Search Documents

By Luis W. Pommier

Large quantities of sea sludge containing halogenated organic compounds, such as PCB, oils and metals like arsenic and lead have accumulated throughout the years at the bottom of sea channels and harbors and are obstructing navigation and creating environmental problems which need to be resolved. A sludge from a California port would be dredged by suction pumps, it would be processed in a plant which would be built either on firm soil or on floating platforms. The sludge shows contents of up to 1 ppm of PCB, 15 % oil and 10 ppm of arsenic, which generates a very fetid odor. Bench scale work indicates that most of the contamination concentrates on the solid phase, in fact, only minor amounts of oil report to the sea water and can be readily removed by physical means. After separation of the sea water from the solids of the sludge by decantation, it is possible to solubilize the PCB, the oil and the metals into an organic solvent leaving a non-hazardous soil for disposal near the harbor. The PCB is dehalogenated during the solubilization process leaving a liquor solution containing the oil and metals. The oil is extracted leaving an aqueous solution containing the arsenic. Further process extracts the arsenic from this solution rendering the liquid non-hazardous. Transportation and disposal of the sludge is impractical. There are hundreds of thousands of tons of hazardous soils accumulated in each harbor, which would fill the hazardous waste disposal sites available and it would be, prohibitively expensive to do so. It is not possible to compare the costs of decontamination with a competitive method. If it were, the proposed process would be less expensive than transportation and disposal and it has the advantage of removing the liabilities from the Responsible party. After a full scale continuous pilot project is run to decontaminate a small, 500 cubic yards accumulation of this type of sludge in a California harbor, a full scale environmental project would be initiated. The decontamination of one million tons of sludge would be completed in five years.

Jan 1, 1995

By Deyou Yin, Kongfang Feng, Bo Wang, Jieyu Zhang, Xin Hong, Shaobo Zheng, Jinyin Xie

"The flow patterns and mixing characteristics in a water model of C-H2 smelting reduction furnace are experimentally studied in this paper. Water modeling is employed to investigate the features of gas jet stirring and the fluid flow patterns in the bath of a smelting reduction furnace during the top, bottom, and side combined blowing process. The influence of the gas flow rate for top, bottom and side nozzles, angle, submerged depth of each side nozzles and the height of the top nozzle has been examined. It showed that the gas flow rate of side nozzles and bottom nozzle had a key role on the fluid flow and mixing characteristics. The gas jet from the top nozzle could change the agitation and fluid flow pattern caused by the gas jets from the side nozzles in the bath.IntroductionFacing the current natural resources decrease and the environmental degradation, smelting reduction iron-making technique is believed to be the most representative at present. Mid last century, the concept of producing liquid iron or semi-steel directly from ore fines and inexpensive fuel was the subject of considerable pilot plant development activity. Among these projects, the direct smelting process, which is the reduction and melting of iron-bearing materials by carbon and other hydrocarbons in the vessel containing a molten bath, is the most popular one. A number of direct smelting processes have been developed around the world, e.g. COREX, DIOS, HIsmelt, AISI, ROMELT, etc.These studies put forward a new technology, which through bottom nozzle blowing rich hydrogen, top nozzle blowing rich oxygen and provide preheating ore and solvent, side nozzles blowing oxygen-coal to realize smelting reduction iron-making process. Owing to the metallurgy reactions always in high temperature, which is above 1600 °C, it is difficult to visualize the mixing behavior and measure the desired phenomena in the reduction vessel. With water modeling, the primary advantages are that it is relatively easy to observe and measure the flow phenomena in the bath."

Jan 1, 2011

By E. L. Burwell

Preliminary results of an in situ oil shale retorting experiment conducted by the Bureau of Mines in a shallow bed of Green River oil shale at Rock Springs, Sweetwater County, Wyo., are described. Eleven wells were drilled into a 20-ft-thick section of the shale lying between 68 and 88 It deep, and attempts were made to connect the wells through the shale with a fracture system created by application of high-voltage electricity (electro-linking), hydraulic fracturing, and explosive fracturing. Ignition of the shale through the central well was easily achieved with a propane burner, and shale oil began to collect in three wells within 3 hours. Propane injection was discontinued after 7 days, and combustion continues, although attempts to control the direction of the combustion front have been unsuccessful. Production rates as high as 4 ½ barrels of nil per day have been recorded, but too little is known about underground conditions to permit an estimate of recovery efficiency at this time.

Jan 1, 1969

By M F. L Gibson

The issue of flyrock is very important in the operation of all mineral extraction sites that use blasting. Unlike the other environmental effects of blasting, ground vibrations and air overpressure, flyrock is (or should be) a rare event, with severe consequences which may include damage to property, injury or fatalities. These physical consequences are often matched by a loss in public confidence in the management of the operation, mistrust and bad press. In this work a deterministic analysis of flyrock was carried out using the equations of a particle in motion with drag. The solutions to these equations were used to reproduce the curves of Lundborg et al (1975) for the relationship between flyrock boulder size and maximum ejection distance. A probabilistic approach based on Monte Carlo simulation was built up with the analytical model using published data together with local case study material. A typical quarry blast situation was modelled and estimates of safe standoff distances were determined using risk assessment techniques.

Jan 1, 2001

By Harry E. LeGrand

The purpose of this paper is to outline briefly some basic principles of ground-water hydrology that have application in mine hydrology and to suggest that an understanding of these principles can help to forestall problems that are internal as regards mining operations and external as regards damage or harm to surrounding areas. The development of a mine below the water table pleads for accurate values to answers of hydrologic problems. Such internal problems involve both an inflow of water without adequate drainage facilities and a deficiency of water for the required mining or milling use. Methods which give acceptable quantitative values for the solution of many ground-water problems depend on rather simple geologic structures, characterized chiefly by homogeneous rocks of considerable areal extent. Unfortunately, mining operations are likely to be centered where rocks are not homogeneous. Consequently, methods that attempt to show values of the storage and transmitting capacity of rocks in mining areas must be applied with caution. In spite of complex geology and apparent uniqueness of individual mines and quarries, adherence to some concepts of ground-water occurrence and movement should be helpful to mine operators. Mining operations that extend below the water table disturb the natural hydrologic regimen. Prior to development, the water table slopes away from the site of a mine in at least one direction, but as soon as development begins and water is removed from the mine, the mine becomes the apex of a depressed cone in the water table, causing a convergence in the flow of water toward the mine, The behavior of the cone of depression, as it tends to deepen and to increase in areal extent when the mine is deepened, is related to the rate of withdrawal of water necessary to keep the mine dry. The significance and nature of the cone of depression in the vicinity of pumped wells has been studied by ground-water hydrologists for years, but the cone caused by pumping water from mines has generally been less systematically appraised. The geologic and hydrologic settings of mines range greatly so that a simple standard procedure for dealing with problems

Jan 1, 1972

By A. Onozaki

The Iijima Refinery was put into operation in 1972 and today has an annual production capacity of 156,000 tons of SHG electrolytic zinc. At the Iijima Refinery, the recoveries of gold and silver are 98.0% and 98.2%, respectively. Gold contained originally in the zinc concentrates reports in the Cu-Pb-Ag residue produced in the residue treatment process. Silver contained in the concentrates is distributed between the Cu-Pb~Ag residue and the copper cake produced in the purification process. The Cu-Pb-Ag residue, which contains gold and silver, is sent to the Oyachi flotatfon plant of the Kosaka Smelter; about 82% of the gold and about 85% of the silver are recovered in the copper flotation concentrate.. In this paper, the distribution of gold and silver in the Iijima. Refinery is discussed and operational results of the Oyachi flotation plant are presented.

Jan 1, 1990

By Richard J. Lundin

Literature research is an inexpensive, yet effective tool for the direct discovery of ore deposits. Case studies abundantly demonstrate that properties with viable mineralization and *proven reserves have been overlooked, forgotten. or ignored and can be rediscovered by inexpensive literature search techniques Areal studies s as WaIlaby Enterprises Mining District Data Base Program appear to be more effective than traditional commodity studies. The success of such studies depends on the inclusion of Mineral Clairant Questionnaire Data, Mineral Ownership Data, Field Examination Data and the continual updating of all information. Such studies are valuable for proposed or existing Wilderness Area Evaluations.

Jan 1, 1977

By Q. F. Wang, M. H. Lai, T. Q. Liu, G. G. Dong

Compared with the traditional pre-treatment process, biological oxidation process has many advantages including higher gold recovery, less cost, easier operation. The bio-oxidation reactor is the most important equipment for biological oxidation process. In this paper, the characteristics of biological oxidation are investigated, and the design principles are proposed based on laboratory tests. Both increasing the tank height and taking new inflation system can enhance higher dissolved oxygen. The new type of large-scale industrial bio-oxidation reactor is designed, which is 9.5 m in diameter and 10 m in height. The bio-oxidation reactor metallurgical performance has been tested by industrial-scale experiment. The slurry of flotation concentrate is divided into two parts to feed two bio-oxidation reactors. The feeding rates of two reactors are adjusted on the basis of getting the same content of S, Fe, As in overflow. The result shows that the feeding rate of the new type of 700 m3 bio-oxidation reactor is 3.72 m3 per hour, and the feed rate of the conventional 700 m3 bio-oxidation reactor was 3.23 m3 per hour. The processing capacity of the former is 15.2% higher than that of the later, which demonstrates the new type of bio-oxidation reactor has higher oxidation rate.

Jan 1, 2015

By John N. Murphy

The environmental status of underground mining operations is critical to the health and safety of the miners; particularly in a large mine, the multitude of interacting parameters that can favorably or adversely affect the environ-mental status makes the manpower requirement of the routine checking of specific areas and conditions a formidable one. While the concept of environmental monitoring for miners has been considered for some time, until recently the availability of sensors to reliably measure the parameters of interest severely limited the utility of such systems. The status of sensors for mine use and the evaluation of environmental monitoring systems is reviewed.

Jan 1, 1977

By Chengguo Zhang, Bruce Hebblewhite, Faham Tahmasebinia, lsmet Canbulat

"Coal burst is a dynamic release of energy within the rock (or coal) mass leading to high velocity expulsion of the broken/ failed material into mine openings. This phenomenon has been recognised as one of the most catastrophic failures associated with the coal mining industry, which can often lead to injuries and fatalities of miners as well as significant production losses. This paper aims to examine the mechanisms contributing to coal burst occurrence, with an emphasis on the energy release concept. In this study, a numerical modelling study has been conducted to evaluate the roles and contributions of difference energy components. The energy analysis presented in this paper can help to improve the understanding of energy release mechanisms especially under Australian conditions.INTRODUCTIONCoal burst is one of the most hazardous problems encountered in underground coal mines, which occurs at different locations in a variety of mining systems and operations. This phenomenon always involves a violent and dynamic energy release with large rock mass/coal deformation and ejection that can cause severe damage to openings, equipments and may result in fatalities and injuries.The first coal burst occurrence was reported in Britain in 1738 (Dou 2001). Since then, international experiences are available in Canada, South Africa, USA, former Soviet Union, China, India, France, Germany, Poland and Czechoslovakia. Rice (1935) classified coal bursts as two general types, namely excessive pressure bumps and shock bumps and he further mentioned that pressure bumps are caused when pillar stress exceeds bearing strength. Shock bumps are induced by the breaking of thick, massive strata at a considerable distance above the coal-bed, causing the immediate roof to transmit a shock wave to the coal."

Jan 1, 2016

By Bror Nyrnan

Solvent extraction technology and equipment have been developed within Outokumpu since the early seventies. During this period altogether nine solvent extraction processes for molybdenium, zinc, rhenium, cobalt, nickel, calcium and magnesium have been commercially adopted in Outokumpu's metallurgical plants. During last years a new mixer-settler concept based on a "Vertical Smooth Flow" (VSF) principle has been developed. It has also been found to be a good method for copper solvent extraction, decreasing essentially the crud formation and the organic and aqueous entrainments.

Jan 1, 1994

By Michael E. Karmis

New and developing communication systems en-able underground miners to, not only connect to the surface from an increased communication coverage area, but also to be discovered in the event of an emergency. Communication and tracking systems are required by the U.S. Mine Safety and Health Ad-ministration (MSHA) regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broad-cast devices results in a reliable communication network that can better withstand disruption in daily operation and during a time of emergencies. Research on wireless communication in mines has been ongoing since 1922, when the U.S. Bureau of Mines performed experiments in its experimental mine in Bruceton, PA (Schiffbauer & Brune, 2006a). Ac cording to Dobroski and Stolarczyk (1982), ?as early as 1922, Bureau of Mines experiments showed that radio propagation in mines was possible but not practical.? In 2006, the underground communication technologies available to the mining industry had inherent problems that limited communication capabilities. Because harsh underground mine environments significantly reduce line of sight and propagation range and introduce power and safety concerns, the overall effectiveness of underground communication technologies were limited. After several coal mining accidents in early 2006, the U.S. Congress responded with the Mine Improvement and New Emergency Response (MINER) Act, enacted

Jun 1, 2010

By Ralph V. Stewart

"The asbestos orebody is contained within ultrabasic rocks of Precambrian age, being located in the continuous permafrost zone of the Quebec Ungava Peninsula, some 300 miles north of the tree line at approximate latitude 61'49' and longitude 73°58'.The asbestos deposit is at the western tip of a folded ultrabasic sill complex which trends northeast and covers an elliptical area 4.5 miles wide by 15 miles long. Locally. the asbestos occurs in. a completely serpentinized dunite rock. The principal rock types in the vicinity of the ore-body originally consisted of dunite, peridotite and pyroxenite, all of which have experienced at least two periods of alteration, so that no fresh rock now remains.The main ore zone in the open pit is approximately one quarter mile in length, 150 to 200 feet in width, and plunges at 25 to 30 degrees in a northeast direction below surface, to a vertical depth of at least 1,200 feet, Consider¬able tectonic activity resulted in favourable structural conditions which culminated in the formation of the ore zone in its present form.The deposit consists principally of cross-fibre ""gash type"" veins which vary in length from several inches to several feet. The principal fibre vein direction is parallel to the dip of the enclosing serpentinized dunite and sill complex.Some of the problems encountered during diamond drill¬ing in permafrost are briefly discussed."

Jan 1, 1976

By B. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin. The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill. The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and then two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator’s station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt and mesh sump. The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in turn lowers the miners’ roof exposure per cut. This design reduces the operator’s exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely. INTRODUCTION When mining underground it is necessary to support the roof quickly to prevent it from collapsing after an area has been mined. Since the 1950s, the primary method for supporting the roof has been the installation of roof bolts. Roof bolting is one of the most basic functions yet one of the dangerous jobs in the underground mining operation (1). The Mine Safety and Health Administration’s (MSHA) Health and Safety Accident Classification injury database showed an average of 660 roof bolter operator accidents per year over a 5-year period (1999-2003) (2). The numbers show that roof bolting is the most hazardous machine-related job in underground mining. It represents 39 percent of all machine-related accidents in underground coal mines. In 1993, the U.S. Bureau of Mines conducted a study that has shown the activity of drilling as the most hazardous job task performed by a roof bolter operator, accounting for 31 percent of all roof bolting injuries (3). Almost half (46%) of these drilling injuries were due to falling rocks or coal from the roof. All of these injuries occurred under supported roof. The majority of these injuries (about 99%) are not caused by a major roof collapse but from falls of smaller rock from the immediate roof. This type of roof failure has also been termed “skin fall.”"

Jan 1, 2017

By A. R. Udupa

The reduction roasting behavior of chalcopyrite has been investigated using various combinations of a desulfurizing agent, i.e., CaO or Na2CO3, and a reductant, i.e., CO, H2 or C. Using these, combinations the sulfur is removed from the mineral as CaS or Na2S rather than SO2 as is the case with conventional copper smelting and converting. The laboratory reduction ex¬periments were conducted using thermogravimetric analysis (TGA) and boat tests of mixed combinations of fine particulate reactants subjected to a continuous gas stream. The degrees of metallization were determined by both weight loss and chemical analysis methods and the products examined using optical and scanning electron microscopy and electron probe microanalysis. The percent reduction after one hour at 900°C ranged from 60% to 94%. From these data It was possible to provide postulations as to the controlling reduction mechanisms.

Jan 1, 1983

By A. C. de Araujo, M. G. Barbosa, R. Martino, S. Gaydardzhiev

The Iron Quadrangle district is a world-class iron ore mining district in the region of Belo Horizonte, capital of Minas Gerais state, in Brazil. Many mining companies have been mining high-grade hematite ores for decades throughout the region. The mines reserves often include itabirite ores which are available in high volumes, but have lower iron grades than hematite ores and require elaborated mineral processing to meet the requirements of downstream steelmaking. Itabirite ores have acquired importance, with the depletion of high-grade hematite reserves due to their intensive mining. The objective of this paper is to propose a geometallurgical model for the processing of itabirite ores from an Iron Quadrangle deposit, which will allow predicting the behaviour of ores throughout the deposit, according to their local variations. An initial step consists in characterizing representative samples of the different ores to acquire mineralogical and textural data. Then, itabirite ores of known characteristics are processed with different techniques, in order to extract the trends and key parameters upon which the geometallurgical model is developed. At first, the model takes into account the particle size distribution and its shift during mining and screening, as well as the chemistry and mineralogy of the material. Then, using the previously identified key parameters such as iron recovery, the model predicts the composition of the processing products. Finally, this data is used to model the mineralogy and mass recovery of the products. The geometallurgical model is of great importance, as it is able to model the processing of any sampled ore throughout the deposit. The incorporation of the results in a mining block model will assist mine planning and opens new opportunities for an optimized mining schedule.

Jan 1, 2016

By J. Visman

"Cyclone separators of different design are being used in increasing numbers in the coal industry of today. One recent addition, the Compound Water Cyclone, is finding application in the North American and Australian coal fields for the beneficiation of coking coals and for the reduction of sulphur and ash in steam coals. In this paper, the combination of specific-gravity separation, thickening, classification and water recovery are discussed. All of these operations can now be accomplished by means of cyclones that are effectively combined in circuits of compact design. In the layout of such integrated plants, three main sections are distinguished, namely: a Main Section for cleaning the plus-28-mesh fractions; an Effluent-Beneficiation Section for treating the minus-28-mesh fractions; and a Water-Recovery Section, where the wash water is reconditioned, and the fine solids are removed in a semi-solid state as slugs or pellets. Depending on the nature of the coal and the specifications of the purchaser, water-cyclone circuits can be flexibly combined with HM Cyclones and froth flotation, as well as with ancillary equipment for dewatering and drying."

Jan 1, 1968

By Eurípides do Amaral Vargas Jr., J. A. de Mello Franco

"It is frequently necessary to excavate a tunnel for Civil Engineering purposes, or wells for petroleum exploitation, in laminated rock mass like schists or phyllites or in highly foliated gneisses. The determination of the pre-existing in situ stresses is essential, in order to assure the stability of these excavations. In most cases, the pre-existing triaxial stress field is arbitrary in relation to the tunnel or well axis. For these rock masses the concept of Generalised Plane Strain can be correctly utilized.There are closed form solutions for the calculation of stresses in anisotropic rock masses under Generalised Plane Strain conditions (Lehknitskii, 1981 and Hong , 1994). Based on these analytical solutions, established for the cases of Generalised Plane Strain, a synthetic problem will be formulated: the theoretical in situ stress tensor acting on this rock mass will be determined, with the aid of Bayesian Inverse Problem Techniques, as developed by de Mello Franco (2009). Additionally, the reliability of results obtained will be evaluated, in accordance with the research performed by this author. INTRODUCTIONThe Inverse Problem Technique, as developed in the paper, is based on the definitions and concepts obtained from the current literature and used for the solution of Inverse Problems, but the innovation to be presented is the utilisation of Bayesian Techniques and the determination of the reliability of the results obtained. This will be shown in a synthetic example where the determination of the in situ stress tensor, from strain measurements in a drill hole is supposedly performed. It is assumed that this drill has its axis arbitrarily placed in relation to the rock mass. Generalised Plane Strain conditions will hold for use with problem. The equations of Beltrami – Mitchel, in agreement to Lekhnitskii (1981) and Ong (1994), will be used in this synthetic case, for calculating strains, hypothetically measured in the hole before the final excavations. Finally a synthetic example for the determination of the in situ stress in a fully anisotropic rock mass, based on Bayesian Techniques and its reliability, developed in de Mello Franco (2009) is presented."

Jan 1, 2015

By Susanne Pignolet-Brandom

QEM*SEM is an automated scanning electron microscope/computer system that characterizes samples with regard to mineral modal abundances, mineral grain and particle sizes, mineral associations, and particle surface areas. Additional information, based on the classification of particles according to the area percentage of a mineral of interest, can be obtained for samples of particulates. QEM*SEM is capable of analyzing a wide variety of materials although it was originally developed for applications to the minerals industry.

Jan 1, 1988

By D. Y. Wang, G. Y. Sha, X. L. Shen, D. R. Gu

The study of the volatilization kinetics of zinc and lead in pellets made of zinc-leadbearing dust mixed with coal powder, in a nitrogen atmosphere and at a temperature range between 1100 °C and 1300 °C, shows that the reduction temperature has a significant effect on the volatilization rates of zinc and lead, and that both the particle size of the coal powder and the extra carbon content has no effect on the volatilization rates. The obtained activation energies for the volatilization of zinc and lead are 79.42kJ/mol and 88.74kJ/mol respectively. The volatilization rate of zinc is controlled by the reaction between the zinc oxide and carbon monoxide while that of lead is controlled by the lead evaporation reaction, and the diffusion of gaseous lead through the gas boundary layer covering the surface of the reduced liquid lead.

Jan 1, 2000