Search Documents

By III Feeley

Coal is the nation's most abundant fossil energy resource and serves as the primary fuel for the U.S. electric-power industry. However, its continued and expanded use is often challenged by the nature and amount of its associated impurities, such as mineral matter, sulfur, and trace elements. The moderate- to high-sulfur content of many U.S. coals is of particular concern today as potentially more stringent regulations requiring further reductions in sulfur dioxide emissions are being considered. The most prevalent method currently employed to control SO2 emissions from coal-burning facilities is post-combustion flue-gas desulfurization. However, physical coal cleaning (a.k.a. beneficiation, preparation) methods can also be effective in removing sulfur and ash impurities from coal prior to combustion. In a typical physical cleaning operation, raw coal is crushed to about 50-mm (2-inch) topsize, and then screened into coarse, intermediate, and fine size fractions. Crushing liberates some of the ash-forming minerals, including the portion of inorganic sulfur (pyritic) not chemically bound to the coal matrix. The percentage of impurities liberated generally increases as the coal particle size is reduced. Coarse- and intermediate-sized coal particles are typically subjected to specific gravity-based cleaning methods, while fine-sized (less than 0.5-mm) coal particles are beneficiated using froth flotation, a technique based on surface property differences. Greater cleaning potential exists at finer sizes because of increased liberation of impurities, but this potential is not fully realized because of inefficiencies associated with fine particle separation using state-of-the-art coal cleaning technologies.

Jan 1, 1990

The considerations which led to the decision to_ install discs at the Dampier Pellet Plant of Hamer ley Iron Pty. Ltd. are described. Initial testwork showed that the ore could be ground dry in open circuit to a Blaine index of 2500 cm2/g and that it pelletized readily. The various design criteria including diameter, slope, speed, motor size, depth of sidewall, feed point and water spray location were then determined. Plant performance after commissioning is described including the various problems encountered and the modifications since carried out to overcome them. The main problem was quickly identified as disc feed rate control. Various bin and bin feeder modifications were tried to overcome the effects of the fluidising characteristics of the dry ground ore. Other factors found to affect disc operation are ore size distribution, additives and operator competence.

Jan 1, 1974

By Willard C. Lacy

Survival of the mining industry as a viable economic entity in the United States is being seriously threatened by declining grades of ore reserves, rising operational and capital costs, and increased governmental taxes, restrictions, and subsidizing of third world competition. Discovery of major high-grade deposits is becoming increasingly unlikely. International competitiveness of the U.S. deposits will depend upon 'Yankee Ingenuity', innovations in mining methods, metallurgical treatment, and financial arrangements, and a viable national strategy. This will require not only effective management for control of operations, but management that encourages breakthroughs in technology, financing, labor relations, and in public and governmental understanding. The mine geologist and the exploration geologist both have important roles to play in all aspects of this fight for survival of the industry.

Jan 1, 1984

By J. C. Heter

Industrial Mineral Fillers, LLC. is in the initial stages of mining and processing Anorthosite (CASPAR TM) at its CASPAR mine located in Soledad Canyon, Los Angeles County, California The CASPAR is being mined from the Precambrian San Gabriel Anorthosite Complex of the western San Gabriel Mountains. Preliminary results suggest that CASPAR is a desirable alternative to silica sand used in construction applications, such as, stucco, grout, abrasives, and other uses including filtration and golf course recreation sands. With the use of standard ore dressing techniques, CASPAR is suitable for use as a filler in paint, plastics and rubber. Environmentally, CASPAR has advantages over silica sand, in that, there is no detectable Free Silca.

Jan 1, 1997

By S. J. CRAIGHEAD

IN 1912 the United States Smelting Refining and Mining Company made a large investment in a number of coal properties in Utah and in 1915 a subsidiary, the United States Fuel Co., was organized to take over these properties. Operations started in 1916 and the Company soon became, and remains, one of the major coal producers of the State. It now produces approximately one million tons of coal annually, which is about 22 per cent of Utah's output. The U. S. Fuel Co. owns large reserves of good coal and is in a position to expand operations with the industrial growth now taking place in the West. Traveling through the Western States, one is struck by numerous advertising signs portraying the picture of jovial Old King Cole of nursery rhyme fame. His rotund figure and beaming countenance are the symbols of Utah King Coal, the product of the King mine of U. S. Fuel Co. King Coal is a by-word of quality coal throughout all the Western States.

Jan 1, 1948

By C. L. HUSTON

MY ANCESTRAL connection with the manufacture of boiler plate runs back through four generations, and my personal acquaintance with the practice reaches back to the time, in my ,boy- .hood days, when iron plates' were made in a mill operated entirely by water power. -The mill originally was driven by an old-fashioned "'breast" water wheel 20 ft. in diameter and with a20-ft. face, geared direct to the roll train. When the mill slowed up and there was danger of its stalling, the men would jump upon the rim and help the wheel around with their weight, to prevent a "sticker." Later, as large plates were called for, a flywheel was set out of line so that it could' be speeded up by gears from the water wheel and connected back again,. by reducing- gears, to the roll train. The flywheel, with its cast-iron rim and wooden spokes, made 90 r.p.m. and the roll train 45 r.p.m. In 1870, our company installed our first steam-driven plate mill two-high rolls, 84 in. long. In these early mills the hot metal was manipulated by hand.

Jan 1, 1920

The Putnam Coal Mine, at design capacity, will be the third largest underground bituminous coal mine in the world and will feature the world's longest single flight belt conveyor. Construction is now in process; initial mining will commence in early 1969 and design capacity will be reached in 1971. I'm Jerry Workman, Assistant Mining Manager for the Coal Group of the Mining and Metals Division of Union Carbide Corporation, and I am acting as Project Manager for installation and start-up of the Putnam Mine. The Putnam Coal Mine reserves are located in south-central West Virginia and contain approximately 27,000 acres of prime Pittsburgh No. 8 coal; reserves are sufficient to support a 3.5 MM tons per year operation for over 30 years. The mine portal area is located some six miles inland from the Kanawha River. The river loading facility is located approximately 156 miles by way of river from the market.

Jan 1, 1968

The Australasian Institute of Mining and Metallurgy (AusIMM) is a professional society for all those associated with the activities of the mineral industry. Differences of opinion exist within the membership of the AusIMM on the role it should play in the future as a professional society in a changing industry and world environment. This same dilemma is concerning other professional societies of which the author is a member. Some of the activities and priorities of the AusIMM are reviewed in order to clarify a frequently expressed opinion that it identifies with and supports industry at the expense of representing the interests of its individual members. By definition and by action this is certainly not the case and it is concluded that all activities whether seen to be industry or member orientated serve to benefit both. The AusIMM plays a most important role in integrating and promoting the interests of all sections of the mineral industry whether corporate or individual and the Presidential activities in education this year provide an excellent example of this.

Jan 1, 1997

By Patrick Shea

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management, U.S. Forest Service and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the National Park Service, U.S. Forest Service and Bureau of Land Management. The U.S. Department of the Interior has worked with the U.S. Geological Survey, the U.S. Forest Service, the U.S. Environmental Protection Agency, and western state governments to identify and prioritize these sites on Bureau of Land Management, National Park Service and U.S. Forest Service administered lands. This presentation will discuss the accomplishments we have made to date to clean up inactive and abandoned mine sites, focusing primarily on lands administered by the Bureau of Land Management.

Jan 1, 2000

By David R. Brosnahan

Increased Cu grades due to chalcopyrite-rich ore from The Doe Run Company's new Casteel Mine prompted a program to increase Cu recovery. Preliminary tests indicated that prohibitive quantities of FeS2 float with chalcopyrite. Point counting of mill stream samples showed that locking was not a major problem, although grinding to finer particle size enhanced the floatability of both chalcopyrite and marcasite. Backscattered electron images and microprobe analyses of FeSz minerals revealed the presence of Pb which appears to occur as solid solution in marcasite, and as a sub-micron particulate Pb phase in pyrite.

Jan 1, 1987

By J. Janeson

Wall control at the Pipe Open Pit is of primary importance in ensuring the long-term stability of the operation, while keeping costs to a minimum. Blasting techniques have been adapted to the variations in competence and structure of the wall rocks. A portion of the perimeter wall is being developed in incompetent peridotite . A recent change in pit slope design provides a wide safety berm on alternate benches. A support program which consists of pinning the crests of wide berms with vertical reinforced concrete dowels and horizontal bolting of walls shows evidence of increasing the stability of the pit walls. This paper describes the blasting and support techniques which are contributing to successful wall control in the Pipe operation.

Jan 1, 1979

By Libby R. Ricafort, Nonato S. Retardo, Jose B. Anievas

This paper shows the metallurgical test results that led to the design of the heap leach facilities of Philex Mining Corporation. The design incorporates a water management model as process solution circulation is excessive with high rainfall intensity in the area. This poses problems in the operations requiring stringent controls than would be necessary in a less severe environment. The corporate perspective embraces on environmentally-sound mineral development. A budget is always provided to environmental management making certain that no industrial development is moved forward at the expense of the environment.

Jan 1, 1996

The ores described in this paper are from the two principal orebodies at Wiseman's Creek, a small village about 22 miles south-east of Bathurst in central-western New South Wales.The first official reference to mining at Wiseman's Creek is in "Mineral Statistics of New South Wales" of 1875, which reported that the Wiseman's Creek Copper Mining Company had proved a lode-later known as "North Wiseman's"-to a depth of 120 ft., where it was found to be 20 ft. wide. By 1876 the erection of a mill and smelting works had commenced, and the sulphide ore found to contain copper lead, zinc, silver and gold. Some oxidised ore was also being worked. Operations were, however, generally unsuccessful, and sporadic work up until 1907 produced only about 5,000 tons of ore. The other more important orebody of the locality-the Phoenix-was not opened until about 1895. By 1908, as reported by J. E. Carne, the shaft had been sunk 340 ft., with the extraction of both oxidised and primary ore. At the time of the slump in copper, pric'es in 1907 approximately 3,000 tons of, ore had been produced.Several smaller orebodies were discovered and worked during the same period as the North Wiseman's and Phoenix, but their output was more or less insignficant. THE OREBODIES AND THEIR GEOLOGICAL SETTINGIt is now impossible to examine the orebodies underground, but they appear to have formed a series of flat lenses, whose major axes were parallel to ,the foliation of the enclosing quartz-chlorite-muscovite schists. The largest ,of these lenses was worked as the North Wiseman's orebody, which was reported by Carne to vary in width from 1 ft. to 20 ft., and which probably extended discontinuously over a strike length of about 1,000 ft. The Phoenix orebody is stated to have varied from 1 ft. 6 in. to 3 ft. in width...

Jan 1, 1955

By Toussaint LF

A brief history of the mineral sands industry is given from a radiation protection standpoint, with gamma radiation and inhalation of radioactive dust being identified as the main sources of radiation exposure of persons working in the plants. The principal sources of gamma radiation exposure are identified and the history of early bagging methods is discussed. The concept of ALARA is introduced and the impact of the "bulka bags" (and more effective monazite storage facilities) are detailed as illustrative examples of dose minimization, together with the requirements for the transport of monazite. The dose from radiation received from inhaled dust is dependent on a number of parameters of the dust, some of which are not well known. ICRP 30 (1978) makes recommendations relating to the intake of radionuclides by workers. These recommendations are discussed with respect to the inhalation of dust containing thorium. The possible pathways of radioactive material throughout the body are also described. The effect of having parameters that differ from ICRP 30 is discussed and suggestions are made relating to measurements that can be carried out to more accurately determine these parameters. Since in some instances the exposures to dust yield personal doses which may exceed the annual ICRP 30 based limits, it is necessary to define more accurately parameters of the dust so as to determine more accurately personal Doses.

Jan 1, 1986

By Knapp. Arthur

THE ORDINARY well log is subjected to a great deal of criticism, much of which is well founded. Sometimes, though, the difficulty in interpreting the log is due to the fact that the geologist or engineer using the logs does not know the limitations of the drilling method used. The rotary drill, especially, has inherent limitations that make it difficult, to secure .definite information at all times. The identification of well-defined key beds is about all that can be expected from the rotary log. The formation in a drilled hole, as reported by the driller; has a direct relation to the speed with which the drill makes the hole or to the reaction of the various strata on the bit, called the "feel of the bit." When this is not thoroughly understood by the geologist or engineer endeavoring to interpret the log, the result is an erroneous correlation with other wells or a discarding of the log as worthless. GENERAL TERMS Hard and Soft.-Hard and soft are relative terms. In the case of well logs, they are very misleading as they are used in connection with both resistance to abrasion and resistance to percussion. In technical rock classification, hardness is relative resistance to abrasion. The term brittleness is used in connection with resistance to blows. These terms are misleading to the geologist or engineer who is not familiar with both the cable-tool, or standard tool, method of drilling and the rotary method. In the case of the standard tools, the driller's report of the hardness of the formation is in terms of its resistance to blows. For instance, a cable-tool driller might be able to make from 30 to 50 ft. a tour in a brittle limestone, which he would call soft and at the same time he might call a relatively soft (from a purely mineralogical standpoint) gypsum hard, because it is somewhat elastic and is not readily broken by blows. The rotary driller would reverse the terms. The limestone is hard in that it resists the abrasive action of the bit, while the gypsum might be soft in that it is readily cut by the rotary bit. It is rare that wells drilled by the

Jan 2, 1920

By Thomas B. Douglas

INSTRUMENTATION in the process industries can no longer be regarded as a convenience, but rather an absolute necessity. Although many chemical processes must already be conducted with instruments, every properly designed application of automatic process control will improve operation: 1) the product will be more uniform and of higher quality; 2) the manual labor saved will reduce cost; 3) uniformity of flow and uniform control of process will increase production; and 4) surges will be eliminated, making it possible to operate equipment near ultimate capacity at all times. Industrial instruments fall into two general classifications-those that measure and those that measure and control. The cement industry has been using instruments for a number of years, particularly in the burning process, primarily for indicating and recording. Automatic process control makes additional use of these instruments, and others, to control variables. Assisted by the instrument manufacturers, engineers at Ideal Cement CO. achieved considerable progress in determining how well the usual recording instruments could be made to control various phases of cement-making. The results of these experiments were used to make the new plant at Houston as wholly automatic as possible.

Jan 2, 1958

By Manuel Gutierrez, Roberto Gomez, Juan Aravena, Johan Gjoevad

The use of explosives in mining operations is a process that involves the search for an ideal explosive for the type of geological condition of the mineral to be extracted. For the explosives present on the market the majority are based on Ammonium Nitrate. This as it is an ideal balance of high energy efficiency achieved with low development of gas emission. The manufacturing and loading operation of the explosive requires multiple process stages and different raw materials, which, if is not correctly supervised and controlled may cause the development of harmful gases or, in the worst case, even toxic gases. The majority of mining operations are located at remote locations without the presence of communities, and hence individuals, which could be affected by emission of the harmful or even toxic gases. In these operations the protection is mainly to protect the employees of the operation. However, if the operation is located near communities, the effect of these gases becomes a serious problem. The communities' perception of post-blasting gases, according to interviews carried out in this project, describes these as smells of black gunpowder, damp soil with a volatile permanence and medium intensity, sometimes a stinking tone is added. The legislation in Chile that controls the exposure of “workers” to different gases is Supreme Decree 594, 2019 (Decreto Supremo 594). Currently the Chilean Ministry of Environment and Sernageomin (Servicio Nacional de Geología y Minería) are taking actions to reform and strengthen oversight, seeking through a short law to provide more tools to the government to decentralize decisions in case of non-compliance with the decree. This paper describes the development and implementation of a permanent and remote gas monitoring system, considering the reasons for choosing the gases to be included in the equipment, the types of sensors and their capabilities, the way to verify in the field the correct functioning of the technology throughout the project, and finally how the data collected in the field is meeting the government's expectations in terms of permanent and online reportability. Additionally, it addresses the continuity of gas monitoring in the community that will disappear in the short term due to the expansion of mining operations, thereby ensuring the protection of both workers and affected communities.

Jan 21, 2025

By Altair Lúcio de Souza

A laminação de tiras a quente com laminadores Steckel tem como característica um perfil de temperatura mais baixa nas pontas sendo este um dos motivos que geram cargas de laminação muito mais altas nesta região. A carga de laminação elevada tem como consequência no processo a geração de desvios de planicidade e o alto risco de rompimento do material nos passes finais de laminação. Este trabalho tem como objetivo demonstrar os benefícios da utilização da estratégia de Tapering para a laminação de tiras de espessura fina em laminador Steckel. Foi feita a comparação das cargas de laminação do material laminado e o acompanhamento dos resultados de planicidade obtidos antes e depois da implantação desta função. Ao fim do trabalho verificamos que a estratégia de Tapering é essencial para o processamento de materiais finos com laminadores Steckel.

Jul 30, 2018

By Wojciech Szczepiński, Dominik Gächter

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Oct 1, 2021

By H Kusumi, A Nishio, K D. Halim, Y Yun

In Japan, evaluation of rock mass is crucial in mountain tunnels that are constructed using the NATM (New Austrian Tunneling Method) to determine the support pattern that in turns determine the final support structure of the tunnel. The current evaluation method is highly dependent on the observations of on-site expert engineers that grades the rock mass in four levels across nine criteria: A. Condition of tunnel face. B. Condition of excavated surface. C. Compressive rock strength. D. Weathering. E. Spacing of discontinuity. F. Condition of discontinuity. G. Orientation of discontinuity. H. Spring water. I. Water degradation. However, in recent years, the number of said experts are decreasing rapidly due to labour shortage caused mainly by an aging population and declining birth rates. This is one of the biggest challenges that the construction sector currently faces, and this may affect the efficiency of tunnel construction projects in the future. Thus, this study proposes the implementation of a deep learning tool called the convolutional neural network (CNN) to quantitatively evaluate rock fractures on tunnel face. In addition, Gradient-weighted Class Activation Mapping (Grad-CAM) is applied to visualise CNN, as well as verify the applicability of CNN to the evaluation of rock fractures. In other words, by creating heat maps of tunnel face images, CNN is utilised to evaluate rock mass in categories that are associated with discontinuities. The CNN model is most accurate when six convolution layers, four pooling layers, and three dense layers are used. This yields an accuracy of 75.0~88.0 per cent. Thus, the CNN model is verified to be feasible method to evaluate rock fractures.

Nov 29, 2022