Search Documents

By V. Sheikhzadeh, M. R. Sheikhzadeh, A. Haratian, M. Zare

High Pressure Grinding Roll (HPGR) as an efficient grinding technology plays a major role in mineral processing plants. Investigating the effects of this technology on different parts of mineral processing circuits reveals this technology’s capability. In this paper, HPGR grinding effects on an iron ore beneficiation circuit, in comparison with conventional crushing systems were studied. A representative feed sample was taken from an iron ore beneficiation plant, then crushed to minus 6 mm in a laboratory by two methods: HPGR and cone crusher, and finally a concentrate plant circuit was simulated. Plant simulation was performed by doing laboratory tests consisting of grinding, magnetic separation, flotation and filtration on HPGR and cone crusher products, respectively. According to comminution tests results, in particle sizes smaller than 6 mm, a cone crusher product is coarser than an HPGR product. Also, the Bond ball mill work index of the HPGR product was 10% less than the crusher product. Therefore, based on the Bond formula in applying HPGR, ball mill power consumption decreased by 12%. After ball milling to minus 100 microns, magnetic separation tests results showed that the recovery of the cone crusher circuit output was 90.8% and the product Fe grade was 66.4%. For the HPGR circuit these figures were 87.6% and 67.3%, respectively. Therefore, by using an HPGR, a higher Fe grade of the final concentrate was achieved. A flotation test was then performed on the magnetic separation concentrate, where the results showed that the crusher circuit recovery and the sulfur grade of the product were 96.5% and 0.192%, respectively; whereas the HPGR circuit recovery was 97.2% with a sulfur content of 0.185%. Findings revealed that flotation performance in the HPGR circuit was more efficient than the crusher circuit. Vacuum filtration tests on concentrate produced through the HPGR circuit resulted in a moisture content of 12% that was 2% higher than the crusher circuit’s concentrate in the same condition. Keywords: High pressure grinding roll, power consumption, magnetic separation, flotation, filtration

Jan 1, 2020

By M. Mbonami, R. Pretorius, J. Miller, P. Kyony, B. Nel, N. Mautsa

Challenges due to the formation of stable froth in acid leach systems is common at many copper and Ccbalt producers. Stable froth affects downstream process, critical equipment, and operational parameters. In severe cases the froth present safety and environmental risks and increased operational costs. Solids reports in the pregnant leach solution, accumulates, and clogs launders resulting in a potential costly safety and environmental risk. Solvent extraction is operationally affected by crud formation, organic solvent and extractant losses, reduced mass transfer due to the solids carried downstream. This article reviews the generally inadequate mechanical and hydraulic solutions of froth elimination employed over the years. The recent introduction of a chemically based solution able to eliminate froth problems that can potentially turn around the situation for those who adopt the technology.

Jan 1, 2023

By Bruna Brito Freitas

O lingotamento contínuo de tarugos é um processo extremamente complexo dependente de variáveis que influenciam diretamente na qualidade do aço lingotado e na produtividade. Geralmente essa influência é conflituosa. É necessário conhecer melhor os parâmetros de processo para compreender seus efeitos naquilo que é a base do lingotamento contínuo: a transferência de calor na interface metal/molde. Foram levantados dados de temperatura durante o lingotamento de diversas corridas de aços em uma planta de aços longos especiais. As medidas de temperatura das paredes do molde da máquina LC foram obtidas, utilizando-se termopares estrategicamente posicionados ao longo do comprimento do molde e nas suas faces. Através da obtenção dos valores de temperatura desses termopares e do levantamento dos dados de processo de cada corrida monitorada, foi possível correlacionar a influência da velocidade com a transferência de calor na interface metal/molde. Por fim, os resultados mostram que o aumento da velocidade de lingotamento gera um aumento na transferência de calor.

Aug 7, 2018

By Augusto Andrés Torres Toledo

Na mineração a céu aberto, na etapa de planejamento a curto prazo são desenhados constantemente polígonos usados no planejamento de produção, onde geralmente o processo de desenho é manual, demandando o tempo e esforço dos planejadores. Os polígonos gerados no planejamento de curto prazo devem apresentar a menor variabilidade possível entre eles, para que as restrições da planta de processamento sejam atendidas. Desenhar polígonos de curto prazo de forma automática, sequenciar todos os blocos de minério em cada polígono, e conectar um polígono a outro é o foco deste trabalho. Para isso, foi feito uso de algoritmos genéticos e dinâmicos, desenvolvidos em linguagem de programação Python e operacionalizados no software geoestatístico SGeMS. Gerou-se múltiplas iterações para cada um dos avanços individuais de blocos de minério, gerando regiões ou polígonos, e selecionando as regiões de menor variabilidade de teores. As funções de distribuição de probabilade dos teores de cada avanço foram comparadas a função da distribuição de teores global do corpo de minério, os resultados mostram que os polígonos possuem distribuições semelhantes à distribuição de referência, então foi possível sequenciar os blocos de forma operacional garantindo quasi-estacionaridade dos parâmetros.

Oct 30, 2017

By Izabela Diniz Duarte

Perdas térmicas decorrem do armazenamento do aço líquido em panelas. O controle da temperatura do aço líquido é condição essencial para se obter um produto final de alto nível de qualidade. Este trabalho buscou avaliar a transferência de calor a partir do aço para o refratário da panela e para a camada de escória, utilizando um modelo numérico (Computational Fluid Dynamics). As perdas de calor dão origem a correntes de convecção dentro do banho e a consequência típica desse fenômeno é a estratificação térmica. Foi avaliada a influência de parâmetros tais como espessura da camada de escória, tipo de revestimento refratário e a temperatura de encharque. As perdas térmicas para o refratário lateral e do fundo da panela se mostraram maiores que as perdas térmicas para a camada de escória. Nas condições estudadas a espessura de camada de escória não apresenta influência significativa sobre as perdas, ao contrário do tipo de refratário e temperatura de encharque.

Aug 16, 2017

By Olívia Cristina Petriz Monteiro

A Companhia Siderúrgica Nacional (CSN) possui uma Oficina de Manutenção Mecânica Central que fornece serviços de reparo, fabricação e manutenção de conjuntos mecânicos e componentes. A usinagem é um dos setores de maior demanda durante o reparo na Oficina e é considerada o grande gargalo entre as etapas de reparo/fabricação. Na busca por uma melhora na qualidade do atendimento e dos serviços prestados, o trabalho teve como objetivo identificar e implementar um novo sistema de medição para o Controle de Qualidade da Oficina Mecânica, reduzindo a demanda de inspeções dimensionais e geométricas para o setor de Usinagem. Com a compra dos instrumentos de medição tridimensional, o Laser Tracker e o Braço de Medição, foi possível aumentar a disponibilidade da usinagem, diminuir o tempo de inspeção de peças, acelerar o processo de decisão dos reparos, reduzir o tempo de entrega dos equipamentos, aumentar a confiabilidade das inspeções, além de e efetuar eventuais serviços de medição em campo.

Aug 8, 2018

By André Wulff Hirano

O Alto Forno 01 da ThyssenKrupp CSA entrou em operação em 12/07/2010 dando inicio a uma etapa em que o Brasil recebeu sua mais recente usina integrada, sendo um marco no modelo de planta compacta com o nível de capacidade instalada de 5 milhões ton/ano de placas. O modelo de controle de fluxo gasoso centralizado e com baixa marcha periférica havia se mostrado não adequado. Desse modo, foi implementado um monitoramento de indicadores para auxiliar na avaliação e controle de nível térmico e de distribuição de gás. Logrou-se obter uma estabilização da marcha do Alto Forno resultando em um melhor desempenho nas condições de escoamento, melhor rendimento de gás e, por consequência, redução do Fuel Rate, além de uma otimização no custo de carga metálica. Este trabalho mostra o desenvolvimento das práticas operacionais e de controle que permitiram essa evolução nos resultados.

Aug 1, 2018

By John B. Umhau

In 1930 , 65,448 long tons of virgin or primary tin were consumed by 1,292 establishments in the United States , representing about 91 per cent of the total consumption as computed from imports , exports , and stocks at the beginning and the end of the year . The reported consumption was equivalent to 38 per cent of the world's tin production in 1930 , estimated at 171,000 tons , and was 12 per cent less than the 74,369 tons consumed by 1,307 establishments in 1928 . Decreased consumption of new tin in 1930 ás compared to 1928 was a reflection of the general industrial depression . All of the tin- consuming industries showed substantial decreases except tin plate and terneplate , white metal , and tinning , which showed small tonnage increases aggregating only 1,200 tons . The largest tonnage decrease was in the use of new tin in babbitt which declined 33 per cent in 1930 as compared to 1928. This was largely attributable to the decreased production of automobiles and trucks , which was 24 per cent lower in 1930 than in 1928. Percentage decreases in other important tin- consuming industries were as follows : Solder 18 per cent , bronze 19 per cent , tin foil 40 per cent , chemicals 23 per cent , tin oxide 44 per cent , and type metal 46 per cent . The distribution of the amount consumed by various uses during 1927 , 1928 , and 1930 is shown in table 1 . Consumption studies indicate the fact that variation in tin consumption from year to year parallels the fluctuations in demand for the already wellestablished tin products . For example , the manufacture of motor cars and trucks3 required only 11,000 tons of tin in 1930 compared to 19,000 tons in 1928 ; the canning industry continues to require the greater portion of the tin plate and much of the solder . Recently developed industries , while affecting total consumption of bearing metals , solders , etc. , to some extent , have made little change in the relative importance of these commodities as consumers of tin .

Jan 1, 1932

By Oleg Ostrovski

Industrial pyrometallurgical processes in ferrous metallurgy are based on carbothermal reduction of metal oxides. Carbothermal reduction of stable oxides requires high temperatures. Lowtemperature reduction can be implemented by using methane-containing gas with high carbon activity, or by carbothermal reduction under reduced CO partial pressure. Under standard conditions, methane is thermodynamically unstable above 550 °C and decomposes to solid carbon and hydrogen. At appropriate CH4/H2 ratio and temperature, carbon activity in the methane-containing gas phase can be well above unity relative to graphite, which provides favorable thermodynamic conditions for reduction. To maintain these conditions, the rate of reduction/carburisation should be higher than the rate of solid carbon deposition. The paper discusses reduction of pure manganese and chromium oxides at relatively low temperatures, and constraints in reduction of manganese and chromium ores. Reduction of metal oxides by carbon in hydrogen as an alternative use of natural gas is also discussed.

Jan 1, 2014

By S. Eckert, G. Gerbeth, K. Timmel, B. Willers, T. Wondrak, N. Shevchenko, M. Röder

The quality of the produced steel in the continuous casting process is significantly governed by the melt flow in the mold. However, direct flow measurements in liquid metals are still rather scarce. In order to investigate these flow phenomena, three experimental facilities operating with low melting liquid metals were installed at Helmholtz-Zentrum Dresden-Rossendorf (HZDR). The melt flow in the models is measured by the Ultrasonic Doppler Velocimetry (UDV) or the Contactless Inductive Flow Tomography (CIFT), multi-phase flows can be visualized by X-ray imaging. The obtained measurement results are primarily used for validation of numerical models. In this paper we will investigate the fluid flow in the mold and the behavior of the surface of the liquid metal using flow measurements by UDV and surface profile measurement by a laser scanner, respectively. Strong fluctuations and deviations of the free surface were observed in case of a static magnetic field

Jan 1, 2016

By Felipe Daroch, Maria C. Ruiz, Rafael Padilla

Copper concentrates with high arsenic contents must be pretreated before conventional smelting to prevent environmental pollution with arsenic compounds. In this work, experimental results concerning the selective removal of arsenic and antimony from copper concentrates are presented. The process consists of an alkaline digestion using concentrated NaHS-NaOH solutions to transform the arsenic and antimony sulfides into soluble compounds. A water leaching follows the digestion to dissolve the arsenic and antimony, leaving clean copper sulfide solid residues. The laboratory scale tests were carried out using a copper–arsenic concentrate with 15.05% As and 1.42% Sb. The results showed that the most important digestion variables were temperature and concentrations of NaHS and NaOH. Over 97% of arsenic and 92% of antimony could be removed in 10 min of digestion using 8.9 M NaOH and 100% excess of NaHS at 80 °C. The subsequent water leaching was performed at 80°C for 20 min.

Jan 1, 2015

By Zhen Zhang, Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie, Hong-Yi Li

Extracting vanadium from vanadium containing hot metal by LD process has been proven an effective solution for the utilization of vanadium-titanium magnetite ore, but the systematic analyses of vanadium extraction rate and mechanism by basic slag are seldom reported. In this study, mathematical model of vanadium transfer from metal to slag was formulated and the rates of vanadium extraction of hot metal with basic slag were investigated. The results indicated that the apparent vanadium extraction rate constant, kp, were in the range of 1.33~9.07×10-4g/(cm3·s). And the rate constant was increased with the increase of final slag basicity, reaction temperature and stirring gas flow. The apparent of mass transfer parameter decreases significantly from 0.13 cm3/ s to 0 cm3/ s in 20min, and the data changed as negative due to the decrease of slag oxidation and recovery of vanadium from slag to metal.

Jan 1, 2015

By Camila Magalhães Gonçalves

O aço inoxidável ferrítico tipo 430 estabilizado com Nb, com e sem recozimento após laminação a quente, foi laminado a frio e submetido a recozimentos isotérmicos em temperaturas de 650ºC, 700ºC, 750ºC e 800°C por 900 s para análise da evolução da textura de recristalização e do tamanho do grão via técnica de EBSD. Ocorreu o refino do grão após recristalização, resultando em um tamanho final de 12,2 mm. Observou-se um aumento da intensidade das componentes (111)[12 1] e (111)[01 1] da fibra g e diminuição na intensidade da fibra a de deformação. A componente cubo girado, característica do aço laminado a quente, desaparece com a recristalização. As propriedades mecânicas desse aço, principalmente o comportamento em estampagem profunda, são diretamente afetadas por sua textura de recristalização.

Jan 16, 2018

By Márcio Nascimento Cunha

A presença de inclusões não metálicas em aços inoxidáveis é uma das possíveis fontes de defeitos superficiais, especialmente em produtos laminados a frio. Uma das alternativas para evitar as inclusões de óxido de alumínio em aços inoxidáveis é o rígido controle dos níveis de alumínio presentes nas matérias primas adicionadas ao aço. O presente trabalho tem como objetivo apresentar melhorias de qualidade superficial obtidas no aço ferrítico 430 estabilizado ao nióbio (0,20%Nb a 0,40%Nb) produzido pela Aperam através do uso de ferro-nióbio contendo menores teores de alumínio em relação ao produto padrão, desenvolvido especialmente para essa aplicação pela empresa fornecedora do material. Através de resultados industriais constatou-se uma evolução da qualidade com a redução no índice de desvios por esfoliação de 29%, enfatizando não só a importância do controle do teor de alumínio incorporado aos aços inoxidáveis como também um controle rigoroso de processo especialmente em aplicações de alto apelo estético, caso do uso em equipamentos da linha branca.

Jul 30, 2018

By Luis Alberto Sfalsin Passos

A aglomeração de minério de ferro para formação de pelotas é um processo dinâmico e seu controle é complexo. No controle manual o operador local é responsável pelos ajustes no processo e o tempo e a proporção de suas atuações dependem da percepção de cada um. Logo, o controle manual do processo é feito de forma individual e não padronizada e frequentemente não atende satisfatoriamente o controle da taxa de crescimento da pelota crua. Este artigo apresenta uma alternativa de controle automatizada, padronizada e otimizada da taxa de crescimento da pelota crua nos discos de pelotização. O “Sistema de Controle Avançado de Processo”, denominado SCAP, consiste em um controle multivariável baseado em ferramentas de controle convencionais e lógica nebulosa, que simula o pensamento humano nas tomadas decisão. As regras foram construídas e fundamentadas em conhecimentos previamente adquiridos por especialistas do processo. Verificou-se após a implantação um aumento do desempenho do processo produtivo. No âmbito das melhorias, destacam-se: redução de pelotas fora da especificação (granulometria), redução do consumo de insumos (agentes aglomerantes, gás natural, entre outros), melhoria na qualidade do produto final e aumento da produtividade.

Aug 1, 2018

By Chunyang Guan, Jilai Xue, Zengjie Wang, Qiaochu Liu

Molten salts electrolysis method to prepare Al-RE alloys has attracted increasing attention recently. CaCl2 and Na3AlF6 were the most often used melts for this purpose. In this work, Al-Sc alloys prepared by electrolytic deposition process in both CaCl2 and Na3AlF6 melts were investigated, respectively. It was found that Sc distributes almost uniformly and Sc contents increase with increasing current intensity in both melts. Current efficiency was measured for comparison among various current densities applied. The alloy products were analyzed using XRD and SEM, where the formation behaviors of Al-Sc intermetallics were investigated in details. The experimental and theoretical results demonstrate that Al3Sc and Al0.968Sc0.032 are the major precipitates in the Al-Sc alloys prepared by molten electrolysis. The results are useful for selection and optimization of the molten salts compositions and the parameters of electrolysis operation.

Jan 1, 2015

By Baozhong Ma, Yonglu Zhang, Yongqiang Yang, Chengyan Wang, Yongqiang Chen

During the past decades, slurry electrolysis (SE) has been implemented commercially for the processing of bismuthinite and complex Pb-Cu bearing gold concentrates. Recently, SE was proven effective for the treatment of As-rich antimonic gold concentrates. Laboratory test results suggest over 98% of the antimony was extracted, while the extraction of arsenic and gold was less than 0.5%, and that of iron was less than 6%. Moreover, the cathode antimony contained over 98% antimony and less than 0.3% arsenic. Considering the disadvantages of traditional 3 kA slurry electrolysis baths, such as smaller electrode area, reduced capacity, and greater electrode deterioration, the authors have developed an innovative 12 kA slurry electrolysis bath equipped with mesh and fence type titanium alloy electrodes. Furthermore, the technique was successfully used within a pilot scale plant yielding results similar to those observed in the laboratory. The technique yielded ametallic antimony ingot of 99.9% purity after arsenic removal via the addition of Na2CO3.

Jan 1, 2014

By Bingyi Bai, Lifeng Yang, Yanling Guo, Jieyu Zhang, Guoding Gao

In terms of special resources with iron, niobium and rare earth coexisting in Baiyuneboite, the new smelting technology of ferrocolumbite was studied. Reduction experients for the Baiyuneboite and explores ore phase change of Baiyuneboite in the process of reduction was conducted with graphitic carbon as the main reducer and a temperature below 1000 ℃. Moreover, it studies the influence of reducer, roasting temperature and grind fineness on the reduction as well as focuses on the evolution course of iron phase. Through the analysis on in-situ XRD of the raw ore and carbon addition ore, it also develops microstructure change rules of Fe ore phase and ore phase of paragenetic elements for composite ore(Ca, Si, Nb, F) in the process of reduction roasting. In addition, the impacts of temperature on the reduction process are also discussed. With regard to minerals of different particle sizes, the thesis will explore their ore phase changes and microstructures after 10 hours’ reduction under 900 ℃.

Jan 1, 2015

By Shadia J. Ikhmayies

CdSxTe1-x and CdS1-yTey solid solutions are usually formed in the interfacial region in the CdS/CdT thin film solar cells during the deposition of the CdTe layer and/or the processing steps of the device. It is well known that CdCl2 heat treatment encourages the formation of the CdSxTe1-x alloy which improves the solar cell performance. In this work, indium doped CdS1- yTey thin films are produced by first producing CdS:In thin films by the spray pyrolysis (SP) technique on glass substrates, then annealing the films in nitrogen atmosphere in the presence of elemental tellurium. The films are characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and transmittance measurements. The transmittance is used to deduce the optical parameters such as; the extinction coefficient, refractive index, besides to the real and imaginary parts of the dielectric constant. The dispersion parameters such as Eo (single-oscillator energy) and Ed (dispersive energy) of the deposited films are also estimated and discussed.

Jan 1, 2015

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG

Ni-M (Metal=Cu, Fe, Co, Mn, Zn, Cr) aerogel catalysts were tested for CH4 oxy-CO2 reforming. It was found that the Ni-Co bimetallic aerogel catalyst had the highest activity and stability in methane oxy-CO2 reforming among all the Ni-M aerogel catalysts. It exhibited a steady activity of 79 % (in terms of CH4 conversion) at 750 oC, which is the highest activity under a similar reaction condition as compared with those published in literature. Characterizations for the reduced catalysts indicated the formation of Ni-Co alloy, while other transition metals separated from Ni during the reduction process. Therefore, the active species in the Ni-Co bimetallic catalyst showed a stronger interaction than those in other Ni-M catalysts, which might be one of the main reasons for the better catalytic performance of the catalyst.

Jan 1, 2016