Search Documents

By G. Deschênes

The Eleonore property (James Bay district of Northern Québec), owned by Goldcorp, hosts gold within stockworks of quartz-tourmaline-arsenopyrite veins and veinlets contained within microcline (potassic alteration) and brown tourmaline replacement zones. The preliminary investigation to recover gold from drill core samples showed that flotation followed ultrafine grinding and cyanidation is the preferred option. Ultrafine grinding is used to liberate gold finely disseminated in sulphides. The flotation concentrate used in the investigation had a P80 of 11 microns and contained 75.5 g/t Au, 5.0 g/t Ag, 10.3% S, 0.07% Cu and traces of antimony (0.03%). The mineralogical characterization showed the presence of 65% gangue minerals, 23% pyrrhotite (hexagonal), 9.6% arsenopyrite, 2.2% pyrite and 0.08% chalcopyrite with trace amounts of galena (0.05%) and sphalerite (0.03%). Gold was in the form of native gold and electrum. A straight cyanidation conducted at pH 11.0, DO of 3-5 ppm, 2000 ppm NaCN, 20 C 72 hours extracted 97.0% Au and consumed 31.5 kg/t NaCN. The equilibrium was reached within 24 hours. Increasing the dissolved oxygen to 16 ppm reduced the consumption of cyanide to 22.0 kg/t with 96.7% Au extraction. A 16-h pretreatment with 2.0 kg/t lead nitrate, followed by a 24-h cyanidation reduced the cyanide consumption to 6.0 kg/t with a gold extraction of 97.5%. Increasing the lead nitrate addition to 6.0 kg/t reduced the cyanide consumption to 1.2 kg/t by passivating the surface of pyrrhotite. The gold extraction remained at 97.0%. It was possible to decrease the concentration of cyanide to 800 ppm NaCN without compromising gold extraction. The associated cyanide consumption was 1.2 kg/t NaCN. The passivation of gold grains was an issue when the cyanide concentration was decreased to 550 ppm NaCN. The gold extraction decreased to 92.2%. The average lime addition for all the tests was 7.4 kg/t and the average silver extraction was 80%. Efficient cyanidation of an ultrafine sulphide concentrate with only 800 ppm NaCN represents an advance in leaching of ultrafine sulphide concentrates.

Jan 1, 2013

By Clyde L. Brown

The ignition source of fires and explosions in coal mines is sometimes difficult to explain because resulting widespread destruction often erases valuable evidence that might reveal the cause. However, through years of experience, investigators have been able to piece together enough evidence to establish the reasons and, thereby, have been equipped to recommend corrective or preventative measures. The pattern of hazards is not constant. It changes with the development of new practices and new equipment. Important among the new hazards to coal mining are those introduced by electricity. In addition to the dangers of electric shock, fires and explosions from heat and arcs, and premature blasts, certain others have developed as a result of stray electric currents from direct-current traction systems. The conventional direct-current power-distribution system in coal mines is conducive to electrolysis damage to mine tracks, metallic pipelines, grounded power conductors, and structures in a position to become conductors of stray currents. The voltage drop resulting from power demand on intentionally grounded power conductors and accidental grounds on insulated conductors are common sources of stray currents in coal mines. Uncontrolled electric cur-rents flowing through the earth and metallic structures can be a menace, and these contribute to the estimated $6,000,000,000 annual loss caused by corrosion. The purpose of this publication is to discuss some of the electrolysis hazards in the coal-mining industry and to outline corrective measures to alleviate them.

Jan 1, 1962

Media Type Effect on Grinding Efficiency

Sep 13, 2010

By Mike Higgins

"Data management is emerging as a major concern for miners. Engineers today are faced with anextensive array of data from varying sources, and are required to consolidate and analyse thisinformation to produce an effective and efficient mine plan. The viability of a mining operation canbe dependent on the outcomes of this process. With so much at stake, it is no surprise that mostengineers prefer a standard approach to blasting which is designed to minimise risk rather thanoptimise performance."

Jan 1, 1998

By Felix A. Vogel

Rutile concentrate, used in the manufacture of welding rode, smoke-screen chemicals, and alloys, is being produced by the Titanium Alloy Co. of Arkansas at its mine and. mill in Magnet Cove. The company estimates a substantial reserve of recoverable rutile. This is a new operation, and production figures are not known. Previous operations had stripped the placer material, leaving the underlying mineralized zone. INTRODUCTION This report describes the mining and milling; operations of the Titanium Alloy Co. of Arkansas. The property was examined by the author on March 4, 1942, and subsequent dates. J. A. Wood, general manager, was very helpful in supplying information.

Jan 1, 1944

By John Starkey

"During the period June 2007 to March 2007, John Starkey of Starkey & Associates (Starkey) worked in Russia for High River Gold, supervising the engineering design work that was being done at the IRGIREDMET Research Institute, in Irkutsk Russia. The work entailed moving the Newmont No. 4 mill from Elko, Nevada to Berezitovy, a mine site north and west of the city of Skovorodino, in the Amur Region of Siberia. This was a grass roots project and required construction of all phases of the infrastructure and process facilities that are associated with a 5000 t/d open pit mine and CIP mill.During the course of this engineering design exercise, many aspects of doing business in Russia were encountered, with regard to laws, norms, and business practices. This paper discusses many of these findings. Also by living in Irkutsk, many observations on Russian life and social customs were made and these merit discussion from a general interest point of view.Prior to going to Russia, another engineering and ore testing firm (TOMS) had approached Starkey to find out if Starkey could assist them in upgrading their SAG ore testing procedures to Western standards in order to offer their clients turnkey projects, that included reliable SAG and AG grinding. TOMS was aware that Starkey had invented the SPI test but did not know that the SAGDesign test had by then been fully developed and was being offered commercially as the most accurate way in the world to design new grinding mills. They were also unaware that this new testing method had been patented by Outokumpu (now Outotec) and that this method allowed them access to a design method, through Starkey, that would lead to a manufacturer’s guarantee (by Outotec) of throughput and grind for any new semi-autogenous or autogenous grinding circuit, with or without ball mills.When Starkey started working at IRGIREDMET in June 2005, they also made a request to add a design method for SAG mills that would be considered acceptable to Western clients. From these requests, presentations were made in Russian to both institutes and each decided to join the SAGDesign Consulting Group as satellite members and buy a SAGDesign test mill to use with their Bond Ball Mill Work Index mills, to provide SAGDesign testing services. To complete the service, contracts have been put in place for Starkey to use these results to design new grinding equipment and to train engineers at TOMS and IRGIREDMET how to do this work.Starkey also undertook to train engineers at both labs to go into the field and to take the samples for SAGDesign testing programs. It is here where the SAGDesign testing service upgrades other grinding test programs because the samples to be used for design are professionally chosen, and the results will be much more likely to produce a satisfactory design. Starkey is a mining engineer and is uniquely qualified to do this task. This and the SAGDesign test are the key components that lead Outotec to offer a performance guarantee for mills designed by Starkey."

Jan 1, 2008

By Ray W. Ballmer

"For his leadership in developing and managing large, complex, and technically innovative mines, particularly the outstanding and successful Bougainville mine and for his lecture, 'The Moving Targets of Mine Development '. " Recipient of the 1981 D. C. Jackling Award

Jan 1, 1982

By A J. H Newell

The background and the basis for conducting a Technical Due Diligence are discussed as well as the source information, typical studies and potential limitations. Typical short comings including ‘show-stoppers’ are presented for the metallurgical area, with examples. Issues found in other areas such as geology, mining, infrastructure and financial evaluations are briefly reviewed, highlighting the input and interaction required by metallurgists with these disciplines. A checklist is provided as a guide to maximise the success of a Due Diligence as well as a check on the quality of a Feasibility Study.CITATION:Newell, A J H, 2015. Fatal flaws in technical due diligences, in Proceedings MetPlant 2015, pp 61–77 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

The 103rd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 16th August, 2000. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past Presidents, our Members and other guests, among them the following: Reinie Meyer, President, The Geological Society of South Africa Dr Nielen van der Merwe, Chairman, The South African Institute of Rock Engineering Chris Fourie, President, Institute of Mine Surveyors of South Africa

Jan 1, 2000

The effect of conditioning energy input on the metallurgical results of an emulsion flotation process has beenattributed by previous authors to a detergency process.This paper shows that such a process does not explain the data and that an attrition mechanism is more appropriate.

Jan 1, 1970

By Jarrod Bonsmann

"This paper presents the results of small scale testing to examine the effect of various importantparameters on the response of a vehicle due to the detonation of an explosive charge buried inthe soil below the vehicle. In particular, we were interested in examining what effect change instandoff distance, change in mass, and change in surface area would have on the loading applied.We examined the impulse delivered to the target in all cases and for the change in mass andchange in stand-off distance we examined impulse, kinetic energy, and acceleration."

Jan 1, 2012

Project Schedule ?Construction 2005 ?2008 (3 years) ?Operations mid 2008 ?2020 (12 years) ?Closure 2020 ?2023 (3 years) ?Post-closure monitoring Victor Economic Facts ?$982 million investment; ?$110 million already invested in the Project; ?1100 person years of employment in construction; ?375 full time positions during operations;

May 1, 2006

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

By B. C. Peterson

Calumet Division, Calumet & Hecla, Inc., whose operations are in Houghton and Keweenaw Counties, Mich., is a highly integrated and complex organization. This division operates mines, a railroad, a concentrating mill, a reverberatory smelter, and the auxiliary generating plants and shops to service these operations. In addition, it operates a sands reclamation plant, leaching plants, a foundry, and a machine shop that serves varied industries with castings and parts for many applications. Calumet & Hecla, Inc. has produced over 60 percent of all the copper that has been produced in Michigan since discovery of the ore in 1864, and in 1959 the company ranked eight among the country's producers with a production of 17,407 tons. To keep abreast of modern accounting systems developed elsewhere in industry and to combat increasing costs due to higher labor and supply costs, as well as increased costs due to deeper mines and lower grade ore, the company has developed a modern machine cost accounting system. This not only provides the usual bookkeeping and cost accounting facilities but offers accurate cost data for engineering evaluation of the mining operation. This system is credited with being instrumental in permitting continued operation of these high-cost mines in a period of increasing costs with no corresponding increase in the price of metal.

Jan 1, 1962

By Annie G. Smelley

As a part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U.S. Department of the Interior, is developing a dewatering technique that allows for disposal of clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weight nonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater materials containing clay wastes. In laboratory experiments, coal-clay waste, potash-clay brine slurry, phosphatic clay waste, uranium tailings, and talc tailings were successfully consolidated. Coal-clay was te was consolidated from 3-. 6 to 57 percent; potash-clay brine slurry was consolidated from 3.8 to 35 percent; phosphatic clay waste from 15.6 to 49 percent; uranium tailings from 15.4 to 67 percent; tailings from talc production from 9.7 to 53 percent; and an acidic Ti02 slurr slurry from 1.68 to 30 percent.

Jan 1, 1980

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity.

Jan 1, 2000

By S. Kouniali

Experience with knowledge-based systems for Layout planning and roadway support dimensioning is on hand in European coal mining since 1985. The systems SOUT (support choice and dimensioning, 1989), SOUT 2, PLANANK (planning of bolt-support), EXOS (layout planning diagnosis. 1994), Sout 3 (1995) have been developed in close cooperation by CdF1. INERIS2. EMN3 (France) and RAG 4, DMT5, TH - Aachen6 (Germany); ISLSP (Integrated Software for Layout and support planning) development is in progress (completion scheduled for July 1996). This new software technology in combination with conventional programming systems. numerical models and existing databases turned out to be suited for setting-up an intelligent decision aid for layout and roadway support planning. The system enhances reliability of planning and optimises the safety-to-cost ratio for ? deformation forecast for roadways in seam and surrounding rocks, consideration of the general position of the roadway in the rock mass (zones of increased pressure, position of operating and mined panels). ? support dimensioning ? yielding arches, rigid arches, porch sets, rigid rings, yielding rings and bolting / shotcreting for drifts ? yielding arches, rigid arches and porch sets for roadways in seam ? bolt support for gateroads (assessment of exclusion criteria and calculation of the bolting pattern) ? bolting of face-end zones (feasibility and safety assessment, stability guarantee).

Jan 1, 1996

By Bill Parnell

"Friction winders and double drum winders have been used in the vertical shaft mining industry for over 100 years. In that time, there have been many changes made in the electronic and mechanical fields of hoisting, but few changes made in the manufacturing and performance of steel wire rope, until recently.In the past ten years, with the advent of high polymer thermoplastics, the industry has seen some major advancements in steel wire rope. By incorporating a polymer with steel, improvement of rope life and reduction of costly maintenance downtime has been accomplished.IntroductionThe Williams Mine is Canada's largest gold producer with an annual production of some 500 000 ounces of gold from 2.2 million tonnes of ore. The Williams Mine is situated in the Hemlo area of northwestern Ontario, approximately 40 Ian east of the town of Marathon. It is operated by the Williams Operating Corporation which is owned equally by Teck Corporation and Homestake Canada Inc. It is one of three adjacent properties forming the Hemlo gold camp."

Jan 1, 1995

By J. A. Yeats

This paper describes the loading to 25MN of a 1.2m diameter bored cast-in-situ test pile founded in the Thanet Sand which was base grouted. The pile was sleeved over the major portion of its length to test primarily the base response of the pile. The results are presented and compared with similar pile load tests in Thanet Sand.

Jan 1, 1989

By V. M. Shick

For practical purposes of the use of information resources in the field of geomechanics and mine surveying with accepted mining technology in mines, the authors have developed the packaged software programs of the survey-geomechanical information system with database objects of mine field. This system enables to execute the graphical representation of workings layout in preset scale, axonometric projection, the zones of higher ground pressure: program packages for calculations of rock pressure manifestations and for selection of suitable support facilities for the permanent, development and active workings and vertical shafts based on the information resources of the State Research Institute of Mining Geomechanics & Mine Surveying (VNIMI). The program packages are applied at coal mines in Russia and in Kazakhstan. The profitable operation of coal mines can be reached only by the combined optimal engineering decisions in mine working's laying-out and their reliability and safety at the stages of their designing and exploitation, and with minimal harm of the environment as well. This problem is being complicated by the fact that today the mining-practicing engineers and designers are ordinarily facing the problem " of an information barrier", when the complexity of controlling systems exceeds the potentialities of traditional management of production practice. Coal mine is a typical representative of complicated systems, because the information about geological structure, physicomechanical properties and stress-strain state of rock mass are of fragmentary character and insufficiently reliable. A mine has a developed network of interrelated workings, by the way, some of them are productive ones being subjected to control to a certain extent, and some of them are abandoned ones being noncontrollable and hazardous in rushes of water, gas, pulp and fire. The ground pressure forces cause the disintegration of rock mass growing with depth. The progress of mining operations constantly changes the geomechanical situation forming the zones of bearing pressure, stress relieving, coal falling, as well as it leads to the pulp movement on the earth surface, breaks the ground water flow, causes deformations and changes in stability of buildings, constructions and natural objects on the earth surface. One should take into account the existence of hazardous zones within the mine field, i.e. the zones of elevated ground pressure, geological dislocations and those ones under natural water reservoirs, ponds, etc. Major coal seams are prone to rock bursts, sudden outbursts, bleeding, endogenic fire. It is obvious, that in practice it is extremely difficult to account for the mentioned above factors in their interrelation.

Jan 1, 1996