Search Documents

By B. W. Dyer

IN 1924, the Crescent Eagle Oil Co., while drilling the salt section of the Paradox formation in Grand County, Utah, encountered a salt that did not appear to be sodium chloride. This salt was analyzed and showed the presence of potash minerals, both sylvite (KC1) and carnallite (KMgC12.6H20). Because of the high potash content of the sample, there was considerable speculation: (I) as to whether the hole had been salted, and (2), if not, the extent, richness, and the depth at which the deposit occurred. The discovery caused a large amount of activity in the area. During the next few years, 68 potash prospecting permits were issued by the Government, 24 under the Act of 1917 and 44 under the Act of Feb. 7, 1927, each including about four sections of land. Several holes, all shallow, were drilled for potash. A number of holes were drilled for oil into the salt horizon and the cuttings collected at the oil wells were examined petrographically and chemically. The shallow test holes were not sufficiently deep to reach the potash horizon and revealed nothing of value, but several of the oil test holes gave some indication of where potash might be found. LOCATION AND GEOLOGY OF DEPOSITS The potassium and magnesium salts have been found in various places from the Denver and Rio Grande Western Railroad tracks about seven miles west of Thompsons, in eastern Utah, to Cane Creek, a tributary of the Colorado Rivera distance north and south of about 35 miles. In this locality, there appear to be five separate deposits: the Crescent Eagle area, which is in T. 22 S., R. 19 E.; the Salt Valley area, in the vicinity of the north-south line of T. 23 S., between R. 20 E. and R. 21 E.; the Seven Mile area, in the eastern part of T. 25 S., R. 2o E.; the Cane Creek area, on the Colorado River, in T. 26 S. and T. 27 S., R. 2o E. and R. 21 E.; and the Salt Wash area, in T. 22 S. and T. 23 S., R. 16 E. and R. 17 E. (Fig. I.) The Crescent Eagle and Salt Valley areas are in the Salt Valley anticline, some of the wells being in the fault graben and others outside. Structurally, the Salt Valley anticline is very complex, and can be described in general terms as a northwesterly plunging collapsed anticline about 15 miles long. In the Crescent Eagle area, the valley graben is about 1 mile wide and the salt probably forms a plug, the apex of which is in the vicinity of the Crescent Eagle well. Owing to the complex structure, there has been every opportunity for flowage in the salt to cause local thinning or thickening of beds. The regular succession of formations in the general area* is: [Cretaceous Mancos Dakota Jurassic Morrison Summerville Entrada Carmel]

Jan 1, 1945

By G. S. Hume

Production of petroleum and natural .gas increased in Canada in 1940 over the previous year. Alberta produced more than 97 per cent of the total Canadian production of 8,718,053 bbl. of oil, an increase for this province of nearly 12 per cent, whereas in Ontario and New Brunswick, where the production is relatively small, there was a slight decline. In Alberta the main producing field is Turner Valley, on the eastern edge of the foothills southwest of Calgary, and development continued in this field in 1940 with the completion of 36 wells, all of which obtained production. In the Red Coulce field, close to the International Boundary, near Coutts, no new wells were drilled and the seven producing wells showed a decline of 900 bbl. below the previous year. Also, in the Wainwright field of east central Alberta, four wells, yielding heavy crude oil, produced 4000 bbl. less oil than in 1939, owing possibly rather to discontinuous operation than to actual decline in potential yield. This decline was more than offset by production from a new field 40 miles northeast of Wainwright, at Borradaile, producing oil of 14" to I 5° A.P.1. There was a small increase in production during 1940 from the Del Bonita field, in southern Alberta, where the production is from two wells. The outstanding development of the year was the completion of Standard Oil Princess No. 2 well in the Steveville area, on the Plains 100 miles east of Calgary. This well was completed late in December with an initial flow1 of 520 bbl. of 26.3" A.P,I. oil, and 12,750 M cu. ft. of gas from the upper part of the Mississippian limestone. It has opened up a new field and given a further proof of the potentialities of the Southern Plains. The production of petroleum in Canada is shown in Table I. Since most of the yield comes from Alberta, the production is shown from the various fields in Table 2. The sale value of the petroleum produced in Canada in 1940 exceeded 11.1 million dollars, which is still somewhat less than the value of the natural gas production, shown in Table 3. Table i.—Production of Petroleum in Canada" Barrels Province 1939 1940 New Brunswick........ 20,101 21,161 Ontario............... 206,196 186,471 Alberta............... 7,595,000 8,493,237 Northwest Territories. . 17,013 8,493,23717.184 Total............... 7,838,310 8,718,053 Value............... $10,353,351 $11.113,000 0 Bureau of Statistics, Ottawa. Turner Valley, Alberta Turner Valley continues to be by far the largest producing field in Canada (details are given in Table 4), The limits of the Pr in- field are now Known. On the east the oil area is bounded by the gas cap, which in turn is cut off on its east side by a major overthrust fault; on the west, ii is defined by edge water at a level of 4roc

Jan 1, 1941

By Z. D. Hora, W. N. Hamilton

Introduction Some unique opportunities exist for industrial minerals in British Columbia and Alberta. The region's diversified geology, particularly in British Columbia, offers favorable environments for a rich variety of mineral resources. Many minerals have been produced for years. For some, however, the level of production is far less than the potential. Others have had production in the past, but are not currently produced. Still others are known to exist and may have been actively prospected. But they are not yet developed. In addition, a number of speculative possibilities have recently come to light. The potential significance is not fully confirmed, but is suggested in showings in favorable geologic settings. Location and geography British Columbia and Alberta are the westernmost provinces in Canada (Fig. 1). The region overlaps two major physiographic divisions of the country, the Cordillera and the Interior Plains. It also takes in a small segment of the Canadian Shield on the east. The entire territory is greater than 1.6 Mkm2 (618,000 sq miles). Most of British Columbia lies within the Cordillera, a mountainous belt some 800 km (500 miles) wide. The belt is made up of three main physiographic components, the Eastern, Interior, and Western subdivisions. The Eastern subdivision embraces the rugged, linear ranges of the Rocky Mountains, elevations between 2600 and 3300 m (8530 and 10,800 ft). They form a 100-km (62-mile) wide band straddling the BC-Alberta border and extending northwest across northern British Columbia. The Interior subdivision includes several ancient mountain ranges but is dominated by an intermountane plateau area of low relief (average elevation 1200 m or 3900 ft). The Western subdivision is dominated by the Coast Mountains (elevations between 1800 and 4000 m or 5900 and 13,123 ft). These form a band about 175 km (110 miles) wide into which are sculptured the spectacular fiords of the BC coastline. Alberta lies largely within the Interior Plains, a prairie region of low to moderate relief (elevations between 200 and 1200 m or 650 and 3940 ft) formed of nearly horizontal bedrock strata. The Plains surface rises gradually to the southwest toward the deformed belt of the Rocky Mountains, where the bedrock strata are upturned, folded, and faulted. To the east, the Plains merge with the Canadian Shield, which exposes the Precambrian crystalline basement of western Canada. The total population of the BC-Alberta region is about five million people. Minerals, forestry, and agriculture are the primary industries here. It has well developed infrastructures to service these industries. British Columbia is third among the Canadian provinces in metal mining - $1.1 billion in 1985 - and first in forest products. It is also second in hydro-electric power development. Alberta leads all provinces in total mineral production, largely due to its extensively developed petroleum and natural gas resources - $26.2 billion in 1985.

Jan 12, 1987

By Christine M. Kammer

In 1852, six barrels of iron ore were loaded aboard the steamer Baltimore at Marquette, MI, after a trip by mule wagon from the nearby Cleveland Iron Mining Co. Shipped to Sault Ste. Marie, they were portaged around rapids and reloaded onto another ship for the final journey to the steel mills of Cleveland. In 1855, the same company-the predecessor of Cleveland-Cliffs Iron Co.-chartered the brigantine Columbia to carry the first iron-ore cargo through the newly opened Soo locks. In 1981, about 2,190 iron-ore shipments in the form of taconite pellets were transported by water from US Great Lakes-ports. The total volume during the 284-day shipping season was 63 Mt (62 million It). Counting Canadian ship¬ments, almost 76 Mt (75 million It) of iron ore were moved on the lakes last year. The five Great Lakes-Superior, Huron, Michigan, Erie, and Ontario-contain 20% of the world's fresh water. The area surrounding the lakes has 26% of the nation's populations, 47% of its steel production, and over 80% of the raw materials required to make steel. That figure includes 71% of the country's iron ore and 40% of its limestone. Only the availability of low-cost water transportation of raw materials has kept the heartland steel producers competitive. Iron ore shipped on the lakes originates in the Lake Superior district's Mesabi and Marquette iron ranges. Major mines and their principal partners are Cleveland-Cliffs Iron Co.'s Empire, Republic, and Tilden; Armco and Republic's Reserve Mining Co.; Oglebay Norton Co.'s Eveleth; Hanna Mining Co.'s National and Butler; Inland Steel Co.'s Minorca; Pickands Mather & Co.'s Erie and Hibbing, the latter operated in conjunction with Bethlehem Steel Corp.; and US Steel Corp.'s Minntac. Pelletized ore products at these facilities is shipped through seven principal ports on the upper lakes: Duluth, Two Harbors, Silver Bay, and Taconite Harbor, MN; Superior, WI, and Marquette, MI, on Lake Superior; and Escanaba, MI, on Lake Michigan. In 1981, tonnage volumes ranged from 13.3 Mt (13.1 million It) shipped from Duluth, to Marquette's total of 5.4 Mt (5.3 million It). The ore docks, with two exceptions, are operated by railroads, most of which are owned by mining companies. Table 1 illustrates US iron-ore shipments in 1981. In the lower lakes, ore is discharged at dock facilities close to the great steel-producing centers of Chicago, Detroit, Cleveland, Pittsburgh, and Buffalo. Between the mines and mills, lakes and connecting waterways form one of the country's most effective transportation systems. Each year, vessels on the Great Lakes transport about 181 Mt (200 million st) of bulk industrial and agricultural materials-a greater quantity at a lower cost than can be achieved by any other transportation mode. Major commodities in Great Lakes trade are iron ore, coal, grain, limestone, cement, sand, and petroleum products. About 125 US flag vessels serve this trade, among them 13 "1,000-

Jan 10, 1982

By F. S. White, E. L. Kinsella

THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to ' quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,1 showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.2 Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a 1/4-in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontally at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 1/2 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4 1/2-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1952

By D. V. Carter, D. C. Williams

Four oil discoveries were made in east and east central Texas during 1940, three of which represented new fields. In the Chapel Hill field, Smith County, oil was found where formerly only gas and distillate were produced. The three oil fields discovered are: Hawkins, Wood County; Pittsburg, Camp County; and Tehuacana, Limestone County. Important extensions were made to the following fields: Bazette, Navarro County; Long Lake, Anderson and Leon Counties; Cayuga, Anderson, Freestone and Henderson Counties; Opelika, Henderson County; and Talco, Titus and Franklin Counties. At the close of the year 54 oil and gas fields were producing in the district. There were 13 other fields, 11 oil and 2 gas, which have been abandoned. The East Texas field led the district in the number of completions for the year. During the year about 622 wells (oil and distillate wells included) were completed and 80 wildcats were drilled. Production and Proration During the year 170,424,685 bbl. of oil (distillate production included) were produced in the district—a decrease of 2.6 per cent from the 175,053,729 bbl. (distillate production included) during the preceding year. The district's production for the year 1938 was 182,369,484 bhl. As usual, most of the district's annual production was in the East Texas field, which produced 139,095,694 bbl. (distillate production in- cluded) during 1940, or 81.6 per cent of the total oil produced as compared with 141,333,317 bbl. (80.7 per cent) for 1939. The December estimated daily average production in the district was 424,565 bbl. The district accounted for 34.9 per cent of the state's annual production, compared to 36.7 pcr cent of the state's 1939 production. The decrease in production for 1940 may be attributed to changes made in proration schedules. Any material changes in the district's annual production may be considered for the most part as a reflection of proration-schedule changes affecting the East Texas field, since it is by far the most important field in the area. The entire state was subject to 71 shutdown days for the year; the East Texas field to 131; and the Rodessa field (Cass County, Texas, portion) to 5 days. No important changes were made in field rules and regulations during the year regarding the allocation of oil in individual fields in this district. Discoveries The Hawkins field is in southeastern Wood County in and principally north of the town of Hawkins. Development to date indicates that the field is somewhat of an elongated anticline trending slightly east of north and the proved oil area appears at this time to cover approximately 4000 acres. The oil production has been secured from the Woodbine sand, Upper Cretaceous; a considerable quantity of gas has been encountered in the Sub-Clarksville formation (Eagleford shale) in the higher part of the structure. It appears that a free gas

Jan 1, 1941

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By J. P. Smith

DURING the winter of 1946 to 1947 potash operations in Germany, France and Spain were visited by the author. The U. S. Department of Commerce, through its Field Intelligence Agency Technical, sponsored the inspection of German properties by representatives of the American Potash Industry. Vast deposits of potash salts occur in the above-mentioned countries, and the production and marketing of these salts are important in their respective economies. Germany An area of some ten thousand square miles of north central Germany is underlain by lenses of potash salts interbedded with greater thicknesses of sodium chloride or common salt. These salt measures are relict deposits from the evaporation of an arm of the Zechstein (Permian) Sea which formerly covered northern Europe. During the peak year of 1940, Germany produced salts containing 1,860,000 tons of K,O and, next to coal, potash is its most important mineral raw material. The German deposits are found in the synclinal areas flanking the Flechtingen, Hartz Mountain and Thuringian uplifts, and, to the north they lie beneath the plains of Hannover. The regional dip of the salt measures is to the north, hence, lenses of potash found at depths of 500 to 1000 m* in the Two general depositional provinces of potash concentrations are recognized: (1) the main basin, and (2) the subsidiary basin. The main basin embraces the producing districts of Stassfurt, Sud Hartz, Halle, and Hannover-Braunschweig. From J. P. SMITH, Member AIME, is Clzief Geologist, U. S. Potash Co., Carlsbad, New Mexico. New York Meeting, February 1948. TP 2621 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 26, 1948. 40 to 45 pct of the German production comes from this basin. The Werra-Fulda district, producer of 50 pct or more of the German potash, lies in the subsidiary basin. Salt Stratigraphy: Five commercial potash zones or beds are recognized. The three beds present in the main basin are: The Stassfurt bed that occurs near the top of the older salt, and the Ronnenberg and Riedel beds in the younger salt occurring 200 to 300 m, respectively, above the Stassfurt bed. The Stassfurt bed is found over the entire main basin, while the Ronnenberg and Riedel are restricted to the Hannover area. Two potash beds occur in the Werra basin. These are the Thuringian, or lower bed and the Hessen or upper potash bed that occurs 60 m above. These beds lie 210 and 150 m, respectively, below the position of the Stassfurt bed, and are restricted to the Werra basin. The upper bed is 2.5 to 11.5 m in thickness, and the principal ores are hartsalz with varying thicknesses of carnallite. The lower bed averages 3 m in thickness, and contains hartsalz. The upper bed is presently being mined, and the

Jan 1, 1951

By C. E. Shoenfelt

Wildcat drilling in the Rocky Mountain region did not suffer as large a decline in 1942 as was anticipated. The drilling program laid out by the Government at the beginning of the year stressed wild-catting operations and called for reduction of drilling in proved fields. The increased wildcatting campaign did not yield a great many new discoveries, nor important extensions to old fields. Several interesting wildcat wells were drilled in Colorado in 1942 but no new fields were discovered. The Wilson Creek field was extended and about 400 acres added to its reserves. In Montana two new oil fields and two small gas fields were discovered. The developments in the marketing situation had improved, however, making the prospects especially bright for 1943, as will be shown presently in the section on Montana in this report. In New Mexico eight wells were completed, which constituted discoveries ol either oil or gas but none of these was of major proportions. In Wyoming one new oil field and one new gas field were discovered, and one old oil field and one old gas field were extended. Most important was the disco-very of prolific oil producers in deeper sands in three old oil fields, of which one at least, Elk Basin, probably is of major proportions. Government Action On Dec. 26, 1942, President Roosevelt signed the O'Mahoney bill, calling for a flat 12.5 per cent royalty on lands in the public domain. It is expected that the enactment of this bill will encourage wildcatting in the public land states. Opportunity for a full discussion of the problems of reserves and production was afforded at the hearings conducted on the O'Mahoney bill by the minerals subcommittee of the Senate Committee on Public Lands and the statements submitted at these hearings last fall placed the situation, its causes and the logical remedy, clearly on record. It was established at the hearings that for several years the volume of oil discovered per wildcat well drilled has steadily declined; new fields discovered have not been of major proportions; drilling costs have advanced rapidly; a sharp decline in exploratory drilling took place in 1942, while the proportion of dry holes increased; the inescapable conclusion is that to find new reserves the search for oil must be intensified and much more wildcat drilling ' must be done. To ensure an adequate drilling campaign, the Petroleum Industry War Council, the Interstate Compact Commission and other representative oil organizations have voiced by resolution their opinion that an upward revision of crude prices is necessary to provide an incentive to the prospector to undertake the hazards of wildcat drilling, since statistics prove that only ope in five or six wells drilled results in actual production. Former Price Administrator Henderson rejected the recommendations for price increases and declared himself unalterably opposed to a general price advance, On the ground that such advances would contribute to inflation. Now that Mr. Hender-

Jan 1, 1943

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

By Paul M. Jr. Musgrove, Thomas D. Henderson, Mark B. Nesbitt

Introduction History. Vat leaching operations began in October 1953. Since that time, about 4.2 million tpy of oxide ore averaging 0.72% copper have been treated. Economic conditions, improved operating methods, and increased production facilities have allowed the ore grade to be reduced over the years. The average ore grade was 0.84% Cu during the 1950s, 0.68% in the 1960s, and was 0.50%, or below, during the 1970s. By 1961 some 35 million tons of oxide ore had been removed from the mine, exposing the underlying sulfide ore body. A 5,000¬ tpd concentrator was constructed and put into operation to treat the sulfide ore in November 1961.1 The original crushing plants were used for both oxide and sulfide ores, but by adding a third crushing shift, six days per week, the total ore treated was raised from 12,000¬17,000 tpd. Dwindling oxide ore reserves prompted expansion of the concen¬trator to 13,500 tpd in 19672 so that exhaustion of known reserves of both ores would occur at nearly the same time. Again, no additional crushing facilities were added during the expansion. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to about 9,000 tpd. Instead, the addition of two crushing shifts per week and improved operating procedures have increased the treatment rate to 26,500 tpd-13,000 tpd to the leaching plant and 13,500 tpd of sulfide ore treated in the concentrator. Geology. The Yerington ore body is a disseminated porphyry copper deposit where a quartz monzonite porphyry intrusive contains the major part of the ore values, with some copper mineralization found in the adjacent granodiorite and other rocks. The geology of the Yerington Mine was aptly described by J. R. Wilson (Mining Congress Journal, June 1963). The ore body is one of few porphyries where geologic conditions were optimum for the formation of an important concentration of oxidized ore with minimum economic effect of secondary enrichment. The principal mineral in the oxidized zone is chrysocolla, which irreg¬ularly occurs dispersed throughout the rock and as narrow seams along fissures. The grade of the ore in the oxidized zone is generally the same as in the primary sulfide below, although some massive concentrations do occur as vein-like fissures and as filling of breccia zones. Cuprite, tenorite, melaconite, malachite, and azurite occur but are not abundant. Lying between the chrysocolla horizon and the primary sulfide is a transition zone whose limits are irregular but seldom with vertical range exceeding 50 ft. Chalcocite, cuprite, melaconite, native copper, and chrysocolla occur superimposed on the primary sulfides. Chalcocite replacement of chalcopyrite, as well as secondary chalcocite, do occur. The primary sulfide minerals are chalcopyrite and pyrite, with minor amounts of bornite and covellite. There are no appreciable gold or silver values, and molybdenite has rarely been noted.

Jan 1, 1985

By J. P. Smith

DURING the winter of 1946 to 1947 potash operations in Germany, France and Spain were visited by the author. The U. S. Department of Commerce, through its Field Intelligence Agency Technical, sponsored the inspection of German properties by representatives of the American Potash Industry. Vast deposits of potash salts occur in the above-mentioned countries, and the production and marketing of these salts are important in their respective economies. Germany An area of some ten thousand square miles of north central Germany is underlain by lenses of potash salts interbedded with greater thicknesses of sodium chloride or common salt. These salt measures are relict deposits from the evaporation of an arm of the Zechstein (Permian) Sea which formerly covered northern Europe. During the peak year of 1940, Germany produced salts containing 1,860,000 tons of K,O and, next to coal, potash is its most important mineral raw material. The German deposits are found in the synclinal areas flanking the Flechtingen, Hartz Mountain and Thuringian uplifts, and, to the north they lie beneath the plains of Hannover. The regional dip of the salt measures is to the north, hence, lenses of potash found at depths of 500 to 1000 m* in the Two general depositional provinces of potash concentrations are recognized: (1) the main basin, and (2) the subsidiary basin. The main basin embraces the producing districts of Stassfurt, Sud Hartz, Halle, and Hannover-Braunschweig. From J. P. SMITH, Member AIME, is Clzief Geologist, U. S. Potash Co., Carlsbad, New Mexico. New York Meeting, February 1948. TP 2621 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 26, 1948. 40 to 45 pct of the German production comes from this basin. The Werra-Fulda district, producer of 50 pct or more of the German potash, lies in the subsidiary basin. Salt Stratigraphy: Five commercial potash zones or beds are recognized. The three beds present in the main basin are: The Stassfurt bed that occurs near the top of the older salt, and the Ronnenberg and Riedel beds in the younger salt occurring 200 to 300 m, respectively, above the Stassfurt bed. The Stassfurt bed is found over the entire main basin, while the Ronnenberg and Riedel are restricted to the Hannover area. Two potash beds occur in the Werra basin. These are the Thuringian, or lower bed and the Hessen or upper potash bed that occurs 60 m above. These beds lie 210 and 150 m, respectively, below the position of the Stassfurt bed, and are restricted to the Werra basin. The upper bed is 2.5 to 11.5 m in thickness, and the principal ores are hartsalz with varying thicknesses of carnallite. The lower bed averages 3 m in thickness, and contains hartsalz. The upper bed is presently being mined, and the

Jan 1, 1951

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By C. E. Shoenfelt

Wildcat drilling in the Rocky Mountain region did not suffer as large a decline in 1942 as was anticipated. The drilling program laid out by the Government at the beginning of the year stressed wild-catting operations and called for reduction of drilling in proved fields. The increased wildcatting campaign did not yield a great many new discoveries, nor important extensions to old fields. Several interesting wildcat wells were drilled in Colorado in 1942 but no new fields were discovered. The Wilson Creek field was extended and about 400 acres added to its reserves. In Montana two new oil fields and two small gas fields were discovered. The developments in the marketing situation had improved, however, making the prospects especially bright for 1943, as will be shown presently in the section on Montana in this report. In New Mexico eight wells were completed, which constituted discoveries ol either oil or gas but none of these was of major proportions. In Wyoming one new oil field and one new gas field were discovered, and one old oil field and one old gas field were extended. Most important was the disco-very of prolific oil producers in deeper sands in three old oil fields, of which one at least, Elk Basin, probably is of major proportions. Government Action On Dec. 26, 1942, President Roosevelt signed the O'Mahoney bill, calling for a flat 12.5 per cent royalty on lands in the public domain. It is expected that the enactment of this bill will encourage wildcatting in the public land states. Opportunity for a full discussion of the problems of reserves and production was afforded at the hearings conducted on the O'Mahoney bill by the minerals subcommittee of the Senate Committee on Public Lands and the statements submitted at these hearings last fall placed the situation, its causes and the logical remedy, clearly on record. It was established at the hearings that for several years the volume of oil discovered per wildcat well drilled has steadily declined; new fields discovered have not been of major proportions; drilling costs have advanced rapidly; a sharp decline in exploratory drilling took place in 1942, while the proportion of dry holes increased; the inescapable conclusion is that to find new reserves the search for oil must be intensified and much more wildcat drilling ' must be done. To ensure an adequate drilling campaign, the Petroleum Industry War Council, the Interstate Compact Commission and other representative oil organizations have voiced by resolution their opinion that an upward revision of crude prices is necessary to provide an incentive to the prospector to undertake the hazards of wildcat drilling, since statistics prove that only ope in five or six wells drilled results in actual production. Former Price Administrator Henderson rejected the recommendations for price increases and declared himself unalterably opposed to a general price advance, On the ground that such advances would contribute to inflation. Now that Mr. Hender-

Jan 1, 1943

By D. C. Williams, D. V. Carter

Four oil discoveries were made in east and east central Texas during 1940, three of which represented new fields. In the Chapel Hill field, Smith County, oil was found where formerly only gas and distillate were produced. The three oil fields discovered are: Hawkins, Wood County; Pittsburg, Camp County; and Tehuacana, Limestone County. Important extensions were made to the following fields: Bazette, Navarro County; Long Lake, Anderson and Leon Counties; Cayuga, Anderson, Freestone and Henderson Counties; Opelika, Henderson County; and Talco, Titus and Franklin Counties. At the close of the year 54 oil and gas fields were producing in the district. There were 13 other fields, 11 oil and 2 gas, which have been abandoned. The East Texas field led the district in the number of completions for the year. During the year about 622 wells (oil and distillate wells included) were completed and 80 wildcats were drilled. Production and Proration During the year 170,424,685 bbl. of oil (distillate production included) were produced in the district—a decrease of 2.6 per cent from the 175,053,729 bbl. (distillate production included) during the preceding year. The district's production for the year 1938 was 182,369,484 bhl. As usual, most of the district's annual production was in the East Texas field, which produced 139,095,694 bbl. (distillate production in- cluded) during 1940, or 81.6 per cent of the total oil produced as compared with 141,333,317 bbl. (80.7 per cent) for 1939. The December estimated daily average production in the district was 424,565 bbl. The district accounted for 34.9 per cent of the state's annual production, compared to 36.7 pcr cent of the state's 1939 production. The decrease in production for 1940 may be attributed to changes made in proration schedules. Any material changes in the district's annual production may be considered for the most part as a reflection of proration-schedule changes affecting the East Texas field, since it is by far the most important field in the area. The entire state was subject to 71 shutdown days for the year; the East Texas field to 131; and the Rodessa field (Cass County, Texas, portion) to 5 days. No important changes were made in field rules and regulations during the year regarding the allocation of oil in individual fields in this district. Discoveries The Hawkins field is in southeastern Wood County in and principally north of the town of Hawkins. Development to date indicates that the field is somewhat of an elongated anticline trending slightly east of north and the proved oil area appears at this time to cover approximately 4000 acres. The oil production has been secured from the Woodbine sand, Upper Cretaceous; a considerable quantity of gas has been encountered in the Sub-Clarksville formation (Eagleford shale) in the higher part of the structure. It appears that a free gas

Jan 1, 1941

By Tanaya Deb, Sujit Kumar Pal

"Experimental investigations are carried out on failure pattern around 2D models of belled anchor piles in dry sand bed of density 15.60 kN/m3 under uplift. The models are having thickness ratio (Ts/Tb) = 0.28, 0.32, 0.38 and 0.46 and total 12 numbers tests are performed on models possessing 45° bell angle and shaft thickness 26 mm. The foundation bed is prepared with alternate dyed and non-dyed sand layers and continued upto reaching embedment ratio of 3, 4 and 5 for each width ratio. The failure points are presented with respect to meridian section of anchor in X-Y coordinate system and the equations formed are of polynomial of degree 3; and R2 values are near about 1. The developed wedge is implemented as three-dimensional axisymmetrical failure surface around similar 3D models. In the horizontal slice method vertical limit equilibrium is used for calculating weight of wedge and mobilized shear (as per Chattopadhyay and Pise, 1986) on the slip surface of each element. The summation of all elementary forces demonstrates gross uplift capacity. The initial and final failure angles are detected and parametric study is conducted on failure pattern as well as predicted net ultimate uplift capacity. Almost all the analytical data are within ± 10% variations with respect to the experimental results of uplift capacity which shows better correlations. INTRODUCTION Belled or enlarged base anchor piles are attractive and economic alternative to the geotechnical engineers for compressive load bearing capacity as well as tension anchorage. These types of anchors may be useful for foundations erected below ground water table. In light weight structures like radar tower, television tower, power pole and outdoor sign pools imbalance horizontal forces due to wind loads, are more than of those self-weight of those structures. Due to chronic tensile loads most possibly from wind loads and associated imbalanced cable tension, the legs of power transmission tower should be properly designed to be safe against resultant pull-out forces. In belled anchor pile, uplift is influenced by embedment ratio, diameter ratio; so, contributions of these parameters on failure surface influence uplift capacity. Balla (1961) first introduced non-linear failure surface in the pattern of circular arc based on Kotter’s equation (1903) and soil friction was assumed to act on slip surface. The predictive mathematical models established by Matsuo (1967), Rao and Kumar (1987), Chattopadhyay and Pise (1986), Saeedy (1987) and Ghaly and Hanna (1994); it was reported that net ultimate uplift capacity was combination of bulk weight of failure wedge and shear resistance along slip surface acting in opposite direction of wedge movement. From the literatures available till date, it reveals that the contribution of mobilised shear and weight of breakout wedge separately, demanding for more clarification depending on the on parameters like embedment ratio, diameter ratio."

Jan 1, 2015

By W. I. Duvall, L. D. Sadwin

Three explosives with different detonation characteristics were tested by studying their cratering ability in a granite-gneiss. The strain wave generating characteristics of these explosives were also studied in the same rock medium. Correlations between the relative performance of three explosives as evaluated by crater studies and other methods of evaluation are indicated. Numerous test methods have been employed to evaluate the output performance of explosives; for example, the underwater explosion method, the airblast method and the ballistic pendulum method.'*' For blasting applications, the study of explosion produced craters and explosion generated strain waves are the most meaningful. This laboratory has employed these techniques extensively for many years and has shown that the detonation properties of explosives and their ability to generate strain waves in rock are related and that the amplitude and shape of the strain wave is related to some of the crater parameters such as slab thickness and fly rock velocity.3'11 However, a good comparison between the relative performance of explosives as determined by the crater and strain wave methods had not been made. The purpose of this investigation was to determine if the relative performance of three explosives as determined by the crater method shows a correlation with the relative performance as determined by the strain wave method. If a good correlation exists between these two sets of relative performance, it should then be possible to relate the detonation properties of an explosive to its ability to break rock in a crater test. In most commercial blasting operations, the diameter of the blast hole remains constant even though the type of explosive may change. In general, it is the explosive volume rather than the weight which remains constant when two or more explosives of different density are compared. Therefore all tests in this investigation were conducted on a constant volume basis rather than on a constant weight basis. TEST SITE AND ROCK PROPERTIES The tests described in this paper were conducted at a granite quarry owned and operated by the Consolidated Quarries Div. of the Georgia Marble Co. at Lithonia, Ga. The tests were performed in an area where the exposed rock surface was nearly horizontal and where the general rock mass had few joints or faults. The rock has an apparent sp gr of 2.6 and a longitudinal propagation velocity of 18,000 fps. The characteristic impedance of Lithonia granite gneiss is 53(lb - sec/in3). EXPERIMENTAL PROCEDURE There are many parameters which must be considered in the study of explosion-produced craters. The role played by each variable in the explosive-rock-crater system can be determined by experimental techniques in which one parameter is varied while others are maintained constant. In this investigation, the crater geometry was studied as the depth was varied for each of three explosives. The explosive volume and rock-type were held constant for all crater tests. The experimental arrangement used in performing the crater tests is illustrated schematically in Fig. 1.

Jan 1, 1965

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

By E. D. Attanasi, M. W. Bultman

Most statistical measures of mineral exploration continued downward in 1986. Prospects in 1987, however, appear to have brightened for exploration as the overall economic health of the mineral industry improved. The Society of Economic Geologists (SEG) survey of US and Canadian firms documents the marked decline in US mineral exploration since the early 1980's. From 1981 through 1986, the total exploration expenditure by US firms declined by more than 73% (Fig. 1). Exploration expenditures by US firms declined by 66%%. US based professional exploration staffs were slashed by 70% (Fig. 2). Also, many firms have written off some reserves because of weak markets or have not delineated new reserves to replace production. The Canadian government reported that between 1981 and 1986 Canadian molybdenum re¬serves had declined by 30%, lead and zinc reserves by 20%, and nickel and copper reserves by 15%. The SEG survey also shows the immediate impact of the decline in the dollar on US exploration expenditures abroad. Between 1981 and 1986 the share of the exploration dollar spent by US firms outside of the country declined by nearly one-half and exploration acreage abroad declined by 69%. The downward trend of the last six years may finally be near the end as a leaner and more efficient minerals industry starts to gear up for a period of increased activity. An industry survey reported to Mine Development Bimonthly (Metals Economics Group) indicates that mining firms were expected to increase exploration expenditures in 1987 by at least 10% above 1986 levels. Worldwide expenditures for 1987 by companies covered by the report were expected to top $800 million. It is the first time since 1984 that an increase in exploration expenditures was expected. Also, the US Bureau of Land Management reported a 30% increase in new mining claims for fiscal year 1987 over fiscal year 1986. The bulk of the increase in claims was in states having intense gold exploration, particularly Washington and Oregon. Much of the optimism is undoubtedly due to the increases in metal prices that occurred in 1987. Some of these increases include gold, average price up about 20%; copper, average price up 24%; aluminum, average price up 26%; and nickel, average spot price up 20%. The SEG survey shows precious and base metals accounting for 89% of the exploration expenditures in the US in 1986, up 52% from 1981. The US Bureau of Mines estimates that 80% of US exploration activity in 1986 was directed entirely at gold (1986 Minerals Yearbook). Worldwide exploration plans indicate the continued dominance of gold exploration. New programs were announced for Ghana, Malaysia, and Indonesia. Major new exploration programs were also launched for lead-zinc sulfides in Morocco, platinum and palladium in northwest Brazil, rare earth minerals in Greenland, diamonds in Indonesia, and heavy minerals off-shore Australia. Significant gold discoveries were made at Angels Camp in Oregon; South Africa, near Potchestroom; India, in the Chitradgra district; Northern Ireland near Mt. Speerin; Chile, San Cris-

Jan 5, 1988

By Harold Vance

The Lafitte field, the largest oil reserve in South Louisiana, is in Jefferson Parish, some 25 miles due south of the City of New Orleans. The discovery well, The Texas Company's No. I, Louisiana Land and Exploration Co., in the southeast corner of sec. 19, T. 17 S., R. 24 E., was completed on May 15, 1935. The initial production of this well was 960 bbl. of 34.9º A.P.I, gravity oil per day, through 1/4-in. choke, with a tubing pressure of 1600 lb. per sq. in. Producing depth was 9558 to 9572 ft., the total depth being 9572 feet. The development of the field has been at the rate of three to eight new producing wells per year. Up to Jan. I, 1944, 60 producing wells and three dry holes had been drilled, while two of the original producing wells had been abandoned, Although the field is not unitized, The Texas Company was the sole operator in the field until the Lafitte Oil Co. completed its NO. I Jefferson Parish, near the center of the west line of the NW/4 sec. 20, T. I7 S., R. 24 E., on July 27, 1941. No additional wells have been drilled by the Lafitte Oil Company. Drilling and WeLl-completion Practices All drilling operations have been conducted with the steam-driven rotary equipment mounted on submersible barges. A canal is dug to the well location and the drilling unit is floated into position. The seacocks are then opened and the barge settles to the bottom. After the well is completed, seacocks are closed and water is pumped out of the barge. This procedure permits the barge, with drilling equipment still in place, to be floated and moved off the location. The conventional open-hole and the gun-perforation method of completing wells has been used in this field. Where possible, the initial completion is from the deepest 'sand and recompletions are made progressively up the hole, by plugging back with cement to the upper sand and gun-perforating opposite the new sand. The oil string usually is 7 5/8 in., 26 to 34-lb. casing. Three wells have been completed using 9 5/8-in. 44-lb casing set below 10.000 feet. Fig. I shows the completion and recom-pletion practices on one well in the field. This figure also shows the relative locations of the different producing sands as shown on the electric well log. Structure The structure is an elongated dome, cut by two north-south faults, which divides the field into three segments. The west segment is the highest structurally and contains most of the recoverable oil and gas. The center segment is less important and the east segment is of little value. Figs. 2, 4, 6, 8 and 10 are depth contour maps on top of the five main producing sands in the field. These maps show the relative size of the five reservoirs and the

Jan 1, 1945