Search Documents

By R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13. per cent, of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 258, Special 178 and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings.

Jan 1, 1927

By R. V. Subramanian

This project financed by the Bureau of Mines investigated the use of polymers to achieve rock bonding and reinforce coal mine structures for better or permanent ground support. Support was achieved by pumping the polymers into the rock interstices to bond the mass together for increased structural competence. Holes were drilled in the mine roof, after which the polymers were injected at about 100 psi to permeate the cracks. Initial laboratory work indicated that of all the resin systems tested, the epoxy resins could most likely be modified to be suitable for rock injection. This was confirmed when several potentially suitable resin systems underwent intensive evaluation. In a series of three field tests, two conducted in a copper mine with coal mine-type shale and the third in a coal mine, it was shown that the polymers penetrated cracks less than 0.005 inch wide. The fast-setting epoxy systems, cured out in thin films under mine conditions, produced a bond exceeding the strength of the uncracked virgin rock.

Jan 1, 1974

By R. M. Ray

The Bureau of Mines evaluated five commercial badge-type carbon monoxide dosimeters. Color changes in the badge reagent indicated the presence of carbon, monoxide. Possible effects of ambient conditions on dosimeter response to CO during or after coal mine fires or explosions were studied. Temperature and humidity changes did not change dosimeter sensitivity to CO. Contaminant gases such as CO2, N02, S02, and H2S had effects that varied with brands of dosimeters ranging from no effect to increased sensitivity to CO. Dosimeters tested after 6 months of storage showed an increase in failure rate as high as 25 percent. Tests were conducted to determine the effects on dosimeter time-for-color change caused by observer's sight (colorblind); lighting, and coal dust on dosimeters. No significant effects were observed. Observer variance was the most pronounced factor observed in all tests.

Jan 1, 1975

By V. Casaletto, L. Widdifield

"Equipment capable of higher production requires more sophisticated maintenance programs. Reduction in fleet size through use of modern technology requires higher utilization and greater availability.Caterpillar's maintenance control system program will display the capabilities of computer technology in a maintenance environment. Utilizing such resources will provide increased availability, lower inventory requirements, fewer last minute disasters, and lower cost per ton for maintenance. High production from premium quality equipment can only be realized by good planning and care, executed by maintenance and operating personnel acting cooperatively.IntroductionAccurate information is the key to accurate decision making. In today' s competitive industry, mines' teeter on the brink between profit and loss. Their survival will be predicated on their ability to retrieve, analyze, and formulate accurate information regarding the operating costs of mobile equipment. This paper deals with the impact of managing equipment operating costs and introduces a computerized control system designed for monitoring and controlling these costs.Caterpillar has produced several computerized modelling programs designed at taking the guesswork out of equipment selection and management. The most basic of these is Equipment Investment Analysis (E.LA.). This model compares two or more alternatives over the projected life of the machine. It deals with comparisons in the owning and operating costs of equipment, as well as, their productivity over a specified period of time.In order for a computer model to be credible as a decision making tool, it must be simple to use and the results measurable and accountable . Caterpillar has introduced several computer models to assist the industry in selecting and managing an equipment fleet. These programs allow the user to predict and monitor the operating costs and production capability of mobile equipment. They are often used in the machine selection process to select equipment which best suits a mine's long-term cost per tonne objectives. After the optimum selection is made, Caterpillar's Maintenance Control System provides an efficient management tool to monitor and verify the data used in the selection model."

Jan 1, 1992

By N. D. Fernandes

Labour-intensive narrow reef stoping, as traditionally practised in South African gold and platinum mines, is almost unique in the modern first-world mechanized mining environment. Shortcomings of the system include the ever increasing cost of labour, a cap on achievable productivity and a poor safety record, particularly in the field of rock-related accidents. In the absence of sustainable alternative technologies, the South African mining industry has spent millions of rands improving the present system, focusing on improving workplace safety. This paper details the changes to stope support at Impala Platinum?s Rustenburg operations, and the impact on rock-related safety performance. Keywords Stope panel support, narrow reef stoping, improving workplace safety.

Jan 1, 2011

By Robert L. Llewellyn

Preparation of coal begins at the face in underground mines or in the pit with surface mines. Impurities in raw coal can be in the seam itself or in extraneous material taken in mining from the roof or bottom. Raw coal is prepared only to the extent that is necessary to make the product salable. Over 60% of all coal production is processed to some extent in cleaning plants. For underground mines the proportion cleaned is 72% as compared to 42% from surface and 15% from auger mines. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only as necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent and only incidently with mines shipping raw run-of-mine coal crushed to a top size of, usually, 2 to 4 in., with little, if any, other treatment. ECONOMICS OF COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-rang planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and atomic energy. Cod prices for power plants are still on a Btu (British thermal unit) basis but with more emphasis on sulfur content. For metallurgical coal, the lower and medium volatile coals are in demand and the price rises, generally, as the volatile percentage is lower. Moisture affects the Btu value of coal almost the same as ash content, but dusty conditions during loading and unloading are no longer accept-

Jan 1, 1973

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement .Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By Stephen Hall

Introduction Marine Autonomous Systems are making rapid progress from their early years as research tools for university departments & government institutes into having a growing number of real-world applications for industry, academia, statutory inspection, data acquisition and defence. Deep sea mining offers a distinct set of challenges that are very well suited to autonomous underwater vehicles (AUVs) and to a lesser extent for autonomous surface vehicles. Deeper, smarter, more capable Global demand for rare earth metals and high-grade ore will inevitably lead to exploitation of deep ocean resources as terrestrial reserves become depleted or remain unavailable for political or environmental reasons. Winning production licenses from the international seabed authority and especially gaining public trust to undertake deep sea mining activities and licenses will depend upon high quality pre-exploitation scientific surveys of the sea floor ecosystem, and subsequent monitoring of the impact of mining activity and remediation work. The actual area covered by the seabed mining operation may be quite small in terms of square kilometres, but still larger than can be patrolled by tethered ‘eyeball’ class Remote Operated Vehicles, so multi-spectral inspection, assessment and monitoring will be more effective when carried out by untethered AUVs. By using seabed recharging stations and data upload points the AUV can stay in situ in the deep ocean, rather than be repeatedly brought back to the surface.

Jan 1, 2018

The Wednesday morning session started with a film "The Greatest Good" presented by the Colorado Mining Association, courtesy of A. George Setter. President Joe Taylor opened the business meeting at 9:30 a.m. He called for a report from the Auditing Committee. The report was read and a motion was made for approval. It was made, seconded and approved. The report from the Resolutions Committee was submitted by Mr. Robert Delaney, Chairman of the committee. It reads as follows: RESOLVED: Whereas, in the year since the last convention of the Rocky Mountain Coal Mining Institute, the Institute and the coal mining industry generally have suffered the loss through death of the services of:

Jan 1, 1968

By P H. Ferreira

The mechanisation of mine development is becoming increasingly important in our South African and Southern African mines with increased emphasis on safe and efficient mining. Raise, blind and shaft boring offer mechanised solutions for excavations such as:- [reef raises stope boxholes and shaft ore passes ventilation passes and shafts chairlifts large vertical hoisting shafts (in excess of 1200 metres in depth) angled hoisting shafts (from small to large diameter bored holes)] These techniques will be discussed with reference to relevant applications and the author?s comparison between conventional drill and blast techniques.

Jan 1, 2005

By B. Chalmers, L. Bäckerud

The growth temperature of dendrite tips has been measured in a binary alloy system, Al-Cu, as a function of rate of formation of solid phase. Metallographic examination has rerealed the dendritic structure dereloped during different stages of the freezing process and factors influencing the undercooling, such as solute buildup, surface tension, and kinetic effects, have been estimated. Practical implications of the results are discussed. THE development of a dendritic growth pattern during the solidification of metals and alloys has an influence at least equal to that of grain size on the properties of the casting or ingot being produced. and consequently much interest has been devoted to the study of this phenomenon. A review of the knowledge gathered up to 1964 has been given by Chalmers.' Among recent publications in the area the works of Jackson et al 2 and Flemings and his coworkers3,4 are of special interest. This work is an experimental study of the factors which influence the development of a dendritic pattern during the solidification of a typical binary alloy system, A1-Cu, when there is no heat source in the liquid. This means that the temperature and the temperature gradient are controlled by the heat extraction from and latent heat evolved by the growing crystals. EXPERIMENTAL PROCEDURE Samples were prepared from a master alloy made up of aluminum, 99.995 pct, and copper. 99.99 pct, of the concentrations given below and of sufficient size to fill cylindrical graphite molds of 35 mm ID and 35 mm height. Bottom. wall. and lid of the graphite molds were all of 6 mm thickness, Fig. 1. Thin ceramic thermocouple shields could be introduced at different positions in the sample through holes in the lid. The assembly was heated in a small vertical resistance furnace to a suitable temperature. 700° to 720°C. which is well above the melting point of the sample. It was thereafter taken out of the furnace and chilled at selected rates, and the temperature changes in the sample were recorded. For high sensitivity in the temperature recordings, a reference thermocouple was held in a solidifying pure aluminum melt. which was very well insulated and therefore was at a constant temperature. 660°C, for nearly half an hour. The thermocouples were connected so that the difference voltage was fed into the recorder of which the most sensitive range was 1 mV. Temperature variations could be read to within 0.l°C. The thermocouples used were of the Chromel-Alumel type (28- or 38-gage wires) and the recorder a two-pen Moseley strip chart recorder. The different rates of chilling were obtained in the following way. a) The graphite crucible was wrapped in one or two layers of an insulating. feltlike material (Fiberfrax paper from the Carborundum Co.). The drop in temperature per unit time after complete solidification could thereby be varied from 8" to 18°C per min. This corresponds to a rate of heat extraction in the given samples from 0.08 to 0.17 cal cm-' sec-I. 6) The bare graphite mold was placed free on a piece of firebrick. The measured temperature drop was around 50°C per min (-0.5 cal cm-" ' sec- I). c) By blowing compressed air through a tube with many holes surrounding the mold in a ring shape. the rate of heat transfer could be raised to 150' to 200°C per min (-1.7 cal cm-3 sec- I). d) Cooling rates around 1000 C per mill (-9.4 cal cm-3 sec-l) were obtained by substituting the air in the device used in c by water. The range of cooling rates used in these experiments correspond to technical casting processes from slow solidification as obtained in sand molds to very rapid freezing which occurs in some continuous casting and welding processes. EXPERIMENTAL RESULTS The A1-Cu system was chosen for the experiments: the relevant part of the phase diagram is reproduced in Fig. 2. Observation of the Center Temperature. When a thermocouple is inserted in the center of the melt. the type of cooling curves obtained at slow solidification rates differs little from numerous published curves from similar systems. and the solidification pattern

Jan 1, 1970

By Marc C. Betournay, John E. Udd

"In this study, the authors investigated the stabilities of slopes cut predominantly into Trenton limestone in a large quarry in the Montreal region. Analyses of the bench and pit walls indicated that small-scale toppling, ravelling, and wedge failures are the most likely modes of instabilities. Because most of the joints dip steeply, however, the conclusion was made that relatively high walls could probably be justified.The field investigations were supplemented with the determinations of the shearing strengths of artificial discontinuities that were cut into samples of the limestone. The properties of a fine-grained limestone were found to be influenced very much by the magnitudes of the loads that were applied, while the properties of a crystalline limestone were found to be much less, or not load-dependent.The study is one of a number that are being conducted in this area.IntroductionExtensive quarrying has been done in the sedimentary strata of the Montreal area for a very long time. By any standards, it can be said that the Island of Montreal is a major mining area. At present, approximately 20 quarries are being operated in, or near, the city of Montreal.In addition to the millions of tons of limestone that are removed each year, a large number of excavations for foundations are cut into the sedimentary rocks.To date, however, very little information has been published concerning the engineering properties of the local geological materials. No mention is made of this aspect in the references which are presently available.Because of this lack of information, the senior author has initiated a study in which the strength properties of most of the rock types, and of the natural discontinuities contained in these, would be investigated. To date, the results of one other investigation have been published and other work is in process. It is hoped that the end result will be a comprehensive knowledge of the important strength properties of all of the rocks in the entire region."

Jan 1, 1983

By G. F. Comstock

In the literature of metallography there is a large amount of material describing the various non-metallic inclusions found in iron and steel, and the appearance of sulfides, silicates, oxides, or alumina in steel under the microscope is fairly well known. The inclusions found in non-ferrous metals are, however, not so well known, at least judging from published writings, and the author has been interested in examining small castings of copper, brass, or bronze with certain inclusions purposely mixed with the metal, to see what was the characteristic appearance of each kind of inclusion, and if they could be readily distinguished from one another. The method employed in most cases consisted in overheating and oxidizing a small charge of copper, then cooling it somewhat, and adding a suitable amount of the element whose oxide it was desired to observe. This element was stirred in well and given time to react with the oxygen in the copper, then the melt was poured in a sand mold in the form of a cylinder about 21/2 in. (63 mm.) in each dimension, with a sprue about 11/2 in. (38 mm.) in diameter and 3 in. (76 mm.) high on top of the cylinder, the sprue forming the only riser. Samples for examination were cut sometimes from the center of the casting, and sometimes from the sprue or riser. A few of these samples were cast in chill molds. The appearance of sulfides was studied in an alloy containing 10 per cent, each of tin and lead, with which a flux of plaster of Paris was used. The appearance of foundry sand was studied in several alloys, one of them having sand stirred into the metal intentionally, and others having cut into the molds badly when poured, so that the castings were spoiled by included sand. As all this work was done on alloys having copper as the chief ingredient, the natural starting point was copper oxide, the appearance of which in a micro-section is well known. Cuprous oxide is soluble in molten copper, but separates out in freezing and forms a eutectic containing 3.5 per cent. Cu20, or 0.39 per cent. oxygen. If there is less

Jan 1, 1919

By W. C. Goldberg

This paper presents pit slope monitoring and back-analysis case studies con-ducted to evaluate and, if possible, stabilize slopes at the Berkeley Pit in Butte, MT. Two specific slopes were studied in detail. The first slope was determined to be near limiting equilibrium, as evidenced by its response to the initiation and cessation of mining, while the second failed on three occasions. Back-analysis of the failed slope verified the laboratory-derived geomechanical properties of the earth materials. Early detection of slope movement can show a need to take action, including modifying slope geometry, dewatering if the slope were wet, and/or investigating and implementing artificial supports. Monitoring slope displacements in open-pit mines can supply data for predicting collapses and preventing serious damage, injuries, and/or loss of life.

Jan 1, 1989

By R. E. Molnar, P. A. Riveros, V. M. McNamara

"This paper describes some recent research done at CANMET in the areas of ion exchange and A VR (Acidification- Volatilization Reneutralization), as applied to the recovery of gold and cyanide, respectively. It also discusses the ways in which these two technologies may be combined in order to minimize the environmental impact of gold milling operations and optimize reagent usage. IntroductionGold milling operations can essentially be divided into those that carry out a liquid/solid separation after leaching and those that recover gold directly from a leach pulp. The former produce a barren solution which may contain considerable amounts of cyanide, either free or cornplexed with metals. The latter produce a similar solution but this is now part of a slurry rather than a clear stream. Due to its toxicity, any excess cyanide must be destroyed before the effluent is discharged into the environment. Ideally, this should be (and sometimes is) accomplished by natural degradation. However, in many cases natural degradation alone cannot remove the last traces of rnetallocyanide compounds from the effluent and , as a result, most Canadian gold producers utilize a supplementary chemical oxidation system. This not only increases the operating costs, but concerns have also arisen in recent years about the formation of ammonia as a result of the chemical oxidation of cyanide (via CN--CNO--HCNO-NH3) ·"

Jan 1, 1993

By J Harmse

This paper deals with the modernisation of the brakes on an electrically coupled Blair multi-rope hoist and covers the removal of the old calliper brakes and hydraulic control system, and its replacement with brake discs, disc braking units and hydraulic control systems. The paper covers the braking requirements of the hoist, which is made up of two electrically coupled single-drum hoists, together with the theory behind the choice of brakes and control systems supplied. The paper also covers the project logistics that were required in order to install and commission the new brakes and control systems with the minimum disruption to production on the only rock hoist on a major production shaft. Items covered include the modifications to civil works, pre-installation of bearing lubrication systems, brake discs and hydraulics and the interfacing of the new hydraulic control system to the existing electric control system. It had to be designed to be compatible to a new electric drive and control system due for installation at the end of 2005.

Jan 1, 2005

By Yingchang Tsenshan Wang

UUIN L&SS 1» Paqb I. Introduction........................................................658 1. Subject and Scope...............................................658 2. Acknowledgments...............................................659 3. Review of Previous Work........................................659 Field Data...................................................659 Experiment.a1 Data............................................662 4. Plan of Present Investigation.....................................662 Method of General Procedure...................................663 I1. Experimental Work..................................................663 A. The Solution of Sphalerite..............................:........663 1. The Solvent Effect of Iron Sulphates upon Sphalerite...........663 2. The Solubility of Sphalerite in Salt Solutions of Silver, Copper and Lead...............................................668 B. Formation of Zinc Carbonates....................................674 3. The Reactions of Carbonates and Bicarbonates With Solutions of Zinc Salts............................................674 4. The Reaction of Zinc.Sulphate Solution With Limestones.......684 C. Peculiar Conditions Affectitig the Formation of Zinc Silicate (calamine) and Zinc Carbonate (smithsonite)..........................686 5a. The Effect of Carbon Dioxide Upon the Basic Silicate and the Carbonates of Zinc in Water, and Its Bearing Upon the Conditions of Theii Precipitation..............................686 5b. The Reactions of Solutions of Soluble Silicate With calamine and Smithsonite in Solution in Presence of Carbon Dioxide..689 6. The Reactions of a Mixture of Hydroxide and Silicate of Sodium with a Dilute Solution of Zinc Sulphate...................691 D. High-Temperature Methods.....................................692 7a. The Influence of Temperature on the Formation of Calamine..692 7b. Possible Effect of Heat on Calamine and Srnithsonite.........697 E. Summary of the Experimental Work..............................698 III. Petrographic Work....................................................700 1. The Occurrence of Sphalerite in Limestones or in Cherts............701 Summary of the Blende in Limestones and in Cherts.............7432 2. The Partially Altered Sphalerite and the Oxidation Products........702 a. Smithsonite with Blende....................................702 b. Calamine with Blende......................................703 c. Smithsonite and Calamine..................................703 d. Summary on the Partially Altered Sphalerite and Its Oxidation Products..............................................704 IV. Concl~~siom ........................................................-705 V. Microphotographs and Photographs with Their Explanations.............705

Jan 1, 1916

By Gary Hawthorn

"Laboratory testing, by Lakefield Research determined that, in spite of the relatively high pyrite content of the Golden Rose (GR) orebody, it would respond well to gravity concentration followed by either direct cyanidation or cyanidation of a flotation concentrate.Economics favoured the former choice which became the adopted process flowsheet.During the latter stage of the feasibility study, the Dekalb 500 tpd copper flotation mill became available in the Highland Valley of British Columbia. This plant was purchased by Emerald Lake Resources, and was moved to the Golden Rose minesite.The crushing and grinding circuit were retained and the original flotation circuit was replaced with a 400 mtd gravity plus cyanidation circuit. The plant commissioning commenced in August 1987, and by early September was processing 300 tpd.HistoryThe Golden Rose Mine was operated by Cominco during the period 1935 to 1941 processing 146000 tons grading DAD oz/t Au at a rate of 110 tpd .The process flowsheet consisted of gravity plus amalgamation followed by cyanidation.Metallurgical TestingThe underground mining areas were below the level of Emerald Lake, and had flooded on abandonment in 1942.Samples for metallurgical testing were collected from exposed faces underground once the mine had been dewateredin 1984.In spite of the anticipated high pyrite content of the ore samples, it was apparent from the success of the previous operation that the pyrite did not interfere with the gold recovery.Laboratory testing, at Lakefield, determined that, from a technical perspective, two metallurgical options existed, as shown in Tables I and 2.Note that the very high pyrite content of the ore precluded the possible direct marketing of concentrate. The process flowsheet, therefore, had to contain a cyanidation circuit for the operation to succeed financially.Although the anticipated metallurgy was excellent with either option, the 2.1 % increase in gold recovery with the gravity plus cyanidation option made this the clear choice."

Jan 1, 1989

By C. Scala, M. Gondouin

Published laboratory data have established that very significant streaming potentials can exist across mud cakes subjected to pressure differentials such as exist between a mud column and formation fluids. Since shale is similar in kind and in properties to a well-formed mud cake, it appeared possible that streaming potentials might also arise across shales. A practical consequence would be that the streaming potential contribution to the SP would be smaller than might otherwise be assumed since the SP is measured with respect to the "shale bare line". The resultant contribution would be the difference between the streaming potential across the shale and that across the mud cake. In order to investigate this possibility, a laboratory apparatus was devised for measuring streaming potentials under pressure conditions normally encountered in wells. Reported data on streaming potentids across mud cakes were verified. More important, appreciable streaming potentials were found across shale samples. As in the case of mud cakes, the shale potentials varied with the concentration and nature of the impregnating electrolyte. Dependence on pressure was In a different rela-tion than that for mud cakes, possibly because of the lower compressibility of shales. The differences in streaming potentials between the shales md mud cakes were generally small, although they might vary considerably in practice depending on the relative electro-kinetic properties of the particular shale-mud cuke combination. A "poorly eflective" shale with a "very eflec-tive mud cake" would produce the largest negative addition to the electrochemical component of the SP. Results of field experiments with pressurized wells were considered in the light of the laboratory results. INTRODUCTION Field experiments wherein the pressure of the mud column in a borehole was varied have often indicated the presence of a streaming potential, but its magnitude was not easily predictable and its sign sometimes changed from one formation to another in the same well.' In the interpretation of SP logs from standard surveys, nevertheless, the correct value of R,, is very frequently obtained, within the limits of field accuracy, using only the simple electrochemical expression of the SP provided that proper corrections are made for bed thickness, ion activity, etc.' Accordingly, it was apparent that the streaming potential component of the SP in a borehole was considerably more complex than commonly assumed and clarification was indeed necessary The close similarity in nature and constitution of a shale to a well-compacted mud cake suggested that a streaming potential might also exist across shales as pointed out by M. P. Tixier in 1953 and as recently emphasized by Wyllie." e practical consequence would be that the streaming potential across the mud cake would be canceled, at least in part, on electrical logs since the SP is recorded with respect to the shale potential as a base line. This appeared to be a plausible explanation for many of the effects observed but no supporting data were available. In 1955 preliminary experiments at low pressures were conducted in our laboratories which supported the hypothesis of the shale streaming potential and formed the basis for later studies at borehole pressures.* EARLY LOW PRESSURE EXPERIMENTS The early experiments were conducted primarily to determine the possibility of a streaming potential across shales. The shale used was a compact type designated as No. 7 from Reagan County, Tex. (Permian). Cut samples were saturated for over one month in .2 to 2.0-N NaCl solutions. In order to eliminate all electrode polarization effects, a dynamic method was used. A transient pressure of about 1 atm was applied across

By Fred C., Bond

DETERMINATIONS of circulating load in a classifier operating in closed circuit with a grinding mill are usually made from screen analyses of the mill feed and classifier products. The percentage remaining on someone selected screen size must be used in the calculation, and, because of the wide variation in average particle size between the mill feed and classifier overflow, an accurate and representative result at the selected mesh is often difficult to obtain. To overcome this difficulty and reduce the time required in making the determination, I have devised a method which uses the liquid-solid relationship in the circuit rather than screen analyses. The quantities required for the calculation include only the usual dilution and feed tonnage measurements, which should be made regularly in the course of ordinary mill operation and, in addition, the amount of new water added to the classifier, or to the head of the mill with the new feed. If measurements are obtained on both of these quantities it is possible to check the calculated circulating load, and to calculate the percentage of moisture in the new feed to the mill; or, if the latter is known, to check the feed tonnage.

Jan 1, 1937