and metallurgical parameters, the production efficiency, etc. Political uncertainty can take diverse forms and includes possibilities of change in the taxation system, risk of expropriation and risk of social instability or war. Market uncertainty depends on the market structure of the commodity; price and demand volatilities are the most common sources of market uncertainty. Intensive feasibility studies including these uncertainties and risks are required before investing up to billions of dollars in the development of a new mine. Current feasibility studies are often based on a single (or very few) mean geological scenario and simplified price profiles along the life of the project. Yet, strategic decisions, for example, the level of investment in exploration and metallurgical studies, adoption of a flexible, but more costly, mine design and risk-sharing strategies are made at an early stage. Over the last twenty years, Real Option theory has emerged as a unifying framework enabling strategic planning under uncertainty (technical, political and market). Geological and market variances (second order statistics) are pivotal for proper uncertainty quantification. The present study explores the possible benefits of combining modern geostatistical tools and financial techniques for project management. More precisely, the following questions are examined: Is geological uncertainty really an issue? Can we combine geological and price uncertainties in a unifying Real Option framework? A simple example aimed at illustrating the concepts involved is presented.

May 1, 2003

By Morris T. Worley

Editor’s note: Mining companies doing business in Central Asia, and parts of the developing world, should look for ways to promote community development through the introduction of appropriate technology. This article should be of interest to SME members. It shows sustainable development type projects need not be massive or expensive. Smaller, utilitarian projects are equally valuable to developing communities as they seek to develop their own economic and social infrastructures. Joint Development Associates International (JDA) began humanitarian relief and community development in Central Asia in 1992, following the collapse of the former Soviet Union. Appropriate technology has played an important role in the company’s efforts to assist those segments of society that are most vulnerable to poverty and disease.

Jan 1, 2005

By J. Geertsma, F. de Klerk

During the hydraulic fracturing treatment of an oil or gas well the liquid pressure in the borehole is increased until tensile stress in the surrounding rock exceeds tensile strength. Once a tensile fracture is initiated, it is penetrated by liquid from the borehole and fracture propagation under continuous hydraulic action takes place. The fracturing liquid carries a propping agent to ensure a highly permeable flow channel after pressure release. Field results range from failure to obtain increased production to outstanding success. In all cases, however, it unfortunately remains uncertain whether the values chosen for the operational parameters, such as injection rate, pumping time and fluid viscosity, were in fact the ideal ones. Though experience provides a lead, a more satisfactory way to predict results would seem to be to subject the fracture propagation process to a theoretical analysis that (1) makes the maximum use of the relevant physical information and (2) so simplifies the resulting calculations that the field engineer gets practical data that he can handle comfortably. We are attempting here to do this in connection with the prediction of fracture width and areal extent before pressure release. What remains of the fracture afterwards depends on the distribution of the propping agent between the fracture walls, and that is a separate story. Idealization of the Problem To keep the problem tractable, a number of simplify- ing assumptions have had to be made: 1. The formation is homogeneous and isotropic as regards those of its properties that influence the fracture-propagation process. 2. The deformations of the formation during fracture propagation can be derived from linear elastic stress-strain relations. 3. The fracturing fluid behaves like a purely viscous liquid; i.e., any peculiar flow behavior due to the addition of gelling agents or other additives is neglected. Moreover, the effect of the propping agent distribution on the distribution of fluid viscosity in the fracture is not taken into account. 4. Fluid flow in the fracture is everywhere laminar. 5. Simple geometric fracture-extension patterns are assumed — either radially symmetrical propagation from a point source (Fig. 1A) or rectilinear propagation originating from a line source (Fig. 1B). In the first case the periphery of the fracture is circular, in the second case it is rectangular. 6. A rectilinear propagation mode can be accomplished only by injection over a large perforated interval, thus forming a line source. Such a rectilinear fracture must therefore be located in the vertical plane. A circular propagation mode might be expected from injection through a narrow band of perforations. This forms a point source. Because gravity effects are excluded from our considerations, the fracture propagation plane may in this case assume any angle with respect to the wellbore as far as the

Jan 1, 1970

By Rudolf E. Greuer

It is undisputed that an interaction between mine fires and mine ventilation systems exists. The ventilation carries the poisonous and sometimes explosive combustion products, which constitute the greatest danger of mine fires, through the mine and it provides the oxygen on which the intensity of the fire depends. The fire, on the other hand, can produce considerable ventilation disturbances which make it difficult to predict the path along which the combustion products travel. The opinions, how serious a threat such fire generated ventilation disturbances are, vary. Where shallow deposits are mined and brisk ventilation currents are used, it is frequently felt that these disturbances are of no serious concern. Where mine workings extend over larger elevation differences and where such disturbances have been encountered and been the cause of some larger disasters, their assessment is an integral part of all fire emergency plans. The author felt that the potential of digital computers for the design of ventilation emergency plans, contrary to their acceptance for conventional ventilation planning for more than two decades, is not yet fully utilized. He designed a program for the simulation of ventilation systems under emergency conditions in particular fires. This was part of work completed for a contract with the U.S. Bureau of Mines ( Open File Report OFR 115(1)-78)

Jan 1, 1980

By Bruce Gellar

In March, the Prospectors and Developers Association of Canada (PDAC) held its annual conference in Toronto, Ontario. This is the third PDAC meeting the author has attended. The following are some impressions of the meeting. And the author looks forward to the joint meeting of the PDAC and the Canadian Institute of Mining, Metallurgy and Petroleum to be held March 5-10, 2000, entitled Mining Millennium 2000. One of the features of next year’s gathering is a proposed forum of world mining ministers, the first ever to be held anywhere.

Jan 1, 1999

Digital Simulation of Particulate Processes The inherent complexity of mineral particulates (shape, size and mineralogical texture) has challenged conventional simulation model approaches for decades. Much effort was expedited in using mathematical assumptions to accommodate stereological effect. With the advance of instrumental methods such as x-ray microtomography 3D structure can, in many cases, be measured directly. The information derived from such measurements provides direct input to building the structural digital model. In addition digital simulation methods that enable creation of process realistic particulate properties in an efficient digital computer space have demonstrated their effectiveness to model a variety of realistic packing, sorting and multi-phase processes. The paper reviews recent advances in the use of information derived from 3D micro-tomographic imaging and laser scanning technology can be coupled with digital methods to enable simulation of tablet compaction and dissolution, filtration and permeability, column packing and leaching kinetics, packing and cementation of nuclear waste. By assigning 'properties' to a digital zone (voxel) in the computational space it is possible to mimic the realistic characteristics of quite complex particulate mineral processing systems. The system self-adapts to correct the coherent particle characteristics (shape, size, compound, porosity) with time. Such simulations are useful to elucidate the sensitivity of system performance to variations in process parameters. Dimensional scaling of the approach is also possible, as the case studies will illustrate, in deploying the method to both small (micron) and large (m) features. The use of process realistic simulations presents experimental challenges in code validation. It is in this context that other tomographic methods play a role in direct 3D measurement of system behaviour such as electrical and optical sensors.

Sep 13, 2010