Search Documents

By C. M. Díaz, P. J. Mackey, P. Coursol

In a recent paper [1], the present authors discussed calculated energy consumption numbers in copper sulphide concentrate smelting for four different smelting technologies. For the present study, from among these technologies, they selected the Noranda/Teniente continuous bath smelting followed by Peirce Smith (PS) converting route to investigate the impact on total energy requirement of some key process variations, such as tuyere injection of dry concentrate vs. slingering of wet concentrate over the molten bath, continuous converting vs. conventional batch PS converting and commercially proven slag cleaning alternatives. In their calculations, the authors used the same thermochemical model and methodology used in their earlier paper. This approach to explore plant design options provides an interesting basis for evaluating flowsheet modifications that could lead to significant copper smelting energy savings. The METSIM software was used in the present paper to carry out heat and mass balance computations for 8 different flowsheet configurations. The results are presented and discussed in the paper with respect to copper recoveries, energy requirements and CO2 emissions.

Jan 1, 2011

By X. Xu, J. K. -W. Wong, J. -Y. Delenne, K. Soga

Hydraulic fracturing (HF) is a mulit-scale and multi-physics process which makes numerical modelling challenging. Conventional numerical models focus on multi-physics nature of HF but the multiscale nature is compromised by idealization of reservoir to be continuous, homogeneous and isotropic. However, natural fractures take a significant role in the success of HF for exploration of unconventional resources like Shale gas. Advancement in microseismic monitoring provides useful data for simulation in a much greater details. There is an urgent need to develop a suitable numerical tool for multi-scale threedimensional simulation to better understand the roles of discontinuities and heterogeneity in reservoir and its interaction with HF, especially to address the environmental concerns such as induced seismicity. In this paper, a simple discontinuum numerical method – Lattice Element Method (LEM) is proposed to model HF in a large scale three-dimensional model. A reservoir is modelled as a lattice network composed of 1D Hookean’s spring. Fracturing is modelled simply by removing lattices that meet a specified threshold as determined by the critical energy release rate of the rock. By introducing disorder in the model, mesh dependency in modelling fracture growth is minimized. Fluid flow is simplified as flow in pipe network and the permeability of pipe is related to fracture aperture by cubic flow law. Therefore, fracture flow and rock deformation are fully coupled. In this paper, four simulations of the same configuration except with different degrees of reservoir heterogeneity are presented. Fractures formed are diffusive and two groups of fracture are identified – connected fractures and isolated fracture without clear spatial correlation. The former forms a ‘fracture cloud’ and contributes to fluid flow and modeled by pipe network. The flow of fluid is highly tortuous and pipe network is sparely connected. The degree of reservoir heterogeneity controls the growth of ‘fracture cloud’ and pipe network. Microseismic monitoring often shows diffusive fracturing during HF on site and hence the outcome of the proposed model can be compared to such monitoring results.

Jan 1, 2015

By J. J. Hussey

"Abstract-The ""Brunswick Horizon"" an informally named ore-bearing unit near the top of the Nepisiguit Falls Formation in the Ordovician Tetagouche Group, hosts the Brunswick No. 6 and No. 12 base-metal mines, as well as the former Austin Brook iron mine, in northern New Brunswick. Detailed structural analysis of the No. 6 and No.12 mines led to the prediction that a massive­ sulfide deposit may have been repeated by F1 folding along the Brunswick Horizon. A subsequent drilling program discovered the new massive-sulfide North End Zone at a vertical depth of 1100 m, 1 km north of the No. 12 underground workings. By the end of 1990, Zn-Pb-rich massive sulfides had been delineated over a strike length of 200 m and a down-dip extent of 170 m. Rock units intersected in the North End Zone are generally thinner and vary somewhat from those at the Brunswick No. 12 mine. Thinning of the hanging wall rocks may be primary, may result from attenuation along F2 folds, or may represent truncation by a thrust fault. The newly discovered sulfide zone indicates that significant potential exists for the discovery of other deposits at previously unexplored depths.SOMMAIRE-Dans le nord-est du Nouveau-Brunswick ""l'horizon Brunswick"" est le nom usuel de la zone qui contient les mines de métaux de base Brunswick No. 6 et No. 12, ainsi que l'ancienne mine de fer Austin Brook, toutes situées sur le dessus de la Formation ""Nepisiguit Falls"" dans le Groupe Tetagouche d'âge Ordovicien. Une analyse détaillée de la structure des mines No. 6 et No. 12 à permis a van Staal de prédire qu'un gîte de sulfures massifs pourrait se répéter dû à une déformation F1, au nord de Brunswick No. 12. Suite à un programme de forage, la nouvelle zone de sulfures massifs appelée le ""North End Zone"", profonde de 1100 rn, et à une distance d'un km au nord des chantiers souterrains, fut découverte vers la fin de l'année 1990, les sulfures massifs riches en Zn-Pb ont été délimités sur une longueur de 200 rn et une hauteur de 170 rn le long du pendage. Les unités de roches intersectées dans le ""North End Zone"" sont généralement plus minces et sont quelque peu différentes de celles de la mine Brunswick No. 12. L'amin­ cissement des roches pourrait être primaire ou être le résultat de l'atténuation le long des plis F2, ou soit tronqué par une faille. La nouvelle découverte d'une zone de sulfures indique un potentiel énorme pour la découverte d'autres g ""tes à ces profondeurs inexplorées."

Jan 1, 1992

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. Contrary to most copper sulfide minerals where recovery is principally liberation controlled, the recovery of molybdenite is much more complex with fully liberated particles commonly lost to tailings. It is this complexity that facilitated the necessity for a geometallurgical investigation of molybdenite from the Bingham Canyon deposit. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes (i.e. morphology, angularity, liberation, size) have on the recovery of molybdenite in the processing circuit. A set of samples was collected from the ores and products produced by Rio Tinto Kennecott’s Copperton Concentrator. All samples were analyzed using normal polarized reflective light, Mineral Liberation Analyzer (MLA) and X-ray diffractometery (XRD) techniques. The results of this investigation revealed the presence of two distinctly different types of molybdenite, which have been identified as the two polytypes of molybdenite, i.e. hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the core of the Bingham Canyon deposit. The 3R polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Concerning their metallurgical behavior each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. For instance, the 2H polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high quality molybdenum concentrate under normal operating conditions common to most copper concentration operations. In contrast, the 3R polytype is difficult to grind and kinetically “slower” floating with surface attributes that less amenable to recovery under normal operating conditions. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to the normal operating parameters may be necessary to improve the recovery of molybdenum. Finally, a preliminary investigation into the metal budget of porphyry Cu and Mo deposits indicates that a positive correlation may exist between the total economic metal budget and the polytype content. For example, higher concentrations of the 3R polytype appear to be more prevalent in Au-enriched porphyries versus Mo-enriched porphyries. This observation may also serve to help explain why it is easier to obtain high rates of recovery in Mo ± W-rich deposits, which contain little to none of the 3R-polytype. Consequently, the potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present, as well as its impact on the economics (exploration) and/or on the processing circuit (plant design) could exist. In conclusion, this investigation highlights the necessity of understanding the mineralogical properties or characteristics of molybdenite and/or other economic mineral(s), as these can and will have a direct impact upon the performance and plant optimization."

Jan 1, 2016

By K. K. Kohli

Since the adoption of the Surface Mining Reclamation and Control Act of 1977, which mandates that surface subsidence be an intergral part of the underground coal mine design, there has been a sudden rise of demand on guidelines for minimizing surface subsidence and its associated structural damages. Unfortunately there is no sufficient amount of systematic subsidence data to fill such a gap, although considerable research has been devoted to the subsidence-induced damages of surface structures in the past. However, it was said that many surface subsidence surveys have been performed and monitored by coal companies during the past twenty years, and that it will be a great source of information for subsidence engineering design if they can be collected and assembled together. An effort was therefore initiated in the Department of Mining Engineering, West Virginia University, under contract with the U. S. Bureau of Mines in December 1978 to contact each individual coal company in the Northern Appalachian Coal Field for any surface subsidence survey data. After 10 months' survey, the data collected include 17 longwall panels and 2 room and pillar sections. The data in-each panel and section cover the complete set of subsidence survey raw data, underground mine layout maps, surface topo maps, geological loggings showing the stratigraphic sequences and thickness of the overburden, and if available, locations and types of surface structures. On-site visits were followed to study the surface terraines and structures. Interviews were conducted with the owners of the surface structures in most cases about, if any, the history and characteristics of damages.

Jan 1, 1980

Based on experimental and computer simulation results from our group, we report a systematic, atomic level analysis of carbon dissolution from carbonaceous materials in molten iron. Experimental results on graphite / Fe-C-S system were obtained using carbon dissolution studies, XRD and FESEM investigations and were supplemented with Monte Carlo simulations. Three basic mechanisms, namely carbon atom dissociation rate, interfacial phenomena and mass transfer in the melt were found to be responsible for the overall dissolution process. While mass transfer in the melt is governed by the concentration gradients, melt composition and temperature; impurities present in ash play a significant role in the interfacial phenomena. For less ordered forms of carbonaceous materials, carbon atom dissociation rate depends strongly on the degree of long-range order and is an important rate controlling mechanism in the overall dissolution process. A systematic comparison of dissolution rates for a variety of coal-chars, natural and synthetic graphites has been carried out in an attempt to identify rate-controlling mechanisms. The structure of the carbonaceous material appears to be an important underlying factor in the carbon dissolution process.

Jan 1, 2003

By John F. Abel

Convergence measurement across the 17.4 m (57ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 by 9.6 m (38 by 31 1/2 ft) I.D. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2 3/4 in.) and 5.7 cm (2 1/4 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1984

By N. Kanari

One of the criteria to define the market value of chromite concentrate is its chromium to iron ratio. Changing this ratio for a definite chromite mineral is impossible by physical processing. This study investigated the possibility of increasing this ratio through the carbochlorination and the oxychlorination of chromite concentrates. Experiments are carried out up to 1000 °C. The characteristics of samples and reaction products are determined by SEM, XRD and chemical analysis. The carbochlorination of a chromite concentrate at about 600 °C leads to the . selective partial elimination of iron allowing a higher Cr/Fe ratio of the treated concentrate. Selective extraction of iron could also be achieved at about 950 °C by oxychlorination. In this case, a part of chromium contained in the concentrate is recovered as chromium oxychloride. The obtained residue had high content of Cr, Mg and A1 oxides. Such material has probably better chemical and thermal properties that may. be useful for foundary and refractory applications. Two flow-sheets for the beneficiation of the chromite concentrates using carho- and oxychlorination are suggested.

Jan 1, 1997

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

By Charles M. Wilk

"Solidification/stabilization (S/S) treatment is used to treat hazardous wastes for disposal and in the remediation/site restoration of contaminated land . SIS is also an increasingly popular technology for Brownfield (industrial property) redevelopment, since treated wastes can often be left on-site and to improve the soil for subsequent construction. This paper discusses the applicability of the technology to various wastes, basic cement chemistry relating to SIS, tests used to design treatability studies and to verify treatment, basics on implementation of the technology in the field , and examples of SIS use at brownfield sites, including a former wood preserving site, former manufactured gas plant sites, a former electric generating station, and a shopping mall development.INTRODUCTIONSolidification/Stabilization (S/S) is a widely used treatment for the management/disposal of a broad range of contaminated media and wastes; particularly those contaminated with substances classified as hazardous in the United States. The treatment involves mixing a binding reagent into the contaminated media or waste. The treatment protects human health and the environment by immobilizing contaminants within the treated material. Immobilization within the treated material prevents migration of the contaminants to human, animal and plant receptors. SIS treatment has been used to treat radioactive wastes since the 1950s and hazardous waste since the 1970's (Conner 1990). SIS continues as a cornerstone treatment technology for the management of radioactive waste, hazardous waste, and site remediation and Brownfield redevelopment."

Jan 1, 2005

By J. E. Miller

The development of a new means of measuring the relative abrasivity of a slurry came about by necessity in 1967 during a full scale loop test of a 560 H.P. reciprocating pump handling magnetite slurry. In order to evaluate the life of expendable fluid end parts, the question of the amount of attrition in a re-circulated slurry had to be considered. An expected reduction in abrasivity as a result of this attrition would certainly give erroneous data on a parts life test. There- fore, some means of measuring such change in abrasivity became imperative. Several test methods were investigated1 but it was felt that these did not fully represent the wear due to back and forth rubbing action associated with a reciprocating pump. A "rubbing block" device used some years ago to determine the quality of hard facing materials was recalled, along with its shortcomings, in that an attempt was made to suspend a small percentage of abrasive particles in a colloidal viscous "mud". Erratic results were attributed to the fact that it was difficult to maintain a consistent slurry concentration under the metal wear block and the reciprocating speed was not great enough to maintain good agitation.

Jan 1, 1973

ABSTRACT It is critical that historical processes and concomitant exposures to specific nickel substances be understood because some diseases linked to inhalation of certain nickel-containing substances have a long latency between first exposure and disease onset, and because nickel substances vary significantly in their toxicological properties. A discussion of the smelting history and related processes at Vale Canada’s (Inco’s) Copper Cliff, Ontario, smelter is integral to the understanding of these processes. The post-1950 processing history, equipment, propensity for aerosol formation, operational procedures, and ventilation controls used by Vale Canada in roasting, smelting, converting, and copper-nickel separation is discussed.

Jan 1, 2013

By Ram V. Ramachandran

As an industry with major potential impacts (both good and bad) on water resources and due to the rising costs of process water, the mining and metallurgical processing industry has a key responsibility to contribute to the overall goal of preserving both the quantity and quality of water available within the watersheds they operate in. As we plan for new and existing mining and metallurgical projects, we need to consider a hierarchy of options to minimize our impact within the watersheds we operate; keeping clean water clean by diverting around our operations; reduction in the amount of water we use; reuse of water wherever possible, and improvements to water quality for recycling and/or release to environment. Technology is needed to treat water to improve its quality for reuse or release to the original watershed. While lime precipitation followed by sulfide polishing is effective for removal of most of the metals, it does little or nothing to remove ammonium ions and anions such as chloride, nitrate, molybdate, arsenate and selenite/selenite. Regulations on sulfate limits in treated discharge water has drawn close attention to the treatment of acid mine drainage (AMD). Management of brine and salt disposal is also posing a problem due to strict regulations and cost of disposal. This paper will: (a) address issues associated with managing water with the objective of maintaining water sheds—status quo-during and after operation (b) discuss potential technologies for advanced water treatment plants.

By K. Darcovich

The wettabilities of agglomerates made from coals of several different ranks were measured by the adhesion technique. Oil levels from 0 to 10% by weight were used. As was expected, it was found that higher-rank coals are more easily oil-wetted and that the surface properties of the agglomerates correlate with agglomeration recovery and ash removal data.

Jan 1, 1992

By Alan Boughey

The world's largest grinding mill operates at the Cadia Hill Mine in Australia. Svedala Industries supplied the 12.2-m- (40-ft-) diam, 20-MW Cadia gearless, semiautogenous grinding mill (SAG). This was a leap of more than 40% above the largest operating SAG mill. This article reviews the significant items involved in the development, design, manufacture, installation and operation of this mill. Description of the Cadia project The Cadia Hill Mine is located 25 km (15 miles) southwest of Orange, in the Central Tablelands of New South Wales, Australia. The mining lease covers about 3,100 hm2 (7,660 acres) of the Cadia Valley. The Cadia deposit is a large, homogeneous, low-grade, porphyry-type, gold-copper resource. Current reserves stand at 202 Mt (222 million st), grading 0.73 g/t (0.02 oz/st) gold and 0.17% copper. They contain 146.2 t (4.7 million oz) of gold and 347 Kt (382,500 st) of copper. The operation consists of openpit mining and ore processing to produce gold bullion and a gold/copper concentrate. The operation processes 17 Mt/a (19 millon stpy) of ore to produce 91 kt/a (100,300 stpy) of concentrate and 9.1 t/a (293,000 oz/year) of gold. The plant operates two 12-hour shifts a day and had a targeted availability of 94%. The plant facilities include a copper concentrator, o water supply system, an openpit mine, tailings pipeline and dam, and a concentrate pipeline and dewatering facility located in Blayney, about 35 km (22 miles) from the concentrator. Significant features of the process plant include o primary crusher and stockpile, a reclaim conveyor system feeding, the Cadia SAG mill (Figs. 1 and 2) and two 6.7-m- (22-ft-) diam ball mills (Fig. 3). A portion of the gold is extracted in a gravity circuit. The balance is extracted with the copper in the flotation section of the plant. Concentrate is thickened and piped about 35 km (22 miles) to the filter plant and rail loadout facility located in Blayney. Tailings are pumped to a tailings dam and process water is reclaimed from the tailings dam. The water system is designed to control and capture available runoff from local creeks, and to store these waters in dams and weirs. In addition, a major portion of the water for the process plant is treated effluent from the city of Orange and a smaller portion from Blayney Mill selection. The low-grade ore posed a dilemma for Cadia. To achieve a satisfactory economic operation, large-scale processing was required. The selection of the mills, equal to the largest designed and operated at the time, gave a plant configuration consisting of two 11.1- x 5.8-m (36- x 19-ft) SAG mills and three 6.1- x 9.1-m (20 x 30-ft) ball mills. This configuration did not provide the most satisfactory economic model for the project. A review of the single line configuration indicated that a significant reduction in the overall capital cost of the plant could be achieved by increasing the size of the mills and reducing the quantity. Increasing the size of the mills,

Jan 1, 2001

By Andrea Gambi, Giancarlo Olivucci, Maurizio Lenzi

"In the paper a criterion for the evaluation of the sharing of the lateral loads in a piled foundation is presented. It relies on the the compatibility condition between the rotation of the rigid pile cap and the rotations of the pile heads, following in that the criterion suggested by the Eurocode 8 - Part 5. This assumption leads to an analytical solutions which allows to deal with the sharing of the lateral loads and moments by means of two main interaction parameters only. A sharing domain is also derived and it shows the role played by the eccentricity of the lateral load on the values of the axial forces and of the bending moments at the head of the piles.INTRODUCTIONIt is well known that the interaction among soil, piles and foundation is one of the most complex subject to deal with in Geotechnical Engineering. Its rigorous study needs to employ suitable finite element software nowadays available and able to take into account the non linear behavior of the soil as a continuum and the inelastic response of the structure. A deep insight to the topic of the sharing of the loads cannot obviously renounce to this approach.On the other hand it is a daily need of the designers to have at their disposal simple tools that allow to make preliminary evaluations of the basic equilibrium conditions. To this purpose many methods of analysis have been developed in the past to face the sharing of the loads in a simplified version. The present contribution follows this way trying however to introduce some improvements that leads to find a solution that satisfies both the equilibrium of the forces and the compatibility of the movements (Lenzi, Gambi, Olivucci, 2002). The proposed model allows to identify the basic parameters which govern the sharing of the lateral load and it allows to perform also parametric analysis and quick checks that may be useful in the design of the piles."

Jan 1, 2005

By Š. Šachlová, T. Lokajícek, M. Petružálek, T. Svitek, A. Štastná

During the past 20 years, alkali silicate reaction (ASR) as a cause of concrete deterioration has been studied by a wide range of experimental methods such as microstructural and macrostructural analysis, bulk chemical analysis, X-ray and neutron diffraction analysis, etc. All of these data are compared with expansion values of mortar bars (following ASTM standard C 1260). Recent studies indicate the useful application of non-destructive methods with the aim of better reflecting mechanical properties and the degree of deterioration of real concrete. Ultrasonic testing methods (including ultrasonic pulse velocity UPV) are widely used to determine material mechanical properties and the changes induced by a variety of mechanical or chemical processes. However, only a few laboratory studies of ASR focused on ultrasonic testing of mortar bars. Due to this fact, a heating chamber was designed and constructed to enable ultrasonic sounding of mortar bar specimens while stored in accelerating solution. Regular ultrasonic sounding of mortar bars reveals significant dependence of ultrasonic data such as longitudinal P-wave velocity, signal energy, signal amplitude and signal frequency on mortar bar storage time. Ultrasonic data were subjected to time domain as well as frequency domain analysis. Different storage conditions were used to determine the effect of ASR on ultrasonic parameters. Mortar bars, prepared in the same manner with one type of aggregate, were stored in cold or warm water or in an accelerating warm medium. Ultrasonic data accurately reflects the differences in hardening and deterioration of tested mortar bars due to different storage conditions. Ultrasonic results showed very good correlation with the results of ASTM standard expansion tests and much higher sensitivity to ASR-induced concrete deterioration. Expansion tests showed 1% measured length differences in comparison with up to 80% resolution of ultrasonic data. The ultrasonic testing proved to be a suitable laboratory method for investigating ASR-related processes and could lead to an improvement of standard testing procedures.

Jan 1, 2015

By N. Novikov, M. Jastrzebski, N. Kryzhanovskaya, D. Shevchenko, I. Kapran, N. V. Novikov, T. Koehler, B. Zaporozhets

"The PFK FeNi Smelter was re-commissioned by Solway Resources in 2002, ending a long period of economic decline in the adjacent town. In 2009 Hatch was retained to design, supply and install a custom furnace crucible that would accommodate a capacity increase from 34 MW to 40 MW and increase campaign life through binding and cooling technologies, as part of ongoing improvement efforts. The involvement of PFK personnel was critical to the successful integration of the new furnace technology with the existing process and operational practice. The furnace upgrade project was completed in 18 months during 2010 – 2011. Since start-up, the furnace has exceeded production expectations, operating successfully at 42 MW.INTRODUCTIONAfter ceasing operations in the 1990’s, the Pobuzhsky Ferronickel Combine (PFK), located in central Ukraine, was stripped of useful equipment and deteriorated while dormant. The surrounding town experienced a period of economic decline throughout the 1990’s. Solway Industries purchased the complex in 2002 and began a systematic incremental program to re-commission the smelter using both local expertise and specialists from other parts of the former Soviet Union. This led to the re-birth of PFK as a successful toll-smelting complex, and a renaissance for the surrounding economy.As part of the continuing improvement program, PFK approached Hatch in 2009 to study the possibility of a capacity expansion from 34 MW to 40 MW. It was decided, based on the results of the study, to design and install a custom furnace crucible integrating the unique PFK FeNi process with modern Hatch furnace technology. This novel approach had many benefits, including: maximum re-use of existing furnace components (off-gas, feed equipment and transformers), minimal impact on upstream and downstream equipment and building structure, and the retention of a familiar operating regime. The latter was a key factor in the success of the project, as it allowed the extensive operating expertise of the PFK staff to remain highly relevant to the upgraded furnace. This led to minimized capital investment, a rapid start-up and no significant operational challenges switching over to the new equipment incorporating Hatch furnace technology."

Jan 1, 2012

By David R. Maneval

At the turn of the century the keys to industrial success were coal and iron. At that time, Pennsylvania was the ranking mineral producer among the States and close to 90% of the Nations energy output was generated by coal. The growth of this Common-wealth into the greatest industrial State in the nation has been due to the huge resources of easily accessable coal found by the early settlers. It was the development of these deposits that provided the United States with a new source of fuel energy. For nearly a century, the Commonwealth was the chief powerhouse of our nation and the chief source of its industrial blood and bone. In 1928 it was truly said that coal was king in Pennsylvania. Pennsylvania that year mined a billion dollars worth of coal. A single train carrying this output would reach more than twice around the world at the latitude of Pennsylvania. Coal formed nearly 67% of the freight of Pennsylvania and was responsible for its four billion dollar iron and steel industry. Coal was the real reason why Pennsylvania although 32nd in size was second and not tenth or fifteenth in wealth, population and industry. Pennsylvania was slow to take-up her heritage as the greatest coal producing State in the union. But the knowledge that coal was present was not slow in accumulating. In fact the Indians were aware of its existence long before the white man arrived. They knew that many of the hills were underlain with black stones that would burn. It is reasonably certain that Arnold Viele, the first white man to cross the mountain in this State saw coal in them in 1692. But awareness was not enough. The population in these days was confined to southeastern corner of the State and the population at this time had little need or interest in the resources further inland. Pennsylvania anthracite was discovered in 1762 but was first regarded only as a curiosity. Commercial productions started in 1820. This stimulated the development of many native industries and extensive canal system and afterwards an elaborate net-work of railroads were constructed at great costs to bring the products of the hard

Jan 1, 1971

By Stephen P. Holt

In the fall of 1946 and spring of 1947 the Bureau of Mines put down five inclined diamond-drill holes totaling about 3,100 feet of bore to test for the possible eastward extension of the Royal Princess ore deposit in Jo Daviess County, Ill. Attention of the .Bureau was first directed to this property by the Illinois State Geological Survey. The history of production of the Royal. Princess mine and reports as to the size and nature of the deposit were considered justification for investigating the trend of the mineralization. This report describes the work done by the Bureau of Mines and presents the data obtained.

Jan 1, 1948