Search Documents

Studying the ore textures in a discrete orebody is a novel approach to estimating liberation potential of the ore minerals present. As part of a PhD thesis, this project aims at classifying and quantifying the textures of the Hilton North orebodies, and at estimating their liberation characteristics.

Jan 1, 1993

Jan 1, 2005

By David C. Oyler, Paul B. Stubbs

The Bureau of Mines and United States Steel Corp. are conducting a joint project to monitor formation pressures at a large (23-well) coal- bed gas drainage field near Oak Grove, AL. Three monitor holes were drilled in late 1981, and pressure monitoring began in December 1981. The Bureau of Mines direct method was used to obtain gas content data from cores taken in the monitor holes. Comparison of the 1981 gas con- tent data from the monitor holes with initial gas content values obtain- ed from the production wells in 1977 indicates a 50-pct reduction in ad- sorbed gas content inside the pattern and a 29-pct reduction at one point 500 ft outside the pattern. The combination of pressure and gas content data has also allowed an in situ isotherm curve, relating the formation pressure to adsorbed gas content, to be developed for the area of the production wells. From the current rate of pressure decline (1 lbf/inz per month), the observed changes in gas content, and the isotherm curve, it appears that most of the early gas production came from within the pattern, but since 1981 (and possibly earlier) most of the gas produced has been migrating to the wells from outside the pattern area.

Jan 1, 1985

By W. D. Kruger

Methods for analyzing flooding or cycling projects by means of two-dimensional flow calculations are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The accuracy of such analyses depends on the basic reservoir data employed, especially the absolute permeability distribution in the reservoir; however, absolute permeability data normally are determined from well flow tests and/or core measurements and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. A calculation procedure is presented for determining the areal permeability distribution in the reservoir. Use of the procedure allows verification of the basic reservoir data through the matching of past reservoir conditions, thereby providing proper data for reliable predictions of future operations. The calculation procedure is a numerical technique based on a mathematical model of the reservoir and is designed for solution by means of an electronic digital computer. Results from field application of this procedure are presented. Permeability distributions from measured data are compared to those calculated to indicate the need for the analysis. Comparisons of field-measured and calculated pressure distributions are given to establish the validity of the calculation procedure. The conclusions of this paper are (I) use of the calculation provides data that allow a match of past reservoir conditions and thus reliable prediction of future operations; and (2) the procedure should, where applicable, be used to provide adequate reservoir data for use in two-dimensional flow calculations and related reservoir analyses. INTRODUCTION One means of providing more precise engineering control over reservoir operations during all stages of depletion is to develop some type of model to simulate the reservoir, using information developed from the behavior of the prototype to predict the performance of the actual reservoir. The use of mathematical rather than physical models for this purpose has been gaining in importance recently because of the application and availability of electronic computers. Mathematical models avoid instrumentation difficulties and allow easier handling of large-scale problems. At present, analyses employing two-dimensional models are common, and thought is being given to the use of models in three dimensions. The use of multi-dimensional models is necessary to show not only what is occurring in the reservoir, but also where in the reservoir the phenomena of interest are taking place. Methods for analyzing flooding or cycling projects by means of two-dimensional numerical models are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The applicability of numerical models and the results of using such analyses have been presented through field examples. The references indicated here discuss fully the data necessary to build the mathematical reservoir model and the way the model is used to study or predict the future performance of the reservoir. The accuracy of the analysis of such projects depends on the basic reservoir data employed in the construction of. the model. In order to be sure the model represents the reservoir, it must be used to match some known set of reservoir conditions, i.e., to match past reservoir performance. The accuracy of the model is directly dependent upon the absolute permeability distribution in the reservoir; however, absolute permeability data are normally determined from well flow tests and/or core measurements, and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. There is always the need for better data and for verification of existing data. The purpose of this paper is to show the use of the mathematical model to match past performance in flooding or cycling projects, the use of numerical techniques to adjust the basic absolute permeability data if necessary so that a match is obtained, and in this way to generate the effective areal permeability distribution of the reservoir. A review of the basic concepts of the numerical model will be given, followed by a discussion of the data-adjusting technique for matching past performance. TWO field examples will be cited to show

By P. G. Winchell, J. K. Jackson

The strtcture of body-centered Fe-Ni-C alloys (0 to 16.5 wt pct Ni) containing less than 0.015 wt pct C was investigated by measuring the carbon-diffusion peak at low frequencies with a torsion pendulurrr. By determining the Snoek damping in ferrite and in quenched alloys of identical composition, the effects of nickel content and heat treatment were separated, and the existence of a structure in which Snoek damping is greatly reduced was revealed in the quenched ternary alloys. The relative amount of this structure increases with increased nickel content and cooling rate. It is proposed that this structure may be highly imperfect or tetragonal. In Fe-Ni-C alloys containing only ferrite the addition of nickel (0 to 5.1 wt pet) decreases tke area of the carbon-diffusion peak and shifts its position to lower temperatures but broadens the peak only slightljl. The decrease in peak area with increasing nickel implies that short-range interactions with the nickel atoms prevent some of the carbon atoms from participating in the relaxation process. The shift in the peak position indicates a long-range effect of nickel on the movement of carbon atoms so that at 300°K the diffisivity of carbon in -ferrite is increased by about 35 pct by the addition of 5.1 tut pct Ni. The results are presented as distributions of relaxation strength 072 the activation energy under the assumption that the frequency factor is invariant. BODY-CENTERED iron-base solid solutions dissolve carbon interstitially in the octahedral sites. The occupation of an octahedral site produces a tetragonal distortion of the surrounding lattice. These sites fall into three sets according to the orientation of the tegragonal distortion associated with each and may be identified by their lattice coordinates as: type 1/2 0 0, type 0 1/2 0, type 0 0 1/2. At low carbon levels in cubic ferrite the carbon atoms are distributed at random1 among these sites. In high-carbon body-centered iron-base solid solutions, which are unstable with respect to several two-phase mixtures, a tetragonal structure occurs as the product of the diffusionless transformation of austenite. This transformation is commonly accompanied by appreciable microstrain and its product is called martensite. The tetragonality of martensite, a supersaturated solution of carbon in a iron, is maintained prior to decomposition even though local diffusion of carbon occurs as evidenced by carbide precipitation. The tetragonality is taken as evidence that one set of octahedral sites is preferentially occupied by carbon. (This preferential occupation is called ordering below.) Support for this view is presented by the absence of strain-induced carbon-atom diffusion in high-carbon solid solutions (martensite). Such diffusion occurs in ferrite and produces the 40°C internal-friction peak observed at 1 cps frequencies.' Thus, there appears to be qualitative evidence favoring the view that at sufficiently high carbon levels tetragonality arises spontaneously as a result of the ordering of the carbon atoms; however, no experimental evidence exists concerning an equilibrium between cubic and tetragonal body-centered solid solutions. Moreover, attempts to estimate the energy of ordering7-' predict a value too low to maintain the tetragonality observed at medium carbon levels, 0.3 to 0.6 wt pct C. In the present work an attempt using internal-friction measurements is made to establish the presence or absence of tetragonality in low-carbon body-centered solid solutions formed by quenching austenite. Fe-Ni alloys containing about 0.01 wt pct and 0 to 15 wt pct Ni were selected for the study. While the work was in progress Gilbert and Owen10 reported that the transformation which occurs in these alloys during quenching at rates up to 5000°C per sec is not martensitic but is more properly categorized as massive. Thus, the solid solution

Jan 1, 1964

The Lihir deposit in Papua New Guinea (PNG) contains an estimated mineable reserve of 454t (14.6M oz) of gold in refractory sulphide ore. The Lihir Joint Venture has submitted a proposal to the PNG Government to develop an open pit mine and to install a process plant and associated infrastructure facilities on Lihir Island. The proposed process plant will employ whole-ore pressure oxidation technology, has a design capacity of 2.825Mt/a of ore containing 7.20 sulphide sulphur, and is expected to average 19.3t/a (620,000 oz/a) in gold production during its first 12 years of operation.An extensive program of process development testwork and feasibility engineering was completed to establish the process plant design for the Lihir Project. Summary results of this test-work as well as key design criteria, the process flowsheet, and major equipment selected for the commercial plant are presented and discussed.

Jan 1, 1994

By I. N. Zavarine

AUSTENITE is often defined as a solid solution of carbon or carbide in a nonmagnetic form of iron. Conversely, magnetic measurements are often used by investigators for the purpose of detecting the degree of austenite decomposition after an iron alloy has been subjected to certain thermal or mechanical treatments. Association of the magnetic state with the gamma-phase decomposition is often extended to the alloys of iron with elements other than carbon. Definition of austenite as a nonmagnetic solid solution cannot be accepted in the light of available information without certain reservations. The relation of magnetic transformations with the gamma-phase decomposition in the complex alloys of iron has never been rigorously proved. The present investigation deals primarily with the magnetic trans-formation that occurs in carbon steels during the quenching process. The work was further limited to a study of magnetic transformation in carbon steels quenched at such rates as are necessary to retain the product of austenite decomposition in a martensitic state.

Jan 1, 1934

By W. R. Reed

Drilling with water has the potential to significantly reduce the respirable dust concentrations generated from small-diameter rotary drills when drilling blastholes on surface mining operations. However, water adverseky affects tri- cone drill bits commonly used in surface drilling operations, causing excessive wear and premature replacement. Consequently, dry drilling with a dust collector system has the most widespread use in the industry. Tests have been conducted by the National Institute of Occupational Safety and Health (NOSH), Pittsburgh Research Laboratory (PRL) on a newly designed device for smaller diameter drills that separates the water from the bailing air before it reaches the bit and thus provides the cost benefit of dry drilling while providing the benefit of wet drilling for dust suppression. The water that is delivered to the hole with the bailing air is separated from the air by a proprietary mechanical device that is encased in a drill sub (short section of drill rod/pipe) located immediately behind the cutting bit. A cascade cyclone and a real-time dust monitor were used to sample dust emissions from the holes. Dust concentrations and silica content were measured when drilling dry versus drilling wet. The tests show that drilling with this water separating sub can reduce both measured dust emissions from the boreholes and visible dust around the drill rig.

By Ancel St. John

During a session on coal and coke at the February, 1926, meeting of the American Institute of Mining and Metallurgical Engineers, the writer called attention to the important work on the X-ray analysis of coal1,2 being carried on in England by C. Norman Kemp and his associates. This aroused so much interest that a paper on the subject was requested for the October meeting. It has seemed advisable to make this paper a preliminary survey of the present status in the application of X-ray methods to coal problems and to follow it from time to time with further articles as the art develops. A survey of this sort naturally divides itself into two parts, radio-scopic analysis of the distribution of constituents through the body of the coal, and diffraction analysis of the state of association of the elementary components. In this article the subject matter concerning radioscopic analysis has been drawn almost entirely from the writings of Kemp and his associates and the illustrations have been sptcially furnished by him. It is a pleasure to record here a great indebtedness for this courtesy and cooperation. The subject matter and illustrations concerning diffraction analysis are taken from the author's unpublished researches. Nature and Properties of X-rays Before proceeding it is well to recall the nature and some of the properties of X-rays, as well as our present conception of atomic structure According to the accepted theory atoms are composed of electrically-charged particles. A positively-charged center, called the nucleus,

Jan 1, 1927

By Donald D. Smythe

Tars paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point 90 km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of São Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a by-product of kaolin mining. These deposits, and, a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé. The first is 190 km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriaé area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto

Jan 1, 1946

By Robert L. Akre

When Marco Polo visited China in the 13th century, no one knew what black powder was except the Chinese; they knew enough to make dazzling fireworks with it. But the realization that black powder could also do useful work came much later and, like all important discoveries, it altered the course of history. It was in the 14th century that black powder was first used to break rock in a very crude way; there were no drills and the powder was simply poured into cracks and exploded by setting it afire. Because its energy value was pretty low, the need for something more powerful was felt when the industrial revolution began. In the 1850s, miners began experimenting with liquid nitroglycerine on a limited scale. This was a very sensitive and dangerous explosive. Fortunately in the 1860s, Alfred Nobel succeeded in stabilizing nitroglycerine by absorbing it in kieselguhr-and a new product, dynamite, was born. With it, miners were able to unleash the great energy of nitroglycerine for blasting purposes. But dynamite was still a very sensitive explosive. In subsequent years, other explosives of various strengths and characteristics were developed, such as blasting gelatin, gelatin dynamite, ammonia dynamites, (all containing some nitroglycerine or nitrostarch), and liquid oxygen explosives. These products and their variations supplied the blasting trade for many years. A grained ammonium nitrate product containing some carbonaceous material entered the market in the 1930s. This explosive had below-zero sensitivity-meaning: a No. 6 blasting cap imbedded in it would not detonate it. A more sensitive initiator, called a primer, was needed to detonate this mixture. From Rags to Primacord to Solid-State The first initiator for an explosive charge was probably a rag slowly burning its way to the charge; this method was quite unreliable. Then came the burning fuse, which was an improvement. Next was the nonelectric blasting cap initiated by a fuse. With these initiators, a miner needed quick reflexes and good legs; upon lighting the fuse, he had to run immediately for cover. Development of the electric blasting cap that allowed for accurate timing eliminated this hazard; the electric cap, however, introduced other safety problems because of its susceptibility to extraneous electricity, e.g., ground currents, lightning, and static electricity. These caps also became available in millisecond delays. Development in the mid-1930s of Primacord, a detonating fuse insensitive to electrical currents or impact, further reduced blasting hazards, and is generally acknowledged as the safest known means of initiation. Eventually, Primacord millisecond connectors also became available for delay patterns in blasting. In the mid-1960s, the Primadet delay was introduced; it is a practical nonelectric detonator system that offers the precise timing of electric blasting caps-and is immune to the hazards or effects of extraneous electricity. Recently, Research Energy of Ohio, Inc. introduced a new type of solid-state blasting machine that combines a sequential timer and delay caps. It enables the efficient breakage of rock with a minimum amount of shock, ground vibration, and noise. Improvements in Blast-Hole Drilling World War II created an enormous demand for coal and other minerals in the U.S. and elsewhere. Great efforts and large amounts of capital were spent to find new mineral deposits and develop better mining methods. But while mechanization in mining proceeded at a rapid pace particularly in open-cut work, there was a definite lag in developing new or improved machines for drilling blast holes. The industry continued to depend largely on horizontal, churn, and pneumatic drills. No better machine was available for large scale production. The need for improvement in this phase of mining became more acute in the post-war years. Despite efforts toward further mechanization, mining costs rose rapidly because of mounting inflation and increasingly high wages. In most operations, drilling and blasting the overburden became the principal item of cost. Therefore, whatever size holes were being drilled, the holes had to be spaced so that any foot of the bore hole could be loaded with the maximum load required for the number of cubic yards of material that each foot of the hole was carrying. With the smaller holes that were being drilled, the proportion of drilling cost to the total drilling and shooting cost was much higher than it would have been with larger holes (because of the closer spacing required by smal-

Jan 1, 1977

By Richard D. Hagni

Abstract-Although the ore microscopist routinely examines polished sections to determine the mineralogy and texture of ores, his importance to the solution of problems peripheral to geology is not always fully realized. The techniques which he uses can be applied with little modification to the solution of a wide variety of beneficiation problem. By extending his studies beyond those normally considered to be of interest to the geologist, he can include examinations of polished sections of selected mill products. This is a logical extension, because the minerals and textures in the polished sections of ores are the same as those in mill Products. The mill dressing engineer should be more aware of the types of beneficiation problems that can be solved by the ore microscopist and what the ore microscopist can do for him. A greater degree of cooperation between the ore microscopist and the mill dressing engineer can be of significant mutual benefit. Ore microscopy holds an advantage over chemical analysis, because the interrelations and combinations of the mineral constituents of an ore or mil1 product can be visually determined. This advantage provides solutions to many beneficiation problems. Locking is a type of beneficiation problem that is particularly amenable to ore microscopy. The percentage, type, and distribution of locked particles can be readily determined with the aid of an ore microscope and an estimate made of the extent of additional grinding required for liberation. The extent of intimately locked types, which no reasonable amount of grinding will liberate, can also be evaluated. Mineral coating conditions, free particles of a deleterious mineral, and free particles of a valuable mineral held in floculated clusters of gangue are other features that can readily be observed. In some instances, visual examination may show that the problem is not one of locking. Photomicrographs illustrate the variety of beneficiation problems for which the ore microscope is applicable. These problems and their resolution demonstrate the importance of the instrument and show the value of close coordination between the mill dressing engineer and the ore microscopist.

Jan 10, 1978

By Arthur Notman

SacRamento Hill is a mass of granite porphyry intruded along a fault between Paleozoic sediments and pre-Cambrian schists in the Bisbee district, Cochise County, Arizona. The intrusion invaded both walls of the fault to a large extent, and the accompanying extensive mineralization of the Paleozoic limestones is the locus of the great high-grade copper orebodies of the Bisbee mines. Prior to 1909, although the presence of ore in the masa of the hill itself had long been suspected, systematic exploration had not been attempted. A few shallow pits on the surface here and there had disclosed some chal-cocite with associated carbonates as stringers in a mass of strongly brccciated, silicified, and iron-stained porphyry. The workings in the surrounding limestones had penetrated the porphyry in a dozen or SO places for some distance from the contact but had disclosed no ore. However, the rock had been largely altered to quartz and sericite and very thoroughly impregnated with pyrite and traces of the copper sulphides. A close geological study of the conditions, both surface and underground, strengthened these suspicions, and plans for prospecting the hill were made in 1909. Reference to the accompanying illustrations, Figs. 1 and 2, will give an idea of the general appearance of the surface. The mineralization is more intense in two main zones, one at the west end and the other at the east end of the hill. The outcrop of the hill is elliptical and approximately 3,000 ft. long by 1,400 ft. wide. The Sacramento shaft, which is the main hoisting shaft of the mine and situated at the east end of the hill, as shown by the accompanying map (Fig. 3), offered a convenient base for prospecting that end of the hill, while the workings from the Holbrook shaft offered a similar opportunity at the west end. The choice of level for the first work was determined by analogy with the most favorable depth for enrichment below surface obscrved in the other disseminated deposits of the Southwest.

Jan 1, 1916

By A. S. Keh, H. A. Wriedt

The Precipitation of nitrides in quenched Fe-N alloys, aged between 25° and 200°C, was studied by transmission electron microscopy. Different dislocation substructures were introduced into the materials by recrystallization, cold working, and by Phase transformation prior to the introduction of nitrogen. It was found that the precipitated nitrides, tentatively identified as Fe16N2, have (100) habit planes. Nucleation takes place Preferentially at dislocations and at subboundaries. It sometimes occurs in the matrix, probably on vacancy clusters, but rarely on high-angle boundaries. The process of nucleation on dislocations and subboundaries is very temperature dependent. At room temperature there is no particular orientation relationship between the dislocations involved and the (100) planes on which the nitride Particles formed. With increasing temperature, the nucleation sites tend to become restricted to those dislocation segments lying in (100) planes. The change of yield stress of the 0.022 and 0.043 pet N alloys during quench aging can be correlated semiquantitatively with the change in particle distribution. Strain aging in quenched alloys can be separated into two stages. The early stage is attributed to nitrogen segregation to dislocations and the later stage is associated with precipitation. When previously quench-aged specimens were strained and aged, no additional Precipitates could be seen, although a considerable amount of strain aging occurred. DURING the past two decades, the precipitation of nitrides from a iron has been extensively studied by various techniques. It has been established that two types of nitride exist. The stable nitride, Fe4N, forms at temperatures above 250oC and Fe16N2, the

Jan 1, 1962

By Charles S. Barrett

Metallurgists are making use of the stereographic projection to a steadily increasing extent. In the last five years no less than 20 papers in American metallurgical journals alone have employed the stereographic projection; recent books on physical metallurgy, plastic deformation, X-rays and their applications, and crystal structure use it. Mineralogists have used the stereographic projection for many years in the description of symmetry classes and crystal planes, for it presents an accurate, easily understood plot of any angular relations in crystals with all unessential features eliminated (such as the accidentally determined size and shape of crystal faces). In metallography and physical metallurgy the projection is much used for the analysis of markings appearing on polished grains: slip lines, twins, cracks, structures formed by precipitation, magnetic-powder patterns, etch pits, etc. Data from certain types of X-ray photograms are most conveniently analyzed by its use, particularly those for determining the orientation of single crystals or the preferred orientation of grains in an aggregate. Calculations of how to tilt or cut a crystal parallel to a certain crystallographic plane or to reflect X-rays from a certain plane are rapidly carried out. It has been adopted almost universally to the exclusion of other methods by those studying the deformation of metallic crystals, save where the accuracy required is greater than a few tenths of a degree. Any directional property in a crystal or polycrystalline material can be shown on a stereographic projection; for example, the modulus of elasticity, yield point, etc. It has been repeatedly called to our attention that there is need of an elementary explanation of the principles and methods of stereographic projection, covering all the common applications in the field of metallography and physical metallurgy. The following contribution is an attempt to fill this need. The description of each method is supplemented with references to publications in which the method has been used. For convenience to the reader, these illustrative references are chiefly in American journals, particularly the publications of the American Institute of Mining and

Jan 1, 1937

By Chester A. Rowland

INTRODUCTION Comminution is generally a feed preparation step for subsequent processing stages; exceptions being when a final product such as aggregates, specification sand, Portland Cement, and similar products is produced. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding -- primary and secondary), natural or manufactured non-metallic media (pebble milling) or manufactured metallic media -- steel rods, steel or iron balls. This chapter will discuss general mill design and the specific design and application of the following types of tumbling grinding mills. [Overflow Rod Mills Figure 1 Peripheral Discharge Rod Mills Figures 2 and 3 Compartment Mills Rod and Ball Figure 6 Ball Figure 6a Pebble Mill Figure 6b Overflow Ball Mills Figure 8 Diaphragm (Grate Discharge) Ball Mills Figure 9] I. GENERAL MILL DESIGN A. Liners The interior surface of grinding mills exposed to grinding media and/or the material being ground are protected from wear and corrosion by rubber, metallic, a combination of rubber and metallic, or non-metallic wear resistant materials. B. Drives Economics at the time of plant design and mill purchase determine the drive to be used. The simplest drive is the low speed synchronous motor with speeds in the range of 150 to 250 RPM connected to the mill pinion-shaft by either an air clutch or flexible coupling.

Jan 1, 1982

By O. Morfín

The most probable source of Pb contamination in the perennial reach of Aravaipa Creek, Arizona, has been determined using Pb isotope ratios and total metals analyses of samples collected from the ephemeral and perennial reaches and mine wastes located in the Aravaipa Mining District . Previously, elevated levels of Pb, Cd and As in fish in the perennial reach of Aravaipa Creek, a protected wilderness area,, were assumed to be due to off-site transport from abandoned flotation tailings piles located at Klondyke, Arizona upstream of the wilderness area.Our work replaces this inference with isotopic data that allows us to confirm this hypothesis. The Pb/Zn deposits of the district were mined between the late 1890s and the late1960s, with the most significant ore production coming from one deposit in a rhyolite dike swarm on the Western front of the Santa Teresa Mountains, a granitic pluton of Cretaceous-Tertiary age (~65 ma). Mineralogy has been well constrained across the length of the lode system: Pb and Zn sulfides predominate in the NW sector, and a mixed suite of hypogene/supergene Pb sulfide and Pb oxide minerals comprises the majority of its SE corner. Total metals analyses and comparison of metals ratios serve to constrain the source and transport of certain metals within different parts of the system. Pb isotope ratios in samples, obtained by ICP-MS analysis, define two distinct contributors. The first end-member (208Pb/204Pb = 38.513 to 38.721 and 207Pb/204Pb= 15.550 to 15.598) is characteristic of the mixed, oxide/sulfide ores at the SE end of the deposit. A second end-member (208Pb/204Pb = 38.855 to 38.946 and 207Pb/204Pb = 15.610 to 15.625) characterizes samples taken from the NW, purely Pb sulfide end of the lode. Pb isotope ratios from perennial reach sediments are closely correlated with ratios given by samples from the Klondyke tailings site and by Pb sulfide samples from the NW sector, the primary source of ores processed at Klondyke.

Jan 1, 2003

A sample of fifty fractured low chromium-molybdenum alloy drill steel rods was investigated. Each rod was of the forged collar integral tungsten carbide type in common use in Australia.Examination of a new rod of the same type showed that a zone of spheroidized carbide about 0·25 in. wide was present about 12 in. from the shank end.Examination of the fractured rods revealed that 78 per cent. of failures occurred within 0·25 in. of the spheroidized zone at the shank end but in the main stem of the rod rather than actually in this softened zone where it might be expected to occur.This predominant type of failure at the shank end in the steel rods is caused by a highly anodic region corresponding to the first stages of spheroidization of carbides present in the steel. Accelerated corrosion in the narrow band havil\g this structure induces the formation of stress-concentrating corrosion pits, 78 per cent. of failures in this region being due to corrosion fatigue.The remaining 22 per cent. of failures, occurring in the as-rolled stem, were due to either corrosion fatiglie if failure were initiated at the water-hole surface of the drill rod, or to a decarburized outer surface if failure originated at this surface.Temperatures producing spheroidization were determined as 6007600C.Evidence suggests that approximately 75 per cent, of shank-end failures in all forged collar drill rods can be attributed to corrosion fatigue occurring preferentially in that section showing partial spheroidization of carbides· produced by the forging and hardeningoperations.Methods are suggested for reducing the frequency of fatigue failures in drill rods.INTRODUCTIONAn integral part of all tunnelling operations through rock is the drilling of suitably placed holes i:n.to which explosive is subsequently rammed and exploded.The drilling operation, whether for metalliferous mining or for general civil engineering constructional work; is...

Jan 1, 1955

By Ross Seedsman

Discussion on the design of roof support in tailgates has often been conducted without a clear statement of the stress and failure conditions acting. There is general agreement that in the tailgate the vertical stresses above the chain pillar increase. Within the stress 'bulb' associated with this vertical stress increase there will be an increase in horizontal stress. This does not mean that the horizontal stresses acting across the roof line increase. In retreat longwalling, the proximity of the tailgate to the adjacent goof results in a substantial reduction in the horizontal stress field acting in the immediate roof. Furthermore, at the face/tailgate corner the onset of significant compression of the chain pillar. if it is designed to yield, will result in a further reduction in the horizontal stresses in the immediate roof. It is suggested that this latter mechanism can cause the horizontal stresses in the immediate roof to go to zero. Whatever, the horizontal stress acting across the roof in the face/tailgate corner will be significantly lower than in the face/maingate corner. The implication of the model is that support design in tailgates should be based on the assumption of zero horizontal (in fact tensile) stresses. How the roof behaves in a tensile stress environment is a function of joint spacing and orientation compared to excavation width and direction. It is speculated that the empirical relationship between support density and roof rating results from the relationship between joint spacing and bedding spacing. The onset of stress reductions has major implications to the design of cable and bolt anchorages in the tailgate environment.

Jan 1, 2001

By W. C. Knopf, I. M. LeBaron

In the Carlsbad area potash is dry-mined and wet-concentrated. Wet concentration involves recircu-lation of saturated brines, with resultant difficulties of brine disposal and inherent losses in recovery through solution of the KCl. A dry beneficiation process for potash minerals would offer many advantages over present methods. International Minerals & Chemical Corp. has been working on development of a dry process for some time. This article is a progress report. Potash ores available in this country are largely mixtures of halite and sylvite contaminated with slimes and often with many sulfate and magnesium minerals. Electrostatic concentration of KCl when the contaminating minerals are in low percentage has been accomplished. Continuous production of better than 60 pct K2O concentrate from high potassium sulfate ores has not been demonstrated at the present time. Laboratory Procedure: Laboratory work on electrostatic beneficiation of potash minerals has been carried out using both pure crystals and mined ore. Electrostatic separation of the two main components of potash ore, sylvite (KCl) and halite (NaCl), is accomplished by first heat-treating the ore to allow for electric charging of the particles. Preferential exchange of' electrical charges between different mineral particles through surface contact is the principal mechanism involved. After proper conditioning of the particle surfaces, the oppositely charged minerals are dropped vertically into a horizontal electric field having a field gradient from about 5000 to 15,000 v per in. The particles are free-falling in the field. A suitable power supply is used to produce the proper total voltage for the electric field. Total required voltage is, of course, a function of electrode spacing. A typical electrode arrangement with power supply is shown in Fig. 1. In general, the total voltage on any system is 75,000 to 90,000 v. Power consumption is negligible, as leakage at insulators and corona discharge are the main losses in the system. Optimum preheat temperatures for pure material components generally are not the same as for mined minerals. Fig. 2 shows clearly that maximum recovery on a 50 pct pure KCl, 50 pct pure NaCl mixture occurs at a preheat temperature of about 600°F. In this test the preheat mixture was allowed to cool to about 225°F before dropping through the electric field. The optimum temperature for sep- aration is practically never the optimum temperature of preheat. Optimum separation for mined Carlsbad potash ores occurs when a preheat temperature closer to 900°F is used, as shown by Fig. 3, which plots percent sylvite (KCl) in the concentrate and tails as a function of preheat temperatures. Here again the ore was allowed to cool to about 225°F before separation. It should be noted that efficiency of separation increases continuously with increasing preheat temperatures until incipient fusion of the ore takes place at about 950°F. The increase in optimum preheat temperature for Carlsbad ores over the pure minerals can be traced to the effect of the clay slimes intimately associated with the mined potash. If the slimes associated with the ore are removed by washing with alcohol or other non-aqueous material, the necessity of preheating to the high temperature is removed. This temperature range has been proved critical within these limits during continuous pilot plant operation. Concentrate and tailings grade and optimum recovery also are functions of the temperature of the potash mineral particles during separation in the electric field. Fig. 4 presents data indicating that feed to the rougher pass should range between 150°F and 275°F for best results. It has been found by subsequent pilot plant work that these temperatures can be maintained in actual operation.

Jan 1, 1959