Search Documents

By Dong G. Chae

A model for the leaching of oxide ores is developed and II correlated with laboratory tests for percolation leaching of copper oxide are. Using the model, recovery of metal values and lixiviant concentration of the effluent solution at any time may be evaluated. For the copper oxide ore a simplified version of the model is examined for the leaching mechanism consisting of: 1) a surface flush reaction with the highest rate of lixiviant consumption; 2) penetration of lixiviant to react with copper minerals and gangue constituents; and, 3) slow lixiviant consumption, mostly by residual gangue materials. The simplified model is able to explain reasonably the leaching behavior of copper oxide ore by introducing a concept of effective initial size to correct for packing in a bed of fine particles.

Jan 1, 1979

By Clayton M. Rumsey

No producing or developing mines nor known mineral resources are in the Lower Saline Valley Wilderness Study Area. The inactive Bonanza Prospect has low potential for copper-gold-silver resources. Stone and sand and gravel deposits in the WSA do not constitute mineral resources because transportation costs to major markets are prohibitive. INTRODUCTION The Lower Saline Valley Wilderness Study Area (WSA) covers 2,241 acres in southeast California adjacent to and west of Death Valley National Monument (fig. 1). Access to the WSA is by the Saline Valley gravel road 28 mi northerly from its junction with State Highway 190. The junction is about 35 mi southeast of Lone Pine, CA. The WSA is characterized by moderate to steep, sparsely-vegetated slopes; elevation ranges from about 1,800 ft to 3,560 ft.

Jan 1, 1984

By Walter D. Holland

This study was undertaken to determine miners' breathing zone concentrations of diesel exhaust components, to investigate any relationships between these concentrations and vehicle type, the presence of emission controls, vehicle usage, and ventilation conditions, and to make recommendations for monitoring and ventilation requirements. Twenty-four mines including two con l mines were surveyed. Sampling was done for CON, NON, SOx, PNA, aldehydes, and particulates. hi most mines, concentrations of at least one contaminant exceeded one half the standard or TLV. The concentrations of gases arc probably sufficiently reduced by a minimum air velocity of 50 fpm. A sufficient reduction of particulate concentrations may require as high as 400 fpm air velocity. Vehicle age, type, or usage appear to have little or no effect on contaminant concentrations. PNA levels were below detection limits in all but a very few samples. Minimum requirements for routine monitoring should include formaldehyde, COx, NO2. It is further recommended that better definition of the minimum ventilation requirement be obtained.

Jan 1, 1978

By Steve Karl

Introduction Technological advances in mining and processing have started the domestic mining and mineral industry back on the road to competitiveness. A massive trade deficit, however, coupled with foreign competition and more government regulations threaten to slow this recovery. So say mining executives in Colorado and Minnesota. These industry decision-makers agree that their challenge is to continue the technical innovations of their industry. The journey back to profitability and competitiveness means improved products, they say, but at lower production costs. At separate gatherings in January, officials in both states said that they believe their industry is up to the challenge. Worker attitudes will have to change, they understand, and management styles will need adjusting. And, while they are willing to make the necessary adjustments, they are going to need some help. Or, at the very least, less interference from the federal government. Foreign markets, all but closed to American products, must be opened up on a reciprocal basis. The nation's $170 billion trade deficit is a priority item that can no longer be ignored. And, closer to home, federal and state environmental regulations concerning mineral production must themselves be monitored. 1987 in Colorado While Colorado's service and trade industries should have a fairly good 1987, the state's mining industry can expect another disappointing year filled with layoffs and declining profits, according to the Colorado Mining Association. Once again, foreign competition and government regulations are seen as the main reasons for the mineral industry's woes. And state mining officials see little relief until at least the 1990s. Speaking to a group of reporters at its annual press briefing in Denver, CMA officials said Colorado's overall nonfuel mineral production is expected to fluctuate between a flat and declining growth trend. Mining employment in the state is expected to fall by 400 people this year, to about 7500. In 1981, Colorado mines employed as many as 17,800 people. During the 1970s and early 1980s, the employment rate in mining in the state grew by 12% annually, according to a summary report compiled by the CMA. Last year, worldwide molybdenum production continued to exceed demand US moly producers, therefore, were forced to continue their familiar path of production cutbacks, as well as workforce reductions. And some molybdenum mines in the US closed altogether, the CMA report stated. In Colorado, Amax's Climax and Henderson molybdenum mines operated at about 50% of combined capacity. Climax employed about 200 people at the beginning of 1987, producing about 5.4 kt/d (6000 stpd) or ore. Henderson employed about 700 people, producing about 24.5 kt/d (27,000 stpd) of ore. In coal, the number of licensed coal mines in Colorado has declined from 124 in 1960 to 43 in 1986, of which only 23 were producing. Once a stable source of employment and production, the metallurgical coal industry in the state has only one surviving metallurgical coal mine, Mid-Continent's Orchard Valley mine. High production and transportation costs, weakness in the US steel industry, and a weak market position have contributed to the decline, the summary reported. "The challenge facing most mining companies in the United States today is to survive," said

Jan 3, 1987

By W. G. Pariseau

This contribution focuses on the role of stress analysis for mine planning and the selection of suitable computer programs for the task with special emphasis on coal mine pillars. In this regard, barrier pillars that defend a set of five main entries at the Crandall Canyon coal mine in central Utah were formed during extensive longwall mining north and south of these main entries. Numerical analysis for ground control guided the mine planning and permitting. Retreat mining of pillars led to disastrous events August 6 and 16, 2007, with the loss of nine lives. A most difficult lesson taught by the Crandall Canyon tragedy is the need for education in the selection and use of computer programs for pillar design. Much of this contribution is taken from a report prepared for the Mine Safety and Health Administration (Gates, et al, 2008). Details appear in Appendix Q of the report (Pariseau, 2008). The Crandall Canyon mine is about 16 miles west of Huntington, Utah, in the Wasatch Plateau coal field. Geology of the Wasatch Plateau is described by Doelling (1972) as gently dipping Cretaceous sandstones, mudstones, coal seams, and shales. Joint systems are present in strata above and below coal seams where cleat systems are present as described by Hucka (1991). Several major fault systems transect the field and form grabens with 450- 760 m of drop. One such structure is Joes Valley fault that crosses the Crandall Canyon mine. Mines in the Wasatch Plateau are generally developed from outcrops in steep canyon walls. Overburden increases rapidly as mining progresses into the plateau; mining depth varies with topography between 450 and 600 m in the region of interest. A stratigraphic column derived from a borehole into the mine is shown in Figure 1. There are 11 layers in the column.

Jan 1, 2011

By S. Junnikkala, K. Föhr

"Experiments were performed with plant feeds with a continuous 1,8 m3 cell at Pyhasalmi mine with Cu flotation feed in order to test the applicability of the bubble surface area flux as an indicator of the flotation rate constant. It was found that bubble surface area flux could not predict the rate constants of coarse Cu containing fractions. In the middle size fraction, the correlation coefficient in the rate coefficient estimation was higher but not statistically significant. Only the fine fraction showed a linear relationship with a moderate correlation coefficient.The bubble surface area flux was shown not to be a function of the impeller velocity above a threshold value. The flux was an almost linear function of the superficial gas rate enabling to use the superficial gas rate instead of flux if the operation of an existing cell is to be estimated.INTRODUCTIONBubble area flux seems to offer a simple way of modeling flotation. It relates the flotation rate constant with the bubble surface area flux by a simple linear equation. Due to this, there has been a considerable interest in using the bubble area flux for flotation computations. It has even caused claims that a cell producing a high bubble surface area flux automatically produces a high rate constant and therefore a high recovery.This paper discusses some of the assumptions of the relationship and gives some plant results during two sampling campaigns.The bubble surface area flux s b is describing the area of bubbles available for flotation in a cell per unit area. The bubble surface area flux is related to the superficial gas rate J, by the Sauter mean diameter as follows"

Jan 1, 2001

By Gary B. Glass

Seventeen percent of US coal production now comes from the 19 surface coal mines in the Powder River Basin of northeastern Wyoming. The Powder River Coalfield, which coincides with this topographic and structural basin, is unique to the conterminous US, in that it contains an estimated 934.4 Gt (1.03 trillion st) of in-place coal resources. At least 13.2 Gt (14.6 billion st) is a compliant, strippable reserve base. In 1993, an estimated 162 Mt (179 million st), or 98% of the coal mined in this Wyoming coalfield, came from the thick - average 30.5 m (100 ft) - subbituminous, Wyodak coalbed, or from the Anderson and Canyon coals in the one mine where the Wyodak is split into two separate coalbeds. The other 2.7 Mt (3 million st) of coal mined in the Powder River Basin in 1993 came from the School, Badger, Monarch and Deitz No. 3 coalbeds. In this "world class" coalfield, there are at least 13 other persistent, 3 to 15 m (10 to 50 ft) thick, coalbeds as well as the Big George and Lake De Smet coalbeds, which are each 61 m (200 ft) or more thick in places. None of these latter 13 coals are mined at this time.

Jan 1, 1994

Outotec?s direct leaching process is an atmospheric leaching process for sulphidic zinc concentrates. The direct leaching process, based on special leaching reactors developed by Outokumpu, is the most economical way to produce electrolytic zinc. The production scale applications of the process realized so far are in use at Boliden?s Kokkola and Odda zinc plants. A new full-scale application of Outotec?s direct leaching process will be started in 2008 in China. The process is integrated to the existing production plant, replacing part of the old production facilities by modern technology. Besides high zinc extraction the plant expansion and modernization offers also indium recovery, iron precipitation and solution purification processes. The process equipment includes tailor-made reactors designed on the basis of the work and experience of Outotec research center. Keywords: zinc, concentrate, atmospheric leaching, technology, indium, iron precipitation, solution purification, Outotec

Jan 1, 2008

The National Mining Hall of Fame will induct five mining greats on Saturday, Sept. 17, 2005 at the Museum Convention Center in Leadville, CO. The 18thAnnual National Mining Museum and Hall of Fame Induction Banquet will begin with an open house and reception at 5:30 p.m., followed by the dinner and program at 7 p.m. The five inductees are Nathaniel Peter Hill, John Munro Longyear, John McDonald, Julius Eckhardt Raht and John Dennis Ryan. Nathaniel Peter Hill (1832-1900) built the first successful smelting operation in the Rocky Mountains in1867 at Black Hawk, CO. From 1879 to 1885, he was a U.S. senator. He also taught courses at the Colorado School of Mines.

Jan 1, 2005

By A Bouazza, J Kodikara

In this study, 23 samples of leached ash (LA) were collected from an ash pond at Loy Yang Power Station and geotechnically characterised. The samples were collected at various depths and locations within the ash pond on two separate occasions in order to account for the full variability. The LA within the ash pond at Loy Yang Power Station (LYPS) was found to vary in texture from silt to sand, depending on the location from where the sample was collected. Samples collected near the ash pond inlet discharge point, for instance, contained more than 50 per cent sand sized particles and were subsequently classified under the Unified Soil Classification System (USCS) as silty sand (SM). Further downstream of the inlet discharge, the LA became progressively finer and was classified accordingly as elastic silt (MH) when the sand content became less than 50 per cent. Basic geotechnical testing revealed that the LA from Loy Yang Power Station was generally acceptable as a landfill cover material. The permeability of LA, however, was generally too high for prescriptive covers, (ie resistive covers that generally rely on the impervious nature of the material to control percolation). Alternative covers, generally rely on the store/release function of a capillary or monolithic barrier to prevent percolation into the landfill. Subsequently, a material that can maintain a high water storage capacity while at the same time, readily allow infiltration and evapotranspiration is required for an alternative cover. Sandy silt and silty sand are optimal soils for alternative covers, as they do not yield water to gravity forces, but do give up most of the water in their pores when subjected to high-matric suction (Kavazanjian, 2001). The effectiveness of alternative covers is ultimately assessed using computer models, such as UNSAT-H and HYDRUS-2D, to rigorously perform water balance calculations. Prior to using a computer model to determine the highest possible percolation in the worst climatic conditions, it is necessary to select the most appropriate materials. This paper suggests a method to screen available materials for use as an alternative cover material on the basis of the soil water characteristic curve (SWCC).

Jan 1, 2003

By H. A. Taylor

Graphite is elemental carbon that crystallizes in the hexagonal system as six-sided platelets. It occurs naturally and is mined. And it can be made artificially from petroleum coke in the form of shapes (electrodes) and powders. The market for most kinds of graphite in most end-uses was good in 2004. The 2005 graphite market looks positive. The major graphite prices, as given in Industrial Minerals, remained unchanged throughout the year. The preliminary 2004 U.S. Geological Survey (USGS) prices for natural graphite showed almost no change for crystalline flake. They were $600/t ($544/st) in 2004 and$622/t ($564/st) in 2003. Mexican amorphous graphite was almost unchanged at $150/t ($136/st) in 2004 from$152/t ($138/st) in 2003.

Jan 1, 2005

By W. J. Wenger

Colorado has been producing petroleum since 1863 but only recently has become a major oil State. The first well was drilled on Oil Creek near Florence, but out-put was relatively small until discovery and development of the Weber sandstone reservoir at Rangely. Oil was discovered in the Weber sandstone in 1933, and the reservoir was developed after 1940, bringing Colorado, in 1949, to 11th place among the 48 States as an oil producer. Colorado's output increased further because of the discovery and development of many fields in the Julesburg Basin since 1949 By 1954 Colorado was in ninth place and maintained that position through 1955.4/ Between 1946 and 1951, Colorado's oil production more than doubled, while the total United States production increased only 25 percent. It seems probable that production will continue to expand in Colorado for many years. This report presents analyses of 92 crude oils from 73 fields representing 90 percent of the production in 1955. Abridged analyses are listed for easy comparision, and complete analyses arc given in the appendix. Oil samples were collected for study from many different sources. Although many of the newer fields were not sampled, their oils probably are very similar to those from corresponding formations that were studied and tabulated.

Jan 1, 1957

By I M. Howard

With the bell-less top (BLT) charging system replacing the centuries old double bell charging method, the furnace efficiency has been greatly improved together with considerable reduction in the furnace down time and operational problems. But still there are many draw-backs which need further attention to achieve better efficiency and operational effectiveness. The performance and operational problems of the BLTs have been highlighted and possible solutions to overcome some of the major problems are discussed.

Jan 1, 1999

By P. Rosten

US mine production of iron ore in 1984 showed some improvements compared to 1983. But reduced demand from the iron and steel industry caused temporary shutdowns of many iron ore mines and pelletizing plants. US raw steel production in 1984 was slightly above 1983, but still at a depressed level. Production was 83 Mt (92 million st), compared with 77 Mt (85 million st) in 1983 and 68 Mt (75 million st) in 1982. Two major production trends continued in 1984. They were the increased production from electric furnaces and the growing use of continuous casters. Electric furnace production included 33.2% of the steel poured in 1984, compared with 31.5% in 1983. Continuous casting was used for 39% of 1984 steel production, compared with 32.1% in 1983. Statistical Process Control Statistical Process Control (SPC) has taken on new proportions in the iron ore and steelmaking industries within the last year. This mathematical technique is used to monitor, control, evaluate, and analyze a manufacturing process. The technique charts variability of important quality parameters. Training and adaptation of SPC techniaues for process control have been initiated at Inland, Steel's Minorca, Pickands-Mather's Hibtac, Cleveland-Cliff's Empire and Sherman operations, and at Reserve Mining. One of these operations has requested its bentonite supplier provide SPC charts on quality specifications. Some of the steelmaking operations (Inland Steel, Bethlehem Steel, Dofasco, LTV Steel, National Steel, Stelco, Weirton Steel, and Wheeling-Pittsburgh) have set up SPC programs within their operations. And they also have insisted that some of their suppliers use SPC. Plant Shutdowns The permanent closure of Stelco's Griffith mine at Red Lake, Ontario, has been delayed by one year. This gives employees more time to adjust. The mine is now set to close in April 1986, instead of April 1985. Sidbec (Canadian government) and its other partners (including British Steel Corp., Quebec Cartier Mining, and US Steel) closed its iron mining operations at Gagnon, Quebec. The pellet plant has been leased to Quebec Cartier. New Iron Ore Operations The massive Carajas iron ore project in Brazil is scheduled to come onstream in Jan. 1986. It is to achieve full-scale commercial shipments by July of that year. The 66% iron crude ore requires only crushing and screening before shipment. The product consists of 83% sinter feed and 17% coarse ore. Annual production capacity will be 32 Mt (35 million st) when the project is completed. Principal customer for the ore is Nippon Carajas Iron Ore Co., a consortium of Japanese steel mills. The Arab Iron & Steel Co. (AISCO) has started up a $US300 million, 3.6 Mt/a (4 million stpy) iron ore pelletizing plant built by Kobe Steel Ltd., at Al Hidd-hide in Bahrain. By 1986, this grate-kiln-cooler plant will supply high quality iron ore pellets to feed direct reduction plants in the immediate Gulf area and Far East markets. Iron ore supplied from Brazil, Peru, India, and Mauritania provides the feed to the pellet plant. Hydrated lime (2%) is used as a burden.

Jan 5, 1985

By Nielen van der Merwe

Mr Janisch' s comment' in the August issue on Dick Stacey's remarks about safety factors indeed requires wider debate. The example he quoted to illustrate the successful application of the safety factor concept in coal mining, namely the Salamon formula, is to my knowledge the only recognized application of that concept. Not only that, but that particular formula should be used only for what it was intended, namely to prevent major disasters. It was never intended to indicate long-term pillar stability, and it should not be used for that.

Jan 1, 1993

By Pedro E. Sarquís

Durante varios años se ha utilizado los extractos de quebracho como depresores y dispersantes en los procesos mineros. Empero, existe una nueva forma familia de extractos de quebracho modificados que pueden ser aplicados en los procesos de flotación. Estos reactivos orgánicos naturales, extraídos del quebracho, se aplican en bajos consumos y por tratarse de productos de origen natural, se presentan como una alternativa limpia en relación a los reactivos tradicionales. En ese sentido, el presente trabajo señala la utilización de diferentes extractos de quebracho modificados, dispersantes y depresores, en los ensayos de flotación de sulfuros y también en minerales no metalíferos, donde su aplicación no solo permite mejorar la selectividad, sino mejorar la recuperación de los minerales valiosos.

Sep 12, 2005

By T. A. Rundle, K. Kim, W. M. McCabe, E. C. Gregory

Overcoring tests were conducted at the Near-Surface Test Facility(NSTF) to assess the suitability of five techniques (U.S. Bureau of Mines borehole deformation gauge (BDG), Commonwealth Scientific and Industrial Research Organization (CSIRO) hollow inclusion stress cell, Luleå triaxial gauge (LuH gauge), and Council for Scientific and Industrial Research (CSIR) doorstopper) for in situ stress determination in a closely jointed basalt. This effort is in support of the Basalt Waste Isolation Project, which is studying the feasibility of locating a nuclear waste repository in the basalts of the Hanford Site in southeastern Washington. This paper presents the results from the overcoring study that formed the basis for selection of two techniques to be used during the further exploration of the basalt formations at depth.

Jan 1, 1983

By A. Juganda, F. WILSON, H. PINHEIRO, N. SANDOVAL, J. F. Brune, G. E. Bogin Jr.

To evaluate methane explosion hazards in longwall coal mines, a CFD model was developed along with a 1/40th-scale, optically accessible model of an underground longwall coal mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met for accurately representing the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure, and gas concentrations. This research will help develop strategies for methane monitoring that prevent methane ignitions and explosions in longwall coal operations.

Aug 15, 2022

By Y. G. Li

The design and construction of the hand-dug caisson pier foundation of the Shenzhen International Trade Centre are described in the paper. In addition discussions and inquires about the load-bearing capacity of the hard bedrock are offered.

Jan 1, 2010

By Robert L. Lagace, Michael A. Grossman, Alfred G. Emslie

This supplement to the final report is a collection of interim and monthly reports and working memoranda prepared during the course of this program to document the progress, methods and results of the work. The supplement is divided into the self-contained sections briefly described below. I. SELECTED MONTHLY TECHNICAL LETTER REPORTS - This section is a collection of selected monthly technical letter reports that briefly summarizes the chronological development of the analyses and results, including the different concepts, theoretical approaches, and methods of data reduction and analysis explored, and the discoveries, insights and findings made along the way. More detailed treatments of the key developments and results are presented in the interim reports and working memoranda reproduced in subsequent sections of this supplementary report, and in the separately published final report. II. BACKGROUND THEORY FOR MEASUREMENT PROGRAM ON MEDIUM AND HIGH FREQUENCY RADIO TRANSMISSION IN COAL SEAMS - Working Memorandum - This working memorandum gives the initial background theory needed to guide the planned measurements and data analyses of this program to describe the propagation of radio waves-in coal seams for the frequency range of 50 to 5000 kHz. III. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION - Interim Report - This interim report presents detailed treatments of the data analysis and modelling techniques used, and the associated results obtained from conductor-free area propagation data measured by T. Cory in the first set of six coal mines. The mines were located in three highcoal seams; the Pittsburgh seam in northern West Virginia, the Pocahontas No. 3 seam in Virginia, and the Herrin No. 6 seam in Illinois. IV. ANALYSIS OF MF PROPAGATION DATA FROM MARGARET NO. 11, NANTY GLO, EHRENFELD, AND ADRIAN COAL MINES - Interim Report - This interim report presents detailed treatments of several improved data analysis and Modelling methods applied to, and results obtained from, conductor-free area propagation data measured by T. Cory in the second set of four coal mines. These mines were located in three low-coal seams; the Upper Freeport seam in Pennsylvania and West Virginia and the Lower Freeport and Lower Kittaning seams in Pennsylvania. In addition, this report contains a reprint of two papers presented at a Bureau of Mines sponsored EM Guided Waves in Mine Environments Workshop held in Boulder Colorado. One paper describes the three-layer theoretical model and its application to the conductor-free data from the first six mines, while the second paper describes the theory developed for the coupling of loop antennas to a cable in a mine tunnel in a coal seam, and the model's application to data in the vicinity of cables taken at the Margaret No. 11 mine. V. A METHOD FOR NONINTRUSIVE, IN-SITU MEASUREMENT OF COAL AND ROCK CONDUCTIVITIES IN A COAL MINE TUNNEL - Working Memorandum - This working memorandum briefly describes a possible direct method, and its potential advantages and shortcomings, for performing in-situ measurements of coal and rock conductivities. VI. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION FROM 50 to 5000 kHz - Interim Report - This interim report presents a summary comparison of theoretical and experimental results for conductor- free areas in eleven coal mines located in seven coal seams. It also summarizes the findings and their implications for intrinsically-safe, portable radio communications between roving miners.

Jan 2, 1980