Search Documents

To THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS. GENTLEMEN Like every other significant activity in the United States today, the work of the Institute has been affected by and adjusted to the prosecution of war against Germany, .Japan and their satellites. As the elaborate engines and materiel of modern mobile warfare are made, for the most part, of metals and other minerals; and are powered by mineral fuels, the industries -represented by the A.I.M.E. are of primary and vital importance. Of some 29 critical materials officially listed by the War Production Board, 24 are minerals. An alternate for one of the others, rated as a nonmineral, is to be made principally from petroleum. This alludes, of course, to rubber. The procurement of tremendous quantities of such raw materials and the effective processing, fabrication, and utilization of them depend on members of those branches of the engineering profession represented by the A.I.M.E.

Jan 1, 1943

By Hanes J

More than 200 bursts in coal occurred at Leichhardt Colliery prior to December 1978 during mine development in the 6 m thick Gemini seam at depths approximating 400 m. Three large bursts each displaced more than 300 tonnes of coal and stone. Two of these which occurred in continuous miner developments, are described and compared. Geological settings, mining strains including induced cleavage and roof failures associated with bursts are described. A shotfiring technique replaced mechanised mining following a major incident at the colliery. Present mining procedures, the apparent improvement in stability of workings and ongoing geotechnical monitoring programme are discussed.

Jan 1, 1980

The Split Rock low grade copper prospect was discovered in 1969 by Cyprus Mines Corporation using stream geochemistry. Cyprus "Imes carried out geochemical and geophysical investigations, geological mapping, and percussion and diamond drilling, and concluded that the grade of mineralisation was too low (0.1% copper) to be of interest. In the present study, the geology was remapped and very substantial differences from the previous observations are recorded. (lineraliced acid dykes in a 1 000 foot hole drilled by Cyprus Mines had a total inter- section of almost 300 feet with an average crade of 0.4% copper. Surrounding drill holes at distances of 500 feet did not intersect +hese dykes. This group of drill holes occupies a small part of an area about 2 km by 1 km which was affected by intense quartz sericite pyrite alteration along many fractures with an associated soil copper anomaly. It may be that the quartz sericite alteraiion with feeble copper mineralisation represents hydrothermal alteration emanating `rom a mineralised intrusion of which the dykes mentioned above are off shoots.

Jan 1, 1978

By Ricardo Gomez, C. T. Ogryzlo, A. A. Dor

This paper reviews the historical background leading to the development of the project. It gives a description of the exploration program and resulting geological and ore reserve information together with plans for mining. A discussion is included of the three processes investigated for the project: 1. Rotary Hearth and Magnetic Concentration 2. Shaft Furnace and Electric Furnace 3. Rotary Kiln and Electric Furnace Results of pilot plant campaigns conducted at Fiskaa, Norway, and Riddle, Oregon, on the process chosen for the production of ferronickel are presented. The paper continues with a review of the considerations involved in selection of commercial plant equipment and concludes with comments on the current status of the project.

Jan 1, 1979

By T Vizcarra, G Sandoval, C L. Evans

One of the challenges in the development of mineral processing simulators is modelling the liberation characteristics of particles produced by comminution circuits. Understanding the mineral characteristics of these particles is one of the keys to predicting their behaviour in separation circuits. While more fundamental research seeks to model the non-random breakage of ores this work examines whether we can move forward now by using observed characteristics of ores to model the composition of particles generated in comminution processes. Several researchers have noted the similarity of the liberation characteristics for a selected size fraction of particulate material, whether the fraction comes from a coarse material, such as the product from a jaw crusher, or a more finely ground material, such as the product from a ball mill. In most cases these observations were reported as an aside and were not the main focus of the published work. This observed behaviour has the potential to be a useful tool for modelling the particle characteristics in mineral comminution and separation circuits, particularly as we move towards the development of multi-component models. However, before the behaviour can be used widely we need to understand which ore types follow the observed pattern and which do not. The current work examines a range of ores and identifies which exhibit the pattern of similarity of composition for particles in a given size class that has been produced as the result of a variety of breakage conditions. The impact of mineralogy and texture on the evolution of liberation characteristics for both valuable and gangue minerals is discussed.

Jan 1, 2008

By R. H. Pemberton

The principle of airborne electromagnetic prospecting is well-known. The basic geophysical texts in most cases discuss the main elements involved in electromagnetic prospecting. However, there is certainly little information available to the public concerning the present types of airborne electromagnetic systems being flown today by both contracting companies and some of the mining companies which have their own instruments. This is unfortunate since it is difficult for those people not conducting such operations to understand thoroughly the large variation in the electromagnetic instruments available.

Jan 1, 1961

By E Giles

Pike River Coal Limited (PRCL) is opening a new underground coal mine in the Paparoa Ranges north-east of Greymouth. To access the coal reserves, PRCL have had to build a 13 km access road through regrowth and virgin forest, and appointed McConnell Dowell Constructors Limited, with URS New Zealand Limited as their consulting engineers, to construct the final access link: a 2.3 km long, 5.5 m wide and 4.5 m high incline tunnel. This paper discusses the logistical issues of construction in an isolated pristine forest in mountain land and how they were addressed. It provides an overview of the 90 per cent complete tunnel and how challenging rock conditions have been mastered. It outlines briefly the remaining work which is construction of pit bottom workings where the mine infrastructure will be housed and construction of a 110 m deep, 4.0 m diameter, vertical ventilation shaft.

Jan 1, 2008

By Lyman GJ, Davis JJ

Models which have been presented in the literature consider only selected aspects of dense medium cyclone operation, are empirical in nature and generally relate only to severely limited ranges of operating parameters. This paper reports progress towards development of a more comprehensive and robust model. The data base consists of partitioning parameters developed using density tracers and conventional coal sampling and analysis techniques, together with recordings of parameters such as cyclone dimensions, feed pressure, medium size distribution and product media densities.. These data were drawn from 15 Australian coal preparation plants. To elucidate the effects of important operating parameters on medium behaviour and on the partitioning of large particles a series of pilot scale tests was also conducted. The present model consists of eight sub-models which relate to particular aspects of dense medium cyclone operation such as medium flowrates and densities, or size- by-size separation densities and Eps. The model structure follows a logical progression which clearly demonstrates the importance of understanding medium behaviour before attempting to predict partitioning performance. The model also attempts to define the conditions under which yield losses due to unstable "surging" discharge may occur.

Jan 1, 1987

By André Vervoort

In coal room and pillar, and pillar extraction panels, the sidewall conditions were investigated based on underground measurements and numerical simulations. Three-dimensional linear elastic models provided a useful and quick prediction of the amount of sidewall spalling. However, more complex constitutive models were required to simulate more accurately the extent of fracturing and its effect on the stress re-distribution. The input parameters of a Mohr-Coulomb model were determined by back-analysis of underground measurements, and the effect of the depth of the workings and the time dependent occcurrence of coal pillar fracturing were analyzed.

Jan 1, 1992

By Alan Morris

BRASS rod for use in automatic screw machines is one of the major products of the brass mills. A large tonnage is consumed each year in the manufacture of an endless variety of finished articles and parts for assembly into other products. The machines that do this work have been developed to a high degree of efficiency, and their manufacturers are still striving for higher production speeds. This development has brought with it a demand for brass rod to meet the increasingly difficult machining conditions. This paper is a report of the results of tests undertaken in an effort to obtain a measure of the effects of such variables as lead content, microstructure and cold work on the machinability of brass rod. It is realized that the term "machinability" has never been well defined. Power, finish and tool life all should have a place in such a. definition. In practice it is sometimes found necessary to sacrifice some of these in order to obtain a rod that will not tend to throw up a burr, or will give a burr which is easily tumbled off. Again a specially stiff rod may be necessary because of long overhang from the chuck or a rod of special characteristics is needed to take a given broaching operation without chattering. It is only through an understanding of the effect of basic mill operations on the machinability of the rod that such problems as these may be solved most economically. It is hoped that this paper, together with the discussion it may evoke, will prove to be a basis for such an understanding.

Jan 1, 1932

By A D. Bugarski, G H. Schnakenberg Jr

An investigation was carried out at a US underground mine to characterise diesel aerosols and to asses the effects of various control technologies on the concentrations and properties of particulate matter and gases emitted by heavy-duty diesel-powered equipment. This study was dedicated to evaluating the impact on mine air quality of contemporary diesel particulate filter (DPF) systems installed on mining equipment. Additional efforts were made to assess the effect of blended biodiesel fuels, yellow grease and soy, ultra-low sulfur fuel, a fuel emulsion and of selected diesel oxidation catalysts on air quality and emissions. The carbon analysis performed on the collected samples showed that the tested DPF systems reduced the mass concentrations of elemental carbon in mine air by between 70 per cent and 92 per cent. In addition, TEOM measurements, collected during these tests, showed that the total diesel particulate matter concentration in the mine air was reduced by greater than 65 per cent when DPF systems were used. The tested biodiesel blends were found to reduce elemental carbon concentrations in the mine air by between 49 per cent and 33 per cent, for the B20 (20 per cent biodiesel/80 per cent #2 diesel) of soy and yellow grease respectively and between 66 per cent and 56 per cent for the B50 (50 per cent biodiesel/50 per cent #2 diesel) of soy and yellow grease, respectively. The water-in-diesel fuel emulsion was shown to reduce elemental carbon concentrations by as much as 85 per cent. NO2 measurements showed an increase in the maximum concentrations of NO2 when catalysed DPF systems were used instead of mufflers.

Jan 1, 2005

By R. M. Brick, Arthur Phillips, A. J. Smith

A PREVIOUS publication1§ has described the effect of quenching stresses on the lattice parameter values of high-purity aluminum-copper alloys particularly with reference to the solution and precipitation of CuA12. A similar study has been made of the aluminum-rich aluminum-magnesium alloys. Attention has been directed in the present investigation. to the magnitude of the quenching stresses as affected by the specimen size and shape, the number of solute atoms and the quenching rate. The effect of cooling stresses in causing plastic deformation or cracking has been considered in relation to the physical properties of the alloy. On reheating alloys in the two-phase field, the time required for precipitation to occur has been observed in connection with the degree of supersaturation, the rate of diffusion of the solute atoms as a function of the comparative atomic radii, degree of strain, temperature of reheating and grain size. A few qualitative comparisons on the relative effect of these factors have been drawn between the aluminum-copper alloys and the aluminum-magnesium alloys. STRAIN IN SOLID-SOLUTION ALLOYS A 10 per cent magnesium alloy in the form of chill-cast bars was furnished by the Aluminum Company of America through the courtesy of L. W. Kempf. Additional alloys were prepared using aluminum (99.95 per cent Al) and high-grade magnesium. The alloys listed in Table 1 were melted in an Acheson graphite crucible under a flux of fused MgCl2, CaC12, NaCl. Chill-cast rods were sealed under vacuum

Jan 1, 1935

By Walter W. Bradley

Mining by hydraulic process of the important gold-bearing gravels of the Sacramento Valley in the basins of the Yuba, Bear and American rivers began in 1853, and continued at an ever-increasing rate for 30 years. In its most active days it reached an annual production of $15,000,000, and averaged $10,000,000 per year over the 30 years. During that period no provisions were made to prevent the debris from being discharged into the water courses, and ultimately large quantities of silt, sand and gravel were washed down to the lower valleys; filling channels, causing overflow of agricultural lands and difficulty in maintaining navigable depths in the Sacramento River. Agitation and suits filed because of these damages finally resulted in the injunction decision of Judge L. B. Sawyer,' in the U.S. Circuit Court, Jan. 23, 1884, which closed down practically all hydraulic mining operations not having means to restrain their debris. In 1893 (approved March 1, 1893), Congress passed the act introduced by Representative Anthony Caminetti, of California, creating the California Debris Commission, composed of three officers assigned from the Engineer Corps of the U.S. Army, and since that time it has been legal and possible within the drainage systems of Sacramento and San Joaquin rivers to conduct hydraulic mining of gold-bearing gravels behind dams built under this commission's permit and supervision. In the watersheds of the Trinity and Klamath rivers, which flow directly to the Pacific Ocean and do not affect navigation or agriculture, operating permits from the California Debris Commission are not required. There is a measure of restriction there, however, through what is known as the Trinity and Klamath River Fish and Game District. Chap. 215, Stat. 1931, in order to secure relatively clear water for the fishing season, provides that between July 15 and October 15 each year there must not be discharged into these rivers debris that will cause a turbidity greater than a content of 50 parts per million in the

Jan 1, 1937

By J. E. Korski

Quebec Cartier Mining Co. operates a low-grade iron ore deposit at Lac Jeannine, Que., which is located at the extreme southwestern end of the Quebec-Labrador Trough (Fig. 1). The facilities there include one of the world's largest concentrators, a hydroelectric plant of 60,000 hp, and the modern town of Gagnon. A 191-mile railway connects the mine to the seaport situated at Port Cartier on the St. Lawrence River. The harbor in Port Cartier can accommodate both lake and large ocean- going vessels and is also the site of a major grain terminal. The concentrator in Lac Jeannine is designed to produce some 8 million tpy (tons per year) of specular hematite concentrate, containing 66% Fe, from approximately 20 million tons of crude ore. An annual stripping program of 5 to 8 million cu yd of waste rock uncovers the required ore. Approximately 100,000 tons of ore and waste are removed daily on a year-round, 24-hr-per-day basis. The open pit covers an area with maximum dimensions of 8,000 x 2,600 ft (Fig. 2). Present mining plans call for an ultimate depth of approximately 1,000 ft below original ground level. The rocks in the pit area are typical of this portion of the Grenville geological province. They consist largely of marble, quartz rock, pegmatite, iron formation, and stratigraphically older gneisses. The iron-ore formation consists of medium to coarse-grained specular hematite in a quartz host rock. The formation occurs locally in a plunging, anticlinal form. The topography in the vicinity of the mine is rolling, with maximum variations in elevation of about 400 ft. The hills are thickly wooded with birch, black spruce, and some tamarack. Lakes and muskeg areas are plentiful. Precipitation and temperature records have been kept since 1959. The annual rainfall has ranged between a low of 23 in. and a high of 42 in.

Jan 1, 1969

By E. L. McHugh

Digital camera and computer technologies can be used to monitor mine slopes and provide real-time warning of rock falls. NIOSH researchers assembled a surveillance system using low-cost video cameras and computer software from the security industry to test its effectiveness. The system is designed to signal an alarm when motion is detected and to record images of the scene. Masking can restrict motion detection to specific areas within the camera view; sensitivity is adjustable. The time-stamped images provide a record that can help reconstruct and quantify an event. Video motion detection can augment standard monitoring methods to increase safety in surface mines.

Jan 1, 2004

LIST OF MEMBERS AND ASSOCIATES ARRANGED ACCORDING TO STATES AND TOWNS. ALABAMA. Aldrich, Aldrich, W. F. Anniston, Noble, A. E Bessemer, Fergusson, V. Bir¬mingham, Aldrich, T. H., Jr, Bowron, C. E, Bowron, J., Davis, F H, Dimmick, F. D., Hillman, Ludwig, C. P., McCarthy, M. E, McCormack, G B., McCrery, Ramsay, E, Shook, A. M. Ensley, McDonald, S., Shook, J. W. Gadsden, Lee, R. H., Jr. Gannts Quarry, Hiller, E Helena, Squire, J. Huntsvalle, Moss Le¬high, Toulmin. Ozmoor, Greenamyer, A. G. Rock Run, Garvin, J M. Selma, Saylor, B. F. A. Sheffield, Miller, D, I. Tuscaloosa, Lodge, J. Woodward, Wood¬ward, A. H. ALASKA Coppermount, Wiswell, H. J. Douglas Island, Macdonald, J Ellamar, Stevens, B. Fairbanks, Hamilton, A L Haines, Le Wald, E A. Jualin, Hoggatt, W. B. Juneau, Denby, Hampton, W. H , Thane, B L , Whipple, J. R. Ketchikan, Bar¬ber, J C , Parker, J. L., Reid, G D Nome, Garfield, C D. Snettwham, Tisdale. Teller, Hirshberg, M. R. Treadwell Caty, Kinzie, Stow, H. P. Valdez, Esterly, G. M, Hazelet.

Jan 1, 1910

By Brent Wilkins

The project team was tasked with the design and installation of a deep foundation system to support an expansion to a power generating station in Glenrock WY. Cast-in-place piles installed by a fixed mast drilling platform were assessed to be the most efficient foundation system for the subgrade conditions and range of design loads for the project. It was determined that conventional augered, cast-in-place piles could not be installed to the required pile toe elevations. Subsurface materials consisted of interbedded coarse- and fine-grained soils to about 23 ft to 30 ft depth below the ground surface, underlain by carbonaceous shale (claystone) with interbedded sandstone. The overburden materials varied from very soft to medium stiff and loose to dense. The claystone was typically foliated and very weak to weak whereas the sandstone was typically massive and very weak to weak. The site characterization consisted of a variety of field and laboratory programs including soil borings with Standard Penetration Tests, pressure-meter testing, and geophysical testing. A load test program was performed involving the compressive, lateral, and tensile testing of piles ranging from 14-in to 24-in diameter. Compression test piles were instrumented with vibrating wire strain gages. The paper includes a discussion of the regional and local geologic and geotechnical parameters, particularly the results of the various in situ and laboratory test programs. The selected foundation system is introduced. Load test results are then presented along with analysis and discussion of these results with regard to performance of the piles in the claystone.

Jan 1, 2009

By David B. Rushmore

Torches were used by the early Romans for mine-lighting, and these were followed by open lamps or earthen jars filled with tallow or oil, and later by candles. In early coal-mining, explosive gases seldom occurred, and, if they were encountered, the danger of explosion was materially diminished by the absence of any ventilating-system and the consequent insufficient circulation of air to form with the methane an explosive mixture. As the art advanced, the danger of fire-damp became more apparent, and methods for testing the air were resorted to as early as in the fifteenth century. The method of testing consisted in lowering a dog in a basket down the shaft. As soon as he encountered fire-damp he would commence to howl, after which he was withdrawn, and a leafy bush was fastened to the end of the rope and run rapidly up and down the shaft. This so disturbed the accumulation of gas as to cause it to rise out of the shaft. Later this odd method of testing was improved upon through the discovery that a light inserted in a body of fire-damp Gould produce a blue flame. Candles were used for this purpose, and, when fire-damp was thus discovered, brushing or some other primitive method of fanning was resorted to for driving out the gas. In some instances the gas was burned away, regardless of the danger thereby incurred. A man, wearing a well-moistened coat and a mask with glass spectacles, descended in the mine a few hours before each shift. With a long stick, to which was fastened a burning torch or candle, he would crawl on the floor with the stick so raised that the light would sweep the roof and ignite the gas which it encountered. In this position the flame of the explosion would pass over him, after which he would retreat from the gases resulting from the combustion. The occurrence of serious accidents resulted in

Jan 1, 1913

By Paul F. Kerr

Uranium mineralization occurs in the footwall of the Sunshine vein from the 2900 to the 3700 level. Veinlets of uraninite associated with pyrite and jasper have been so extensively divided and recemented that units more than a few feet in length are seldom observed. The wall rock is St. Regis quartzite of the Belt series. The age of the uraninite, on the basis of isotopic analyses, is 750 t- 50, which agrees with geological data suggesting that phases of the Sunshine mineralization are pre-Cambrian.

Jan 5, 1953

By S. Hodgson

Introduction The Red Dog zinc/lead deposit in northwest Alaska is the second largest zinc deposit ever discovered. Being developed by Cominco Alaska, with startup scheduled for early 1990, it will ultimately be the largest zinc mine in the Western World. Table 1 shows the reserves of the deposit. Bob Baker, a local bush pilot, discovered Red Dog in 1968. The US Geological Survey assessed the find. But the Red Dog site had been withdrawn from staking by provisions in the Alaska Native Claims Settlement Act of 1971 (ANCSA). Under the terms of ANCSA, the deposit was selected by the NANA Regional Corporation, one of 13 native corporations established by the Act. Then, in 1980, the US Congress confirmed this selection, in the Alaska National Interest Lands Conservation Act. In 1982, Cominco and NANA reached an agreement that has led to the development of the mine. Under the agreement, Cominco leases the property from NANA, develops and operates the mine, and markets the concentrate produced. In return, NANA receives royalties and, after capital recovery, participates in the net proceeds from the operation. The Alaska State Government is also playing a role in the development of the mine. Under the auspices of the Alaska Industrial Development Authority (AIDA), the state will construct, own, and operate the DeLong Mountains Regional Transportation System. This consists of a 84-km (52¬mile) road from the minesite to the Chukchi Sea. Located here are the port facilities necessary to store and ship the annual concentrate production and receive the mine fuel and supplies. For using this transportation system, Cominco will pay an annual toll fee. Over the anticipated 50 year life of the operation, the fee will provide a 6.5% return to the State of Alaska. In late 1986, Cominco's Board of Directors approved the Red Dog project. And, during the summer of 1987, road construction began. In February 1988, initial stripping began at the ore body and construction started at the millsite. Project setting The project site is approximately 1000 km (600 miles) northwest of Anchorage, 84 km (52 miles) east of tidewater on the Chukchi Sea, and 192 km (120 miles) north of the Arctic Circle (Fig. 1). The countryside consists of low, rolling hills that lead into mountains north and east of the deposit. The vegetation is typical tundra mat. And the site is in an area of permafrost. However, the permafrost is relatively warm and some areas have been found to be thawed. Examples would be creek bottoms and the site of the main waste dump.

Jan 12, 1988