Search Documents

By Louis J. Mittoni

"It is well known that gas injection systems can exhibit a wide range of dynamical behaviours, ranging from linear periodic bubbling through to highly complex turbulent jetting. Recently, it has been observed that an important intermediate regime exists under certain system conditions, where the dynamics are complex in nature yet predictable for short time periods. This paper reviews the evidence to support the above hypothesis, and discusses the invariant quantitative measures such as density, return maps, Lyapunov exponent and dimension which may be used as pattern recognition features in a mOnitoring and control strategy.INTRODUCTIONThere has been a great deal of research on the submerged injection of gases into liquids. This interest is primarily due to the large number of applications in the pyrometallurgical and chemical engineering industries. Gases are typically injected into liquids to achieve goals such as heat and mass transfer, or physical mixing and agitation. Only recently though has the possibility of using the evolution of the gas dynamics as a probe to internal system conditions been raised [1, 2].At very low gas injection rates and small upstream chamber volumes, gas normally disperses in the form of stable bubbles of constant volume [3]. With increases in gas flow rate, the dynamics become more complex, bifurcating into double bubbling, multiple bubbling and complex coalescence behaviour. Irregularities measured in pressuretime series acquired upstream of the injection port under these complex conditions have usually been treated as bothersome noise or contamination to be filtered from the signal and ignored in the analysis. These irregularities, however, may contain physically interesting and useful information on the system from which they were produced if the system may be classified as deterministically chaotic [4]."

Jan 1, 1996

By M. K. Rizkalla

This paper discusses the time-dependent behaviour of rock when it involves the presence of several layers of rock strata in the vicinity of mine openings, mining in sequences and the placement of backfill. The paper describes numerical techniques which proved useful when such situations are encountered in practice. The model is elastoviscoplastic. At given time stations, short term loading or changes can be made to the creep behavior of the rock. The modelling technique is first described and is followed by simulations of stresses and displacements in a potash mine with the primary objective to demonstrate the effect of such aspects as mining and fill sequences in 3-D. This involves cutting finite elements representing the strip of the mining face and simultaneously filling those elements representing the newly placed fill. The stiffness of the fill varies with the degree of compaction at each point. In this way, the effect of the time of fill placement, the gap between the top of the fill and the back as well as the degree of compaction are simulated. The second example is a 2-D problem simulating the long term effect of backfill, as a material compacting with time, on the settlement of the layers above it as well as the closure of the room.

Jan 1, 1996

By Brabcova Z.

This contribution deals with bubble adhesion on particle surface which consists of three steps ? the liquid film thinning, the film rupture and expansion of the three phase contact (TPC). Our attention is devoted to the third step ? to the description of the TPC expansion. Three-phase contact line expansion can be theoretically described using hydrodynamic and molecular-kinetic models. Both of these models were originally developed for the interaction of the bubble with horizontal plane in pure water. Our experiments deal mainly with the interaction of the bubble with the inclined plane in the solution of surface active agents. It was proved experimentally that molecular-kinetic model corresponds also to these conditions and this model was used for the description of the TPC expansion. The model is based on the theoretical description of the bubble contact angle on the three-phase interface. These contact angles change dramatically from 180o to equilibium (Young) contact angle close to 90o. Modificated ADSA method is used for the calculation of the contact angle. This method utilizes the Laplace equation of the capillarity; the bubble profile and the contact angle are evaluated using the set of experimental points around the edge of the bubble. The comparison of the experimental and calculated bubble profile shows a good agreement. The aim of the project is to describe the process of the TPC expansion during the adhesion of the bubble with the diameter up to 1 mm. Inclined planes were used instead of an experimental solid particle. Our experiments were provided in the solution of surface active compounds. The process of the adhesion was recorded using high-speed digital camera and images were evaluated using the image analysis software NIS-Elements. Calculations were performed using the MATLAB software. Keywords: bubble-particle interaction, adhesion, three-phase contact, contact angle

Sep 1, 2012

By E. Isokangas

The production of minerals for economic use is a two-stage process, involving mining to extract the mineral from the ground, and processing to convert the mineral into a marketable product. Generally, mining and processing have been viewed as self-contained entities. Both have separate objectives, separate cost centres and key performance indicators (KPIs) that do not reflect the customer/supplier relationships that inherently exist. However, mining and processing operations are inter-connected and therefore intimately inter-related with the performance of one operation affecting the performance of another. Optimizing each stage separately without considering the whole system often misses potential economic benefits and energy savings. During the past fifteen years, the authors have been involved in implementing a holistic methodology ?Mine to Mill Process Integration and Optimisation (Mine to Mill PIO)? to maximize the overall profitability of the operation rather than just optimizing any individual process in a mining operation. Metso Process Technology and Innovation (PTI), along with their project partners, have conducted several projects to significantly increase their production- generating typically 5% to 20% higher throughput and improve the overall mine and concentrator performance through PIO methodology. This proven methodology has applications ranging from greenfield projects to long-standing operations with AG/SAG, HPGR or conventional grinding circuits. This paper explains the Mine to Mill PIO methodology and discusses the benefits of such an approach on the energy consumption, the overall costs and benefits of mining operations. The paper also summarizes several case studies illustrating the use of PTI methodology in a variety of applications. Keywords: integration, optimization, simulation, modeling, mine-to-mill, comminution, blast, drill, crushing, grinding

Sep 1, 2012

By W. L. Dare

This information circular is one of a series, published by the Federal Bureau of Mines, on methods and costs of mining uranium ore on the Colorado Plateau. This report describes the relatively small-scale operations of the Salt Wash miner: The mining method followed, the equipment used, and the production costs. It describes 10 lease-operated mines of Union Carbide: Nuclear Co. that are typical of Salt Wash operations on the plateau. These mines lie within the Uravan mineral belt3/ and arc in the Gateway, Bull Canyon, and Uravan mining districts. (See fig. 1.) Generally the ore bodies occur as irregular, discontinuous layers of ore minerals within sandstone beds in the Salt Wash member of the Jurassic Morrison formation. The ore bodies sometimes occur as rolls, pod associat with carbonaceous trash, or tabular masses. Their size and erratic distribution preclude the use of a prearranged and uniform stoping system. The mining method is simply to follow the ore and leave open scopes behind.

Jan 1, 1959

The dynamic breakage process of rocks by the impact of a hydraulic hammer is more complex than one normally assumes. It is even more difficult when one has to conduct the breakage under water. In such cases one does not know exactly what the surface topography and composition are at the bottom of the sea or river and, hence, it is more difficult to select the best position of the hammer before starting the hammering. Typically, an industrial hammer has a diameter of about 250 mm, a length of about 1.25 to 1.75 m and a mass of several tons. The hammer frequency can be up to 50 impacts per minute. The general principles of rock hammering can be easily summarized, but this knowledge is not sufficient to adapt adequately the method for less common rock conditions (e.g. less brittle rock, presence of vertical and subvertical fractures, etc.). That is the reason why we initiated a research project, whereby a scale model has been developed to conduct experiments in the laboratory and whereby discrete element simulations are being conducted. Both aim at a better understanding of the basic mechanisms of rock hammering. The scaled experimental model allows varying the impact energy and the static weight independently. Within the experiment, the hammer is in contact with the rock specimen under a certain confining pressure and with a certain contact pressure due to the static weight. A weight falls on the hammer, creating the dynamic action or impact; the height over which the weight falls can be varied. The penetration is recorded after each impact. After a certain penetration the test is stopped and the internal crack patterns are described. Some simulations have been conducted, allowing the modeling of individual fracture initiation and growth during the penetration of the hammer by either a constant displacement rate (using the UDEC-code) or by introducing the dynamic process (using the PFC-code). Some of the observed features in the laboratory experiments can be visualized in the simulations. However, further research is needed to allow the simulations being an adequate tool to well understand the dynamic process in laboratory experiments, as well as the in-situ behavior.

Aug 1, 2013

By T. Gupta, T. Ghosh

"Rare Earth Elements (REEs) and their compounds are essential for numerous modern high tech applications such as renewable energy technologies, catalysts and defense applications. The destabilization of REE pricing owing to the global demand and supply deficit has forced many countries to re-evaluate the possibility of indigenous production of REEs. Cost effective and eco-friendly opportunities are being widely explored for extraction of REEs from non-conventional mineral sources such as coal and coal byproducts to stabilize the supply chain. Coal from Central Alaska (Healy Coal Mine) and Southern Alaska-Cook Inlet (Wishbone Hill) province have been found to possess elevated REE concentrations as compared to average world coal estimates. The objective of the study is to enrich the REEs in the fine size fraction (-75 Microns) from Healy and Wishbone Hill by froth flotation technique. A Box-Behnken design was applied for modeling and optimization of some operating variables on the flotation to maximize REE enrichment. The variables studies were frother dosage, pulp density (% Solids) and collector dosage. Experiments were carried out using a statistical design and the main and interaction effects on response variable was evaluated by analyzing 3D response surfaces. Based on the experimental results the optimum flotation conditions for maximum REE enrichment in the froth fraction was obtained at 4.2% Solids and 32.7 ppm of frother dosage for Healy coal sample and 10% Solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic equation for modelling and optimizing the response variable is found to be independent of collector dosage for both the coal samples. INTRODUCTION Alaskan coal deposits are distributed in three major coal provinces and are in Cretaceous and Tertiary rocks. The climate, vegetation type and sedimentation process has attributed to low sulfur content (averaging 0.3 percent) in Alaskan coals compared to other coal deposits found across the globe. In Central Alaska-Nenana and Southern Alaska-Cook Inlet coal province coal resources are contained in Tertiary rocks while bulk of the Coal resource in North Slope coal province is contained in Cretaceous and Tertiary coal bearing rocks [1]. Coals from Central Alaska- Nenana (Healy) and Southern Alaska-Cook Inlet province (Wishbone Hill) have been found to possess elevated concentrations of critical REEs as compared to the amounts present in world coals (Figure 1). The Wishbone Hill deposit is considered a relatively small deposit, with about 14 million tons of identified reserves, compared to Healy which has over 500 million tons identified [2]. The REE concentrations up to 286 ppm and 524 ppm on ash basis have been reported by Gupta et al. in 2016 with elevated concentrations Ce, La, Y and Nd which are expressed to be of critical importance by US Department of Energy. Accordingly, the two coal samples possess the potential to be used as a REE resource in the near future under favorable socio-economic and geo-political scenarios. [3, 4]"

Jan 1, 2017

By S. Chander

The effect of sample storage in argon and in air on kinetics of oxidation of pyrite from a coal source was studied using accelerated weathering test in laboratory columns. Prior to the weathering tests the samples were crushed, ground, and stored for various time periods in argon and air. The results showed a dramatic difference in the rate of oxidation of the aged samples. The differences were interpreted based on the hypothesis that the aging of pyrite led to the formation of surface coatings which changed with time. The significance of these results in pyrite/reagent interactions in flotation and in evaluating the acid mine drainage potential of pyritic waste materials is discussed.

Jan 1, 1993

By E. Asselin

Passivation of Fe-Ni-Co alloys during the Caron leach process is thought to result in low cobalt recoveries in ammoniacal ammonium carbonate solutions. A brief review of the available thermochemical data for the (Fe, Ni, Co)-NH3-H2O systems has been undertaken. The stability of the Co(II) and Co(III), Ni(II) and Fe(II) am-mines was examined through the use of speciation and Pourbaix diagrams at 298 and 333 K and at 6 M total ammonia. Increasing the temperature reduces the stability fields of the ammines and generally constrains the thermodynamic window for the leach. The Fe(II) ammines are only thermodynamically stable under reducing conditions. Polarization experiments show that these ammines are unlikely to form if oxygen is present. Fe-Ni-Co alloy passivation may be alleviated by careful management of potential.

Jan 1, 2011

By C. O. Stee

Introduction The property of Siscoe Gold Mines, Limited, is located on an island of three hundred and forty acres in lake Kienawisik, about fifty-two miles east of Noranda and forty-three miles south of Amos, Quebec. Lake Kienawisik is a part of the Harricanaw drainage system and is crossed by the main line of the Canadian National railway at Amos. This waterway is navigable for boats with a draught of six to eight feet. Diesel engines have been the source of power at the property since milling operations were commenced in January, 1929. The power plant as first designed and built was for a milling capacity of 100 tons. Two Polar-Atlas units, each of 200 h. p., comprised the original installation. With the growth of the 'mine, more engines were added until, at the present time, there is installed at the Siscoe what is rated the largest Diesel plant at any mining property in Canada. Definition of a Diesel 'The Diesel engine is an internal combustion engine which works with liquid fuel introduced after, and independently of, the air charge at a time when communication between the cylinder and the outside atmosphere is cut off, and which ignites the fuel by compression-beat and stored combustion-heat unassisted by heat sources outside the cylinder itself while the engine is in stable operating condition"(1).

Jan 1, 1934

By Da-Rong Chou

An optimum method for selecting exploratory drilling locations has been developed. The process has been modelled as a highly non-linear programming problem subject to constraints. Solution involves an iterative algorithm which converges rapidly and procedures have been developed to distinguish between local and global optima. The algorithm has been implemented as an interactive computer program which allows the user to influence directly the solution process and to evaluate the effect of any manual adjustments to the optimal solution.

Jan 1, 1984

By Bernard Lewis

The ignition problem: for a layer of firedamp bordering on a cloud of detonation products is evidently considerably more complicated than in the usual laboratory ignition experiments, in which a well-defined volume of gas is heated and the occurrence of ignition is observed after an induction period. An atmosphere of firedamp exposed to the detonation of a high explosive is subjected to heating by shock-wave compression and thermal conduction and to intermixing at the interface of the firedamp atmosphere and the cloud of deto¬nation products. Although a reliable physical-chemical analysis of the problem is not yet possible, one may nevertheless form a general view of the role of compression waves and the processes of heat transfer and diffusion at the interface. Near the mouth of a shot hole, or near a freely suspended cartridge, the firedamp atmosphere attains very high temperatures by adiabatic compression, and it is certain that such temperatures are sufficient to initiate chemical reaction. The pressure wave pattern is reproducible from one test charge to another if the initial experimental conditions are held constant; on the other hand, experiments on firedamp ignition do not yield a reproducible threshold condition for ignition, but only an ignition probability. Thus, the induction periods are sufficiently long that there is time for the compressed', heated gas layers to undergo random changes that may quench or promote ignition. Therefore, the analysis of the ignition problem hinges primarily on the discovery of the random events that modify the chemical reaction in the activated gas layers.

Jan 1, 1948

By J. A. Bustnes

The present work deals with kinetic studies of the reduction of molybdenum- and tungsten oxides by hydrogen. The experimental method used was therrnogravimetry under isothermal as well as non-isothermal conditions. The non-isothermal kinetics in the case of the reduction of MOO, to Moo2 has been modeled considering surface reaction as rate- controlling. In the case of the reduction of W02 to W a model was developed on the basis of the movement of the reaction front. The activation energies calculated on the basis of the models were in good agreement with those derived from isothermal experiments.

Jan 1, 1994

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By J Lea, D C. Kettlewell

The Carina iron ore deposit lies 105 km northeast of Southern Cross, WA. The area designated the Yilgarn Iron Ore Project (YIOP) is comprised of five prospects along an east-southeast trending greenstone belt that extends from the Helena-Aurora Ranges in the northwest to the Yendilberrin Hills in the southeast, over a strike length of approximately 40 km. The YIOP project encompasses the previously identified iron deposits of Bungalbin, Bungalbin East and Mt Walton. The Carina deposit was discovered by Polaris Metals NL in May 2007. The Carina deposit is located within and parallel to the structurally complex northwest trending Mount Dimer shear zone. The volcanosedimentary Archaean-aged greenstone sequence consists of ultramafic and mafic lavas and flows with interbedded sediments dominated by chert and banded iron formation (BIF). Supergene enrichment processes formed a goethite orebody replacement of BIF sequences within a doubly plunging synclinal fold structure. Mineralised outcrops dominated by goethite form a low ridge 1500 m long, up to 90 m wide and drilled to over 200 m in depth. In the vicinity of the Carina deposit, iron occurrences have been identified over at least a 12 km strike length and the exploration potential of the area is identified as 30 - 40 Mt. Polaris Metals began exploration in the area in 2006. Target generation in the area used existing state geological survey maps and regional magnetic survey data to focus on BIF occurrences associated with major structures. Early field investigations resulted in the identification of a large outcrop of predominantly goethite mineralisation at Carina. Detailed geological and structural mapping was completed, followed by close-spaced reverse circulation and diamond drilling. The mineralisation is predominantly goethite with specular and coarse platy haematite localised along structures that cut the goethite mineralisation. Mineralised zones are moderately vuggy and larger cavities occur in proximity to fault zones that transect the orebody. A capping by a thin veneer up to 9 m thick of canga or ferricrete occurs in places. By December 2008, 178 reverse circulation and 11 diamond drill holes (seven surface holes, four tails) were completed. The current JORC-compliant resource estimate is based on assays from 72 RC drill holes and using a 55 per cent Fe cut-off stands as an Inferred Resource of 27.9 Mt at 58.6 per cent Fe, 1.3 per cent Al2O3, 3.7 per cent SiO2, 0.09 per cent P, and 10.1 per cent LOI. Assaying has recently been completed and will be incorporated into a new updated resource later in 2009.

Jan 1, 2009

By L. M. Oshinowo

The incorporation of advanced analysis tools, such as CFD, into the process plant design process has become possible through advances in commercially available computational fluid dynamics software and faster computers. Multiphase modeling is now typically employed in the design phase of process plant design at Hatch. The multiphase models include Lagrange-Euler and Euler-Euler treatment of the multiple phases. Additionally, mixture models with interface-sharpening algorithms are applied to the prediction of free-surface flows in complex geometry. CFD is applied to applications where traditional design rules are not applicable. The additional rigor of CFD modeling in 2D and 3D allows process engineers to come closer to realizing true virtual plant design. The objective of this paper is to outline the benefits and pitfalls in the application of multiphase modeling for rigorous design. Several application examples in the hydrometallurgical field will be presented.

Jan 1, 2005

By D. J. Esdale, D. F. Pridmore, F. W. Lindman, J. H. Coggon

Almost all the presently viable nickel reserves in the Yilgarn Block contain nickel in a sulphide phase. Both volcanic peridotite- associated (VPA) deposits and intrusive dunite-associated (IDA) deposits are characterized by massive, matrix and disseminated sulphides (typically, pyrrhotite, pentlandite, pyrite, chalcopyrite, magnetite and other spinels), though in the IDA deposits the volume of disseminated sulphides is far greater than that in the VPA deposits. Potentially all geophysical techniques have application in the direct detection of these deposits'gravity for the detection of the dense massive and matrix ore; magnetics for the detection of magnetite and pyrrhotite in the ores; electromagnetics for the detection of the massive and matrix ore; and induced polarization for the detection of disseminated and to some extent matrix and massive ore. In practice the application of geophysical techniques is limited to a varying extent by (1) the relatively small size of an economic accumulation of sulphides, particularly the VPA deposits, (2) the extreme depth of weathering and lack of outcrop on the Yilgarn Block and (3) the abundance of geological noise or anomalous responses caused by sources other than economic mineralization.

Jan 1, 1984

By W. A. McKinney

Bureau of Mines Research has demonstrated that it is technically feasible to segregate oxidized copper ores by use of a direct-fired, refractory-lined rotary kiln. Previously, the segregation process had been effected only in much more complicated indirect-fired, stainless steel kilns, The method comprises heating crushed ore premixed with small quantities of salt and carbonaceous material, such as coke, to about 830° C to produce copper as fine flake and metallic films on the surface of the coke particles. After grinding of the cooled furnace calcines, the copper is recovered by conventional flotation. During direct-fired segregation it was necessary to closely control the air-gas mixture in the burner. Good copper recoveries were obtained only when adding air in the limited range of 1.15 to 1.2 times the theoretical amount required for combustion of the natural gas. Batch trials of the new technique on quartzite-, limestone-, sandstone-, and limonite-type oxidized copper ores containing from 1.4 to 6.2 percent copper yielded flotation concentrates containing from 3.7 to 45 percent copper, representing 84 to 95 percent recoveries. Analyses of the furnace gases showed that loss of copper by volatilization was negligible. The preliminary direct-firing segregation studies were complemented by continuous runs on the quartzite ore, containing 1.4 percent copper, in an integrated segregation-flotation pilot plant having a 60 pound-per-hour capacity. In a typical test, 84 percent of the copper was recovered in a cleaner flotation product containing 25 percent copper. The study will be continued to further delineate the conditions for good segregation as effective use of standard ceramic-lined kilns will render the process more attractive from a commercial standpoint.

Jan 1, 1963

By W. Zhang

"The adsorption of collector on chalcocite has been studied in situ in aqueous solutions by applying an atomic force microscopy (AFM). The AFM images show that xanthate, such as potassium ethyl xanthate (KEX) and potassium amyl xanthate (PAX), adsorbs strongly on chalcocite mainly in the form of insoluble metal xanthate, which binds strongly with the mineral surface without being removed by flushing with ethanol alcohol. The result clearly shows that the adsorption of xanthate on chalcocite is totally different from its adsorption on chalcopyrite, during which oily dixanthogen is the main adsorption product on chalcopyrite surface. AFM images also showed that increasing solution pH to 10 doesn’t prevent the adsorption of xanthate on chalcocite much and the result confirms with the fact that chalcocite floats well in a wide pH range up to 12 with xanthate being used as a collector. INTRODUCTION In flotation, the adsorption of collector on mineral surface is vital for a successful flotation process to achieve a satisfying metal recovery. Historically, many works have been carried out to clarify the adsorption mechanism of collectors on sulfides. (Gaudin and Schuhmann, 1936, Poling and Leja, 1963; Allison et al., 1972, Fuerstenau, 1982; Leja, 1982; Woods, 1984) The adsorption of xanthate on chalcocite surface in aqueous solution also attracted the interest of many researches. Gaudin and his colleagues (Gaudin et al., 1934; Gaudin and Schuhmann, 1936) studied the solubility of potassium ethyl xanthate and its reaction products in organic solvents and firstly proposed there was initially chemisorbed xanthate (X-) on chalcocite surface followed by insoluble cuprous xanthate (CuX). Allison et al. (1972) studied the reaction products of various sulfide minerals with xanthate solutions and reported that the measured rest potential of chalcocite in 6.25×10-4 M KEX solution at pH 7 was +60 mV and the reaction product of PAX on chalcocite was cuprous xanthate. Mielczarski and Suoninen (1984a, 1984b) applied the XPS and studied the adsorption of potassium ethyl xanthate on cuprous sulfide. It was reported that there was a relatively rapid formation of a well-oriented monolayer of xanthate ions followed by a slow growth of disordered cuprous xanthate molecules on top of this layer. Richardson et al. (1984) carried out an electrochemical study of chalcocite flotation with the addition of ethyl xanthate. It was proposed that cuprous xanthate and possibly cupric xanthate were adsorbed hydrophobic species on chalcocite surface due to the exchange and charge transfer oxidation reactions. Leppinen et al. (1989) applied an in-situ FTIR study of ethyl xanthate adsorption on sulfide minerals under conditions of controlled potential and they concluded that, for chalcocite, there were three different potential regions of xanthate adsorption, including chemisorption, copper ethyl xanthate formation on the surface and multilayer formation."

Jan 1, 2015

By J. R. Heberger

"The Safety Pays in Mining web application, developed by the National Institute for Occupational Safety and Health (NIOSH) Mining Program, helps mines determine the potential costs associated with mining injuries. This web app groups injuries by type, either by the cause of the injury or by the nature of the injury. When the user selects one of over 30 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, Safety Pays in Mining will estimate the total costs of the selected injuries, including an estimate of additional indirect costs, the estimated impact of total injury costs on mining company profits, and provide some examples of other items (services, equipment) on which companies could spend the savings that result from the prevention of injuries. This paper reviews the Safety Pays in Mining web application by discussing the development of the app, how it is used to show the true costs of mining injuries, and how mines can benefit from using this app. INTRODUCTION Injuries on the job cause pain and suffering. They can also profoundly affect profits and daily operations. In addition to paying direct costs or increased premiums for workers’ compensation insurance, a company might need to pay overtime for other workers to fill an injured worker’s job role, cover training costs for a replacement worker, or divert administrative resources in the wake of an injury. Safety Pays in Mining is a web app that estimates the distribution of these injury costs and assesses the impact that occupational injuries have on a company’s profits. The costs of specific types of occupational injuries in mining are not readily available as mining and insurance companies don’t usually share this information. As a consequence, companies only have cost information based on previous experience with their own employees. Therefore, if a mine never experienced a finger amputation for one of its miners, it would not be aware of the possible costs associated with this type of injury. In addition, injury costs are unique in that the cost distribution is so wide — with half of the injuries in our dataset having mean costs higher than 90th percentile costs — just using the average cost of a specific injury type does not provide adequate information. Some injuries involve immensely high costs, and even though the risk of these high-cost injuries occurring is low, mines need to be aware of their potential impact on their company’s financial health."

Jan 1, 2018