Search Documents

By M. B. Balachandra

A three-dimensional finite element analysis was performed of an instrumented section of a double-entry coal mine in order to provide a comparison between field measurements and existing analytic techniques. The BMINES computer code was used to perform the analysis. The sequence of excavation of the entries was considered, as well as the installation of rock bolts and cribbing during the mining cycle. The materials In the region under investigation were idealized into four rock types and coal. The rocks were assumed to be isotropically elastic, perfectly plastic. Coal was represented by an elastically anisotropic (transverse isotropy) and plastically isotropic model. A fracture yield criterion of the Coulomb form was used for all materials. The strength and stiffness of all materials were substantially reduced from available laboratory data to account for in-situ properties. Qualitative trends and stress distributions obtained from the calculation were found to be reasonable. However, computed displacements and closures were greatly exaggerated and an excessive degree of inelastic deformation was indicated in the coal, especially adjacent to the excavated faces. It was established that both these effects were the result of an excessive reduction in the strength and stiffness of the materials. The analysis underscores the need for three-dimensional calculations by identifying a number of important structural response parameters that would be either outside the scope of, or misrepresented by, two-dimensional analyses. The analysis also emphasizes the need for comprehensive and accurate measurement of material properties in order fully to exploit the power of the analytical techniques to generate reliable predictions.

Jan 1, 1976

By William R. Bond, Jim V. Rouse

Introduction The pressure/vacuum (p/v) lysimeter or soil water sampler has become useful for monitoring vadose zone or unsaturated zone water conditions. The soil water sampler was first introduced around 1961. It was used as a monitoring and research device for studies in agriculture and soil contamination around landfills. Since then, it has been used for many purposes. The use of p/v lysimeters at mining facilities to monitor for solution loss is a relatively new idea. The primary purpose of the lysimeter here is to function as an early warning system. It detects leakage through liners of tailings ponds, heap leach pads, and leachate holding ponds. Their use has proven valuable for collecting baseline data and detecting loss of precious leachate fluid. Different lysimeter designs are capable of vadose moisture sampling from near the surface and down to 90 m (300 ft). They are also capable of sampling soil moisture or saturation plume contaminants from areas not accessible by conventional water well installations. The most common installations are usually simple and cost-effective. In many cases, they can be installed without the use of heavy drilling equipment. A properly placed and installed lysimeter can detect solution leaks in several days or weeks. A conventional perimeter monitor well may take months or years to detect a leak of the same magnitude. A discussion on the general design and installation of p/v lysimeters will give an understanding of its versatility. Three case studies of lysimeter installations at mining sites will be examined in detail. Design, Installation, and Sampling Design The basic design of a p/v lysimeter chamber consists of a porous material through which the soil is drawn into a collection chamber. Access tubes run from the unit to the sample station at the ground surface. Most units currently available range from 25 to 76 mm-diam (1 to 3 in.-diam). The sample collection chamber, or body, can vary from 0.6 to 1.8 m (2 to 6 ft) in length. The body can be constructed of PVC casing or Teflon, depending on the installation desired. The collection chamber functions as a holding reservoir for the collected soil moisture. The intake, or porous material, on the lysimeter is the most complex and vulnerable portion of the unit. The pore size selection varies based on the needs of the installation, type of fluid to be sampled, and type of soil material surrounding the unit. Teflon (PTFE) and porous ceramic are used in fabrication of the porous inlet portion. When using a Teflon material, which is hydrophobic, a larger pore size of 70 µm is needed to overcome surface tension and draw water into the collection chamber. It is typically used at sites involving organic contamination, because of its inert properties. Ceramic material is generally hydrophilic, having less surface tension. Therefore, it has a smaller porosity range to conduct the moisture through the porous medium while under vacuum. Pore sizes may be selected from 0.16 to 6 µm, and can be manufactured for the specific needs of the installation. The final major design component of the p/v lysimeter is the access or sampling tubes. The tubes are usually of 6.3-mm-outside-diam. (0.25-in.-outside-diam). They are made of rigid polyethylene or flexible Tygon with a wall thickness of 1.5 mm (0.06 in.). The con-

Jan 4, 1985

By R. Oler

The need for yieldable ground support, particularly in high stress or deep mining conditions, has grown in recent years. This paper highlights some of the current industry limitations and provides selection criteria for a new yielding ground support system, DSI?s Dynatork Bolt. This bolt distinguishes itself by withstanding 16 ? 30 kJ of energy deflecting loads anywhere from 7 ? 20 tons (depending on the energy). A summary of the laboratory test results and case studies will also be presented as a measure of the performance of this dynamic product.

Jan 1, 2012

The mining industry continues to faces significant challenges due to increasing resource constraints (quality of ore bodies, water, energy, human resources) and increasing license to operate requirements (safety, health, environment, location) from society, employees and shareholders. Technology advancements and hence research are necessary to ensure that the industry remains viable in this changing environment. Collaborative research is an important part of a company's research portfolio and offers the opportunity for the industry to work on generic issues that it is facing. Obvious benefits include the reduced cost to individual companies by sharing the costs, the opportunity to leverage government funding and the opportunity to conduct longer term projects resulting in skills development (PhD and MSc). Limitations of collaborative research include the reduced focus on company specific issues and the loss of competitive advantage from owning the outcomes of the research. The challenge for researchers and research managers is for them to demonstrate the value derived from longer term, pre-competitive collaborative research. The competitive advantage is not necessarily derived only from the outcomes of the research but rather from the company's ability to direct the research, translate the generic research outcomes to address company specific issues and to implement improvements at its operations. Implementation remains the greatest challenge. In this paper, case studies of selected collaborative research projects are presented to demonstrate key success factors required for implementation of research outcomes. This is an ABSTRACT ONLY. A full-length paper was not prepared for this presentation.

Sep 13, 2010

By Derek J. Penrice

A critical element of the Transbay Transit Center Program, the Caltrain Downtown Extension (DTX) will extend commuter rail service into downtown San Francisco and accommodate future statewide high-speed rail service. The DTX project includes 1.8 miles of underground construction, comprising significant sections of mined and cut-and-cover tunnel. At the request of stakeholders, an updated cost estimate was prepared early in the project?s preliminary engineering phase. Unsurprisingly, this yielded a cost substantially higher than the available budget. This paper provides a summary of the management processes and planning decisions taken to bring the project back to budget, resulting in a configuration which derives maximum value from available funding and retains maximum flexibility for future system expansion.

Jan 1, 2008

Jan 1, 1967

By A. P. I. Popoola, T. J. Olaniyi, A. A. Adeleke

"A laboratory froth flotation experiment was conducted on a low-grade carbonatite copper ore sample obtained from Phalaborwa in the Limpopo province of South Africa. The sample was a homogenous hydrocyclone overflow which serves as the feed to the flotation cells at Palabora Mining Company (PMC). The sample has an average copper assay of 0.59% with predominant copper-bearing minerals being chalcopyrite, bornite and cubanite. The carbonatite nature of the ore comes from the high content of calcium (28.85%) and magnesium (6.84%) minerals. Collectors used were sodium diethyl dithiocarbamate and potassium ethyl xanthate alongside Senfroth 38 supplied by Senmin. The results showed that at 200 g/t mixture of collectors (50:50), an optimum grade of 8.03% Cu in the rougher flotation concentrate was achieved at 74% recovery, while during the second flotation, 24.65% Cu was obtained at 74.4% recovery using a Senfroth 38 dosage of 6 L/t with 100 g/t mixed (50:50) collectors. The particle size and pH value of the pulp played a significant role in that the mixed collectors performed efficiently at pH above 8.3 and at room temperature while particle sizes greater than 53 µm were well concentrated when compared with those of less than 53 µm. INTRODUCTION The need for copper ore concentration research is on the rise as a result of the depletion of deposits and the advent of low-grade copper ores. Although most copper ore deposits have other valuable minerals that support their economic extraction, the increase in technological innovations as regards copper usage and applications has increased the demand for copper. Several factors influence concentration results in a froth flotation column, of which the reagent used is most influential."

Jan 1, 2015

By Bryan R. Carmenati

This report documents the need for formal health and safety, and equipment operations training in the mine construction industry. The outlines, objectives, and training texts were developed based on the recommendation of needs of mine construction personnel, and those of Dames and Moore (Safety Analysis of Shaft Sinking operations, 1977) and Kinton, Inc. (A Training Program for Conventional and Raise Drill Construction Personnel; Phase I, 1979). The training material samples contained herein (and under separate cover in its entirety) are designed to improve the safety and production of those in mine construction. An instructor-directed presentation is recommended. The results of the study are presented in the Findings and Recommendations section of this report.

Jan 1, 1982

By Bryan M. Maybee

The scheduling of underground mining activities is a complex task, in particular because of the requirement to satisfy a large number of constraints. A Schedule Optimization Tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated by means of a case study. The main components of SOT include: a genetic algorithm, which searches for optimal schedules; guidance, the application of heuristic rules to guide the genetic algorithm; and sliding, which implements just-in-time development. For the case study, SOT is employed to generate schedules at various ore capacities, accounting for the appropriate financials in each schedule evaluation. The case study finds that preliminary scheduling performed before invoking SOT, intended to provide a good starting point for the search, does not ultimately lead to higher value schedules. Two key uses for SOT are identified. A mine planner can save time by using SOT to produce high-value scheduling alternatives. This process ensures a broader investigation of the value that the deposit can yield. Also, SOT can be used to validate strategic and tactical decisions, by scheduling under alternative scenarios. Both uses produce high value schedules conforming to all imposed resource constraints.

May 1, 2009

By Jueun Lee, Jong-Hwa Yoon, K. Rider, Bernard J. Martin

Whole body vibration is known to affect movement accuracy [1], however little is known about changes in the organization of movement and movement strategies used to limit the influences of perturbations. The specific aim of this work is to analyze the motion and coordination of upper body segments of seated operators performing reaching tasks under whole-body sinusoidal vibration exposure and simulated vehicle ride motion. The long-term objective is to model reach coordination and predict the dynamic behavior of the upper body motion under vehicle vibration exposure. Method The reach task consisted of pointing with the right hand index finger to targets located on touch screens placed in front of the subject, 45° overhead and 90° to the right in the mockup cabin of an HMMWV placed on a 6 DOF ride motion simulator. The task was performed under stable (no vibration) and vibration (sinusoidal vibration or simulated ride motion) conditions. A motion capture system was used to record kinematic data of reflective markers to recreate body link trajectories. Joint angles (torso, shoulder and elbow; Figure 1) were then computed using quaternions. Coordination between body links was defined as a) the joints angle-versus-angle relationships between the upper arm and lower arm, and b) the joint motion onset relationships between torso, upper arm and lower arm in the time domain. Results Angle–versus-angle relationships. The relationship between upper arm vs. lower arm angle and torso vs. upper arm angle for a far forward reaching movement in the stable (solid lines) and vibration conditions (dotted lines) are illustrated in Figure 2. Fig 2A compares the control condition with a 4 Hz lateral vibration while Fig 2B compares the control condition with a 6 Hz vertical vibration. It appears that under vibration exposure the reduced upper arm extension is compensated by an increase in torso flexion. This effect is seen in the last phase of the movements (encircled areas). In addition, the lower arm extension is delayed under 6 Hz vertical vibration (Fig 2B left panel). Time of joint motion onset. The timing relationship between torso, upper arm and lower arm is largely a function of the target to be reached. Examples of delays between body links are illustrated in Figure 3. The control condition is compared to a 6 Hz vertical vibration for three

Jan 6, 2006

By Simon D. Strauss

This article is part of a presentation Strauss made Dec. 3, 1988 at the sixth annual American Mining Hall of Fame (AMHofF) banquet in Tucson, AZ. At the banquet, the Mining Club of the Southwest honored Strauss by naming him the 1988 recipient to the AMHofF. (Industry newswatch, page 6). Introduction In the last two decades, there have been two previous periods of sharply rising copper prices. One was in 1973-74; the other in 1979-80. In both cases, a short period of high copper prices was followed by steep and prolonged periods of low prices. In the language of the market analyst, the high prices were called spikes. Is it likely, then, that three or four years from now the present price of copper will show up as a spike in the charts? There are substantial differences between the current position and the markets of 1973-74 and 1979-80. In 1973-74, US copper prices were subject to government-imposed price ceilings of $0.60 per lb through early December, 1973. These were increased to $0.68 per lb through May, 1974. Meanwhile, mines outside the United States were free of restraint. Rising demand in London pushed the price above $1 per lb in the third quarter of 1973. In early April 1974, it reached a peak of $1.50 a lb. In May of that year, the US ceilings were removed and the domestic price began to rise. What were the causes of this price strength? While ceilings held the domestic price below the world market, domestic consumers acquired all the tonnage offered by US mines. Meanwhile, in the world market, buyers feared prolonged shortages. The Club of Rome had warned that world economic growth would be limited by impending depletion of mineral resources. There was al so concern about a copper cartel that might increase copper prices even more. In early 1974, at a special United Nations session, developing-country spokesmen warned the industrialized world to expect high commodity prices. Also adding to the concerns of copper buyers was the fear that when US wage contracts expired in mid-1974, protracted strikes might ensue. The combined effect of this atmosphere was that consumers accumulated large amounts of copper, far above their normal carry. By midsummer, the position changed radically. While some strikes did occur in the United States, they proved short-lived. The most significant development was a massive economic recession. The energy crisis was causing enormous dislocations in the world economy. Construction activities were sharply reduced and automobile sales plummeted. Public confidence was shaken. Copper sales fell precipitately as consumers decided to draw down their swollen inventories. The price came down too. In April 1974, the London price- as noted-was $1.50 per lb. By the end of the year, it was down to $0.57 per lb. In 1973-74, the copper price rise was fed by fears of shortages, cartels, and strikes. In 1979-80, the market rose on the strength of good demand plus political and military instability. The price rise was also fed by inflationary trends, exemplified by speculation in precious metals. Prior to this second spike in copper prices, the market had been depressed despite economic recovery. Despite reduced US output, copper production in the rest of the world was increasing. Though consumption was rising, surplus stocks reached unprecedented levels. At the end of 1977, the aggregate of stocks at the refineries and in the exchange warehouses was 1.5 Mt (1.67 million st). That was more than three months' shipments at then rates of consumption. In 1978, the statistical position improved. Shipments of refined copper that year were 8% greater than in 1977. The result was reduced visible stocks but -just as was to be the case in 1984-86 - the price remained depressed. In 1979, an even sharper drop in visible stocks occurred as shipments rose by another 4%. This time, though, the price responded. In December 1978, the price in current dollars had been less than $0.70 per lb. By the end of 1979, it was above $1 per lb. And in the first quarter of 1980, it averaged more than $1.20 per lb. Military and political developments were a factor. The hostage crisis in Iran was followed by the Soviet invasion of Afghanistan. To many, it appeared that war might result if the Soviets pushed on into Pakistan. At the same time, speculation drove gold and silver prices to incredible levels. As silver prices rose above $40 per oz), copper above $1 per lb did not seem unreasonable. Then, in March 1980, the precious metals price boom collapsed. Copper prices also retreated, though not as much. In February 1980, the copperprice averaged $1.32 per lb. By December, it had dropped to $0.85 per lb. In 1981 and 1982, the decline continued. The present copper situation Why is the current situation different from these two previous episodes of high prices? First of all, today's inventories are far lower than they were in either 1974 or 1980, when the price declines began. The stocks at refineries and in exchange warehouses are substantially less than they were then. More significantly, consumers today have very limited holdings compared with stocks they carried in 1974 and 1980. Even if faced with a downturn in their own business, copper consumers will not be able to stay out of the market. To the extent they have any business at all, they will have to buy copper. And on the supply side, there is also a significant difference. The year 1988 has been unusual. US production is up sharply, responding to higher prices. But production is little changed in the rest of the Free World. Indeed, several of the major producing countries have mined less copper this year than in 1987 despite the prices increases. Peru has had labor problems that have cut its output. Zambia and Zaire suffer from shortages of expatriate technicians, not to mention spare parts. They also suffer from the failure to maintain equipment or perform adequate development. In Chile, the two largest mines, Chuquicamata and El Teniente, have not met their production targets. Chuquicamata is struggling with high arsenic content in its ore. And, in late 1987, severe rockbursts hampered operations at El Teniente. In addition, depletion of some mines in Australia and South Africa has offset rising output at other properties. Indeed, when final mine output figures for 1988 become available, it may well be

Jan 1, 1989

By Wei Zheng

A pulverized coal fired power plant is being built in Osceola, Arkansas, along the Mississippi River. The subsurface soil conditions consist of a certain amount of very soft clayey silt and clay underlain with a medium dense sand layer and a dense sand layer. The site has been raised four to five feet with fill material consisting of sand and gravel. Consolidation settlement due to the fill is expected to cause negative shaft resistance (downdrag) on the pile foundations. The site is located in a high seismic hazard area - the New Madrid Seismic Zone (NMSZ). The liquefaction analyses indicated that there is a high liquefaction potential in the medium dense sand layer. Load tests are needed to determine the shaft resistance and the end bearing of each soil layer for design purpose. Two types of pile foundations ? augered pressure grouted displacement pile (APGD) and partial augered pressure grouted displacement pile (P-APGD) were considered for this project. Ten pile load tests, including five compression tests and five tension tests, were performed for three different areas. Strain gauges were installed for the compression tests. The APGD and P-APGD piles were installed side by side for comparison. In addition, three additional dynamic tests were performed to supplement the information from the static load tests. Load deflection curves for the compression tests were predicted, and the failure loads were interpreted using four different methods. The shaft resistance and the end bearing were determined from the strain gauge data and were used to back calculate the ultimate capacity. The back-calculated capacities are in good agreement with the predicted failure loads; they were further verified with the tension load test results.

Jan 1, 2007

By J. Matos e Silva

"Abstract Although one can think that it is very low the probability of a seism occurrence during the execution of an excavation in an urban lot protected by a diaphragm wall curtain, reality shows that whenever a seism occurs in an urban area several diaphragm walls will be affected by it. So it is advisable to consider the seismic action when designing a diaphragm wall curtain. The paper refers the main information about the seismic design of diaphragm walls according to the Eurocodes 7 and 8 and to the Portuguese Norms related to them (respectively NP EN 1997-1 2010 and NP EN 1998-5 2010), as the Eurocodes consider the possibility of each European country to adopt their own seismic parameters as the seismic risk is different in each country. Thus the so-called National Document of Application (in our case the Portuguese Norms) prescribes the seismic local parameters.1 - EUROCODES AND PORTUGUESE NORMS PRESCRIPTIONSAccording to Eurocode 8 - Part 5 and to the related Portuguese Norm NP EN 1998-5 2010, seismic actions on soils should be quantified adopting the Mononobe-Okabe method that gives goodapproaches when compared with reality.From paragraph 7.3.2.2 of the referred Norm, the horizontal seismic coefficient kh will be:"

Jan 1, 2014

By S. J. Frank

The development of feedforward semi-empirical control models for furnaces and the evaluation of mass balances are based on plant data. The models can only be as good as the data and it is therefore required to know the inherent uncertainty associated with the plant data. This uncertainty stems mainly from the fact that the slag, alloy or dust, have a distributed nature that depends on the degree of mixedness. It is commonly accepted that melts from open bath furnaces are well-mixed, and submerged arc furnaces less so. The impact of this assumption is significant, as a reasonably homogeneous melt could be represented by one sample only. As so much of metallurgical control depends on the assay information of the alloy and slag melts from furnaces, it was decided to characterise the possible variation in melt chemistry and temperature. Sampling campaigns and continuous temperature measurement of the melts were performed for different alloy and slag taps at a major ferrochrome producer. Both a submerged arc furnace and open arc furnace are evaluated in this way, by way of comparison. The slags of both open arc and submerged arc furnaces were found to be of similar degrees of homogeneity, with much spatial variance in the reducible iron and chromium oxides. However, it was found that the alloy melts deriving from open arc furnaces were significantly less homogeneous than the alloy derived from submerged arc furnace alloy production. The compositional variance could be related to the furnace operating conditions and it affects both metallurgical accounting and process control. In all cases it was found that the variance in melt solute components are larger than can be ascribed to analysis instrument error. It will be shown how this predetermined variance in melt composition could be included in process modelling and control.

Jan 1, 2004

By A. Tor, M. Borowski, N. Szlazak, D. Obracaj

This article presents possibilities of reducing methane emission to the atmosphere in working mines in Jastrzebie Coal Company by means of proecological solution. They form a new approach towards the problem of rational and effective use of natural resources both in economical and environmental respect. Power and thermal energy for underground air conditioning in mining excavations are produced from the methane, which is drained out of the mine for safety reasons.

Jan 1, 2003

By Vidal Navarro Torres

El presente trabajo señala el proceso experimental para determinar la transferencia del calor del macizo rocoso al aire en la atmósfera subterránea, dado que a ciertas profundidades cuando la temperatura de la atmósfera subterránea excede el valor máximo admisible por las normas y estándares de confort o comodidad térmica, se presenta el riesgo ambiental térmico. En ese sentido, el estudio comprende tres etapas: la primera etapa fue dedicada al desarrollo de un modelo matemático que establezca la variación de la temperatura debido a la transferencia del calor del macizo rocoso al aire de la atmósfera subterránea; la segunda etapa consistió en validar el modelo matemático en una mina subterránea de cobre, y la tercera fue realizar una aplicación práctica en dos minas con problemas de impacto ambiental térmico. En consecuencia, la metodología propuesta para la evaluación del impacto ambiental térmico en minas subterráneas se fundamenta en procedimientos científicos plenamente sustentados, cuyos resultados indican su aplicabilidad.

Sep 12, 2005

By Geoffrey D. Collins

This paper deals with the construction of the Effluent Outfall Diffusers which form part of the outfall for the Deer Island sewage project. The work was executed 15 km out to sea in Massachusetts Bay and required the drilling, installation, grouting and accurate determination of the actual position of 55 riser shafts in 33.5 m deep water. Although not strictly a "foundation", the contractor's approach to the installation of the diffusers was a logical development from many marine foundation projects executed by the Contracting companies over the last decades. The only previous application of this design of outfall had been in Australia where offshore oil drilling techniques had been adapted for use in riser installation.

Jan 1, 1994

By Peter Middendorp

Pile foundations are widely applied in the Netherlands because of the soft soil conditions. One of the popular pile types are cast-in-situ piles, which have to be integrity tested to get accepted. Integrity testing has been applied for more than 30 years, with the number of integrity test performed nowadays exceeding 400,000 per year and subsequently there is a substantial amount of practical experience with this testing method. This paper will deal with some basics of integrity testing and describe some of the techniques that have been adopted in the Dutch pile testing practice, like detection of pile head defects with a spike type hammer pulse, and the site average or pile group average for the qualitative interpretation of measured signals.

Jan 1, 2006

By J. M. Barker, V. T. McLemore

Most discussions of sustainable development (SD) in mining relate to metal mines in rural areas. Industrial minerals (IM) are closer to urban areas primarily owing to a high transport-cost component of delivered cost. This visibility to large populations overshadows IMs relatively small operation size and generally lower waste volume and toxicity. The IM industry needs to rethink its way of doing business to fit into the SD paradigm. Society and business in general will also undergo significant change to enable industrial SD along the lines of triple-bottom-line accounting with government pushing everyone. The benefit to IM mining from embracing SD is a renewal in their social license to operate and a rebirth of mining as a positively-viewed force in society. This positive view would lead to lower acquisition costs because society would not fight so hard to eliminate nearby mining. This would ease the current exploration woes of the IM industry by opening up new deposits for exploration and more readily allowing placement of mines nearer to markets. The earlier in the exploration process SD is initiated, the better.

Jan 1, 2004

By Robert Hopler

It is the nature of the initial detonation to the powder around the cap which governs the greater or less effect of the explosion of the whole charge. The cap communicates to the first particles of powder a disruptive impulse, which, according to the nature and strength of the cap, more or less completely overthrows their equilibrium and decomposes the powder with great energy, setting up sympathetic vibrations that explode the particles of powder in turn by the violent disturbances or friction between them in a regular succession of impulses and decompositions, which, if started with sufficient energy, are of such intense heat and velocity that the rupturing force of the explosive is developed practically instantaneously. This detonation has already been shown to be not only the result of mechanical force, but a combination of extremely sudden chemical and dynamical reactions which set up vibrations to which different powders are more or less susceptible, and these explosive reactions will be propagated through the mass of the powder according to the intensity of the vibrations and the resistance with which their motion is opposed by the nature and consistency of the powder, whether it be difficult or easy to oxidize, soft and plastic like dynamite, or hard. If the initial detonation of the powder surrounding the cap is of the highest degree, the vibrations will be most intense and will be propagated further through the mass than by a poorer detonation. Hence the different degrees of detonation. Unless the first particles of powder are so thoroughly decomposed by a detonation of high order, or first degree, as to convey the necessary heat and energy to detonate the whole charge, the greatest force of the powder will not be developed. There will frequently be unbottomed holes or pieces of unexploded powder scattered about, or both, and the air in the mine will be contaminated with some obnoxious gases that have not been completely oxidized.

Jan 1, 2007