Search Documents

By S. R. Zimmerley

As a result of the drilling program of the Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

? Founded In 1953 ? Mining growth of 83% since 2007 ? We produced over 1 million ounces of Au in 2012 ? We Forecast of 20% Au production in 2013-2015 ? We have paid a dividend 31 years consecutively. Terry Reid ? 1992-93 Electrical Technical, College ? 1994-95 On the job placement College ? 1998 ? Licensed Millwright, ? 2005-12 ? Maintenance Reliability Planner ? 2012- Present Business Process Owner

Aug 1, 2013

By James E. Maccariella

Replacement of an existing movable bridge with a new low level fixed bridge would not accommodate potential future navigation traffic. In order to replace the existing bridge in a cost effective manner, while accommodating the potential future needs of the Port of Salem, a new bridge was proposed that would permit conversion to a vertical lift type movable bridge should a potential need for upstream navigation warrant such a project in the future. Drilled shafts were found to be the most desirable foundation type for the replacement of the Route 49 Bridge over Salem River. Their ability to resist scour, be constructed without cofferdams, adequately resist vessel collision forces, and accommodate conversion to a future vertical lift bridge allowed the project to meet both the needs of the New Jersey Department of Transportation and the Port of Salem.

Jan 1, 2005

By J Webster-Brown

The Tui Mine is an abandoned Pb-Zn mine giving rise to water quality problems in the Te Aroha region of Coromandel, New Zealand. When sampled in September 2002, for example, both the Tui and Tunakohoia Streams draining the mine site exceeded ANZECC (2000) water quality guidelines for aquatic life protection (Cu, Cd and Zn) and recreational quality (Cd). Based on trace metal mass flux (kg/yr) from parts of the mine site, the principal pathways by which Cu, Zn and Cd contamination reach these streams have been identified as:the tailings dam leachate,the diverted stream water from above the dam,the drainage from Adit 5 (which accounts for 95 % of Zn and Cd contamination in Tunakohoia Stream), andto a lesser extent, run-off from waste rock piles below Adit 4 level. Of the various remediation options, which have been proposed for the site, the following are identified as providing the best protection for the Tui and Tunakohoia streams:stabilising the tailings dam embankment and capping the embankment and tailings,constructing and/or cleaning out engineered diversion drains around the perimeter of the tailings dam to divert surface water away from the tailings dam, andinstalling bulkheads within Adit 5. A formal postal survey of the people of Te Aroha (66 respondents from 230 surveys) indicated that their priority was that the site be made safe for the public to visit, and used for recreation. As soil samples in potential recreational areas of the mine site, significantly exceeded guideline values for Cu, Pb, Zn, Cd and As, soil removal or capping clearly also needs to be part of a remediation plan. Development of the site as a historical/ecotourism area was viewed favourably, as this may encourage more visitors to the Te Aroha area as well as educate local residents.

Jan 1, 2003

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

By K Niyomjinda, B Etschmann

Chatree Gold Mine is currently the only modern day gold mine operating in Thailand, and is situated approximately equidistant from Chiang Mai in the north and Bangkok in the south. Environmental guidelines set by the Thai authorities require Chatree Gold Mine to achieve a Total Cyanide level of 20 ppm or less in the process plant discharge slurry stream prior to release into the tailings storage facility. This paper describes both the initial difficulties faced in achieving compliance on this limit utilising the conventional INCO SO2/Air cyanide destruction system and the subsequent process improvements initiated to both the leaching process and the standard INCO process to achieve the current compliance levels of approximately 99/100 shifts. Improvements were focussed on the dual aspects of reducing the formation of WAD cyanide and ferrocyanide species in the leaching circuit coupled with process changes to improve removal of the ferrocyanide species from solution during the cyanide reduction stage.

Jan 1, 2004

By John J. Murray, Michael T. McRae, Michael A. Krulc, Kathy L. Schuler

The San Vicente Pipeline Tunnel Project involves the construction of an 8.5-foot-diameter water pipeline in an 11 mile tunnel in San Diego, California. The tunnel is located in extremely variable geologic conditions of strong granitic and volcanic rocks, weak sedimentary rocks, abrasive conglomerates, and mixed face conditions. One reach of the tunnel is a 5,200-foot mixed face reach that includes Friars Formation Conglomerate overlying granitic rock. Due to the variable ground conditions in this reach, the use of a TBM was deemed too risky and the contract documents required drill-and-blast and hand mining methods. Although it was not required, the contractor elected to construct this reach using NATM methods. This paper describes the geology of the 5,200-foot mixed-face reach, the design evaluation, and the construction challenges faced on this project.

Jan 1, 2007

By David A. Larson

Preliminary laboratory experiments have been conducted by the Bureau of Mines to define the influence of bit geometry on methane ignitions as a step toward establishing safer mining-machine operating parameters. The experimental system was designed to simulate the operation of a continuous mining machine, using a drum-type cutterhead of normal diameter with a narrow cross section, permitting full-diameter drum cutting tests to be run on material representative of sandstone lenses (or inclusions) in coal seams. Two conical bit types were tested at shallow depths of cut with three drum speeds. Bits that rotated in the mounting block during testing did not produce ignitions. The ignition frequency for used bits was three to four times greater than for new bits at the same kerf depth.

Jan 1, 1983

By John E. Wiegand

This study will discuss the AMAX Coal Co., Penndiana Pipeline Project, which was conducted in conjunction with the following parties: AMAX Coal Industries, (U.S.B.O.M.) United States Bureau of Mines, (I.D.O.R.) Indiana Division of Reclamation, Ohio Valley Pipeline, Inc., New Mexico Tech, and ourselves, VIBRONICS, INC., Evansville, Indiana. The purpose of this study was to find a safe vibration level for active gas transmission pipelines near surface coal operations.

Jan 1, 1994

By C A. Feebrey, R A. Duncan

The Ebor Volcano in north eastern New South Wales is an eroded example of a central-type intraplate volcanic-intrusive complex. It is of Miocene age (19 - 20 Ma) and has similarities to other central-type volcanoes in eastern Australia which may represent manifestations of sub-lithospheric hotspot activity. Thick lava flows are exposed around the Great Escarpment and are dominated by a tholeiitic basaltic suite, ranging from ol-tholeiite to qz-tholeiite to icelandite with ages of 19.2 - 19.6 Ma. On its western edge, the tholeiitic lava suite probably overlies remnants of basanite flows belonging to the Eocene (~48 Ma) Doughboy province, but elsewhere, minor alkaline basaltic lavas may be coeval with the tholeiitic suite. Several felsic bodies were emplaced into the volcano at ~19.0 - 19.2 Ma and include subalkaline and peralkaline types. The Crescent Complex is a Miocene-age, strongly differentiated mafic to felsic intrusion in basement rocks and centrally located in pre-erosion reconstructions of the Ebor Volcano. It is interpreted to be a major feeder for the tholeiitic lavas based on age and composition. Evolution of the dominant tholeiitic suite proceeded from a parental ol-tholeiite magma, through qz-tholeiite, icelandite and small volumes of felsic rocks by fractionation of plagioclase, olivine, clinopyroxene and titanomagnetite, accompanied by enrichmentof SiO2, SFeOlMgO, alkalies and HFSE.

Jan 1, 1995

By M K. de Brodtkorb

Late Cenozoic ore deposits æPrecious and base metal-richÆ and æSn-Ag-polymetallicÆ ofNorthern Puna are associated either with Middle Miocene dacitic volcanic-dome complexes or with Upper Miocene dacitic-andesitic volcanic centres.   Ore mineralogies and their related volcanism are discussed. A strong link is observed between the Cenozoic Metallogenetic Province of Northern Puna and the Southern Bolivia Tin and polymetallic provinces.  

Jan 1, 1995

By Brian P. Waagner

Construction law in general and the law of deep foundations in particular continues to develop rapidly, particularly in the areas of risk allocation. Public and private owners are increasingly using contractual disclaimers to shift the risk of differing site conditions to contractors, and courts are increasingly willing to enforce these contractual devices. Perhaps also in an effort to control costs, public and private owners are turning to design-build contracting techniques. While design-build offers many advantages over traditional project delivery systems, it does not answer all of the risk-allocation questions that frequently arise. Even in design-build, problems with unanticipated subsurface conditions and defective design are not easily addressed. Finally, developments in electronic commerce present the potential to transform the construction industry.

Jan 1, 2002

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude run to stills. Furthermore, the premise the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By E. D. Calvert

The room temperature tensile properties of commercially pure titanium and seven titanium alloys prepared by skull casting were determined in the as-cast and heat-treated conditions. Data were compared with property data from tensile tests on wrought alloys of the same compositions in the as-worked and heat-treated conditions. The alloys evaluated were Ti-5Al-2.5Sn, Ti-6Al-4V, Ti-6Al-4V-lSi, Ti-6A1-2Sn-4Zr-2Mo, Ti-6A1-6V-4Zr-4Mo, Ti-6A1-6V-2Sn, and Ti-11.5Mo-6Zr-4.5Sn. Test specimens were prepared from both static and centrifugal castings and from plate fabricated by forging and rolling vacuum-melted ingots. The data indicate that the alpha and alpha-beta alloys have strength properties in the as-cast condition that are reasonably close to the strength properties of their wrought counterparts in the as-worked condition. An exception to this was the Ti-6A1-6V-4Zr-4Mo alloy for which insufficient data were available to form any firm conclusions. Fine-grained cast structures of Beta III (Ti-11.5Mo-6Zr-4.5Sn) were shown to be generally stronger in the as-cast condition than the wrought alloy in the as-worked condition except for the yield strength of one structure that was unusually low. Heat treatment of this alloy produced properties that were unpredictable. Indications are, however, that optimization of heat treatment parameters for each cast structure could produce strength properties equal to that of wrought materials.

Jan 1, 1974

By L Baumgardner, A. V. Castelli

Barite In 1987, United States mine production of barite increased 15.870, consumption (sold or used by grinding plants) increased by 6.97, and imports are estimated to have fallen by 19.57. World mine production decreased by 137, according to the US Bureau of Mines. The value of US produced barite, fob mine, decreased 1.4%, according to the Bureau. The declared value for cif US port of all imported unground barite during the first 10 months of 1987 decreased from $39.02/t ($35.40 per st) to $37.16/t ($33.71 per st), the Bureau stated. Nevada continued to be the leading US producer of' barite with 637r of the total. It is followed by Georgia, Missouri, California, Tennessee, and Montana. The Bureau of Mines estimates 657 of the US mine production was used as a weighting agent in drilling fluids. The remaining 35°/r was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the non-oilfield sector. This sector continued to increase. Of the total consumption (used by grinding plants and chemical manufacturers), it is estimated that 8070 was used in drilling fluids and 2017( in the non-oilfield sector - barium chemicals and fillers in paper, plastics, and glass. The tonnage consumed in the drilling fluids market increased slightly. But the average number of rotary rigs operating decreased from 964 in 1986 to 936 in 1987. This is the lowest number of operating rigs reported since 1949. The increase in consumption in this sector is due to an increase of rigs operating in the US Gulf and other higher consumption areas over 1986. Crude barite imports were estimated to be down by 19.5% in 1987. Still, they accounted for 637 of the barite consumed in the US. During the first 10 months, China continued to be the leading exporter to the US with 86.970, followed by Mexico with 10.997, and Morocco 2.107(. About 5Y of the imported ore was used in the nonoilfield sector. Ground barite imports dropped from 19.8 kt to 8.8 kt (21,800 st to 9800 st) in 1987. Of this amount, 1.4 kt (1598 st) was used in drilling muds and the remainder of the non-oilfield use. During 1987, a few more grinding plants that supplied the drilling fluid market were closed. Along the US Gulf Coast, there are 13 operating plants versus a high of 31 in 1981. Cameron Offshore reopened its grinding plant at Cameron, LA. New Riverside Ochre Co. of Cartersville, GA, purchased a jigging-washing plant in Missouri and plans to place it in operation this year on a new deposit near Cartersville, GA. Milpark purchased Hughes Drilling Fluid in 1987 and operates under Milpark. US mine production will probably stay about the same as 1987. Price increases in the 10 % range for imported ore are expected due to water freight and the weak dollar. Baker Hughes estimates the average number of operating rotary rigs at 1070. A slight increase is expected in the non-drilling fluid market (chemicals, glass, and filler). Bauxite and alumina L. Baumgardner, US Bureau of Mines Domestic bauxite production in 1987, expressed as dried equivalent, was 581 kt (640,400 st), a 14% increase over 1986. US mine production amounted to less than 170 of total world production. Virtually none of the domestic bauxite was consumed in the production of primary alumina metal. About 30% of the bauxite produced by US mines was calcined to produce 117 kt (128,970 st) for use in abrasives, catalysts, chemicals, proppants, and refractories. Most of the uncalcined bauxite was refined to specialty aluminum oxide (alumina) forms. Metallurgical grade bauxite was imported from 10 countries in 1987. Principal suppliers of the 9.8 Mt (10.8 million st) were Guinea (4270), Jamaica (3501,), Australia (127), and Brazil (57). The average value, delivered U.S. ports, cif, as reported to US Customs Service, was $29.50/t ($26.76 per st). Calcined refractory grade baux-

Jan 6, 1988

Jan 1, 1987

By Gregory J. Canivan

Three test pile programs were conducted in Charleston, South Carolina to evaluate differences in bearing resistance due to installation methods. The tested piles were installed with impact hammers and vibratory drivers through soft clays and/or loose sands into the Cooper Marl, a stiff calcareous marine clay or silt. Piles driven into the Cooper Marl experience significant capacity gain with time following initial installation due largely to pore pressure dissipation. Pile size and pile type were both known to affect pore pressure generation during installation and subsequently the capacity gain with time. The test programs were primarily conducted to optimize pile design values and construction methods with regard to trestle construction but the results also contribute to the understanding of driven pile behavior. High strain dynamic testing was performed on several open-end pipe and H-piles. The measured difference in long-term bearing capacity of the H-piles as a result of the two installation methods was negligible, while the short-term bearing capacity of the pipe pile was larger when the piles were installed using impact hammers. The lower short-term resistance in the vibratory driven piles is attributed to larger excess pore pressures generated during installation compared to those generated during impact driving.

Jan 1, 2002

This Bureau of Mines publication contains five papers pertaining to the effective grounding of mine power systems, as follows: Ground-check monitor types and safety characteristics; ground wire monitors for surface coal mines; ground bed design and measurement; electrical ground rod corrosion; and a continuous ground bed resistance monitor.

Jan 1, 1979

By R. K. Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a cascading pillar failure, occurs when one pillar in the mine layout fails, transferring its load to neighbouring pillars and causing them to fail in succession. Recent examples of this kind of failure in coal, metal and non-metal mines in the USA are documented. Mining engineers can limit the danger presented by these failures through improved design practice. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This is used as a basis for three design approaches to control cascading pillar failure: containment with barrier pillars during pillar splitting; prevention with panel pillars of high width-to-height ratio and small-centre mining; and full extraction by retreat mining

Jun 19, 1905