Search Documents

By J. Philip Neal

Feldspar is no example of special mineralization in isolated spots: it can usually be found within a mile or so of almost anywhere. Along with silica sand, it is a major part of our world's total mineral composition. This fact imparts to it an economic status different from a sulfide ore, or potash, or phosphate. While every feldspathic "stringer" does not possess economic potential, the generous distribution does yield a high statistical frequency of good feldspar ore bodies: the adjective "good" being subject to some flexibility of interpretation. The strong chemical bonds of this alkali aluminum silicate give it certain use advantages, but under present technology its individual elements cannot practically be separated to create aluminum, potassium, sodium, silicon - or their oxides. Its present uses rely upon chemical inertness - as in fillers; and on its physical melting characteristics and their effect in glass, enamel, or ceramics.

Jan 1, 1973

By Rafael C. Castro, John Overton, Gregg Sherry, David A. Sutter

This paper presents an innovative ground support solution developed to construct a tunnel cross-passage for the MUNI Metro Turnback (MMT) Project. A “soft center” jet grouting approach was designed to provide solid ground support while maintaining a soft center to allow for hand-mining of a 2.44 m (8 ft.) wide, 3.66 m (12 ft.) tall and 4.6 m (15 ft.) long cross-passage through soft Bay Mud. Prohibitive costs and schedule impacts associated with mining under compressed air (at the time being used for main tunnel construction) were the catalysts to search for alternative methods for cross-passage construction. Limited surface disruption, relatively low costs, ease of subsequent excavation, nominal schedule impacts and proven local success of jet grouting were key factors in selecting and designing this method of ground support.

Jan 1, 1997

By R. A. Egen

The purpose of this book is to provide an indication of what good hoisting practice is and how it might be achieved. To this end the book contains discussions of equipment and inspection and maintenance procedures developed and used by mining people in striving for safe, reliable hoisting equipment. Most of this information comes from domestic practice; the rest is foreign, notably from Canada. Most things discussed have long proved their general worth, and others promise to; a few are beginnings. However, nothing is conjectural or theoretical; the practices described herein are in use somewhere in the mining world. The stress is on equipment in use; it is not a design-guidelines manual. Nevertheless, there are some sections dealing with design material since it may be of value in a maintenance/ replacement sense. Mine hoisting installations encompass such a wide variety of equipment and conditions that it is impractical to specifically cover them all. This book mainly treats conventional systems using conventional components with some discussion of the more common unconventional (special) systems in use. There is no recognized definition for a "conventional" mine-hoisting system. Herein the term means those systems most commonly used in daily operations for transporting men, materials, and product-electrically driven drum and friction hoists, with guided conveyances running in vertical or inclined shafts. Beyond this, what "conventional" means is probably best illustrated by the topics discussed.

Jan 1, 1975

By L. E. Cardwell

This publication contains routine analyses and related source data for 377 natural gas samples from 19 States and two foreign countries. Of this total, 373 samples were collected during calendar year 1970. The remaining four samples were collected during previous years, but releases granting per-mission to publish the analyses were not received until 1970. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Twelve previous publications have presented the results of 9,050 gas analyses prior to 1970. The first three, Bulletins 486,6 576,8 and 617,7 contain analyses and related source data on 5,218 gas samples collected from

Jan 1, 1971

By Herbert Haas

The Bureau of Mines is endeavoring to reduce waste and increase efficiency in the production, refining, and utilization of petroleum . During the last few years the demand for petroleum and its products has increased so much more rapidly than the production that greater efficiency in utilization is now a matter of most serious importance . The Diesel engine, a comparatively new type of internal-combus- ' tion engine, is an important device for insuring more efficient utilization of petroleum and coal-tar products, for it consumes heavy liquid fuels such as can not be utilized in other types. Like the gas or the gasoline engine, it is revolutionary within its province. For some uses this engine is replacing gas and gasoline engines , but its most important duty will be to replace the wasteful consumption of fuel oil in steam engines. Not only will a wider use of the Diesel engine relieve the demand, but it will result in more power being obtained from the same consumption of fuel oils . In spite of these advantages, comparatively few Diesel engines are in use in the United States . In this report the author discusses recent developments in the design and construction of the Diesel engine, the fuels suitable for burning in it, and the uses to which it is particularly adapted .

Jan 1, 1918

By J. T. Chen, S. Winkler, M. J. Worswick, O. Orlov

This paper presents a review of research conducted at the University of Waterloo concerned with the application of aluminum alloy sheet and tube in automotive structures and body panels. The research has focussed on formability prediction and results using a range of damage-based formulations. These models include continuum-level damage approaches and, more recently, a so-called percolation damage approach intended to capture microstructural heterogeneity effects on damage development. This paper presents applications of these damage approaches to simulate formability of experiments considering stretch flange panels. The experiments consider drawbead effects associated with the bend/unbend deformation as the material flows through the drawbead. Recent work on simulating in situ X-ray tomography experiments that capture damage evolution during tensile deformation will also be reviewed.

Jan 1, 2006

By C. L. Van Dover

Organisms living at hydrothermal vents are adapted to catastrophic disturbances in their environment caused by processes such as tectonic activity and mineralization that shift the locus of fluid flux and volcanic eruptions that pave over active systems and reset the hydrothermal cycle. The scientific community appreciates this risk of natural, local loss of species, genetic, and habitat diversity. The risks of more profound loss of diversity and ecosystem function and health as a consequence of additive commercial activities in hydrothermal systems are unknown, and are not the same across all deep-sea hydrothermal systems. Vent communities differ from one ocean basin to another, as do the geological settings and geochemical dynamics of vent systems. Communities on the East Pacific Rise represent one end-member in the catalog of hydrothermal vent communities. In these systems, the life cycle of a hydrothermal field is on approximately the same time scale as the lifespan of the species that live there. From studies of the 1991 and subsequent eruptions at 9N on the East Pacific Rise, we understand the rapidity with which new vents are colonized when nearby brood stocks are available to repopulate the system. Almost instantaneously, microbial biofilms and mats form, followed quickly by invasion of mobile opportunistic organisms (especially crabs, copepods). In a matter of a few months, a predictable succession of sessile organisms recruits, grows, and reproduces. Within two to three years, the system returns to levels of species diversity that begin to match those of the pre-eruption condition. Vents on the Mid-Atlantic Ridge (MAR) represent a different end-member, with catastrophic disturbance rare relative to the life span of the organisms that make up the bulk of the biomass. We have no experience with an eruptive event or other major transformation of venting activity on the MAR and thus have no knowledge or insight regarding the time it would take for the biological diversity to return to pre-cataclysmic levels.

Jan 1, 2008

By Larry G. Stolarczyk

An underground medium frequency radio communications system has been developed and demonstrated in both coal and metal/non metal mines. The principal advantage of the system are its low cost, ease of installation and the ability to provide radio communications to any vehicle or roving miner in the underground mine. The system provides high quality radio coverage in work areas and along manways with existing "wireplant" conductors. The conductors include AC power cable, telephone cable, metal water and high pressure air pipes, etc. The measured communications range from the base station to mobile transceiver exceeded 12,500 ft without the use of repeaters. A cost/benefit analysis shows that the initial cost of the equipment can be returned 2-6 times in the first year. The mine productivity increases by approx. 13 percent.

By C Moorhead

The classification of Mineral Resource estimates for reporting in accordance with the JORC Code is a statement of the Competent PersonÆs confidence in the estimate and an attempt to convey that confidence to the various users of the resource estimate. In general the classification process is either largely subjective, relying on the Competent PersonÆs experience, or relies on statistical measures derived from the estimation process. These statistical measures may not necessarily relate to the overall confidence in the resource which must also take account of the confidence in the geological inputs to the estimation. Several authors, including Jackson et al (2003) and Dominy, Noppe and Annels (2004), have addressed methods of including consideration of geological data and its reliability into the classification process. Henry and Parker (2005) have discussed a quantitative measure for classification of Measured and Indicated Resources related to mine production parcels. These methods rely on the availability of sufficient information for the application of geostatistics, data evaluation techniques or repeated interpretation of data to provide an indication of confidence. They are suitable for very advanced projects. In 2005, using a modification of the financial audit æcontrol and quality criteriaÆ principles, then widely accepted within Newcrest Mining Limited (Newcrest), the principal author developed a scheme which categorised the classified resources into æcontrolÆ and æqualityÆ (or risk) categories. Control covers all aspects of the data collection, the geological interpretation, the data analysis and the modelling of tonnage and grade; it is also influenced by the documentation of the estimate. The quality criteria are a subjective measure of risk associated with the estimation of the resource and refer to the risk that the tonnage and grade are not realised and the consequences if decisions are made on the basis of these estimates. By evaluating the generally accepted level of risk attributed to these quality ratings by Competent Persons within Newcrest, a graphical representation of the confidence in the resource ounces was prepared for communication of the expected confidence in the resource statement.

Jan 1, 2009

By T. Skinner, M. Sahebkar

"In recent years, the mining industry has been inundated with new technologies and software systems to aid in productivity improvement. Accompanying this increased level of technology and computer systems has been the exponential growth in data sources and sinks for all aspects of a mining operation. This rapid growth in data and technology has evolved through vendor “push” approaches and user “pull” scenarios, the result of which has been that currently, no standards exist defining how data from new technology should be accessed and transferred from surface mining equipment and systems. Consequently, many incremental benefits of the systems have not been realized. This paper will present a discussion of this important issue and introduce a new committee formed to address standards to assist the industry in making effective use of current and future technology. Potential benefits accruing from the development of these standards will be illustrated through the use of a case study at Fording Coal Limited. IntroductionThe mining industry is currently faced with a rapid evolution in the computing-based systems capabilities of mobile production equipment. At the same time, there is a trend toward the introduction of even larger machines, with novel designs or incorporation of new technologies within existing designs. Computing and control technology will be required to operate and acquire knowledge about equipment operation, utilization, and performance. Such knowledge has the potential to lead to enhanced equipment design, more appropriate equipment selection, and optimized equipment performance. The equipment systems will be required to be integrated with mine production monitoring systems, maintenance management software, and a wealth of other information systems to provide a complete understanding of the effects of various factors such as maintenance, equipment design and production on economics (Roman and Daneshmend, 2001). This will lead to a better understanding and implementation of the opportunities to enhance the performance of the mine through interaction of the mine operations."

Jan 1, 2003

By Dale Ramsey

During Phase IV of our Landfill Mine Stabilization project at a coal burning power generating station, it was determined that a coal barrier pillar separating two abandoned areas of the deep mine had to be breached prior to expansion of the ash disposal area. The proposed plan by the landfill design engineers involved using a high pressure jet cutting tool to cut a slot to allow water flow to an existing industrial waste water treatment facility. Our plan proposed using explosives to breach the pillar from the surface reducing earth disturbance in a high quality watershed while reducing the project cost and accelerating the project time schedule. Many issues surfaced with the proposed change of using explosives. There were a number of lessons learned from this case history and is the primary basis of this paper.

Jan 1, 2003

By H. W. Wainwright

.1. The purification pilot plant and the equipment, solution, and gas cycle used for removing hydrogen sulfide and carbon dioxide are described. 2. As sulfur recovery is necessary in any large Fischer-Tropsch plant, pilot-plant runs were made at 300 p.s.i.g. to study the efficiency of tri-ethanolamine solutions in removing selectively hydrogen sulfide from gases containing varying amounts of carbon dioxide. 3. Aqueous solutions of TEA of 20, 30; 35, and 50 percent were investi¬gated. Data indicate that 30 to 35 percent is the optimum concentration if both selectivity and economy are considered. Slightly better selectivity is obtained with the.20 percent solution, but steam consumption is greater owing to the higher solution rates. Results from our pilot plant runs indicate that a 50 percent solution not only produces an acid gas of lower hydrogen sulfide content but also requires high solution rates to effect hydrogen sulfide purification. 4. Data from 37 runs using TEA are presented in tabular form. In addition, the data are correlated and presented in three sets of curves. By using these curves, it is possible to calculate the compositions of the purified and acid gases for various raw gas mixtures. 5. In cooperation with the Southern Natural Gas Co., investigations were carried out at 300 p.s.i.g. on the simultaneous removal of hydrogen sulfide and carbon dioxide, from gases using various concentrations of diethanolamine. 6. Data from 17 runs employing 20, 30, and 40 percent DEA are reported in both tabular and graphic form. 7. A comparison of the data from one DEA run made at 200 p.s.i.g. with those from the runs operating at 30O p.s.i.g. shows float the absorption capacity of the solution, and, hence, the steam requirements per gallon are about the sage for both pressures. .The only real advantage of the higher pressure is the additional volume of gas that can be treated. 8. The quantity of steam needed to reactivate fouled TEA and DEA solutions increased as the reactivator pressure was increased about 1,0 to 1.1 pounds of steam was required for each gallon of circulating solution when the reactivator was operated at 5 p.s.i.g. 9. A curve is included that shows the effect of the hydrogen sulfide con-centration in a lean 35 percent TEA solution on the hydrogen sulfide content of the purified gas and on steam consumption for reactivation. 10. Both TEA and DEA reduced the organic sulfur content of the raw synthesis gas considerably. Analyses of the lean amine solutions showed a gradual build up of sulfur compounds, indicating that the compounds formed by the amines and organic sulfur do not break down under the ordinary operating conditions of the reactivator. 11. Considerable operating difficulty was encountered in the pilot plant owing to foaming of the amine solutions. Laboratory experiments in which the effectiveness of certain antifoam agents was studied showed Alkaterge C to be most promising for the particular conditions studied.

Jan 1, 1952

By Wern-Ping Nick Chen

Durability risks for underground facilities can be underestimated during design phase as compared to well-known geological risks. However, unclear durability requirements can result in construction schedule delay and change orders. Unlike bridges or buildings, a unified underground durability code or standard does not exist. This paper will provide a durability approach for underground facilities, including degradation modes, mitigations, and compliance measures during construction. In addition, this paper will address how to clearly specify durability requirements in a contract document to reduce disputes during construction and discuss key durability tests that are time consuming and will impact construction schedule if not timely planned.

Jun 23, 2024

By S. T. Reese

STATISTICS of injuries in the quarrying and related industries in the United States first became available when the Bureau of Mines collected reports from the operating companies for the calendar year 1911. Since then reports have been collected annually. The present bulletin, covering the calendar year 1952, is the 33d publication containing statistical data on injuries at quarries and related plants, and it is the first to be published since 1944. The last publication was Bulletin 458, Quarry Accidents in the United States during the Calendar Year 1942. The unpublished statistics for 1942-51 may be found in the Appendix of this bulletin. The Bureau of Mines is authorized to collect data on injuries at quarries, but there is no Federal law that compels operators to supply such data, and the reports received from operators are voluntary responses to the Bureau's requests for information. Although the figures presented herein may not be complete for the entire industry, every effort has been exerted to make them so, and the figures given are believed to be thoroughly representative of the hazards to which quarry workers are exposed. Moreover, the figures are com¬parable as between States -which is significant in view of the lack of uniformity among the States as regards classes of plants covered by State laws, classes of injuries covered by State reports, and other factors that tend to make it impracticable or impossible to compare the injury experience of one State with that of another or to comprehend the relative importance of the various causes of injuries in the industry as a whole.

Jan 1, 1955

By Thomas Fraser

"INTRODUCTION The Santa River Valley of northern Peru contains extensive deposits of a good-grade anthracite that offer one of the most accessible sources of solid-fuel supply for South America. This region is served by the narrow-gage railroad of the Corporation Peruana del Santa, which taps the coal fields along the Chuquicara River and terminates at the port of Chimbote, where facilities have been provided for loading coal into ocean-going vessels.This Government-sponsored corporation is prosecuting a vigorous program of development in this region, envisaging an intensively industrialized area around Chimbot Bay, fueled and powered by the anthracite of the upper valley and a hydroelectric generating plant now being constructed in the Cahn del Fate, where the Santa River has cut through the coastal range of the Andes.This development also includes the construction of extensive irrigation works to greatly expand agricultural production in the valley and thus estab¬lish the basis for a prosperous, well-balanced, industrial and agricultural community. It is hardly necessary to point out the importance of the local anthracite-mining industry to this general plan.At the invitation of the Peruvian Government, through the agency of David Dasso, chairman of Corpoacion Peruana del Santa, a technical mission was sent to Peru in March, April, and May 1945 to examine these coals and assist the corporation in promoting preparation of the coal for most effective use in the contemplated expansion of industry and trade."

Feb 1, 1948

The original work statement of this contract was entitles: 'A Accident Analysis Model for Use in Underground Coal Mines.' The contract was scheduled for a duration of 26 months and was to be in three phases: Phase I - Model Development, Phase II - Application of the Model, and Phase III - Installation, Monitoring and Evaluation of the Model. Alter three months in Phase I, it became apparent that much of the needed data for the model was nut available and could not be made available within the original study schedule. Proceeding as plumed would have resulted in a model of limited utility. Personnel from Theodore Barry and Associates and the Bureau discussed the problem in detail and mutually decided to utilize the majority of remaining funds to assist the Bureau in solving these data problems and develop a stronger ongoing capability for safety analysis within the Bureau. Both tie contractor and the bureau officials involved believed that this decision greatly enhanced the Bureau's ability to develop future accident prediction models, whose rigor would greatly exceed what was currently possible.

Jan 1, 1972

By Daniel C. Boteler

Five lignites from the northern Great Plains province were carbonized at temperatures from 500° to 1,000° C in a bench-scale unit. A replicated Greco-Latin square experimental design was employed to allow testing of four independent variables at five levels. Independent variables investigated were temperature, source of lignite (mine), weight of charge, and moisture content of charge. Dependent variables were char yield, tar yield, light-oil yield, tar plus light-oil yield, carbonization gas yield, and carbonization gas heat yield. An analysis of variance indicated that, at the 99-percent confidence level, the independent variables of carbonization temperature, source of lignite, and weight of charge were significant for yields of char, tar plus light oil, and carbonization gas, whereas moisture content was only significant for carbonization gas yields. At the 95-percent confidence level, moisture content significantly influenced the carbonization gas heat yield per pound of lignite charge and the yields of dry tar plus light oil. All dependent variables were determined on a moisture- and ash-free basis. Multiple regression equations for predicting seven different factors of carbonization yields as functions of carbonization temperature and initial composition were developed using computer techniques. Equations for yields of char, tar plus light oil, and carbonization gas were compared with equations previously developed by others at the 500° C level.

Jan 1, 1970

By Y. H. Cheng, D. M. Lewis, V. Castranova, M. W. Barger, J. K. H. Ma, J. Y. C. Ma, W. F. Xin

Bis-basic ethers off fluorene and fluoren-9-substituted derivatives such as tilorone have been reported to inhibit silica-induced fibrosis in rats. The potential antifibrotic potency of 2,7-bis (diethylamino) ethixy fluorine fluorenone (F-9-H.H), fluorenoxime (F-9-one), and fluorenol (F-9-ol) was F-9-axime > F-9-one ~ F-9-H,H > F-9-ol. Since the release of reactive oxygen species and growth factors from alveolar macrophages (AM) in response to silica exposure has been linked to the development of pulmonary fibrosis, the present study was carried out to determine the inhibitory effects of these compounds on rat AM activity in vitro. The following parameters were monitored: (1) cellular viability; (2) zymosan-induced respiratory burst activity (superoxide and hydrogen peroxide release, chemiluminescence, and oxygen consumption) of AM; (3) drug binding to AM; and (4) lipopolysaccharide (LPS)-stimulated interleukin- I (IL-1) release from AM. The bis-basic ethers, at 40 did not affect cell viability when incubated with AM for 30 min, but significantly inhibited zymosan-induced macrophage respiratory burst activity. The inhibitory effect of these agents was F-9-oxime > F-9-one ~F-9-H,H > F-9-ol. Binding of these drugs to AM was time and dose dependent, and exhibited the following binding affinity: F-9-oxime > F-9-one > F-9-H,H > F-9-ol. F-9- oxime was shown to inhibit LPS-stimulated IL-I release by AM in a dose-dependent manner. This inhibition of IL-1 release by AM cannot be explained as a decrease in viability. In addition, these drugs were also shown to impair human fibroblast proliferation in response to serum stimuli without impairing cell viability. These results indicate a positive correlation between drug binding to AM or other cell types and their inhibitory effects on cellular activities including oxygen consumption, superoxide release, hydrogen peroxide secretion, chemiluminescence, IL-I release, and proliferation. The ability of-these bis-basic ethers to modify AM and fibroblast functions in vitro suggests that further investigation of their reported antifibrotic potency in vivo is warranted.

Dec 1, 1996

By J E. (Boet) Coetzee

SAFEX International, as the name suggests, is a global organisation, which has the fundamental objective of improving the safety of operations concerned with the manufacture, storage, transport, and use of commercial and military explosives and pyrotechnic products throughout the world. It is a nonprofit making organisation of manufacturers of explosives from all parts of the world, founded in 1954 with the aim of exchanging experiences within the explosives industry. Every third year SAFEX organises a Congress during which members present papers on selected themes and discuss reports of significant incidents that occurred since the previous Congress. Admission is for SAFEX members only, thereby creating a safe environment for discussing problems “within the family”. The XV Congress will celebrate the Association’s 50th anniversary in Geneva where it was founded. An overview of the Congress indicates its structure and covers aspects such as the training event, technical seminars and the themes for the plenary sessions and associated workshops. The paper also highlights the special event for the chief executives of member companies and the review of incidents that occurred in the industry since the last Congress. The Congress concludes with a social programme for delegates and their partners on the last day.

Jan 1, 2005

By Gordon M. Matheson, David K. Miller

Possible impacts to the water quality and production capacity of ground water supply wells by blasting is a common cause of complaints for blasting contractors, mining companies, and local regulatory authorities. The major complaints of changes in well water quality include; turbidity, discolored water (red, brown, black, yellow and milky water), and nitrate and/or coliform contamination. The major complaints for changes in well water production capacity include: loss of quantity production, air in water and/or water lines, damage to pump, and damage to well screen or borehole.

Jan 1, 1997