Search Documents

By J. Iannicelli

An entirely new level of magnetic filtration technology was put into full commercial production by the kaolin industry of Georgia, U.S.A. during 1973-1974. At present, four kaolin producers in Georgia are operating large magnetic filters each capable of processing over 1000 gallons of kaolin slurry per minute or over 65 tons of kaolin per hour on a dry basis. A fifth large filter will go on stream in August, 1975. Four of these units are 84" machines manufactured by the Pacific Electric Motor Company of Oakland, California. When operated at the maximum 1000 g, p. m. rate, these five large magnetic filters have a combined capacity approximating the entire waterwashed coating and filler kaolin produced in the U.S.

Jan 1, 1976

By Andrew B. Cecala

As deeper seams are continually mined, methane liberation will continue to increase and must be monitored effectively. To effectively monitor and develop appropriate control technology, methane-liberation patterns must be known. The Bureau of Mines recently completed a study to identify specific patterns of face methane liberation during long- wall mining. Both of the longwall faces surveyed had high methane liberation rates. At one longwall face, most of the methane was liberated during cutting of coal by the shearer mining machine. At the second face, a significant portion of methane was emitted from the face and floor. An effective methane-monitoring system would be different for each longwall panel because of the differences in how the gas is released along the face.

Jan 1, 1985

By A. M. Amdur, A. N. Matushkina, G. I. Gazaleeva

"The article highlights results of theoretical and practical studies on the enlargement of fine gold in the process of heat treatment. The object of research is refractory gold silicate-carbonate ores of Vorontsovskoe Deposit (Northern Ural), containing fine gold. For setting up experiments and analyzing the results were used the methods of applied mathematics, mathematical statistics, mathematical and physical modeling. Modeling and calculations were performed using the software package HSC Chemistry 6.0, MatLab, setting up a full factorial experiment and other modern modeling methods. Using a scanning electron microscope, the distribution of fine-dispersed ore gold particles by size was studied. It was found that gold particles smaller than 0,4 µm smoothed the vertices and edges, i.e. they are of globules with an amorphous structure. Amorphous materials are nonequilibrium phases with high thermodynamic activity. The physicochemical properties such as melting temperature, diffusion coefficients, the content of metal impurities differ from the properties of the solid phases. In the course of the research were formulated the following scientific bases of the mechanism of enlargement of the gold particles: - the movement of dispersed droplets of gold in the process of external heat to the surface of the ore particles in the pore occurs under the action of thermocapillary pressure; - after melting of the host rock occurs flotation of molten droplets by the bubbles of gases and coagulation of fine gold; - the conditions of flotation drops of gold in oxide melts; floated drops of radius R = 1-100 µm. Analysis of the equilibrium at the perimeter of wetting a drop of gold-oxide melt-gas showed that the scheme of the tension will not significantly differ from the case of solid gold, while the radius of the gas bubbles should be at least 2 times greater than the radius of drops of gold. The proposed method of predicting the results of the enrichment of the proposed scheme, including heat treatment and gravitational centrifugal concentration of crushed ore. Experimental verification of the proposed scheme in the laboratory showed a satisfactory convergence of experiment and prediction. Gold recovery in the concentrate was 33,84 against 33,7 percent forecast. The increase in overall gold recovery to a gravity concentrate after heat treatment is more than 20 %."

Jan 1, 2018

By Juan Carlos Zevallos

Ante un escenario incierto y de gran tensión como consecuencia de la pandemia del COVID-19, el sector minero peruano ha venido desarrollando tareas sociales fundamentales y comprometiendo grandes esfuerzos en ayuda económica, operativa y logística. Las acciones descritas en este artículo demuestran que en los últimos años las empresas mineras en el Perú han dado un salto importante en la dinámica de su relación con el entorno, la comunidad y el Estado, lo que ha facilitado coordinar aportes y establecer sinergias.

Aug 30, 2020

By James M. Krese

The West Kentucky Division of Island Creek Coal Company, which is a wholly owned subsidiary of Occidental Petroleum Corporation, operates the new Hamilton Mine. It is located six miles West of Morganfield, Kentucky, in the Northwest section of Union County, adjacent to the Ohio River in Lock 50. On July 15, 1968, a unique new coal conveying system was put in operation. This system consists of eight conveyor units carrying coal from the bottom of the mine slope ultimately to barges on the Ohio River. It is over two miles in length and has a total of 3175 connected horsepower. The river loading conveyor is the longest 72" wide conveyor in operation in this country.

Jan 1, 1969

By L. G. Bergh

The experience developing a supervisory control and information systems in a SX pilot plant is presented. The plant is located at the Process Control Laboratory, Santa Maria University, in Chile. In this work, the problem of controlling this process is discussed and related literature is briefly reviewed. Then, an innovative control scheme organized in three levels, local, hydrodynamic, and metallurgical supervisory controls is presented in an architecture including field controllers, PLC, and PC networks. Operating decisions in the metallurgical supervisory control are taken with incomplete information from on-stream analyzers. The control proposed is based on metal and acid concentration predictions of intermediate and exiting streams through the use of dynamic and static models and flow rates and input concentration measurements. Preliminary results are presented. The main objectives are to develop and test intelligent techniques in a hybrid system, and to study measurement and supervisory control problems. It is expected to produce reliable results that will contribute to improve the efficiency of this emerging and important process.

Jan 1, 2007

By J. W. Shield

Refractory sulfide flotation or gravity gold concentrates are coated onto a sized support matrix and placed in a heap configuration for biooxidation. The surface coating is typically less than 0.05 in. thick and the support matrix is preferably composed of 0.375 to 0.75 in. diameter material. The exposed thin coating of sulfides reduces biooxidation rate limitations due to oxygen mass transfer. The large spaces between matrix particles reduce resistance to fluid percolation and aeration in the heap. The capital and operating costs for this biooxidation configuration are significantly less than for concentrate biooxidation in stirred tanks. After 30 to 90 days of biooxidation, sub- sequent gold recoveries exceed those seen in whole ore heap biooxidation and are comparable to recoveries obtained from stirred tank biooxidation processes. Results from laboratory and pilot testing indicate that this technology is a viable alternative for pretreating sulfide refractory gold ores.

Jan 1, 1997

By Laura Steeves, Inoka Eranda Perera, Jhon Silva, Arend Spaeth

"This paper reviews the main concepts ruling the design, implementation and performance of active explosion barrier systems for underground coal mines in the USA. The document examines the parameters needed for the design of this type of system, such as overpressure and flame speed, suppressant deployment speed and duration time of the active barrier. The document also discusses the available solutions for gassy mines and the concepts behind the selection of machined mounted and roadway active explosion barrier systems. The paper includes a review of active explosion barrier systems developed in the USA and South Africa. The paper provides an overview of the current status of this technology in the underground coal mining industry in the USA, and the possible implementation of such systems. The paper concludes with the identification of the future work needed for the successful implementation of the systems in several conditions to enhance the safety of underground coal mine operations and to provide more tools to the miners for their safety.INTRODUCTIONUnderground coal mine explosions can be addressed in two ways, through prevention or mitigation. The United States mining industry practices have emphasized the prevention of explosions in underground coal mines, with little being done to mitigate the explosion once it occurs. Despite successful practices for the prevention of underground coal mine explosions in the US, the threat of an explosion does still exist. Other mining countries around the world have developed and implemented mitigation systems such as active explosion barriers in their underground mines. In the 1970s, the United States Bureau of Mines (USBM) carried out extensive research on the use of active or triggered explosion barrier systems in the US; however, they are not currently used.Explosion barrier systems do not prevent explosions but mitigate the propagation of the shockwave and flame to other areas of the mine. The use of active explosion barrier systems enhance the safety of underground coal mines. Active or triggered explosion barriers will detect the arrival of the shockwave or flame front of the explosion and release inert material to suppress or extinguish the flame. The technology required for active barrier systems is readily available based on their presence in other mining countries and must be adapted for their use in US coal mines. The adaption must consider the coal dust and methane concentrations in US coal mines, the mine geometry, and the mining equipment used."

Jan 1, 2019

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

By Bruce H. Baker

Studies of used or unused refractory materials are excellent examples of applied mineralogy in industry. Refractory materials are mineral substances containing ceramic or chemical bonding systems. Knowledge of the mineral composition, bonding, and textural relationships often explains the resulting physical property values of a refractory and contributes to the interpretation of refractory wear mechanisms occurring in steel plant service.

Jan 1, 1982

By R. W. Harnmack

Hydrogen sulfide generated by the anaerobic respiration of sulfate-reducing bacteria was used to treat pH 2.2 water from the abandoned Rio Tinto copper mine in Nevada. The untreated water contained 550 mg/L Fe, 140 mg/L Al, 90 mg/L Cu, 80 mg/L Mn, 60 mg/L Zn, 4 mg/L Co, and 2 mg/L Ni. The bench-scale treatment system examined consisted of a bioreactor for H2S generation and three precipitator/clarifier units for metal sulfide precipitation and recovery. The treatment system reduced the concentrations of all metals except Mn to less than 0.1 mg/L. Manganese concentrations were reduced by 96 percent to 3.3 mg/L. A CUS/SO concentrate (33 pct Cu) and a ZnS/5° concentrate (28 pct Zn) were produced that may be suitable for metal recovery at existing smelters

Jan 1, 1994

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Nov 1, 2011

By Terry Gerritsen

Electrode control systems regulate power by physically positioning electrodes. Due to the size and weight of the electrodes, this is a slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +I- 20% around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicans's laterite nickel furnace, yielding excellent results with a 3 to I reduction in power fluctuations. Keywords: SPLC, AC Power Supply, Electric Furnace

Jan 1, 2004

By Richter, E. Charikinya

"Mineral processing unit models require information on particulate properties such as particle size, solids flowrate and mineralogical composition to model their operations. Process models that describe the separation process can be classified based on the level of information required from the ore, i.e. the feed stream to the separating unit. The most comprehensive level of mineral processing models is the particle-based modelling approach. Particle based modelling describes a modelling approach where mineral composition, mineral liberation and textural information of particles making up the process streams is used in modelling. The advantage of this approach is that all model streams carry particle level information (size, liberation, shape). This information is obtained by applying automated mineralogy techniques such as Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN) analysis which provide accurate and detailed information on process stream particle properties. Currently the use of liberation information in modelling and simulation is rare, due to the limited number of separation models that liberation data as input. The objective of this study is to develop a particle based model for a dry magnetic separator, where mineralogical information is used directly to simulate a dry magnetic separator operation. Magnetic separation tests were carried out on high, medium and low grade magnetite ores using a laboratory magnetic separator. Streams from the separator were sampled and sized for chemical and liberation analyses. A sized mass and elemental balance around the magnetic separator was carried out. The elemental assays of each stream were converted to mineral quantities and a sized mineral balance was done. QEMSCAN measured liberation data was reconciled to the mineral balance based on mineral quantities obtained from chemical assays. This was followed by the development of a particle based model that calculates the trajectory of a single particle based on its mineral composition and textural properties. The model was tested on experimental data and was able to predict the effect of variation in process feed stream mineralogical attributes (liberation, grade, particle size) on magnetic separation performance. Results of this study highlight the benefits of the particle based modelling approach. INTRODUCTION The extraction of mineral values from ore requires liberation of the value minerals from the gangue followed by their separation. Liberation is achieved by size reduction operations (Desmond, 2008; Fuerstenau and Abouzeid, 2002). Separation of gangue material from value mineral takes place in various mineral upgrading stages such as classification, magnetic separation and flotation. In these concentration stages value minerals are separated from gangue minerals based on the physical properties of the ore particles making up the feed such as size, liberation, volume of magnetic material and density. The success of separation is related to the liberation of the feed particles, the performance of the separation technology applied, as well as the inherent characteristics of the feed material (Leißner et al., 2013)."

Jan 1, 2018

By D. C. R. Espinosa, P. Aliprandini, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel and cobalt are the main value metals in nickel laterite ore. Cyanex 272 is an extractant used to separate nickel from cobalt present in leach solutions. Previous studies demonstrated the extraction of cobalt, magnesium and manganese at pH 5 using Cyanex 272 as extractant, while nickel remained in aqueous solution. However, it is difficult to separate cobalt from a solution containing magnesium and manganese. One possibility to change the metals’ behavior during the solvent extraction process is to change the mixture of extractants used. In order to study the solvent extraction of cobalt from a solution containing manganese, magnesium and nickel, a mixture of two extractants was investigated. Cyanex 272 (CY) and Versatic 10 (VC) were selected as extractants in the organic phase. The extractant concentrations used were: 20% CY; 15% CY, 5% VC; 10% CY, 10% VC; 5% CY, 15% VC; and 20% VC. In all cases, kerosene was used as a diluent, at 80 vol%. The synthetic leach solution used in this study was prepared according to the composition of a typical nickel laterite leach solution. The pH value of the solution used was 5, and the aqueous/organic ratio used in solvent extraction testwork was 1/1. The study has shown that the composition of the organic extractant mixture did not increase cobalt separation.INTRODUCTION Sulfide and laterite deposits are the main sources of nickel. However, production from nickel sulfide ores has been decreasing over the years, relatively speaking, increasing the focus on the exploitation of laterite nickel ores (McDonald & Whittington, 2008). Laterite ore deposits are found in tropical and subtropical regions. A characteristic of laterite ores is the presence of a complex and heterogeneous mixture of metals (Crundwell, Moats, Ramachandran, Robinson, & Davenport, 2011; Georgiou & Papangelakis, 1998; Gupta, 2003; Kesler & Simon, 2015; Moskalyk & Alfantazi, 2002; Oliveira, 1990). Nickel concentrations in laterite ores are typically 1–2% (Dalvi, Bacon, & Osborne, 2004)."

Jan 1, 2017

By Lei Pan, Roe-Hoan Yoon

"Direct force measurement for bubble-particle interaction has been difficult due to bubble deformation, which makes it difficult to know the separation distances between the two macroscopic surfaces. In the present work, we have developed a method of monitoring the deformation accurately, while directly measuring the interaction forces. In effect, we can ‘see’ bubbles interacting with mineral surfaces under different hydrodynamic and chemical conditions and determine both the hydrodynamic and surface forces involved. In the present work, a high-speed camera has been used to record the optical interference fringes of a thin liquid film (TLF) of water formed on a mineral surface. The recorded fringes are then used to reconstruct the spatiotemporal profiles, from which one can determine the hydrodynamic pressure using the Reynolds lubrications theory. From the forces directly measured in the present work and the hydrodynamic pressures obtained from the fringes, we have determined the disjoining pressure. The results show that air bubbles interacting with hydrophilic surfaces form stable TLFs with zero contact angles. The TLF formed on a hydrophobic surface thins fast, form a ‘pimpled’ film, and ruptures to form a finite contact angle. The new information obtained in the present work may be useful to better understand the role of hydrodynamic and surface forces affecting bubble-particle interactions."

Jan 1, 2014

By Z. Smieszek, J. Botor, Z. Miczkowski, S. Sobierajski

"From 1978, the direct process for the smelting of chalcocite concentrates in a flash furnace by the Outokumpu method has been applied at the Glogów II copper smelter. The chemical composition of these concentrates make it necessary to control the process very strictly. In this paper, the method for controlling and measuring the main technological parameters of the copper production by flash smelting is being presented. It includes the determination of the chemical composition of the concentrate, its grain structure, the temperature of liquid products of the process, oxygen content in process gases, as well as lead concentration in copper and copper concentration in slag.The main process parameters are determined from the mass and energy balances. The relations between parameters, such as an effect of grain structure of a concentrate on oxygen and oil consumption, and dependence of chemical composition of a concentrate on capacity and products quality are discussed. 1. IntroductionThe Polish copper concentrates, as most concentrates occurring worldwide, contain from 18% to 30% Cu, and less sulphur (7-11%) and iron (2-5%). The main copper-bearing mineral contained in the concentrates is chalcocite, while bornite and chalcopyrite are present in smaller quantities. Moreover, the organic carbon (5-7.5%), arsenic (0.05-0.3%) and lead (1.2-3.0%) are also contained in the concentrates. The gangue consists mainly of silica, aluminosilicates, calcium carbonate and magnesium carbonate. Their proportions make the addition of slag-forming agents unnecessary.The composition of Polish concentrates, especially their low iron content, allows their application in the direct flash smelting process for blister copper production. Low sulphur content is the factor which determines the necessity of oxygen application in this process."

Jan 1, 1989

By Olanrewaju A. Ojo, Xu Wang, Jian Xin Dong, Lina Zhang, Jerzy A. Szpunar

"The influence of crystallographic orientation on the pitting corrosion behavior of Ni-Fe-Cr alloy 028 was studied by a combination of X-ray diffraction (XRD), electron backscatter diffraction (EBSD), potentiodynamic polarization technique and atomic force microscopy (AFM). The results show that there is anisotropy of pitting corrosion that strongly depends on crystallographic orientation of surface planes. The distribution of pits frequency in standard stereographic triangle shows that the crystallographic planes close to {100} are more prone to pitting corrosion compared to planes of {110} and {111}. The calculation of surface energy (001) and (111) shows that the planes of high packing density of atoms have low surface energy with concomitant strong resistance to pitting corrosion. A correlation function between crystallographic orientation and pitting corrosion susceptibility suggests a method not only to predict the pitting resistance of a known textured materials, but also to improve corrosion resistance by controlling materials texture.INTRODUCTIONNickel-iron-chromium(Ni-Fe-Cr) alloys are widely used in various industries and engineering sectors due to their combination of good mechanical properties and high corrosion resistance(Hibner, 2001; Thomas, 2006; Ghosh, 2005).Ni-Fe-Cr alloy 028 (alloy 028)has such important characteristics worth mentioning. Alloy 028 contains high amounts of nickel, copper and molybdenum which improve its resistant to corrosion attack in reducing medium, and presence of high level of chromium makes it more resistant to oxidizing species. Moreover, alloy 028 is less expensive because of higher amount of iron compared to other similar alloys. Currently, alloy 028 is manufactured as evaporator tubes applied in the phosphoric acid production; production tubing and casing used in deep and sour gas wells; heat exchangers employed in nuclear power plants, and seawater-carrying piping and seawater-cooled heat exchangers (Bankiewicz, 2012; Kivisäkk, 2003; Gómez, 2003; Xian, 2012; Bellezze, 2004)"

Jan 1, 2017

By Katja Reinharter

Arsenic can be found in different sulfidic copper concentrates and residues, which for several years have commonly been used in copper metallurgy, as the “arsenic-free” resources are getting rare. Due to the high toxicity the removal of arsenic in the copper smelting process is a very important topic. The typical chemical slag and sulfur attack on the refractory material is getting enhanced by the presence of arsenic. This work deals with post-mortem investigations of a magnesia-chromite brick and castable used in copper smelting furnaces showing an additional and increased chemical attack by arsenic. The knowledge on the wear behaviour is not only based on a detailed chemical and mineralogical characterization, but also on thermochemical FactSageTM calculations, which are carried out on provided post-mortem samples. Post-mortem investigations on used refractory materials represent an important prerequisite for the product development, as well as for special engineered lining concepts to support our customers.

By A. Saki, P. Gebski, W. Ying

Industrial smelting furnaces are subjected to significant structural changes and deterioration caused by the conditions under which they operate. The current methods for the structural assessment of furnaces include visual inspections, analysis of thermal data, acousto ultrasonic-echo (AU-E) of the refractory lining and surveying of the key structural elements. Acoustic Emission (AE) non-destructive testing (NDT) technique has proven its capabilities for continuous monitoring of industrial installations and structures. Recently, Hatch Ltd. has been successful in applying acoustic emission for monitoring furnace tapblocks, and expanding the scope of the acoustic emission monitoring to the structural integrity of the entire furnace. The capability of detecting emissions related to the fracture development in the furnace shell, movement of the refractory, electrode arcing, combined with efficient source location algorithms makes an acoustic emission system a comprehensive tool for the real-time furnace integrity monitoring. In this paper the concept of such state of the art system for structural integrity assessment is presented. The initial results of the acoustic emission monitoring together with data analysis techniques are discussed.

Jan 1, 2011