Search Documents

By A. Singh, R. D. Govender

The current method employed to quantify the efficiency of separation of ferromagnetic ores by wet low intensity magnetic drum separators (WLIMS) incorporates the use of a conventional benchscale Davis Tube (DT) operating at a magnetic field intensity that is equivalent to that of the drum’s surface. However, empirical research has indicated that the magnetic force, or force index, rather than the magnetic field intensity, is the critical factor in the operation of the magnetic separator (Murariu and Svoboda, 2002). Furthermore, the current aforementioned practice would yield incorrect information as the magnetic field gradients produced by a typical WLIMS unit differs considerably from that of a bench-scale DT. In light of this, research on magnetite focusing primarily on the scale-up of DT results to pilotscale WLIMS were undertaken. The investigation entailed a comparative study between that of a typical WLIMS circuit and a bench-scale DT. The purpose was to practically evaluate the performance of a WLIMS, bench-marked against the traditional laboratory-scale DT unit. Moreover, the secondary objective was to produce a magnetite concentrate graded at 69% Fe, 95% -45μm, as a suitable source of separation media for use in the Dense Medium Separation (DMS) industry. Fundamental findings of previous works provided a framework for the study, however, a realworld approach was explored. Preliminary testwork conducted at Mintek investigated the performance of a DT and a typical multi-stage laboratory-scale WLIMS circuit (operating at 1000 Gauss at the surface). The results attained indicated that a DT operating at high intensities is comparable to a single rougher WLIMS stage. Additionally, it was observed that the three stage laboratory-scale WLIMS circuit performed similarly to the DT operating at 1000 Gauss. Moreover, piloting testwork was undertaken, carried out in larger 380mm drums, and the results attained showed a strong correlation with laboratory-scale findings. Keywords: Davis Tube, wet low intensity magnetic separation, magnetite

Jan 1, 2020

By T. Bui, T. Wallmach, S. B. Blancher, A. Back, M. Pierre, V. Delarue, A. Kanzari

This study investigates nickel laterite porosity and its impact on geometallurgical modelling. We performed a detailed mineralogical study on a set of Ni-laterite samples originating from New Caledonia. Samples were analysed after heavy liquid separation by automated SEM (QEMSCAN®). Laboratory and QEMSCAN® modelling results do not correlate well. Ideal physical mineral properties such as mineral densities used in QEMSCAN® modelling do not match the actual physical densities of minerals. The presence of empty or water-filled pores can represent important amounts in minerals and change the overall density of a particle. An adequate modelling of real density separation of minerals and particles should consider the water-filled pores. The first step towards a better simulation was to integrate pores larger than 10 μm in diameter filled with water (density of 1 g/cm3) in the QEMSCAN® database. The results approached, but did not match the physical laboratory results. The second step was to identify nanometer to micrometer sized pores, which could not be identified by QEMSCAN®. It was possible to identify nanometric pores in enstatite, Fe-oxides, serpentine, talc and quartz, and radial aggregates of fibrous Fe-oxyhydroxides with high resolution SEM (HR-SEM). The quantification of those micro-sized pores was performed on 2D HR-SEM images using image-processing techniques developed in Python to calculate the nanometer to micrometer scale pores in each mineral. Despite the limitation of converting 2D imaging into 3D objects, in our case pore sizes and porosities, we were able to calculate a mean value of porosity for each mineral. The integration of this porosity in the calculation of particle densities yielded a good match between the QEMSCAN® model and the laboratory experiment results. Despite the complexity of a strongly weathered material, such as Ni-laterites, a good knowledge of the ore makes it possible to build reliable processing models. Keywords: Mineralogy, geometallurgy, nickel laterites, SEM, QEMSCAN®, porosity, density

Jan 1, 2020

By F. Dong, F. Yang, J. Wang, Z. Wang, D. Mingxia

Antimony oxide ores are important antimony resources, but their recovery is still a problem. In this paper, the adsorption behaviour and mechanism of dodecamine and quaternary ammonium salt on the surface of cervantite and quartz were investigated. The flotation behaviour of cervantite and quartz using quaternary ammonium salts and dodecylamine as collectors was studied by single mineral flotation experiments. The adsorbed amount was measured and infrared spectroscopy was used to study the ability of several cationic collectors to float cervantite and quartz. The results show that quaternary ammonium salts can simultaneously float the cervantite and quartz. It is difficult to achieve separation of the two minerals using quaternary ammonium salts as collectors. At pH>10, dodecylamine can float quartz but not cervantite, which can achieve reverse flotation separation of the two minerals. The difference between the abilities of quaternary ammonium salts and dodecylamine to float cervantite and quartz lies in the different ionisation properties of the two reagents. Quaternary ammonium salt is a strong electrolyte that is completely ionised in the pulp and exists mainly in the form of quaternary ammonium ions. Dodecylamine is a weak electrolyte and predominantly forms molecules under alkaline conditions. Keywords: Cervantite, quartz, dodecylamine, quaternary ammonium salts, flotation

Jan 1, 2020

By Dilermando Nagle Travessa

High strength-light weight materials are very attractive for the transportation sector, particularly to the aerospace industry. High strength-age hardenable aluminium alloys are widely used in airframes due to their unique combination of strength, density, toughness, corrosion resistance, cost and easy processing. However, the hardening capacity of such alloys is somehow saturated due to thermodynamic issues related to the conventional processing. The production of aluminum-matrix composites is a promising strategy to overcome this limitation, resulting in strength levels that cannot be reached by actual commercial aluminum alloys. In the present work, multiwall carbon nanotubes were used to reinforce the AA6061 aluminium alloy. 1 and 2% weight percent of MWCNT were mixed to the alloy powder by high-energy ball-milling process. The blended powder was consolidated by hot extrusion. The obtained composite bars were submitted to heat treatment for the T6 condition in order to combine both CNT dispersion and precipitation hardening effects. Optical and scanning electron microscopy, as well as hardeness testing, was used to characterize the bars. Typical wrought microstructure, free of defects, was observed on the extruded bars. Hardness of the composites was observed to increase by 20, 28 and 68% for 1% MWCNT 6 h milling, 2% MWCNT 6 h milling and 2% MWCNT 10 h milling, respectively, in the as-extruded condition. The better performance for the composites blended at higher milling time was attributed to a better nanotubes dispersion. Subsequent heat treatment to the T6 condition did not result in additional hardening.

Aug 8, 2018

By E. R. Bauer

The trend in underground room-and-pillar coal mining is to employ remote-control continuous mining machines and extended cuts, 12 m (40 ft) deep or more. This system of coal extraction, adopted by over 435 mines, can create additional worker-safety hazards. To address the ground control and worker-positioning hazards, a combination of statistical analyses and numerical modeling was conducted. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the Coal Mine Roof Rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling to predict roof displacements during extended-cut mining was completed. The paper describes the results of these studies and their impact on the safety of extended-cut mining.

Jan 1, 1999

By S. Chatterjee

Mining represents the first industry in the United States to have federally mandated training for its workers. Although the topics to be covered are specified in 30 CFR 48, course content is left to the discretion of the individual mine operators. Unfortunately, certain topics to be covered, such as prevention of accidents, are usually mine specific, making it very difficult to use the same course content in every mine. Further, training requirements may change from one mine to another, due to changes in the demographic characteristics of the workers, or changes in job and organizational characteristics. Therefore, if the intention of safety training is to modify the behavior of workers, it is expected that there should be some changes in the content of safety training programs in order to address the specific requirements of individual mines, or at least mines of similar worker and job characteristics. This study has been directed towards the development of a systems-based procedure for conducting a needs analysis. A special effort was made to understand the psychology of worker behavior by analyzing worker reactions to various organizational and job characteristics.

Jan 1, 1994

By Harrison AT, Smart RM

Backfill systems using unconventional cementitious hinders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: 1. A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings 'stable' slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 in high and the tailings were relatively high in pyrite. .\ GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shnnkage). The system used a slurry, but the addition of the ;iutivator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: ò sloping widths (mining heights) above 1.6 in; and ò shaft pillar removals in seismically active areas at the end of the life of the shafts. \This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems).

Jan 1, 1998

By R. Craig McClung

Contrary to other sulfide minerals, where recovery is principally liberation controlled, the recovery of molybdenite is more complex. It is this complexity that initiated a geometallurgical investigation of molybdenites from Bingham Canyon. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes have on recovery. All samples were analyzed using normal mineralogical techniques. The results reveal the presence of two distinctly different types of molybdenite. These have been identified as the two polytypes of molybdenite: i.e. hexagonal (2H); and rhombohedral (3R). The 2H-polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the current pit bottom. The 3R-polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance and are concentrated along the margins of the current pit. Concerning their metallurgical behavior, each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. The 2H-polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This results in the production of a high quality concentrate under normal operating conditions. The 3R-polytype, by comparison, is difficult to grind and kinetically “slower” floating with surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R-polytype, modifications to the normal operating parameters may be necessary to improve recovery. This investigation highlights the necessity for understanding the mineralogical characteristics of any economic mineral(s), as these will have a direct impact on recovery.

By N Esmaeili, M Saghaeian, L Hosseini, V Sheikhzadeh, R Hejazi

Ore roasting has long been used for beneficiation and assay upgrading of different ores. In this process, which is mainly used for sulfide ores, the ore is heated to a high temperature. More specifically, it is a metallurgical process involving gas-solid reactions at elevated temperatures. Some types of Iron ore are weak in magnetic properties. Hematite, goethite and limonite are classified in this group. Unlike magnetite, which shows strong magnetic susceptibility, these ores are hard to beneficiate through magnetic separation route. Many researches have focused on gravity separation and flotation routes for upgrading these ores and these methods have also been utilised in the industry. One of the methods to whose industrial application less attention has been paid is magnetising roasting in which the non-magnetic iron ore is transformed to magnetite which is further beneficiated through magnetic separation. In this study, magnetising roasting tests have been performed on one goethite sample in order to check the feasibility of using this method for this specific ore in industrial scale. It is worth mentioning that high intensity magnetic separation have been performed on this sample before but the achieved results were not promising. Results have revealed that through magnetising roasting magnetite content of the ore could be increased from 1.7 per cent up to about 25 per cent. FeO content of the feed sample was increased from 1.03 per cent up to around 9.25 per cent. Also optimum size distribution for achieving the best results in magnetising roasting for this sample has been determined through this study. The best results were achieved when the ore size was 0–10 mm. The effect of coal ratio, time and temperature on the process have also be studied. A coal ratio of 5 per cent, time of 30 min and a temperature of 850°C were determined to be the optimum conditions. Finally, the technical feasibility of utilising magnetising roasting for this specific ore has been confirmed.

Aug 24, 2022

By T Suwa, S Ishida, J Xue, S Fuchida, H Shimada, Y Aoki, C Tokoro

Pyrite depression with prolonged pre-conditioning treatment in high salinity water has attracted much of researchers’ interest in recent years considering the increased utilisation of multiple stage flotation, closed water circuits, clay minerals, and sea water in flotation plants. In this study, the role of calcium (Ca)/magnesium (Mg) precipitates in stabilising the dissociative ferric hydroxy-xanthate (FHX), and its effect on modifying the balance of hydrophobic/hydrophilic species on the pyrite surface were primarily investigated. The total amount of extractable Fe-bearing species on pyrite concentrates and tailings after floatability test was quantitively determined using ethylenediaminetetraacetic acid (EDTA) extraction tests combined with inductively coupled plasma optical emission spectroscopy (ICP-OES). A more evident accumulation of extracted-Fe in pyrite concentrates rather than it in pyrite tailings was observed at both pH 9 and 10.5 when pyrite was pre-conditioned in Ca/Mg-bearing solutions for 360 min. Fourier transform infrared (FTIR) spectroscopy showed the main xanthate derivatives changed from di-xanthogen (1155 cm-1 ) to FHX (1167 cm-1 ) on the oxidised pyrite samples that were preconditioned in Ca/Mg-bearing solutions. Scanning electron microscopy-energy dispersive spectrometry (SEM-EDS) suggested the preferential accumulation of FHX upon secondary Ca/Mg-bearing precipitates as reflected by the higher Fe/S ratio together with the decrease of O element herein after xanthate conditioning. Although the hydrophilic secondary Ca/Mg/Fe-bearing minerals on the pyrite surface generally deteriorate pyrite’s floatability, the upper section of these secondary hydrophilic aggregates is partially covered by FHX alongside with further multilayer-adsorbed di-xanthogen. The precipitated Ca/Mg-bearing precipitates promotes the immobilisation of dissociated FHX derived from the reaction among iron oxyhydroxides and xanthate anions upon the localised secondary Ca/Mg/Fe-bearing minerals via acid–base complexation. Therefore, this phenomenon alleviates the hydrophilic modification of secondary Ca/Mg/Fe-bearing minerals to pyrite considering the immobilised FHX upon localised precipitates shows a slight hydrophobicity, and meanwhile, the upper FHX benefits the multilayer adsorption of di-xanthogen via the interaction among their inner hydrophobic alkyl chains.

Aug 24, 2022

By S Whitton, W Wimmler, L Wimmler

“Given the increasing scrutiny of the mining industry and its relatively poor record with regards to mine tailings management, increased requirements to minimise water usage (often accompanied by very high costs of water) and the need to demonstrate achievable long-term closure strategies, it is likely that the option of a filtered tailings system will need to be considered in many operations in future.” (Australian Centre for Geomechanics, 2018). Given such a statement as a conference introduction, it is only appropriate that a range of potential technologies are investigated and compared, to create awareness for even underrated but appropriate technologies. The advantages and disadvantages of all technologies need to be considered and analysed. Suppliers are swift to promote their technologies advantages; however aspects of sustainability are not always fully understood. Perhaps a combination of two filtration technologies is appropriate. This paper delves into the technical details, good or bad, of four mechanical dewatering technologies in tailings dewatering and provides insight on an undervalued and, in the author’s opinion, young technology – the screw press.

Jul 1, 2021

By John Newby, Edward Kennedy, Ulf Gwildis

Alluvial deposits of major rivers often provide relatively uniform tunneling conditions. However, these conditions pose specific challenges due to the tunneling behavior of the granular soils as flowing ground, if unsupported. This paper describes the design considerations and construction experiences gained during the Tunnel Boring Machine (TBM) drives for the Annacis Island WWTP New Outfall System in the Vancouver, B.C. metropolitan area. Meeting the design criteria for connecting two (2) deep on-land shafts with an in-river riser manifold required advancing a 5-meter-diameter slurry TBM through the Fraser Rivers sands and at a tunnel invert elevation with a baseline hydrostatic head of 3.4 bar.

Dec 1, 2022

By J. V. Wood, P. Davies, J. L. F. Kellie

A new range of wear-resistant materials is being produced by technology that has been used to develop high performance metal-matrix composites. These include steels and aluminium alloys that can be made as sheet, plate, rod or bar. The incorporation of hard, wear-resistant particles in an alloy matrix is achieved by reactive casting, spray deposition and powder metallurgical techniques. For example, large particles of TiC can be homogeneously distributed in steel during casting and the subsequent product can easily be rolled to plate. Similarly, up to 20% alumina particles and SiC can be injected, respectively, into steel and wear-resistant aluminium alloys by spray deposition. The current state of development of the process is reviewed and indications are given of the projected applications of such materials.

Jan 12, 1992

By Philip W. Johnson, Charles D. Haynes

"Abstract - The coalbed methane industry has become a prominent source of domestic natural gas, with its technology having evolved over the past 30 years. Whereas most coalbed methane wells are able to produce without major interruption over their economic lives, wells operating in an underground mining area are subject to being mined-through. If mine-through occurs, the productivity of the well is at least compromised, and may even be terminated. The economic consequences of mine-through may be relatively simple if mineral ownership and extraction rights are common for the coal and coalbed methane. However, if ownership is not common and a superior coalbed methane lease exists, the coalbed methane ownership must be compensated for lost production caused by mine-through. This paper presents a relatively straightforward method to calculate the value of the lost production caused by the mine-through. It uses technology from mining and petroleum engineering, as well as simple economics and financial management techniques.Sommaire - L’industrie de la production de méthane houiller est aujourd’hui une source importante de gaz naturel domestique dont la technologie a considérablement évolué au cours des trente dernières années. Bien que la plupart des puits de méthane houiller peuvent être mis en production durant l’entièreté de leur vie utile sans interruption majeure, les puits implantés en périphérie de mines souterraines sont sujets à être recoupés par ces dernières. Un tel recoupement peut compromettre, ou même mettre fin à la production d'un tel puits. Les conséquences économiques du recoupement par une mine souterraine peuvent être relativement simples quand les droits miniers et les droits d’extraction sont détenus en commun pour le charbon et le méthane houiller. Si toutefois ces droits ne sont pas détenus en commun et qu’il y a eu octroi d’une concession de méthane houiller de qualité supérieure, les détenteurs du méthane houiller doivent être compensés pour la perte de production résultant du recoupement par une mine souterraine. Cet article présente une méthode relativement simple pour calculer la valeur des pertes de production suite au recoupement par une mine souterraine. Cette méthode fait appel aux technologies de l’industrie minière et pétrolière ainsi qu’à des techniques simples d’économie et de gestion financière."

Jan 1, 2006

By Sumit Kumar Biswas, Moyukh De, Sibapriya Mukherjee

"The piles often are also subjected to lateral (horizontal) forces and moments. In fact, there are some structures where the primary function of piles is to transfer lateral loads to the ground. Proper analysis of laterally loaded piles is very important to the geotechnical and civil engineering profession.In the present investigation an experimental study has been carried out with free head short model cast iron hollow piles of outer diameter of 24 mm and L/d ratios of 8, 10, and 15. The experimental results have been supplemented by numerical techniques using PLAXIS-3D Foundation version 2.1 software. The results have been found to agree reasonably well with the experimental results. Further finite difference approach has been adoptedto reduce the computational time and to calculate the coefficient of modulus of subgrade reaction (?h) from the load- deflection data obtained from PLAXIS output at different pile depths. The parametric study has been extended for the non-dimensional form defined as flexibility ratio (F.R.),where ?h, L, Ep and Ip are the coefficient of modulus of sub-grade reaction, the embeddedlength of model pile, elastic modulus of pile material and the moment of inertia of model pile about the central axis respectively).The variation of coefficient of horizontal modulus of sub-grade reaction (?h) has been studied with respect to the following parameters for homogeneous soil system: relative density andL/d ratio. It has been found that the logarithm of flexibility ratio increases with increase inrelative density and increase inL/d Ratio. The values of ?h obtained by the proposed method have been, found to be close to the numerical results.As output of this research, graphs have been generated in respect of different parametric variations to gain an insight into behavior of piles under lateral load for short piles."

Jan 1, 2015

By Dudley L. Davis, E. C. Peterson

INTRODUCTION THE Darwin District is 30 miles east of Olancha which is 220 miles north from Los Angeles via U. S. Highway No. 6. The ore deposits occur in the Darwin hills that have been elevated above the Darwin Plateau by typical basin and range-type faults. Some of these faults have been active quite recently as shown by the displacement of Quaternary (?) basalt flows and the rejuvenation of erosion in Darwin wash. The ore bodies occur as fissure fillings and replacement of favorable beddings in a thick series of Paleozoic limestones, dolomites, shales and quartzites. Rich oxidized lead-silver ores were discovered in the early seventies. By 1875, Darwin had a population of about 5000, and by 1880 several small mills and smelters had been built. Early exhaustion of surface ores, the isolated location of the district, and fluctuation of metal prices caused intermittent operations until World War II. The district production is estimated at about $3,000,000 prior to 1900 and perhaps $4,000,000 between 1900 and 1945 when Anaconda purchased the major producing mines. For the past two years, daily production has averaged 75 tons of direct shipping and 150 tons of milling-grade ore. At present, 300 tons of mixed oxide and sulphide ore are treated by flotation, the oxidized lead minerals being activated by addition of sodium sulphide after galena and sphalerite have been recovered from the circuit. Extraction averages 85 pct of the lead, 80 pct of the silver, and about 33 pct of the zinc in a bulk concentrate. The mill is designed so that minor changes permit selective flotation of pyritic lead-zinc ores encountered at depth. GENERAL GEOLOGY The oldest rocks in the Darwin hills are a series of Paleozoic limestones, dolomites, shales and quartzites probably Pennsylvanian in age. These rocks have been intruded on the west by the Coso granite batholith and on the east by a granodiorite stock. Numerous sills and dikes grading from orthoclase granite to gabbro are exposed in the underground workings. The sedimentary rocks have been considerably folded and faulted, the most prominent structure being a northwest pitching anticlinal fold, the crest of which lies just west of the ridge line of the Darwin hills. The east limb of this fold has been intruded by the granodiorite stock and east of the stock the sediments show several closely spaced anticlines and synclines. The minor flexures on the west flank of the major fold are structurally important in localizing the ore in the Defiance and Essex mines of the Darwin group. There are three principal systems of faulting and fissuring, most of which are post-intrusive and premineral in age, with minor amounts of postmineral movement. The Darwin tear fault is the largest, most persistent fault in the district. It strikes N 60 to 95°W, dips steeply south and is traceable for about 1o miles. It is a normal

Jan 1, 1947

By L. F. Pett

ALTHOUGH Kennecott's orebody has long been outlined, it is still necessary to define further its limits. This mine, long an advocate of churn drill methods, recently supplemented its practice by using a diamond drill. So far, the diamond drill holes have been along the main canyon floor which traverses the mine area. This zone, highly fractured, is cut by numerous friable quartz veinlets encountered within the porphyry. These veinlets, formed by filling contracted porphyry fractures with hot, siliceous, mineral-bearing solutions, are often more highly mineralized than adjacent porphyry. They pulverize on contact, yielding only slight amounts of core.

Jan 7, 1951

By Dudley L. Davis, E. C. Peterson

Introduction The Darwin District is 30 miles east of Olancha which is 220 miles north from Los z4ngeles via U. S. Highway No. 6. The ore deposits occur in the Darwin hills that have been elevated above the Darwin plateau by typical basin and range-type faults. Some of these faults have been active quite recently as shown by the displacemerit of Quaternary (?) basalt flows and the rejuvenation of erosion in Darwin wash. The ore bodies occur as fissure fillings and replacement of favorable beddings in a thick series of Paleozoic limestones, dolomites, shales and quartzites. Rich oxidized lead-silver ores were dis'Overed in the early seventies. BY 1875, Darwin had a population Of about 5000, and by 1880 several small mills and smelters had been built. Early exhaustion of surface ores, the isolated location of the district, and fluctuation Of metal prices caused intermittent operations until World War 11. The district production is estimated at about $3,000,000 prior to 1900 and perhaps $4,000,000 between 1900 and 1945 when Anaconda purchased the major producing mines. 'or the Past two Years, daily production has averaged 75 tons of direct shipping and 150 tons of milling-grade ore. At present, 300 tons of mixed oxide and sulphide ore are treated by flotation, the oxidized lead minerals being activated by addition of sodium sulphide after galena and sphalerite have been recovered from the circuit. Extraction averages 85 pct of the lead, 80 pct of the silver, and about 33 Pct Of the zinc in a bulk concentrate. The mill is designed so that minor changes permit selective flotation of pyritic lead-zinc ores encountered at depth. General Geology The oldest rocks in the Darwin hills are a series of Paleozoic limestones, dolomites, shales and quartzites probably pennsyl-vanian in age. These rocks have been intruded on the Rest by the Coso granite batholith and on the east by a granodiorite stock. Numerous sills and dikes grading from orthoclase granite to gabbro are exposed in the underground workings. The sedimentary rocks have been considerably folded and faulted, the most prominent structure being a northwest pitching anticlinal fold, the crest of which lies just west of the ridge line of the Darwin hills, The east limb of this fold has been intruded by the granodiorite stock and east of the stock the sediments show several closely spaced anticlines and synclines. The minor flexures on the west flank of the major fold are structurally important in localizing the ore in the Defiance and Essex mines of the Darwin group. There are three principal systems of faulting and fissuring, most of which are post-intrusive and premineral in age, with minor amounts of postmineral movement. The Darwin tear fault is the largest, most persistent fault in the district. It strikes N 60 to 75°W, dips steeply south and is traceable for about 10 miles. It is a normal

Jan 1, 1949

By F. L. Bosqui, A. D. Wilkinson

EVEN though the world has not been crying for more copper for the last three or four years there has been some important mill and smelter construction. Discovery and development of large new high-grade copper deposits in Africa has led to the construction of extensive reduction facilities there, prominent among which is the concentrator and smelter of the Rhokana Corporation at N'Kana. Northern Rhodesia. The 3000-ton concentrator adjoins the central shaft. A little over half a mile to the southeast, at an altitude of 40,010 ft., is the smelter, designed on the site by 1. H. Wynne. It is arranged primarily to treat N'Kana copper concentrates, but can also handle concentrates and direct-smelting ore from outside sources. Excavations were started late in 1930; concrete was first poured on Jan. 6. 1931; and the first blister cop¬per was cast on March 1.9, 1932, less than fifteen months later. During this period, which included several months of heavy tropical rains, some 10,000 cu. yd. of concrete was poured and 41000 tons of structural steel erected under the supervision of construction engineer, A. Ek, with a labor force of 60 to 30 Europeans and about 300 natives. The steelwork was fabricated by Head Wrightson & Co. in England, and the boiler plant equipment furnished and erected by the International Combustion Co. Ltd.

Jan 1, 1934

By A. McLean, W. Q. Chen, W. Yan, M. Barati, Y. D. Yang

In order to maximally remove the harmful impurities phosphorus and reduce the loss of valuable elements from Si-based alloy for production of solar-grade silicon, thermodynamic properties of the Si-based alloy were studied. In this work a new model, the Molecular Interaction Volume Model (MIVM) derived from statistical thermodynamics, was successfully used in the Si-based and Si-Fe-based alloy. The calculation started from binary Si-Fe, Si-P and Fe-P systems, then the thermodynamic parameters of ternary systems could be derived based sub-binary systems. Using the activity coefficients of the elements in the Si-based alloys and the saturated vapor pressure of the pure substance of the components, mass fraction of P during vapor-liquid equilibrium can be calculated. The calculated thermodynamic parameters were compared with experimental data available in different publications, and it is found that the thermodynamic parameters calculated using MIVM model are in good agreement with the measured results. The calculated result shows that the mass fraction of phosphorus during vapor-liquid equilibrium of Si-Fe-P melt increases with the increasing phosphorus content and decreasing temperature. This is an important direction for experimental practice in vacuum or low-pressure EML refining of ferrosilicon for potential production of solar-grade silicon without significant vaporization loss of valuable element.

Jan 1, 2015