Search Documents

By S a m u e l D e a n

The author's written response to previous discussion was presented at the North of England Institute of Mining and Mechanical Engineers general meeting held in Newcastle-upon-Tyne, 8 April 1916, followed by further comments by Hare S. in support of his view that the conditions in English mines were the reason for less satisfactory results being obtained with heading machines and brief comments by Greener T.Y., President

Dec 1, 1916

By S Serp, M Duchateau, P Chevreux

Molten salt reactor (MSR) is a promising advanced reactor system aiming to the transmutation of minor actinides such as americium in order to reduce the inventory of ultimate nuclear waste. The fuel is a molten salt in which actinides are homogeneously dissolved in the liquid phase. A chloride salt may be retained for this concept, as it provides low melting point, high solubility of actinides, harder neutron spectrum. To avoid corrosion and precipitation issues, molten salt composition has to be carefully controlled with impurity content as low as possible. Obtaining pure actinide chlorides without contaminants such as oxide, oxychloride, hydroxide and water is still a challenge. To prepare actinide-bearing salt, the chlorination of actinides oxides was investigated in an unstirred reactor under flowing gas as solid-gas reaction. The carbochlorination of PuO2 were performed in the temperature range of 600 to 800°C with chlorine gas as a chlorinating agent and the presence of solid carbon. PuCl3 was successfully synthesised by this method and characterised by X-ray diffraction measurements but some impurities such as oxide phase remain inside the formed product. Refinements of anhydrous and hydrated PuCl3 phases by Le Bail method were also performed for crystalline materials definition. Conversion mainly depends on the chlorinating temperature and the contact between the oxide and the chlorinating agent. A conversion value of 70–80 per cent was achieved at 700°C from PuO2 with quite high specific surface area. The conversion rate was not improved with increasing the chlorination time. The volatilisation of Pu was observed during the carbochlorination experiments. To avoid a loss of Pu caused by sublimation, the chlorination temperature should be limited to 650°C despite that the conversion of PuO2 to PuCl3 was enhanced by increasing temperature. Both carbochlorination and hydrochlorination of AmO2 were also carried out leading to the formation of AmCl3. These first results suggest that americium oxide was chlorinated more readily than plutonium oxide. The purity of produced PuCl3 and AmCl3 still deserves further investigations.

Jun 19, 2024

By A Simmons, J Chan, A Li, Q Gu, D M. Brett

The paper presents an example of field density achievements using thin layer deposition and solar drying and compares this with compaction data from laboratory testing and field trials of mechanical densification processes.

Jul 1, 2021

By H Yuan, H Tian, Y Zhang, Z Wang, C Wang

Submerged arc welding (SAW) is one of the significant metal-joining processes for manufacturing marine vessels, steel pipes, and offshore structures with high deposition rate and engineering reliability. Welding flux serves several essential functions, including atmospheric shielding, arc stabilisation, bead morphology control and weld metal (WM) refinement. Therefore, from a thermodynamic point of view, the focus for flux design and WM compositional/microstructural modification has been placed to elucidating the transfer pathways and mechanisms of major alloying elements, such as Si, Mn, Ti and O during welding. To this end, a thermodynamic model has been established to predict alloying element contents in the WM. Such functions are enabled by the physicochemical properties of the fluxes, which are inherently rooted in the nature of the fluxes. A unique yet systematical investigation, including physicochemical property changes and structural evolution behaviours, has been conducted over the wide range of fluxes applied to actual welding of EH36 shipbuilding steels. Combined with spectroscopic methods, structural behaviours of network formers such as SiO2, Al2O3 and TiO2 and network modifiers such as MgO, MnO and CaO have been illustrated. Viscosity and ionic conductivity have been found to be positively associated with the degree of polymerisation.

Aug 21, 2024

By Christian Hoyme, Jochen Maurer

Most of the current foundation projects are suffering from disconnected information silos. In the first silo there is the planning of the project with corresponding data, presented by paper or digital drawings. Here will Building Information Modeling (BIM) be one of the trends for the future. We will see more and more projects leaving the “old way” of 2D drawings and moving into 3D planning including metadata of the foundations. But even with a perfect BIM model of a jobsite, we are not at final end of digitalization. While execution of the project at the jobsite, a second data silo is evolving. Data collected directly from construction equipment and manual measurements is currently undervalued in most projects. Paper is passed to the equipment operator and major data from measurements on site are noted on paper and digitized afterwards. Automatically collected data is not be used to create site progress reports or similar report. So, the real “data” just flows around without connection to any other data already existing in projects. And then the third silo arises: The documentation of the project. Data collected on paper es reentered to create some basic documentation of the work handed over to the client. Spreadsheet software is still the “tool-to-be-used” to create at least some documentation. Finally, the documentation is not connected to the data created while planning and not connected to the automatically collected data from the jobsite. A connected jobsite in the foundation industry must link these information silos and have to create a full data-workflow from the design through the execution to the as-built documentation. INTRODUCTION Building information modelling (BIM) is currently the most popular term of construction business in Germany and probably all over the world. But as often there are many different definitions out there and everyone has his own definition or at least understanding what BIM is about. But for sure it is the most relevant for the construction industry in the near future. Most popular is the digital twin for the upper structure of a building. In most cases the BIM models just shows the building itself, but there is more to be implemented. For example: projects where a special foundation is needed, BIM should include also the foundation elements with meta data. There are several advantages. Not only the clash detection of anchors, but also the possibilities to check the interaction with neighbor constructions, power lines and so on are a use case. For sure most of the special foundation elements are not relevant for the whole lifecycle of a building. But during construction and later the demolition the information about the hidden elements is important and gives a benefit to all stakeholders. In the future there will be not the question: “What is already in the ground?”. The risk for following construction projects on the same ground will be minimized.

Jan 1, 2019

By Agus Sasmito, Akash Adhikari, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Previous studies on blast fumes(CO + NO2) clearance and workplace re-entry time have overlooked the effects of toxic gases entrapped in the muckpile. The currently available models forcalculatingthe mine re-entry times assume that all post-blast fumes are emitted upon detonation. However,recentstudies reportedthat as much as 60% to 70% of the fumes or gases produced during an underground development blasting couldremain entrapped in the adjacent rock mass or in the muckpile. Entrapped fumes are slowly released,and when disturbed, high concentrations are released, representing a possible risk during the digging and transportation of the muckpile. This study uses CFD, SC-Flow software to understandthe behaviorof the entrapped fumes and theireffect on mine re-entry time.

Feb 1, 2020

By C J. Greet, J Kinal, C Hitchen

Following the successful completion of a marked ball test defining the potential wear benefits the high chrome alloys may offer against forged steel, as well as laboratory test work investigating changes in pulp chemistry and improvements to metallurgical performance, a plant trial was commissioned at NewcrestÆs Ridgeway concentrator. The paper briefly describes these results.Newcrest decided to convert their media charge by the top-up method. To monitor the trial a sampling protocol was put in place whereby the pulp chemistry was monitored before, during and after the purge. The metallurgical shift data was analysed using various statistical methods to determine if the metallurgical performance had improved with the change in grinding media. While the analysis indicated that the metallurgy had improved, not all of the benefits could be assigned to the change in grinding media alone. However, the combination of reduction in media wear and the increases in copper and gold recoveries suggested that it was economically viable to operate with high chrome grinding media.As with many trials of this nature the prevailing economic conditions are fluid and a decision was made to revert back to forged steel grinding media in an effort to reduce operating costs. It was further agreed that Magotteaux could monitor the pulp chemistry and metallurgical changes in this reverse trial to confirm the results observed in the earlier conversion to high chrome grinding media.CITATION:Greet, C J, Hitchen, C and Kinal, J, 2012. Conducting high chrome grinding media trials at NewcrestÆs Ridgeway Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 56-64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Brian FitzPatrick, Michael J. Weaver

Everyone has a role in site safety, even consultants. This paper presents a summary of how a geotechnical and environmental consulting firm, with field staff on construction and subsurface explorations sites, engaged their staff and leveraged relationships with contractors to assess the construction related risks to which its staff members are exposed. These findings were then integrated into their technical training materials for both new staff and those needing a refresher, so that safety is discussed at the same time as the technical work and not treated as a separate topic. The paper outlines the process of identifying and evaluating the construction related risks that staff members face and presents examples of how the consultant can engage contractors in the process. By doing this, knowledge can be shared and there is a better mutual understanding of the risks associated with common construction and exploration related field tasks. The work resulted in an increase in staff engagement in safety, a better understanding of the true risks that staff face in the field, better relationships with contractors, and lower safety metrics. HISTORY At Haley & Aldrich, Inc., we renewed our safety journey in May 2012. Like many others, we had concerns over injuries our staff experienced in the three previous years, and a potentially significant utility strike we experienced while excavating a trench. In 2009, 2010 and 2011 we experienced an increase in recordable injuries, including two significant injuries, which caused our Experience Modification Rate (EMR) (see note below), Total Recordable Incident Rate (TRIR), and Days Away-Restricted, and Transferred Rate (DART) to rise significantly. See Fig. 1 for details. This caused us to step back and review our approach to safety, and our “safety culture”. The rise in reportable incidents and injuries also corresponded to the beginning of a growth period for the company.

Jan 1, 2019

By Karsten Beckhaus

Barrier walls in levees and dams are designed and constructed for new structures and for rehabilitation or upgrade of existing structures to control seepage. Construction methods applied are often deep soil mixing with a cementitious slurry or excavating a trench and refilling it with a plastic concrete. This paper explains the technical background of jointless cementitious barrier walls inevitably developing thermal tensile stresses and how these stresses can be controlled. The theoretical background of thermal stresses is explained based on experimental and numerical studies of essential factors. Although a low cracking risk is generally inherent, risk mitigation measures should be taken to thermal cracking and to ensure the permanent function of such walls as a low-permeability and high-deformability barriers.

Sep 8, 2021

By Diego Bellato

Production data recorded by special foundation rigs during construction activities at the site are commonly used for quality assurance / quality control procedures and, in particular, to prove that the installed foundation elements comply with the geometrical and quality requirements defined in the design specifications. Parameters such as crowd force, penetration/withdrawal rate, rotational speed etc. are usually presented in reports in the form of depth and/or time profiles. This type of protocols are already standard QA/QC solutions for ground improvement methods like deep soil mixing or jet-grouting, but they are quite rarely applied in combination with other techniques like diaphragm walls or Kelly drilling. In the latter cases, one of the main reasons behind this lack of site documentation is related to the difficulty in interpreting huge amount of data collected during the creation of single elements, which, in some cases, can last several days (not always in a row). In addition, the building sequence is often characterized by many alternated operations involving different movements of the rig and the use of different tools. In this context, the identification of specific construction activities based only on the mere exam of the time profiles of the recorded production parameters is extremely difficult. In this paper, the time profiles of production parameters obtained from a fully-cased Kelly drilling rig employed on a site in Karlsruhe (Germany) have been investigated and compared with a detailed series of activities deduced from a video filmed during installation. Typical time profile patterns associated to specific procedures have been identified by combining the different information available. The outcome of this study helped project engineers to automatize the recognition of activities directly from production data and led to an overall understanding and optimization of the construction process. INTRODUCTION The special foundation industry is characterized by the use of highly sophisticated machinery for the realization of geotechnical systems such as piled rafts, retaining walls and slabs for excavation pits, cut-off walls for levees and embankments or ground improvement solutions. Rigs can vary in size, weight, and power and can be provided with several drilling tools to cope with the different soil conditions (e.g. clay, sand, rock) and the different geometries of the elements to be built at the site (e.g. micro-piles, large- diameter bored piles, diaphragm walls, anchors). Due to the challenging construction procedures, various types of sensors have started to be mounted on the equipment in the last decades to monitor the behavior of some important machine parameters and to inform rig operators about the on-going process and the status of their devices.

Jan 1, 2019

By Anthony T. C. Goh

"For deep excavations in soft clay, it is common to use jet grouting piles (JGP) prior to excavation to minimize wall deflections and ground settlement, and to prevent basal heave instability. In this paper, finite element analyses were carried out to assess the basal heave factor of safety for excavations in soft clay supported by JGP. Comparison of the factor of safety from the finite element analyses with limit equilibrium methods was then performed. Subsequently, to account for the uncertainties in the soil and JGP properties, a simplified reliability analysis procedure is proposed to estimate the probability of basal heave failure for deep excavations supported by JGP.INTRODUCTIONJet grout piles (JGP) are often used to prevent basal heave instability and to minimize excessive wall and ground movements associated with deep excavations in soft clay deposits (Shirlaw 2003; Wen 2005; Ou 2006). The jet grouting process which is carried out prior to any excavation works produces a series of short overlapping grout columns resulting in a “continuous” base slab (commonly termed as jet grout pile or JGP) below the final excavation level that spans across the entire excavation (Gaba 1990; Hsieh et al. 2003; Ho and Hu 2006). Typically, the JGP thickness ranges from 2 m to 4 m.The focus of this paper is on the assessment of basal heave instability for deep excavations in clay stabilized with JGP. Finite element analyses were first conducted to determine the basal heave factor of safety for deep excavations in clay with JGP. Comparisons were then carried out with factors of safety based on conventional limit equilibrium methods. Since the conventional factor of safety approach does not explicitly reflect the uncertainties of the soil and JGP properties, it is demonstrated in this paper that a simple reliability based approach (Hasofer and Lind 1974) can be used to assess the probability of basal heave failure.LIMIT EQUILIBRIUM METHODFor excavations is clay, the Terzaghi (1943), Bjerrum and Eide (1956) and Eide et al. (1972) methods which are based on bearing capacity theory, are commonly used to determine the basal heave factor of safety. Another commonly adopted method in Japan and Taiwan is the slip circle method which involves taking moments about the lowest strut level (JSA 1988; Hsieh et al. 2008; Luo et al. 2012). The slip circle method has also been applied for excavations with a JGP at the base by incorporating the undrained shear strength of the JGP. In the slip circle method, the basal heave factor of safety FSslip is assessed by taking moments about the lowest strut level (Fig. 1)"

Jan 1, 1900

By Selim Coskun

In this study, tungsten matrix composites reinforced with 2 wt% TiC particles were mechanically alloyed (MA?d) for 3h, 6h, 12h and 24h. 1 wt% Ni is used as sintering aid which is added before and after mechanical alloying. Microstructural and phase characterizations of composite powders and sintered samples were carried out via SEM and XRD analyses. Furthermore, density and hardness measurements of as-consolidated and sintered samples were carried out. Additionally, DSC experiments were conducted to investigate the sintering behavior of the MA?d powders.

Jan 1, 2009

By Juan M. Pestana, Jeremy M. Gasser, Cuneyt Gokmen, Paul J. Sabatini, William Tanner, Daniel J. Woeste

An access pathway and working platform were designed and constructed for equipment access for a Deep Soil Mixing (DSM) pilot study over a coal combustion residual (CCR) surface impoundment (SI). The DSM pilot study was conducted to evaluate slurry mix designs and construction techniques for installing DSM columns up to 95 feet deep. Two-dimensional (2-D) limit equilibrium and 2-D finite element analyses were used to evaluate multiple failure mechanisms including: (i) bearing capacity, (ii) punching shear of mixed ground and underlying CCR, (iii) effect of fluidized DSM columns on working platform stability, and (iv) liquefaction. The analysis results were used to design ground improvement required to increase bearing capacity and stability of the CCR under the proposed equipment access route. A long-reach excavator was used to perform shallow bucket mixing and walk onto the CCR SI atop previously mixed cells following a minimum cure time and acceptance of quality control test results. Prior to mobilizing the DSM rig, a static load test was conducted to evaluate performance of the working platform. Both the access pathway and working platform demonstrated acceptable performance under the design loads during the DSM pilot study. This case study emphasizes the economic and safety benefits that can be realized by appropriately designing critical temporary work items such as access pathways and working platforms in difficult ground conditions. INTRODUCTION A Deep Soil Mixing (DSM) pilot study was conducted at a coal combustion residual (CCR) surface impoundment (SI) to evaluate slurry mix designs and construction techniques for closure design of the SI (Site). Sluicing of CCR at the facility ceased and closure will be initiated based on requirements in the final United States Environmental Protection Agency (USEPA) Rule for Disposal of Coal Combustion Residuals from Electric Utilities, 40 CFR 257, effective October 19, 2015. The proposed closure approach involves constructing a DSM containment structure (DSM Wall) to separate the SI into two areas: (i) a closure by removal area; and (ii) a consolidate and cap-in-place area. The proposed DSM Wall would retain the CCR within the consolidated closure footprint and provide a barrier between the two areas of the SI. The predominant CCR in the SI where the pilot study was conducted were fly ash and bottom ash. CCR materials in surface impoundments are generally soft and saturated as a result of being sluiced into place and can present stability and safety challenges when performing earthwork activities.

Jan 1, 2019

By D. A. Cowen

Toll and custom treatment of base metal concentrates have been performed for decades as mines and concentrators are developed distant from capital and, energy-intensive smelting and refining facilities. Commercial treatment terms have been developed and refined for over a century, and are negotiated taking into account a complex array of quality and economic factors. Treatment of third-party concentrates in the South African platinum industry is a comparatively recent development, brought about by the opening up of mineral rights and operations being developed that are smaller than the critical size required to sustain capitalization of smelting or refining plant. Published commercial terms have not been demonstrated to reflect the complexities and subtleties of base metal concentrate markets. This paper outlines some key elements and parameter ranges of base metal concentrate treatment contracts, and applies similar principles to typical Merensky and UG2 platinum group element (PGE) concentrates to determine potential value distribution between the mining and treatment parties in tolling arrangements.

Jan 1, 2012

By Lynn Salvati, Colin LaVassar, Loic Galisson, Joel Theodore, Lynette Sla

"Sound Transit’s University Link and Northgate Link projects will add 6.75 miles (10.9 km) of twin-bored tunnel to Seattle’s light rail system, extending the route north from downtown Seattle. The tunnels are being constructed primarily in glacial soils using pressurized-face tunnel boring machines. Cover over the tunnel alignment varied from 13 feet to over 300 feet (4–91 m). Since the tunnels are located in densely populated urban areas, controlling ground movements and monitoring settlement were essential to success of these projects. Hundreds of geotechnical instruments, including extensometers, surface settlement points, and near-surface settlement points, were used in both projects to monitor settlement. The observed data were compared to settlement predictions made prior to tunneling, and analyses performed to update empirical factors to better estimate settlements. Recommendations for designing efficient and cost-effective settlement monitoring programs are provided based on the review of the monitoring data and analyses.INTRODUCTIONThe paper includes data from Sound Transit’s University Link and Northgate Link projects. These projects will add 6.75 miles of twin-bored tunnel to Seattle’s light rail system. The tunneling for University Link will extend the light rail system from downtown Seattle to the University of Washington. Tunneling from downtown Seattle to the Capitol Hill Station was completed under the U230 contract, and tunneling from the Capitol Hill Station to the University of Washington Station was completed under the U220 contract. The Northgate Link extension will extend the light rail line north of the University of Washington, including approximately 3.5 miles (5.6 km) of twin tunnels between the University of Washington Station and the Maple Leaf Portal and two stations, U District Station and Roosevelt Station. Tunneling for the Northgate Link project is still underway as part of the N125 project. At the time of writing, tunneling from the Maple Leaf Portal to Roosevelt Station has been completed. Therefore data labeled as N125 in this paper only include the portion of the alignment from the Maple Leaf Portal to Roosevelt Station."

Jan 1, 2016

By A. Melkumyan, M. Balamurali, J. Zigman

Understanding the contribution of geophysical variables is vital for identifying ore indicator regions. Both magnetometry and gamma-rays are used to identify the geophysical signatures of the rocks. Density is another key variable for tonnage estimation in mining, and needs to be re-estimated in areas of change when a boundary update has been conducted. Modelling these geophysical variables in 3D will enable investigation of the properties of the rocks and improve our understanding of the ore. The Gaussian Process (GP) was previously used to generate 3D spatial models for grade estimation using geochemical assays. This study investigates the influence of the following two factors on the GP-based autonomously generated 3D geophysical models: the resolution of the input data, and the number of nearest samples used in the training process. A case study conducted on a typical Hammersley Ranges iron ore deposit using geophysical logs, including density, collected from the exploration holes, is examined in this paper.

Sep 1, 2021

By M. Balamurali, K. M. Seiler

Modelling stockpiles is a key factor of a project’s economics and operation in mining, because not all the mined ores are not able to mill for many reasons. Furthermore, the financial value of the ore in the stockpile needs to be reflected on the balance sheet. Therefore, automatically tracking the boundaries of the stockpile facilitates the mine scheduling engineers to calculate the tonnage of the ore remaining in the stockpile. This paper suggests how the dynamic of stockpile shape changes caused by dumping and reclaiming operations can be inferred using polygon models. The paper also demonstrates how the geometry of stockpiles can be inferred in the absence of reclaimed bucket information, in which case the reclaim polygons are established using the digger’s global positioning system (GPS) positional data at the time of truck loading. This work further compares two polygon models for creating 2D shapes.

Sep 1, 2021

By Thomas Jancic

Two of the open-pit, copper-molybdenum mining operations of Duval Corporation are located in the foothills of the Sierrita Mountains approximately 30 miles southwest of Tucson, Arizona. In March 1959, mining from a moderate sized porphyry deposit known as the "Esperanza orebody" was begun at a rate of 10,000 tons of ore per day. Some five years later, a sizeable group of mineral claims west of Esperanza became available to Duval. Earlier exploration and development drilling in this area by others indicated an orebody of greater size but lower tenor than that of Esperanza. A drilling program conducted by Duval not only verified the results of the prior drilling but in addition, revealed a continuation of the mineralization to the south and east. Thus was developed the Sierrita orebody. Open pit design delineated 414 million tons of ore containing an average copper content of 0.35 percent and a molybdenum content of 0.036 percent. In April 1966, the office of Emergency Planning authorized General Services Administration to undertake a program under the Defense Production Act to en¬courage additional domestic production of copper in the interest of national defense. Duval's Sierrita Project was brought to GSA's attention in May 1966 on November 28, 1967, an agreement providing for the development of the Sierrita Property was consummated with GSA. In March 1970, the first copper-molybdenum concentrates were produced in the 72,000 tons-per-day concentrator. Pre-production stripping exceeded the scheduled 105 million tons despite the comparatively short lead time available to equip the mine, build the mine plant facilities, and staff the technical, supervisory, and labor forces. Shortly before the first concentrates were produced, plans were being formulated for a program to increase processing capacity by approximately 15 percent, which entailed increasing overall mining capacity by approximately 50,000 tons per day. This program is scheduled for completion early in 1971.

Jan 1, 1971

By G. E. Norman, J. F. Jackson, A. L. Mckague

"The treatment of nickel-copper concentrate in the new smelter at Falconbridge Nickel Mines Limited, Falconbridge, Ontario, is described. The concentrate in a slurry form is partially roasted in a fluid-bed roaster and the calcine is smelted in an electric furnace. The roaster gases are treated in an acid plant. IntroductionSmelting began at Falconbridge in 1930 with the first blast furnace treating high-grade ore containing 2-3% nickel. In 1933, the Falconbridge concentrator was built and started producing a bulk sulphide concentrate containing 4% nickel. A sinter plant was built to agglomerate and partially roast this concentrate. The sinter was smelted in blast furnaces along with high. grade magnetic ore. Matte from the furnaces was treated in Pierce-Smith converters to produce shipping matte which was refined at the company's plant in Norway."

Jan 1, 1980

This paper discusses equipment replacement strategies and specifically addresses the upgrading of technologically superseded equipment. The process of equipment replacement evaluations is reviewed, and areas have been highlighted where currently accepted practice results in a bias towards retaining existing equipment longer than otherwise justified. The Discounted Average Cost Method is described and the advantages of the technique for this style of decision making discussed. Several key issues influencing the replacement evaluation are also presented together with examples from recent consulting work.

Jan 1, 1992