Search Documents

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports.5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolande No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a positive identification of the bed at Yolande No. 6 will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 180. As far as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By Gang Chen

Conventional methods designate a factor of safety, a deterministic number, to indicate the stability of a mine excavation. However, this deterministic description of excavation stability is frequently insufficient or inaccurate and, sometimes, misleading. Employing the probabilistic analysis to determine the likelihood of mine excavation failures will lead to a better understanding of ground control problems and result in more rigorous designs of the excavations. Based on the theory of probability, two approaches are taken in this study for the probabilistic analysis of excavation stability. The first one utilizes direct integrations for the estimation of failure probabilities of mine excavations. Due to the complexity of the integration, this approach can only be applied to solve relatively simple problems. In order to overcome the limitation of the direct integration method, the second approach employs the first-order second-moment approximation of the failure probabilities for more complex ground control problems. The probabilistic analysis offers a deeper insight into the uncertainty associated with the stability of mine excavations. The study indicates that the distributions of parameter values play a significant role in the mine excavation stability, which can not be disclosed by the conventional methods of stability analysis. Greater dispersiveness of the parameter values will lead to a different probability of failure, although the factor of safety estimated by conventional methods stays the same if the mean values of the parameters are constant. By taking consideration of the probabilistic distributions of the parameters, the probability model can provide more reliable designs of mine excavations.

Jan 1, 1996

Diesel Particulate Matter (DPM) issues are very high profile currently in both Australian coal and metal mines and Australian states are generally moving to acknowledge and to broadly follow US 2008 final metal/non metal mine regulation limits of 0.2 mg/m3 submicron particulate matter, 0.16 mg/m3 total carbon particulate and 0.1 mg/m3 elemental carbon particulate. The real time DPM monitor is being developed on the base of the successful Personal Dust Monitor (PDM) unit. The objectives of recently completed Australian Coal Association Research Program (ACARP) study has been to finalize the design of a DPM unit, to undertake comprehensive and internationally recognized laboratory testing to evaluate the new design and to undertake an underground series of tests to establish the robustness and reliability of the new approach. Under the project Thermo Fisher Scientific has undertaken structural changes to the PDM to convert it to a DPM real time monitoring underground instrument, the D-PDM. The Pennsylvania Pittsburgh Research Laboratories of NIOSH (the group that originally contracted for the PDM development) has undertaken laboratory ?calibration or verification? testing. A phase of Australian mine robustness and engineering testing has been undertaken to ensure the instrument can effectively assist mine management to handle this health issue. Tests have been undertaken at points of expected high atmospheric DPM such as during Longwall face moves, Development RAM car, Eimco and PJB usages. The paper discusses how the monitors have performed within the underground mine environment in evaluating DPM during the various phases of the production cycle. They have closely examined the influence of aspects of the mine ventilation system. Results have been compared to alternative industry pollutant measuring approaches. The outcome of the project gives the industry access to an enhanced tool for understanding the mine atmosphere in the presence of DPM. Real time DPM monitoring will allow the industry to pin-point high exposure zones such as those encountered in coal longwall face moves where various vehicles work or in areas of constrained or difficult ventilation. Identifying of high DPM concentration zones allows efficient modification of work practices to reduce underground miners? exposure. Some outcomes of the ACARP project in this area will be discussed.

Jan 1, 2009

By M. Vandewalle

What separates the support of mining openings from the support of similar civil engineering structures is the fact that mine openings have to survive large deformations as a result of changing stress conditions induced by progressive mining. Steel fibres impart to concrete and shotcrete a high degree of ductility which not only allows the shotcrete and concrete linings to absorb important rock movements but also to increase its bearing capacity by a redistribution of the loads. A range of applications will be discussed technically and economically.

Jan 1, 1998

Samples weighing 0·5 g are decomposed with hydrofluoric and other acids. Most elements are extracted ftom the acid, aqueous solution by Alamine 336 (tricaprylyl tertiary amine) and thorium is determined in an aliquot taken from the aqueous phase by means of its reaction with arsenazo III. Concentrations down to 4 p.p,m. may be determined at a rate of 100 samples per man-day of 8 hr.

Jan 1, 1971

By C. T. Agouridis

Head-of-hollow fills or valley fills have gained national attention due to increasing environmental concerns, particularly with regards to headwater stream loss. Researchers at the University of Kentucky in conjunction with outside scientists and consultants in the fields of stream restoration, wetland restoration, and mined land reclamation have developed new design methodologies for creating a headwater stream system for a head-of-hollow fill in eastern Kentucky. The design was largely built on the Forestry Reclamation Approach (FRA), which encourages a non-compacted spoil medium to promote tree growth, in an effort to address concerns related to water quantity and quality as well as habitat development. The major components of the design included 1) modifications to the crown geometry, 2) compaction of the crown to control infiltration, 3) utilization of natural channel design techniques, 4) use of the FRA to promote tree growth, 5) creation of ephemeral channels and vernal ponds, and 6) implementation of a novel bioreactor-wetland treatment system to improve water quality.

Jan 1, 2008

[Separates of all the Technical Publications published in 1928 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute] . METAL MINING TECHNICAL TRANS. PUBLI- TITLE AUTHOR MEETING VOLUME CATION AND PAGE* No. 50 .The Eötvös Torsion Balance D. C. Barton New York Method of Mapping Geologic Feb., 1928 Structure 52 A Cartographic Correction for the C. A. Heiland New York Eötvös Torsion Balance Feb., 1928 61. Liquid-oxygen Blasting at Chuqui- H. C. Schultz, New York camata, Chile F. K. Middleton Hunter Feb., 1928 76, 108, 123 64 Working Methods of Practical Geo- Hans Haalck New York physics Feb., 1928 65 Experiments with Eötvös Torsion P. W. George New York Balance in the Tri-State Zinc and Feb., 1928 Lead District 74 Gravity Surveying in Great Britain H. Shaw New York Feb., 1928 75 The Computation of Eötvös Gravity E. Lancaster-Jones New York Effects Feb., 1928 82 Earth-resistivity Measurements in W. 0. Hotchkiss, New York the Lake Superior Copper Country W. J. Rooney, Feb., 1928 James Fisher 83 Mining Methods and Records at the Roy W. Moore New York 76, 56, 90 United Eastern Mine Feb., 1928 98 Recent Results in Electrical Pros- Hans Lundberg New York

Jan 1, 1928

By Amalia Giannakou

This paper utilises 3-D finite-element modeling to study the static and dynamic lateral harmonic response of inclined piles, in a homogenous and a non-homogenous soil, modeled as a linear hysteretic medium. The results of a comprehensive parameter study are presented in the form of dimensionless plots of: (a) static and dynamic swaying and rocking stiffnesses and damping ratios, and (b) distribution of internal forces (bending moment, shear and axial force) with depth. These plots can be readily utilised in practical applications and they offer insight on the role of the inclination in the response of flexible piles.

Jan 1, 2006

By Lee W. Abramson

Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on several recently constructed tunnel projects. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed.

By Jean Habimana

Complex and distinct geological units spread along the 7-mile long 30-ft inside diameter Upper Rouge Tunnel CSO Control Project in Detroit, Michigan. Its construction is divided in two tunnel construction packages: The South Tunnel, to be driven in finely laminated weak TG Limy Shale, will be excavated by a shielded TBM with precast concrete segmental lining, while the North tunnel, predominantly in a relatively more competent geologic formation Antrim Shale, will be excavated by a main beam TBM with a two-pass lining system. The adits and deaeration chambers will be excavated by sequential excavation method. This paper addresses the process of selecting excavation methods and lining systems for shafts, tunnels, connecting adits, and deaeration chambers.

By Lenin Salazar Dulanto

La baja de precios en algunos minerales ha obiligado que las empresas mejoren su proceso productivo a través del uso de equipos de última tecnología en los procesos de mecánica, hidráulica, electricidad y electrónica, así como en la eficiencia en el corte y taladrado, extracción y transporte. Sin embargo, tanto el desatado y sostenimiento manual desarrollaron un estréss y desgaste de energía en el trabajador. En este sentido, el presente trabajo señala una nueva forma de realizar tales operaciones en el ciclo de minado de la empresa Milpo a fin de garantizar la seguridad física de los trabajadores y equipos.

Jul 31, 2003

By R. M. Spang

Abstract Between the German city of Dresden and the Czech capital Prague a 4-lane highway is under con-struction. At the outskirts of Dresden it will cross the narrow and deeply eroded Weißeritz Valley by a bridge. Two twin tube tunnels under oblique angles join the bridge out of the rocky valley flanks. The different geotechnical conditions of these 4 tunnel portals, their design and construction are described within this publication. The two southern portals of the tunnel Dölzschen are situated within a vertical 65 m high former quarry slope, 25 m above the valley floor. The slope proved instable due to toppling failure and exposed serious rockfall risks. Systematic anchoring, scaling, rock bolting, netting and filling under extreme access conditions eliminated these risks. Tunnel excavation started from the slope surface without any pre-cut or conventional portal construction. The opposite northern portals of the tunnel Coschütz are situated in more gentle rock slopes. After removal of debris, excavation of the eastern tunnel started in a 30° slope striking oblique to the driving direction, without any precut, too. Because of the gentle slope inclination the cross section was not earlier completely covered by rock than 30 m behind. The western tunnel started from an optimized short, narrow and steep precut. Its flanks were stabilized by reinforced shotcrete and rock bolts. Because of the small distance between the tubes rock bolts were drilled into the cross section of the neighboring tunnel. Tunnel excavation was made by drill and blast operation, preliminary support consisted of steel arches, reinforced shotcrete and radial rock bolts. Thorough survey of the bolt’s coordinates and direction prevented them from meeting each other. Rock bolts were of the permanent type to prevent the final lining from being obliquely loaded. Systematically arrayed measuring devices checked deformations of slopes and tunnels. Zusammenfassung Der Neubau der Bundesautobahn A 17 wird Dresden und Prag miteinander verbinden. Die vierspurige Autobahn quert westlich von Dresden das enge und tief eingeschnittene Tal der Wilden Weißeritz mit einer Brücke. An beide Brückenwiderlager schließen mit schiefwinkligem Anschnitt doppelröhrige Tunnel an, deren Portale in den felsigen Talflanken liegen. Die unterschiedlichen geotechnischen Verhältnisse, die Überlegungen für einen jeweils optimalen Entwurf und der Bau der portalnahen bergmännischen Tunnelabschnitte sind Gegenstand dieser Veröffentlichung. Die Südportale des Tunnels Dölzschen liegen in einer vertikalen, 65 m hohen Felswand, 25 m über dem Talgrund. Die Felswand erwies sich als global kippgefährdet, außerdem lagen flächig verteilte erhebliche Steinschlag- und Felssturzrisiken für Bau und Betrieb vor. Die Kippgefahr wurde durch ein Systemraster aus vorgespannten Felsankern, die Steinschlag- und Felssturzrisiken durch bergsteigerisches Beräumen mit dem Brecheisen, Felsnägel und Steinschlagschutznetze eliminiert. Der Tunnelausbruch begann von einer Vorschüttung direkt in der Felswand ohne Voreinschnitt im Schutz einer kurzen Luftbogenstrecke. Die gegenüberliegenden Nordportale des Tunnels Coschütz befinden sich in wesentlich flacheren Hängen. Nach dem Aushub einer mehrere Meter dicken Abraumhalde begann der Tunnelausbruch der östlichen Röhre asymmetrisch mit einer Luftbogenstrecke in einer spitzwinklig zur Vortriebsrichtung streichenden, 30° mit dem Vortrieb steigenden Felsfläche, ebenfalls ohne Voreinschnitt. Wegen der flachen Neigung der Böschung war der Tunnelquerschnitt erst nach 30 m vollständig überdeckt. Für den Vortrieb der westlichen Tunnelröhre mussten erst eine zwischen den Röhren vorhandene Felsnase teilweise abgetragen, die westlich anschließende zurückspringende Felswand vertikal gestellt und gesichert und Felsaushub in der rechten Flanke getätigt werden. Der damit entstehende Voreinschnitt wurde so kurz wie möglich und ohne seitliche Arbeitsräume ausgeführt. Die Sicherung der Böschungen erfolgte mit bewehrtem Spritzbeton und Felsnägeln. Wegen des geringen Abstands der beiden Röhren wurden die unteren Lagen der radialen Ausbruchsicherung durchgeankert. Der Tunnelvortrieb begann im Schutz eines geankerten Portalkranzes und ebenfalls von einer Luftbogenstrecke aus.

Jan 1, 2003

By W. R. Crank

[Rock bursts are phenomena associated with mining operations, particularly with deep mining, although they occur throughout a wide rump, of depth, from 600 feel downward. The intensity is usually in direct proportion to the depth, varying from a loosening and sloughing off to a violent rupture, giving rise to the term, "explosive rock." The more or less violent breaking of rock in mine working, tins been variously designated as " flaking," "pressure hoists," "strain bursts," "bumps," "quakes," and "air blasts," which indicate opinions as to cause and effect. The term "air blast" lots probably beat most widely used, and naturally so, as a more or less rapid movement of air often accompanying the more violent phenomena of rock failure. Furthermore, there is an implied if not definitely expressed degree of magnitude in the action designited by a given term and in the cause and character of the action. For example. flaking, pressure bursts, and quakes are terms ranged to indicate action of increasing magnitude; and pressure bursts, strain bursts. bumps, and quakes are ranged according to the cause and character of the action.]

Jan 1, 1929

By C. Hellar

A new dual-boom remotely controlled roof bolter was designed, fabricated, and then tested in an underground coal mine. Remote-control functions allowed complete bolting cycles to be performed on two booms with both operators located within protective cabs. Capabilities included 3-to 6-foot-long bolts in 5-to 8-foot seams, limited to bolts 20 inches shorter than seam height. Machine was in compliance with all regulations including dust collection, machine lighting, and permissibility.

Jan 1, 1979

By Joseph N. Bakambu

It is currently recognized by mining society that autonomously guided underground mining vehicles may greatly increase the efficiency of mining production and improve human safety. Recent results in mobile robotics, data fusion and sensor development provide a solid basis for solving the problems related to autonomous underground navigation. Recently developed commercial systems mostly rely on the infrastructure that is expensive and difficult to maintain. Guideless navigation in unstructured and harsh environment of underground mines is still a challenging task. In this paper, we describe an autonomous navigation system for an underground mining vehicle equipped with on-board dead reckoning, inertial and optical sensors. This system does not require any artificial infrastructure and is capable to guide the vehicle along the complex environment of interconnected underground drifts; it also ensures the detection of obstacles on the vehicle path. The user interface for monitoring and control is described and the results of laboratory tests and on-site experiments are presented. Work in progress addresses the system integration for real equipment, and the system upgrade, adding map-building and selflocalization capabilities .

May 1, 2002

By R. D. Peterson

As underground mine operations expand, the ventilation systems supporting them become complex. Complexity increases with periodic ventilation changes. New diagonal connections require a rebalance of resistance to maintain airflow in affected splits in the system. Incidents of mine fires and explosions have occurred in U.S. coal mines when diagonal connections resulting from ventilation changes have resulted in changing airflow directions. MSHA regulations prohibit the reversal of airflow and poor ventilation practice in general, but regulations cannot stipulate or recommend proactive preventative measures because every situation is different. This paper discusses the phenomenon of diagonal branches and recommends practical precautionary measures that can be taken to prevent airflow reversal in planned ventilation changes.

Jan 1, 2012

By Gabriel S. Esterhuizen, Anthony T. Iannacchione

The roof rock in underground limestone mines in Northern Appalachia can be subject to high horizontal stresses in spite of the shallow depth of the workings. The high stresses can cause roof stability problems. The National Institute for Occupational Safety and Health staff have observed a distinctive asymmetrical mode of failure at the pillar-roof contact in two underground stone mines, which is different from the typical failure mode observed in response to excessive levels of horizontal stress. A dip of greater than 5° was identified as a possible cause of this mode of failure. Numerical model experiments showed that an increase in the dip of the workings can cause an increase in the stress at the up-dip corner of the roof beam. A case study is presented in which failure at the pillar-roof contact was observed where the dip of the workings was 7° in a high horizontal stress field. Numerical modeling showed that the relatively small dip of the workings could have induced stresses changes in the immediate roof that would explain the failures. The model results also showed that this mode of failure is less likely to occur if the limestone pillars contain weak bedding planes that provide stress relief. In addition, the results showed that for the conditions at the case study site, the stress in the roof beam was not sensitive to the thickness of the roof beam or to the excavation span. The high horizontal stresses at this site are an important contributing factor to the observed failures.

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

Provide an unobstructive means of measuring small changes in distance from roof to floor or from rib to rib of a mine opening and the rate of closure in order to help operators of under-ground mines detect hazardous ground conditions. Approach A small ultrasonic measurement system was developed to detect g round movement and define closure rates. How the System Works The system contains two parts: a transducer and a readout device. The small ultrasonic transducer, similar to an audio speaker diaphram, is plucked with an ultrasonic frequency every six seconds. This frequency wave is sent through the air and reflected back to the transducer off any surface at which the transducer is pointed. The amount of time needed by the ultrasonic wave to make this round trip is accurately measured using a precise oscillator / timer and is converted into a measure of distance. The accurate 6-second time interval is used to convert any subsequent changes in the reading to a rate of change in feet per minute. Two readings are then displayed alternately on the readout instrument.

Jan 1, 1984

By Robert L. de Beauchamp

The Bureau of Mines designed a chlorination apparatus to prepare CrCl2 free of CrCl3 by the direct reaction of chlorine and chromium. Equipment and procedures were developed for routine preparation of 25-pound batch quantities of anhydrous CrCl2. Calcium, iron, nickel, and silicon impurities were in the 0.01 to 0.05 percent range, and all other impurities were below 0.01 percent.

Jan 1, 1968