Search Documents

By B. J. Scheiner

Extraction of molybdenum from molybdenite ore by an electrolytic oxidation procedure was investigated by the Bureau o f Mines. Various parameters affecting molybdenum extraction, such as salt concentration, temperature, treatment rate, current density, and particle size, were studied. Molybdenum extraction of 95.2 percent was achieved on a laboratory scale from an ore containing 0.35 percent molybdenite. Corresponding power consumption was 24 kwhr per pound of molybdenum extracted with a base consumption of 4.5 pounds of sodium carbonate. Laboratory and pilot plant experiments are in progress on low-grade molybdenum concentrates containing rhenium and copper. Preliminary results indicate that molybdenum extractions in the 90- to 99-percent range and rhenium extractions of 93 to 99 percent can he obtained without appreciable oxidation of associated copper minerals.

Jan 1, 1972

By M Gao

Six new IsaMills were installed for the George Fisher flowsheet in the Lead/Zinc Concentrator of Mount Isa Mines to produce a product P80 as fine as seven microns. The objective was better liberation of galena and sphalerite. The IsaMill commissioning was completed by the end of 1999. The six new IsaMills were running to the metallurgical specifications almost immediately after start-up. This paper reports the performance of the George Fisher IsaMills in the zinc circuits and some of the latest development in the IsaMill designs and maintenance during George Fisher commissioning.

Jan 1, 2000

By M. Pelser, C Aldrich

"The presence of calcium and magnesium in the hydrometallurgical processing of base metals, results in a number of process difficulties. These problems range from the contamination of the final product (where the final product is a precipitate) to high energy consumptions and large bleed streams during electrowinning. Calcium poses an additional problem in sulphate solutions owing to the low solubility of its sulphate salts. This can easily lead to a process stream that is supersaturated with calcium sulphate, resulting in unwanted solids formation within the process equipment.Several processes are reviewed for the control of calcium and magnesium. Of these, fluoride precipitation was selected for experimental investigation. This method involves the addition of a soluble fluoride to precipitate CaF2 and MgF2. The experiments showed high selectivity for calcium and magnesium over the base metals. The experiments also showed magnesium precipitation to dominate for calcium to magnesium molar ratios greater than 1:3.To avoid the domination of magnesium precipitation, a flow sheet is proposed whereby only a portion of the base metal stream is subjected to fluoride precipitation. For the precipitation, a 10% excess of ammonium fluoride is used to remove the maximum amount of calcium and magnesium. After precipitation and solid-liquid separation the split-stream is returned to reduce the overall calcium and magnesium concentration of the base metal stream."

Jan 1, 2003

By Elmer Pabel Huayna Peraltilla

El proceso de lixiviación es un método para el tratamiento de minerales sulfuros y sulfuros mixtos que consiste en la utilización de un consorcio microbiano acidófilo y una solución rica en cloruro de sodio. En ese sentido, el presente texto destaca el método de la biolixiviación como la alternativa adecuada -en tanto solución ácida (cobre) que contiene el metal en su forma soluble. Dicho proceso se desarrolla en dos etapas: En la primera se usa una solución de cloruro de sodio, el compuesto protector, más un inóculo del consorcio microbiano. La mezcla permite obtener una recuperación de cobre de hasta un 80% basados en pruebas preeliminares. En la segunda etapa, se le agrega un agente oxidante, que no daña a las bacterias, con el fin de disminuir la pasivación del mineral y un inóculo fresco del consorcio y así prolongar la recuperación.

Sep 1, 2013

By G. Lee, E. T. C. Spooner

"Molybdenum mineralization at Boss Mountain is hosted by the Triassic Takomkane quartz monzodiorite batholith and is associated with a Cretaceous monzogranite stock. Ore has been mined from a sheeted vein system that describes a partial annulus centred upon the apical region of the stock and from subvertical breccia pipes that emanate from the stock. Molybdenite precipitation is coincident with CO2 effervescence from a dilute (1.9 mole o/o NaC/ equivalent) hydrothermal fluid over a temperature range of 250°C to 370°C at a pressure of approximately 350 bars, interpreted to be greater than or equal to the lithostatic load and equivalent to a depth of 1.3 km or less.IntroductionThe chemical and thermal constraints on molybdenum transport and deposition to form molybdenum ore deposits are not well understood. To address this problem, the Boss Mountain mine in central British Columbia, operated by Noranda Mines Ltd., was chosen as a well-described (Soregaroli and Nelson, 1976), relatively small and simple example of a Cordilleran Mo~ deposit. It is situated on the northeast slope of Takornkane Mountain, 10 km west of the community of Hendrix Lake (N.T.S. 93A/2W; latitude 52°06'N, longtitude 120°56'W). Access is from 100 Mile House by nearly 90 km of road, the first 50 km of which are paved."

Jan 1, 1995

By W. E. Bardelmeier

The high speed conveyor type self unloading bulk carrier concept has been around for about 70 years. Although the design was developed, refined and steadily improved in the Great Lakes, to date limited numbers of such vessels have emerged in the bulk ocean trades, and these have tended to concentrate within specific mineral trades. For example, North American gypsum companies have embraced conveyor self unloaders to the point where such vessels almost exclusively carry the gypsum requirements of this part of the world. One major aluminum company has developed an impressive fleet capability in self unloaders. Application of other ships tends to be fragmented through several mineral trades. A few years ago a new phenomonen began to appear on the Great Lakes. Whereas it had historically been accepted in that region that self unloaders were effective vessels for the minor bulk trades including limestone, coal, salt, gravel and sand; they had seldom been employed heavily in the big volume iron ore trades. Suddenly, however, the new generation of 60,000 ton Lakers which emerged were all designed as high speed self unloaders. The new vessels intended to trade especially in ore, or alternatively especially in coal, have somewhat different internal features, but the important point is that all are self unloaders.

Jan 1, 1979

By Jorge Injoque Espinoza

El presente trabajo describe la mineralogía de la plata, cobalto, níquel y oro en los principales depósitos de cobre y hierro de la faja costera. Para la descripción de los depósitos se revisan los trabajos de Injoque, así como en diversos estudios de mineragrafía, microsonda y geoquímica.

Nov 1, 1985

By G. V. Theja, V. B. Maji

Large infrastructure projects like tunnel excavations, underground constructions face innumerable risks. For successful completion of these projects, it is essential that we foresee and understand risks that could occur during different phases of the project. One of the risks affecting underground excavation projects is the inaccurate performance prediction of TBMs. As this could severely affect the project, resulting in lower advance rates and could also result in changing the excavation machine or method, due to difficulties in excavation, thereby increasing the overall cost of tunnelling. This makes performance prediction of the TBMs as one of the crucial aspects in tunnelling, as a precise estimation of its performance is required for planning and estimation of time and cost of the tunnelling projects. This performance prediction of TBM is a challenging geotechnical problem that is intricate and complex in nature, this is possibly due to the fact that TBM performance prediction involves understanding the rock fragmentation process in wide range from micro-scale (i.e. the interaction of surface of rock material and cutter tip) to macro-scale (including the interaction of rock mass and TBM). Thus in order for the performance prediction model to be efficient, parameters of both TBM specifications and ground conditions have to be considered. Various models have been proposed by researchers since the early phases of TBM application, these studies resulted in the development and improvement of numerous penetration prediction models. Most of these models consider the geotechnical parameters that are input to the model to be consistent along the TBM drive and neglect the uncertainties in parameters that occur. And so to improve the predictive capability of these models and to incorporate the above uncertainties, the penetration rate is modeled as a stochastic variable depending on the geotechnical and TBM parameters, its statistical distribution is determined and is used to characterize the penetration rate instead.

Jan 1, 2015

By C J. Greet, S Jacques

In most instances, the application of high-chrome grinding media results in an increase in the recovery of the valuable mineral(s). The authors have published data from a number of plant-based case studies, which indicate that it is not unreasonable to expect a recovery increase in the vicinity of 1.5 to 2.0 per cent for a copper ore. It is of interest to understand where the increase in recovery is coming from. That is, is the additional copper recovery the result of improved fine particle flotation or is it due to an improvement across all size fractions?This paper aims to answer this question. Laboratory flotation tests were completed using forged steel and a high-chrome alloy on a volcanogenic massive sulfide copper ore. The unsized data indicated that the application of high-chrome grinding media to this ore resulted in an improvement in both copper recovery and copper concentrate grade. A detailed kinetic analysis of both the copper sulfide and gangue minerals was completed that clearly shows that the change to a more inert grinding media produced significant increases in the flotation rate constants (both fast and slow) across all size fractions. It is also possible to observe that the change in pulp chemistry has resulted in a decrease in the flotation kinetics of the -20 micron pyrite, while the coarse pyrite recoveries have increased, presumably because of an increase in the flotation of the chalcopyrite/pyrite composite particles.CITATION:Greet, C J, Jacques, S and Kinal, J, 2014. Recovery-by-size kinetic analysis to determine where metallurgical improvements occur when converting to high-chrome grinding media, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By G. Wang, L. R. Moore, Y. Xiong, J. Gu

"Quartz is the second most abundant mineral in the earth’s crust. Not only does quartz have many valuable industrial applications, it is also one of the most concentrated gangue minerals encountered in the processing of other minerals. Minerals such as hematite, apatite, calcite, feldspar, barite, and many more. Numerous applications of industrial minerals are sensitive to the hardness and abrasiveness encountered with quartz minerals, while other applications may lead to processing challenges for the end user. Therefore, process and chemistry optimization must be applied to ensure optimal grade is obtained for these valued industrial minerals. Extensive studies have been conducted in processing various industrial minerals, thus achieving a range of quality specifications, which entailed the application of ArrMaz’s CustoFloat and CustAmine collectors towards the separation of quartz from other minerals. INTRODUCTION Industrial minerals often have the misfortune of the gangue mineral being very similar in surface charge, and coordination properties, to that of the mineral of interest. An example is seen in phosphate beneficiation, when dolomite can be a gangue minerals (Table 1). Therefore, the development of processing reagents are quite complicated. Some minerals, like clays, may be washed away. However, most require the manipulation of the pH, in efforts to fine tune the system to the narrow difference in isoelectric points of the different minerals, as well as the knowledge, and resources that are necessary to exploit the differences to yield and an optimal grade/recovery. In some cases, the application of a depressant may be required, such as the phosphoric acid commonly applied to achieve the optimal balance of grade/recovery for phosphate from a mineral with elevated concentrations of dolomite (Wang, 2016), or the application of hydrofluoric acid to assist in producing feldspar product from a mineral rich in quartz (Heyes, 2012).ArrMaz's CustoFloat and CustAmine product lines have successfully been applied to the processing of industrial minerals for more than 50 years. Applications include, but not limited to phosphate, sand (glass, foundry & high purity quartz), clays (feldspar, kaolin, etc.), and many carbonaceous and sulfate minerals. The successes of these 50 years are largely due to ArrMaz's ability to tailor make the processing chemistries to fit the ever changing and declining mineral feed grade and variations in water quality (Moore, 2015; Moore, 2016). This technical knowledge of mineral processing is strongly complimented by the intimate service programs in place at many of the beneficiation plants."

Jan 1, 2018

By M. N. Vu, G. Armand, A. Noiret, D. Seyedi

Extensive experimental observations have been performed around drifts and shafts at the Meuse Haute-Marne (North-Eastern France) Underground Research Laboratory (URL) to assess the extent and pattern of the induced fracture networks in Callovo-Oxfordian claystone. Two types of fractures can be distinguished, namely; shear (mode II) and extension unloading (mode I) fractures. The main goal of the present paper is to provide insights on the extent of damaged zone around the drifts by numerical simulations. A two-step approach is considered. First, 2D elastic calculations are performed for simulating the excavation of a drift following the direction of the major in situ horizontal stress. The evolution of the stress and strain tensors around drifts are calculated by applying an elliptic convergence function on the drift wall. Two failure criteria are then verified for the induced damage. An equivalent strain and an elastic energy based damage criteria are considered. The obtained results show that the employed simplified approach provides rather good results for the extent of the damaged zone for drifts parallel to major horizontal stress. However, post-processing elastic results leads to overestimating the vertical extent of the damage zone and underestimating its lateral extent, where the in situ stress state is quasi-isotropic in a section of drift. Nevertheless, the obtained results show that an energy based damage criterion could be considered as a potential way for reproducing the extent of the damaged zones if a convergence function can be defined for the drift.

Jan 1, 2015

By T. F. Dumm, L. G. Austin

"INTRODUCTIONGomez and Austin (1,2) have recently described calibration procedures for quantitative chemical analysis of particles by energy dispersive spectroscopy using particles mounted and polished in a resin matrix and scanned by an SEM under computer control. Their software is specifically designed for the analysis of Si, Al, Ca, Na, K, Fe and S in coal particles, and in this case the resin is loaded with iodine (3) to enable the exposed cross-section of an embedded coal particle to be differentiated from the matrix. However, the basic ideas of their procedures could be extended to any system of particles where it is desired to measure inorganic species in particles containing light elements such 0, C, H and N which are not directly detected. In these circumstances it is necessary to perform a quantitative determination of the measured components, so that the equivalent volume of light elements in the excited sample volume can be estimated by difference using ZAF and other corrections applied to the raw count intensities.Part of their procedure involves a new technique (2) for estimating background spectrum intensities; the intensity for a particular energy window is then subtracted from the total measured intensity for that window to enable the concentration of the corresponding element to be calculated. In addition, corrections for overlap of peak spectrums are applied. For example, Figure 1 shows some typical spectrums for known materials for the system they used, demonstrating a wide Gaussian spread about the theoretical peak energy. Since background spectrum and peak overlap corrections require a knowledge of the composition of the material, as does the application of the ZAF corrections, it is necessary to have an iterative solution of the equation sets, starting with estimates of the composition based on initial count rate corrected solely for dead time and detector efficiency."

Jan 1, 1989

By M. E. Bilir

In this paper, we review cases in which dramatic and visual swelling problems are experienced in underground structures. Swelling rocks have caused many problems in underground engineering projects. They pose severe problems to the design, construction and maintenance of underground openings. If an appropriate integrated design procedure, which proceeds from exploration, tests, analyses and realistic assumptions of swelling behavior, is used during the design stage, the execution of the project can be completed without any serious delays or dramatic design changes. The case histories were subdivided into three classes that include tunnels, underground coal mines and others. For the evaluation of cases, the surrounding rocks, swelling minerals, water inflow, swelling test results and swelling problems were considered. The main purpose of this review is to inform the reader about potential problems with swelling phenomenon and to emphasize the rehabilitation and extensive cost which are encountered due to the lack of necessary integrated design approaches.

Aug 1, 2013

By Brian E. Perrine

Underground mining requires a variety of specialized equipment. With ever-changing mining conditions and methods, some mines have had to resort to purchasing existing industrial equipment and adapting it for underground use. Since this equipment is not made for underground mining or their specific task, the result is often lost time, money, and sometimes an unsafe working condition. One such application is the setting of a CAN. A CAN is a type of cylindrical secondary roof support made from a cement composite and encased in steel. The CAN has become popular because of its simple one-piece design that can handle heaving and sagging better than other available designs. ?Because of this exceptional ability to sustain load through extended convergence and displacement, the CAN is one of the most robust and stable standing supports in use today.?It also promotes better air flow due to the size and shape of the CAN. CAN size and weight have increased over time to handle more difficult mining conditions. Significant down time and inefficiencies with existing CAN setting machines at Twentymile Coal were directly due to the item in use not being designed to be task-specific. They were undersized with very limited movement. The miners had to take extra steps and precautions when setting CANs. Maintenance delays were significant. Twentymile Coal Company realized that they required a safer, more reliable and more efficient machine to handle and set CANs, and looked for a partner to develop a new design-specific machine. They worked jointly with J.H. Fletcher® engineering and sales to design and manufacture a machine specifically made for setting CANs. The objective was to produce a machine that would handle the conditions and methods that the mine required for setting CANs during longwall retreat. The resulting design had to be safe, stable, have a wide range of motion, be ergonomic, simple to use, and easy to maintain. The machine also had to improve efficiency. The resulting machine has been operating for approximately one year at Twentymile Coal and has been proven to improve safety, reliability, and efficiency. In conclusion, with the task-specific CAN Manipulator, the mine is able to better plan daily tasks with the knowledge that the machine will be available throughout a shift, and the employees will be safer because of the machine?s ergonomics, stability and safety. This has resulted in better productivity and a safer environment.

Jan 1, 2013

By M. P. Neira

In-situ leaching of copper from chalcocite relies on ferric iron concentration in the lixiviant being reduced to ferrous. To re-establish the ferric concentration in solution, ferrous must be re-oxidized. This reaction is slow under normal chemical conditions but it is catalyzed by Thiobacillus ferrooxidans bacteria. BHP Copper's Miami In-situ unit developed a bio-reactor as a method of oxidizing ferrous to ferric. The effects on oxidation of temperature, CO2? oxygen, and air injection flowrate were defined. This paper summarizes the results of ferrous bio-oxidation using plastic column packing and oxide ores as bio-reactors and the leaching results of the bio-reacted lixiviant on chalcocite ores.

Jan 1, 1997

By Paul H. Muller

The configuration of remote seal DP cells for specific gravity measurement is described and the calculations for calibration are presented. The error induced by ambient temperature change is investigated as it relates to capillary dynamics and electronic considerations. Instrument specifications are discussed in the light of accuracy requirements and the calculation of error vs. ambient temperature is described.

Jan 1, 1984

By J. L. Feng, F. Zhang, S. K. Hu

"Cracking is one of the most serious damages in tunnel linings, which is often observed by in-situ inspection to tunnel engineering. It is difficult to better characterise for the deformations from continua to discontinua by the traditional continuum mechanics due to emerging of crack initiation, crack propagation, and coalescence, at several scales. In this paper, the process of failure that was from micro damage to macro crack in concrete tunnel linings under experimental load conditions, was quantitatively simulated by the combined finite-discrete element method (FDEM). Comparison of the simulating results with that obtained by the full-scale test of concrete lining under different loading conditions in the literature was respectively good agreed and shows that such FDEM technique is appropriate to model the continuousdiscontinuous problems. The present study indicates that the FDEM technique could be benefit to quantitatively evaluate the stability and damage level of tunnel lining system. INTRODUCTIONMost damage to tunnel linings is caused during the construction phase, which can emerge in a form of single macro cracks or even large-scale spalling. The cause of such damage is mostly the occurrence of, either impermissibly large contact stresses resulting from high thrust loads combined with production and installation tolerances in the segments resulting in a geometrical lack of fit (Maidl et al., 2012; Transportation Research Board, Basic Research and Emerging Technologies Related to Concrete Committee, 2006), or unallowable tensile/shear stresses appearing in the tunnel linings under complicated loading conditions (Ansell, 2010). Such a macro failure phenomenon may also be regarded to as a result of growth, coalescence, initiation of microcracks in tunnel linings due to the complicated loading action, and even potentially lead to an instability or collapse of the local or entire tunnel system. Much work has been devoted to investigate for the characters of micro and macro cracks, the influence factors of damage patterns, the settlement of a tunnel, the width, length and density of lining cracks, especially from classifiedly and qualitatively (Wang, 2010; Huang et al., 2013). However, the safety evaluation of tunnel is definitely required to not only inspect in situ, but further also quantify computing and analyzing for tunnel lining systems, so as to provide a global viewpoint of process of the tunnel deformation, which aims to help for subsequent decisions, e.g. controlling traffic flow or immediately repairing task. Additionally, the design of lining thickness and its structural analysis that is mostly determined by previous experience and similar construction examples is also needed to be improved."

Jan 1, 2015

By M Paakkunainen

Sampling is often the most critical part in process analysis. When the mean of a continuous lot, such as a process stream within a given time interval, is estimated by calculating the mean of several samples, the uncertainty of the estimated mean depends usually on the sampling strategy. Three different strategies can be used: systematic, stratified or random sample selection. The standard deviation of the lot mean is different for these methods so that systematic sampling usually gives the smallest and random sampling the largest standard deviation. Pierre Gy developed a method where the sampling errors of one-dimensional lots for these three strategies can be estimated from a variogram, which is calculated from a variographic experiment, ie from a set of one-dimensional time series measurements with fixed sampling interval. While variogram is an excellent tool for characterising and displaying the variability of autocorrelated processes as function of time, the sampling error estimation from it is quite laborious, however. In this work an alternative method for estimating the sampling errors was developed. The process is divided into strata of equal sizes, varying the length of strata similarly to variographic analysis. For stratified sampling the standard deviation estimates are obtained by analysis of variance and for systematic sampling by fitting a linear regression line to each stratum and calculating the residual variances. By pooling the individual variance estimates the variance estimates that are corrected for autocorrelation are obtained. The new method was tested with simulated and real data sets having periodic, random and/or drift fluctuations. For stationary processes the results agreed well with the results of the GyÆs variographic method. The method can probably be generalised to estimate the sampling variance of higher-dimensional lots.

Jan 1, 2005

By R. Pixler

Arch Mineral Corporation and Rocky Mountain Energy's Medicine Bow Mine in Wyoming presented an interesting challenge to the concept of mining a multiple-seam, dipping coal in the Hanna Basin. The 3362 and 2962 pits at MBCC were designed in a multiple seam coal consisting of 4 (and in some areas 5) bands of coal; these coal beds are all in the Ferris formation. The area was subject to some localized faulting and a major fault caused a physical restraint that we mined up against in our final cut. Using a 1570 dragline as the principal stripping machine, the concept of developing a bench for stripping the lower seams from the low-wall side of the pit was initiated. The results of this method of stripping were very satisfying for this pit through the completion of pit life and prompted us to use it in other areas at MBCC and at our other operations. Mining a dipping coal presents a small twist to conventional "flat" coal stripping. The spoil has a tendency to continually try to slide into the pit and the increased overburden on each cut as you mine down the dip creates spoil problems unless adequate design provisions are made prior to stripping.

Jan 1, 1986

By W. Fletcher

Startup of a new plant is a very interesting time. It generally is also a very demanding and often frustrating period. Startup problems can become serious ii they impede the early achievement of full plant production. Raw materials are wasted, manpower is unproductive, field modifications can be extremely expensive and market commitments may not be met. This paper outlines a well proven and highly successful approach to eliminating many of the problems and frustrations often experienced in plant startup. The procedures and methods summarized in the following paragraphs have been developed over a period of 25 years during which some 90 plants were started up.

Jan 1, 1981