Search Documents

By Luis Bergh, Juan Yianatos, Luis Vinnett

"Process automation as an engineering discipline is more than control systems since it includes industrial instrumentation, such as sensors, transmitters and actuators, as well as control and supervision systems, collection and transmission of data and real-time software applications to supervise and control the operation of plants or industrial processes. In the last several decades, accelerated technological development has provided a variety of software and hardware tools to aid development, maintenance and continuous improvement of automated systems. These developments however seldom reach their full potential in real plants. There are many factors to be considered, among them human capital specific training and the organization model. In this paper, a methodology for training engineers in advanced control and supervision of flotation plants is presented based on study of the application of these technologies in hybrid pilot plants. Since experimentation in real plants may present undesirable risks and costs, and simulation studies are usually limited to some unrealistic conditions, a laboratory where on-line measurements of the hydrodynamic behaviour of a pilot plant is mixed with phenomenological models has been created. In this form, an environment as close as possible to a real plant can be recreated. A flotation column and a circuit of three pneumatic cells are fully instrumented and connected to a PLC and PC network. In the control room, students learn applications of classical PID control in a DCS environment, advanced predictive control, on-line process operation diagnosis, fault analysis, virtual sensors and expert-fuzzy systems. Several undergraduate and graduate courses and theses are supported by this Process Control Laboratory infrastructure. Examples of these applications are discussed."

Jan 1, 2014

By A. Demirag, F. Burat

"The most important metals in the jewelry sector are undoubtedly gold and silver. As a result of workmanship work done in the jewelry industry, the tiny metal and jewel fragments and metallic powders are scattered. Given the prices of gold and silver on the market, the dust that emanates from these workshops is of great importance. Gold recycling has become as important as raw material production within the mass market and gold production industry. In 2016, 29% of the world gold supply has been obtained through recycled gold production. Waste derived from jewelry activity is included in this category, and represents an essential component of this percentage. In the scope of this study, the recovery possibilities of Au and Ag from jewelry sweeps floor sample was investigated using flotation method. In the experiments, optimum pH value, particle size, the effect of dispersant, type and amount of reagent were investigated. As a result of these studies, it was determined that the optimum pH value was 6.5 and the particle size was -212 microns. It was observed that the most suitable reactive combination was Aero 242 and Aerophine 3418A and Na2SiO3 has no positive effect on recovery of Au and Ag as a dispersant agent. As a result of tests, a final concentrate containing 268 ppm Au and 2122 ppm Ag was obtained with 81.4% and 74.5% recovery respectively. INTRODUCTION Because of the softness of pure gold, it is usually alloyed with base metals for use in jewelry, altering its hardness and ductility, melting point, color and other properties. On the other hand, gold has some special chemical properties which in normal conditions, don’t react with water, dry or humid air, oxygen, ozone, nitrogen, hydrogen, fluorine, iodine, sulfur and hydrogen. In these days, gold is used in different sectors like jewelry, electronics, finances and investing, dentistry, medicine, aerospace, awards & status symbols. According to Deutsche Bank Research, the primary usage of gold is jewelry. It has been used to make ornament and jewelry for thousands of years. In this sector craftsmen learned that alloying gold with other metals like copper, platinum and silver to increase gold’s durability. Alloying gold with other metals changes the color of the products. Another significant sector of gold is electronics. Modern electronics want the use of noble metals, like gold, especially in the areas of information processing, telecommunications, and military and space electronics (Habashi, 1997). Electronic devices use very low voltages and currents which are easily interrupted by corrosion or tarnish at the contact points. Gold is the highly efficient conductor that can carry these tiny currents and remain free of corrosion. Electronic components made with gold are highly reliable. Gold is used in connectors, switch and relay contacts, soldered joints and connecting wires. Every sophisticated electronic device have a considerable amount of gold. This includes cell phones, calculators, personal digital assistants, GPS units, and other small electronic devices. Most large electronic appliances such as television sets also contain gold. Humankind has known silver since prehistoric times like gold because silver occurs in native form. The metal is found in the Earth's crust in the pure, free elemental form native, as an alloy with gold and other metals, and in mineral such as argentite. Most silver is produced as a byproduct of copper, gold, lead, and zinc refining. Silver is very soft metal like gold also, it is the highest electrical conductivity, thermal conductivity, and the lowest electrical contact resistance of all metals (Habashi, 1997). Silver is used in different sectors like industry, jewelry, electronics, photography silver good, and coins. The main usage of silver is supplied by electronics. Silver's unsurpassed thermal and electrical conductivity among metals means it cannot easily be replaced by cheaper materials. In addition to silver is using in ener"

Jan 1, 2018

By Richard L. Profio

A practical analysis of the three basic elements of a mining shovel's productive capacity. Payload Speed Reliability Improved dipper fill factor is explored referring to the latest generation of wide dippers combined with higher "bank horsepower" capabilities of modern drive systems. Cycle time improvement is reviewed including overall attachment geometry and coordination of motions. A specific case study is detailed. Basic reliability of welded structures, machinery components, and electrical systems are related to operating costs. Three basic elements determine a mining shovel's long term productive capacity: 1) Average payload per cycle. 2) Average cycle time; and 3) Reliability. This paper deals with productivity gains that are possible with existing shovels as well as new equipment.

Jan 1, 1984

By D W. Nisbet

Today Hudson Bay Mining and SmeltingÆs 777 Project is the largest mining construction project under way in Canada. The project comprises six components: construction of the new 777 zinc-copper mine; construction of the new Chisel North zinc mine that will truck ore out from 600 metres below surface; expansion of the Flin Flon ore concentrator; expansion of the zinc plant to increase throughput by 15 per cent; a spill gas project that will reduce fugitive gas emissions by some 90 per cent; and infrastructure improvements including construction of a new electrical substation. Total investment in The 777 Project is over $US 260 million. Seven years ago, the Flin Flon, Manitoba-based company was fighting for its very existence. How does a company go from down-for-the-count to robust contender in just seven years? Contributing reasons are many, but all have their root in a process HBMS calls æTransformationÆ. It is transformation that has taken HBMS, a very traditional company, through a very non-traditional turnaround (Figure 1).

Jan 1, 2000

By K. Heatwole, D. Shier, A. Davis, J. Kidder, S. Sunkavalli

"Acid rock drainage (ARD) is produced when sulfides are exposed to oxygen and water. Oxidation reactions typically result in a depression of pH and leaching of solutes and metals. Many oxidation models have been developed based on oxygen diffusion, but in environments with high permeability, other transport processes (i.e., convection and advection) can play an important role. Multiple sulfide mineral phases with differing oxidation rates should also be incorporated. WROC, a finite-difference model, was developed to account for these factors in predicting ARD. The program includes sulfide mineral oxidation using a shrinking core mechanism, heat transfer by conduction, heat of reaction and oxygen transport by diffusion and advection. The model was validated using data from the literature. After validation, the WROC model was used to simulate several different waste rock scenarios, including different forms of sulfide mineralization and the effect of implementing a waste rock cover. The results demonstrate that including specific sulfide mineral phases can have a significant effect on oxidation and that implementation of a cover can also aid in reducing waste rock oxidation.IntroductionAcid rock drainage (ARD) is a notable environmental concern in areas where rock or other material with acid generation potential is disturbed. ARD is defined as drainage that occurs as a result of sulfide oxidation in rock exposed to air and water. ARD is characterized by low pH, elevated metals concentration (especially aluminum, iron and manganese), sulfate and high total dissolved solids. The low-pH water that results from acid generation is capable of solubilizing heavy metals contained within the rock. The principal sulfide mineral in mine wastes is pyrite (FeS2). Pyrite oxidation is complex and can involve chemical and biological reactions. Oxidation of pyrite by atmospheric oxygen produces one mole of Fe2+, two moles of SO4 2- and two moles of H+ for every mole of pyrite oxidized, as described by Eq. (1)."

Jan 1, 2015

By A J. Burchell

The introduction reviews the tunnelling carried out in Singapore since the early 1980s. Between 1983 and 1990, Phases 1 and 2 of the mass rapid transit system were constructed. These included some 20 km of bored and cut and cover tunnels together with 18 underground stations. Some particular points of interest in this massive project are briefly commented upon. Reference is also made to other underground or underwater schemes undertaken during this period such as the proposed large caverns project and the submerged tunnel to Pulau Seraya. A description of the subsurface works, now under construction in Singapore, follows. This includes an all underground North-East railway line 20 km long with 16 stations. At a budget of US$ 3 billion, this is a major civil engineering undertaking. Another project is the extension of the railway to Changi Airport which involves 3.5 km of twin tube tunnelling together with a major underground station which is fully integrated into the airport terminals. An on-going program of further major railway extensions over the next 10 to 15 years is in place and an outline is given of some of the most important underground sectors. Other proposed projects such as the underground roads system and the deep level sewers are briefly described. Together they demonstrate the very significant volume of underground construction scheduled for the next century in Singapore.

Jan 1, 1999

By Baojun Zhao, Zhixiang Cui, Zhi Wang

"Bottom blown oxygen copper smelting process has been developed in Dongying, China by Dongying Fangyuan Nonferrous Metals Co., Ltd. in commercial scale. This is the first modem copper smelting technology developed in China with the advantages of high oxygen enrichment, low temperature and autothermal operation. Production capacity of more than 100,000 tonnes per year of copper has been achieved through a single bottom blown oxygen furnace with instantaneous feed rates reaching up to 90 t/h. The main features of the bottom blowing smelting process are that high grade matte (up to 72 wt% Cu) can be produced at relatively low temperatures with 2-3 wt% Cu remaining in the smelting slag. Analyses of quenched smelting slag show that significant amount of magnetite crystals are present in the slags at operating temperature which indicates that the operating temperature was much lower than the liquidus temperature of the slag. After four years operation this new technology has shown great potential for expanding production capability and energy saving. Process development continues on the first commercial scale bottom blown furnace at Dongying Fangyuan Nonferrous Metals and a larger bottom blown smelting furnace is under construction.IntroductionFlash and bath smelting technologies are the major processes used in modem copper making industry [l]. Ausmelt/Isasmelt using top blown and Noranda/Teniente using side blown are typical and common bath smelting technologies. In 1980s-1990s Hunan Shuikoshan Mineral Bureau, jointly with China Nonferrous Engineering and Research Institute (now China Enfi Engineering Corp.), developed the concepts of the bottom blown oxygen processes for both lead and copper smelting [2]. After the pilot test on 3000 ton copper per year scale in 1991, it was not progressed to industrial scope."

Jan 1, 2013

"Liberation is a key requirement for efficient separation in mineral processing. As a consequence of this an understanding of the inherent textural features of an ore is no longer possible since during the process of liberation, texture is destroyed. Knowledge of key textural features, such as mineral grain size and distribution, prior to breakage processes provides the opportunity to understand the textural drivers for ore hardness. Modern characterisation methods, including automated SEM-based techniques, provide the possibility of measuring mineral characteristics at a range of scales. This paper discusses how textural features of two different ore types in a porphyry copper deposit can be measured and interpreted at a number of scales. Standard breakage tests conducted on the ores indicate that one of the ores can be characterised as hard and the other as soft. The impact of mineral grain size and the presence and scale of vein type structures in the two ores have been used to determine the extent to which these features influence ore hardness.INTRODUCTIONIn order to effectively convert ore into metal, knowledge of both the processing stages and the characteristics of the ore are essential. Prior to the advent of technologies that enabled the fundamental understanding of the sub-process at each stage of processing and the measurement of appropriate ore properties the most effective way to understand how an ore would respond to a process was to put it through that process, for example the way to determine how an ore would break was to first break it. Existing comminution models seek to predict the size distribution of rock fragments as the result of applied energy based on knowledge of the rock strength. It is common for these models to consider the rock as homogeneous and despite providing important data for the design and optimisation of industrial comminution circuits these models are only applicable within a narrow range of operation. In order for reliable predictive models to be developed that account for the inherent ore characteristics, a step change is required in the type of measurements that are carried out to characterise an ore and the type of data that is extracted and used as model inputs."

Jan 1, 2016

By Richard Brink, Eric M. Klein, Kenneth B. Andromalos

"A portion of the roof for a 129 x 144-inch, nearly 100-year-old sewer outfall in the City of Baltimore had deteriorated to the point that it resulted in the development of a large sinkhole in a residential neighborhood. A subsequent video inspection of the sewer outfall indicated that there was a hole in the sewer outfall, and it would need to be repaired . After initial backfilling of the sinkhole and repairs to the water service lines, a conventional wood shoring system was used to support the excavation and expose the Main Outfall Sewer to inspect and repair it. This excavation was unsuccessful because of loose sandy soils and high groundwater conditions. An innovative use of a steel reinforced jet grout excavation support system was ultimately used to underpin an adjacent 20-inch water main and other nearby utilities, and provide access to the top of the Main Outfall Sewer some 22 feet below the street surface to facilitate inspection and repair of the sewer. This excavation support system was also successfully utilized in the final repair of the sewer roof by serving as a buttress for the new roof system.1.0 IntroductionThe project site is located in a residential neighborhood with brick masonry row houses situated on the south side of Chase Street and a brick masonry church on the north side of the street. Figure 1 illustrates the location of the site. The City right of way is 65 feet wide, and the street is 40 feet curb to curb. The centerline of the Main Outfall Sewer runs parallel to and a few feet south from the centerline of the street. Other utilities running parallel to the street include a cast iron 20-inch water line built about 1910, a 24-inch terra cotta storm drain, a 6-inch terra cotta sanitary sewer, a 4-inch cast iron gas line and a 40-inch electrical duct. Cross utilities included a 4-inch gas line and several smaller water and gas service lines to the church and row houses. One gas line that was not shown in the City's GIS database was exposed during the excavation."

Jan 1, 2005

By Valery Kaplan

Sulfur emission in the form of SO2 in flue gases is one of the most serious atmospheric pollutants associated with coal combustion and non-ferrous metals production. The carbonate eutectic method for removing SO2 from flue gases at 723–923 K was initially proposed in the 1970s but despite its great efficiency (SO2 concentration in the flue gas after purification reached 0.003 volume %), it could not be implemented by industry due to the complexity of the carbonate melt regeneration stage. Earlier we proposed a method suited to coal-firing power stations where the melt was regenerated using CO as a reducing agent. However, most metallurgical plants do not use coal and therefore lack a large source of CO. Here we propose a method for removing sulfur from the carbonate eutectic melt by purging it with natural gas or a natural gas/air mixture, which are available in the vast majority of metallurgical plants. This reaction leads to the reduction of sulfate to H2S gas that leaves the melt. The experiments we conducted show that nearly complete sulfur removal from the melt is possible at 823 K and that the reaction rate is sufficiently high for a large scale process. One can foresee that this carbonate melt-based SO2 removal technique may become a practical and economically attractive method for limiting sulfur emission to the atmosphere from non-ferrous metallurgical processing plants.

By A. W. Fletcher

Report of discussion at February, 1971, IMM general meeting (Chairman: M. J, Cahalan President) of a paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, December, 1970, pp. C247-52, and contributed remarks. Contributions are included from: Cahalan M.J., giving figures related to leaching Cu from pyrite at Rio Tinto 1880-1910; Noakes F.D.L.; Embling P.M.K.; Bradshaw A.V.; Le Roux N.W.; Kelly D.P.; and Tuovinen O.H. Questions were raised regarding impurity removal, effects of light and ultraviolet light on the bacteria, the economics of solvent extraction and the possibilities for other organisms or other metals

Dec 1, 1971

By R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corporation's Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about -502 without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1971

By Roberto Parra

The classic criteria of the preparation of the charge for the smelting of copper concentrates in a flash furnace considers the mass and energy balance from the chemical and mineralogy composition of the concentrates. The operation parameters fixed with this method don't assure the stability of the operation and the critical problems of the slag quality and dust formation occurs very often. This paper presents the results of a laboratory test that allows the predicition of the behavior of concentrates blends in the view of the minimization of the dust formation and the magnetite control in the slag. The combustion of different copper concentrates and blends were done in a drop tube furnace. The results show that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of 2 or 3 types of concentrates can be identified. From the reasonable hypothesis that the qualitative behavior of blends in the drop tube represents the real behavior in the burner, the preparation of the charge with this approach could help to solve those operational problems.

Jan 1, 2003

By J. Leon-Torres, D. M. Stefanescu, P. A. Curreri, S. Sen

"Experiments were performed under terrestrial gravity (lg) and during parabolic flights (10·2 g) to study the solidification and macrosegregation patterns of Al-Cu alloys. Alloys having 2% and 5% Cu were solidified against a chill at two different cooling rates. Microscopic and Electron Microprobe characterization was used to produce rnicrostructural and macrosegregation maps.In all cases positive segregation occurred next to the chill because of the shrinkage flow, as expected. This positive segregation was higher in the low-g samples, apparently because of the higher heat transfer coefficient.A 2-D computational model was used to explain the experimental results. The continuum formulation was employed to describe the macroscopic transports of mass, energy, and momentum, associated with the solidification phenomena, for a two-phase system. The model considers that liquid flow is driven by thermal and solutal buoyancy, and by solidification shrinkage. The solidification event was divided into two stages. In the first one, the liquid containing freely moving equiaxed grains was described through the relative viscosity concept. In the second stage, when a fixed dendritic network was formed after dendritic coherency, the mushy zone was treated as a porous medium.The macrosegregation maps and the cooling curves obtained during experiments were used for validation of the solidification and segregation model. The model can explain the solidification and macrosegregation patterns and the differences between low- and high-gravity results."

Jan 1, 1999

By J. M. Janssens, Van Quach Tinh, M. Ruel, R. Leblanc

"Microscopic studies of peat moss indicate a highly porous material. In view of using this natural product as an adsorbing agent for the treatment of polluted water, studies of its adsorbing power for beef extract and alkyl benzene sulphonate solution were determined. The effects of time of contact, particle size, concentration of adsorbent and concentration of pollutant were studied. In the case of beef extract, there is a COD reduction of around 27 per cent; in the case of the alkyl benzene sulphonate, the percentage reduction varied from 72 to 95 per cent. A water treatment plant based on the adsorbing power of peat moss with simultaneous recuperation of the pollutant is proposed."

Jan 1, 1971

By R Bartlett

Process engineering-science originally developed for percolation leaching of ore in heaps is extended to the decontamination of unsaturated soil, either in situ or after excavation and emplacement as a soil heap on an impervious pad. Phenomena considered include: soil matrix porosity and permeability; percolating solution retention, capillarity and flow; washing sweep efficiency; optimum solution application rates during leaching; soil agglomeration to improve soil permeability and soluble contaminant transport by diffusion in soil agglomerates. Practical aspects briefly discussed include leach pad construction, solution distribution and recovery from the soil, and solution containment.

Jan 1, 1994

By L Köresaar, J Moilanen

With lower and increasingly variable Fe grades in iron ore resources, the monitoring of Si, Al, Mg and other light elements to meet quality requirements is gaining importance in the iron ore beneficiation industry. The high cost per manual assay and associated manpower requirements often limit the frequency of shift composite samples and laboratory assays. Furthermore, the shift composite assays represent past performance of a plant but are not useful for immediate reactions to feed variations, detection of equipment malfunctions or process control. Automated online analysis of light elements radically reduces the cost per assay and provides repeatable, timely data for process analysis, control and optimisation.A light element online slurry analyser, based on laser-induced breakdown spectroscopy (LIBS) optical emission technique, will be presented. This paper discusses the analyser design for the iron ore industry and also reviews the performance of the analyser against the manual laboratory. Additionally operator safety, user friendliness and maintenance requirements are discussed.A case study will also be discussed in this paper. The sophisticated measurement technique has been implemented in an industrial automated analyser and sampling system to allow for slurry measurement for up to 12 sampling points. However, careful selection of the sampling points and implementation of the sampling system is required for smooth operation.CITATION:Köresaar, L, Timperi, J and Moilanen, J, 2015. Optimised process control in iron ore via online analysis of light elements, in Proceedings Iron Ore 2015, pp 511–518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Jean M. Kenney

Frequencies of haulage-related accidents in metal and nonmetal surface mines for the years 1988 through 1990 were investigated and compared with those of non-haulage-related accidents. This study was part of the U.S. Bureau of Mines program to improve mining haulage safety. Data were obtained through the U.S. Bureau of Mines Accident Data Analysis (ADA) program. The chi-square test was used to compare frequencies of haulage-related and non-haulage-related accidents for each of the following variables: degree of injury, age, total number of years of mining experience, and shift time. Significance was determined for degree of injury between haulage-related and non-haulage-related accidents. Age of injured did not vary significantly between haulage-related and non-haulage-related accidents, but total number of years of mining experience was found to be significant. Shift time for the accident proved to vary significantly between haulage-and non-haulage-related accidents. Events causing injury for haulage-related accidents were tabulated, and the most frequent determinants of haulage-related accidents were identified. Accident descriptions for both fatalities and permanent disabilities were studied, and the primary causes of these accidents were identified. These findings suggest that haulage-related jobs are among the most dangerous when considering accidents experienced by all workers in the metal and nonmetal surface mining work force.

Jan 1, 1993

By A. O. Dufresne

WITHOUT transportation, mining would be quite impossible. Any person familiar with the operation of a mine knows full well that from the minute ore is blasted, it is kept moving until it reaches the treatment plant. In the mill, by means of conveyors and elevators, the ore is brought from receiving bins to one machine after another until finally its valuable mineral is separated from the gangue. The finished product must then be shipped -either by boat, rail, or motor trucks to industrial centres, where it undergoes further treatment and transformation into finished commercial goods. Everybody appreciates that the winning of an or-e includes, amongst various operations, the moving of large quantities of material of generally low value. Transportation, therefore, must be considered One of the most important factors in the economics of mining. My assignment, this afternoon, is not to treat of that phase of transportation as it directly affects mining operations, but rather to consider some of the aspects of overland transportation and its influence in bringing about the development of mining camps in Canada. I shall take the liberty of rapidly surveying conditions facing prospectors, mine developers and operators from the time a region is still in a pre-pioneering stage until such time as a mine starts shipping its concentrates.

Jan 1, 1956

By D. Hinton, M. McCawley, R. C. Lantz, F. Pisano, C. Stanley

"INTRODUCTION Aerosols (5 um have not been shown to be consistently generated and characterized in inhalation chambers. Particle deposition in the lungs however may occur with particles as large as 25 um(1). Therefore, in order to closely simulate the atmosphere of an underground coal mine where the distribution is bimodal, with modes at S and 15 um (2), particles much greater than <1 um must be characterized for uniform mixing and size distribution within these chambers. The Hazelton Animal Exposure Chamber has been chosen because it has been best characterized for smaller particles (<1 um) (3), and is the major type used by most inhalation toxicology institutes such as Lovelace Inhalation Toxicology Institute and Battelle Northwest Laboratory.BACKGROUNDPreviously published studies on the inhalation of solid aerosols have attempted to characterize the distrition of particles of <2 um in diameter. There are no published reports of extensive work characterizing either the size distribution of particles <1 um or the concentration throughout the exposure chamber (Table 1).Table 1 shows the variability and sizes of several aerosols <1 um in diameter used in five previous chamber studies.Discussion of Previous StudiesThe study done by Bauermash, Bryan, Dickinson, and Burke (4)stated two major concerns in the development of the 6.5 ft. diameter chamber. The first was that a quantity of animals could be exposed to the same concentration regardless of the location of the animal, and second was that the chamber could be easily cleaned and decontaminated. The solution to the first concern required a circular chamber with the contamination air entering the chamber somewhere along the central axis. The animals could then be changed during exposure time so that each animal was exposed throughout the total volume."

Jun 1, 1988