Search Documents

By Jeffrey C. Evans, Daniel G. Ruffing, Hejintao Huang

Soil-bentonite slurry trench cutoff walls are the most common type of vertical cutoff wall used in the US for seepage control and for passive control of contaminant migration at environmental sites. Design considerations are often limited to constructability considerations and a target hydraulic conductivity. With design-build contracts common, the backfill design is often left to the contractor. As a barrier soil, the hydraulic conductivity of bentonite slurry wall backfill is typically required to be equal to or below 1x10-7cm/s. The importance of stress state upon the hydraulic conductivity as well as the expected stresses are both established in the literature. Grain size distribution of the base soil and bentonite content both affect compressibility and hydraulic conductivity. This paper describes the results of studies undertaken to evaluate the interrelationships between compressibility, hydraulic conductivity, grain size distribution, and bentonite content. Three base soils were used representing a range of soils found on typical construction projects. Using these base soils, mixtures containing a range of dry bentonite contents from 0% to 5% were prepared to a slump consistent with field practice. The compressibility and hydraulic conductivity were measured in consolidometers adapted for falling head permeability tests at the end of each load increment. These experiments yielded the relationship between effective stress and hydraulic conductivity as well as consolidation characteristics including time rate of consolidation and coefficients of compressibility. The experimental results are then used to indirectly evaluate stress development and to assess the time needed for consolidation. The findings show a substantial decrease in hydraulic conductivity as effective stress increases, regardless of base soil type and dry bentonite content, a relative insensitivity of stress development to backfill compressibility, and a wide range of values for coefficient of consolidation depending upon backfill mixture and stress level.

Jan 1, 2016

By Tapio Ahokainen, Asmo Vartiainen

"Outotec's portfolio contains a wide variety of smelting solutions for non-ferrous metals. Some of these include flash smelting for primary copper and nickel, flash converting for copper, Ausmelt technology for primary and secondary copper, nickel, tin, lead, and zinc residues and waste, Kaldo technology for secondary copper, lead, and precious metals recovery. Outotec also offers slag cleaning technologies and much more.Company provides complete process solutions tailored to each customer's individual needs. Decades of experience have resulted in extensive metallurgical know-how that ensures the most profitable process choice and optimal performance. Outotec's life cycle technology partnership with their customers spans from the early stages of process solution design through the supply and commissioning of the entire process chain. They include integrated process control and holistic service and support concepts. Continuous research and development ensures that the customer is provided with the latest advancements in process and equipment solutions.IntroductionOutotec develops and provides technology solutions for the sustainable use of the Earth's natural resources. Solutions are ranging from various processes and special equipment needed for metallurgical extraction and mineral processing of ores to the production of refined metals and minerals. The processes include not only the grinding and physical separation of ores but also the smelting and leaching of base metals and precious metals. The company provides engineering services for whole projects as well as life cycle services on the equipment and products that they supply."

Jan 1, 2012

By N. D. Schupp

The Doe Run Company's Herculaneum, Missouri lead smelter has existed in continuous operation since 1892. Throughout the history of the plant extensive developments have been made to improve throughput, increase productivity, decrease operational costs and improve technology, while remaining an environmentally responsible producer of high quality primary lead in the international market. This paper provides an overview of the Herculaneum smelter, focusing on the most recent configuration of the operations. The paper includes discussion on all the aspects of primary lead production at the Herculaneum smelter.

Jan 1, 2000

By D. S. Bird

The Kennecott Utah Copper Modernization Project, initiated in 1986, was directed to provide an expansion and modernization of mining and process facilities at the property's Bingham Canyon Mine and ore concentrators. Major components in the project included installation of an in-pit ore crusher, transfer conveying system, and construction of a new copper ore concentrator with a design capacity basis of 70,000 tonnes/day. The Copperton Concentrator was commissioned in February 1988. A principal feature of the plant is the grinding circuit, comprised of three identical lines, each consisting of a 10.37 m (diameter) by 4.57 m (length) Semi-Autogenous Grinding (SAG) mill and two 5.54 m (diameter) by 8.62 m (length) ball mills. The SAG mills are driven by two variable-speed 9,000 kW DC motors coupled through a clutch-pinion gear-ring gear assembly. The ball mills are driven by 4,125 kW synchronous motors coupled through a typical clutch-pinion gear-ring gear system. The expansion and particularly the Copperton Concentrator performance was so successful that by early 1989, management began examining options to further expand production capacity. With regards to the concentrator, numerous alternatives were considered, ranging from installation of a grinding line similar to one of the existing lines, to a "super" line consisting of a 12.8 meter (diameter) SAG mill and a 20,000 kW motor with a capacity of 50,000 tonnes per day. The technical and economic analysis of the various scenarios indicated that one "large" 11.0 meter (diameter) by 4.88 meter (length) SAG mill with a production capacity of 32,000 tonnes per day and a 12,000 kW drive would be optimum. The key question to be answered in the project was whether to continue with the pinion-ring gear combination, or install a gearless drive. The following paper outlines many of the items that were evaluated in the mill selection process followed by actual plant performance, and a discussion of ongoing plant continuous improvement projects.

Jan 1, 1995

Edward A. UehlinG, New York City (communication to the Secretary*):—Mr. Baker's paper is one that brings up a subject of great importance, and if full statistics could be collectecl of the number of furnace-linings ruined by reason of bad distribution by skip-hoists, it would be found an astonishing array. Unfortunately a universal remedy has not yet been found. The fact that Mr. Baker has apparently succeeded in overcoming the trouble at Sydney, is no guarantee that the same remedy applied at another plant, where very different or even slightly different conditions prevail, mould cure the trouble. That it requires but a slight continuous difference of penetrability in the column of the descending stock of one section, over another, to produce channeling, is clearly demonstrated by Mr. Baker's experiments, by which he reversed the channeling from front to rear instead of remedying the trouble. Every change in the physical make-up of the charge necessarily requires a specific adjustment; even supposing this feasible, the regular working of the furnace is by no means assured, because with the high pressures now customary, the tendency of the ascending gases to plow their way through in a direct course, prevails, and having once opened up a passage, they will persist and cause trouble. Homogeneous filling-, hard driving and regularity of working are incompatible. The higher the furnace, the greater the

Jan 1, 1905

By O. Craciun, C. A. Bridges, M. Cai, J. Sugawara

There are a number of methods that can be adopted for predicting the ultimate lateral resistance of a free-head rigid pile, from the conventional Brinch Hansen and Broms solutions to three-dimensional finite element analyses. Often these methods give rise to significantly different pile ultimate lateral capacities which could lead to either unsafe or too conservative designs. It is also well known that finding a rigorous and practical solution is challenging due to the complex three dimensional and nonlinear soil-structure interaction. This paper reviews some of the most common methods and produces results of pile ultimate lateral capacities embedded in cohesive or cohesionless soils. Subsequently, a finite element analysis is performed using PLAXIS 3D modelling under the same design conditions. Based on comparison of results, limitations and advantages are highlighted, and the most suitable method is proposed from a practical point of view.

Nov 1, 2022

By Sowmiyaa. V. S., Tiruvengala Padma

Axial compression capacities of bored cast in situ piles as per Indian and International Standards are compared in this paper. Bored cast in-situ piles resting on soil and rock are considered for capacity assessment comparison. The standards considered for comparison are Indian Standards namely IS 2911-Part 1-Sec 2:2010 and IRC 78, International Standards like AASHTO LRFD Design-2017, API 2A WSD, BS 8004:2015 & EN 1997: Part 1:2014. The end bearing mobilization limits as proposed by various standards and their influence on longer piles in cohesive and cohesionless soils are discussed.

Sep 1, 2022

By García B., Wolff E.

The pellet qualities primarily depend upon the thermal profile and gaseous environment during induration. During the induration of the pellet, it undergoes physical as well as chemical changes. Physical changes are mostly due to sintering and chemical changes are due to carbon burning inside the pellet. The effect of carbon on sintering is investigated on a single pellet scale using an optical dilatometer. Sintering is a complex process that involves transportation through various mechanisms. Sintering is quantified in terms of sintering ratio and the kinetic parameter, exponent ‘n’, under isothermal conditions is deduced using the power law equation. The value of n can be used to estimate the sintering mechanism at different isothermal temperatures. Also, the activation energy is calculated using the empirical Arrhenius equation. The activation energy of 0 per cent coke and 1 per cent coke-containing pellets are 531.0 kJ/mole and 552.6 kJ/mole respectively. The order of magnitude of activation energy suggests the same mechanism in both cases. Although the mechanism of sintering is the same, 1 per cent coke-containing pellet sinters more at any isothermal temperature.

Jun 17, 2024

By Juan Hernández Ávila

This work studies the Molybdenum effect on the microestructure, mechanical properties of an as-cast ductile iron. For this study five ductile irons with different amounts of Molybdenum each were made in an induction furnace. In this material nodule count and nodularity is affected by the Molybdenum additions; The iron´s matrix, nodules and the phase were analyzed using scanning electron microscopy detecting Molybdenum only in the matrix. Mechanical properties such as hardness, microhardness, tensile strength and yield strength show increments as the Molybdenum amount is increased. In the same way, ferrite and pearlite phases display a variation in their percentage as the contents of the alloy element increase. This element has a marked influence on the pearlite interlaminar spacing. From the obtained results we conclude that Molybdenum in these quantities dissolves in solid ferrite solution during the solidification process, improving the material´s mechanical properties.

Jan 1, 2009

By M. P. Youker

USE OF LOW-PRESSURE GAS BURNERS IN OIL- FIELD BOILERS

Feb 1, 1922

By R. J. SHAW

Oil shale has been defined as, "a compact, laminated rock of sedimentary origin yielding over 35 percent of ash and containing organic matter that yields oil when distilled but not appreciably when extracted with the ordinary solvents for petroleum." The oil-yielding organic matter in oil shale, commonly called kerogen, decomposes upon application of heat to form bituminous materials that are soluble in organic solvents and may be extracted from the inorganic residue. However, separation usually is accomplished by continuing the heating and thereby cracking the primary bitumens to gas and oil, which distill, leaving a carbonaceous material on the mineral residue. It has been suggested that this conversion takes place only at relatively high temperatures - 750°F or higher. On the other hand, other workers have found that transformation may take place to some extent at temperatures as low as 400°F. In either a solvent extraction or a destructive distillation process for separating organic material from the inorganic portion of oil shale, the quantity of heat required to raise the temperature of the oil shale sufficiently to induce a satisfactory rate of conversion of kerogen to oil is important in determining the design of an economical process. Likewise, the quantity of heat recoverable from a spent shale is important in determining the overall heat balance of the process. Published data on the specific heat of American oil shales are meager. Gavin and Sharp present data for two samples of Colorado oil shale, one from near DeBeque and one from Parachute Creek, and for a sample of spent shale over a temperature range of 68°F to 1940°F. McKee and Lydor present data on the specific heat of two samples of oil shale from near DeBeque, Colorado. Additional thermal data on various grades of oil shale over a wider range of temperature are needed in order to apply sound engineering practices to the design of equipment for processing oil shale.

Nov 1, 1947

By N. Naudé, J. de Villiers, C. P. Bergmann

It is proposed that the physical and chemical composition of individual mineral particles are an appropriate basis from which to model the performance of minerals processing equipment. Such a particle-based approach enables modelling across disciplines such as comminution, classification and flotation and automatically generates the traditional mass and chemistry balances. The general approach followed is to generate full grade-recovery curves for a separator by sampling product and tailings at varying mass yields. AutoSEM characterisation of each sample provides particle data that is used to reconcile mineral deportment and liberation to the measured size and assay data. In this way, partition surfaces can be generated and modelled. In this paper, an empirical model for the performance of a gravity spiral concentrator treating fine chromite ore is proposed. The model is based on the combination of two partition surfaces and is able to accommodate both forward and reverse gravity concentration effects per size fraction. The results show that this approach is well suited to represent spiral performance for the cases evaluated. The effect of two feed particle size distributions on the performance of the Multotec SC21 and SC25 spirals is demonstrated. Simulations are run in an Excel environment, linked to Python-enabled routines for enhanced data management and calculation speed. Keywords: Spiral concentrator, gravity separation, particle-based modelling

Jan 1, 2020

By V. Jokovic

Hydrocyclones are the most commonly used classifiers in the mining industry. The reason for this is their low operating cost and a small footprint. Data from plant trials where screens replaced hydrocyclones indicated that lower bypass of fines and sharper separation could improve breakage rates, with a positive effect on flotation circuit performance throughput. Despite the importance of classification, hydrocyclones have not received as much attention as more expensive comminution units, and their technological progress has been incremental. Noticeable water split (Rf) reductions of a semi-inverted hydrocyclone have been reported in the past. According to theory, the hydrocyclone with reduced Rf will improve classification of fines. A classification study using semi-inverted hydrocyclones was conducted to determine if a hydrocyclone could be operated in a way that would minimise misclassified fines. The classification performance of a semi-inverted hydrocyclone will be presented in this paper and other potential applications will be discussed. Keywords: Semi-inverted hydrocyclone, water split, misclassification of fines

Jan 1, 2020

By J. Petersen, H. Naderi, M. H. Nikzad, M. Karimi

In this research, the thermodynamic study of sodium persulfate (Na2S2O8) solution in the presence and absence of H2SO4 and Fe3(SO4)3 was done. Eh-pH and equilibrium distribution diagrams were constructed using Outotec HSC Chemistry Software and the main stable ionic species were determined. Also, the mean activity coefficient and Pitzer model coefficients were evaluated. Effects of system composition, sodium persulfate concentration and temperature were investigated. According to the results, HS2O7 -, HS2O8 -, S5O3 2-, S4O3 2-, S3O3 2-, HS- and NaSO4 - are the main stable species in these three systems. Increasing of sodium persulfate concentration resulted in disappearing of SO4 2- and the appearance of NaSO4 -. The main effect of increasing the temperature from 25 to 75oC, is changing the stability regions of HS2O7 -, NaSO4 -, SO4 2- and S2-. From equilibrium studies, it was concluded that at 25 and 50oC, increasing the persulfate concentration results in a 55-60% decrease for HS2O7 - and an 20- 30% increase for HS2O8 -. At 75oC, HS2O8 - becomes the main species and its percentage decreases with increasing the persulfate concentration. Keywords: Thermodynamic, sodium persulfate, activity coefficient

Jan 1, 2020

By V. Sheikhzadeh, M. Saghaeian, N. Esmaeili, R. Hejazi, A. Dehghani Ahmadabadi

High Pressure Grinding Rolls (HPGR) are mostly used prior to pelletising processes to increase the specific surface area (SSA) of iron ore concentrate. For expressing SSA, the Blaine index is utilised as one of the most important dimensional properties of iron ore pellet feed. ISO 21283 is a standard test method that explains the manual of Blaine air-permeability apparatus for determination of this parameter. In this standard, the disaggregation method is based on passing the minus of 1 mm samples from the 0.150 mm sieve. The disaggregation process has an effective role on the results of Blaine airpermeability test especially for regrinding HPGR products. In this research, firstly the Blaine index of samples was measured without disaggregation. Following this, disaggregation was done by passing the minus of 1 mm samples through three sieves with different dimensions, 0.150, 0.090 and 0.045 mm, separately, and the Blaine index was calculated for each one. Finally, lab-mill with rubber balls, called Jar mill, was investigated as another option. Screen analysis and image analysis with SEM were performed to evaluate the effects of the sample's disaggregation on the size distribution and agglomeration of samples. The results showed that the disaggregation method with sieve size 0.150 mm, according to ISO 21283, was not applicable for HPGR products because the particles were still stuck together. In addition, the disaggregation method with the sieve size 0.045 mm or with Jar mill offered reasonable results. Keywords: Disaggregation, Blaine index, specific surface area, regrinding HPGR, ISO 21283, Jar mill

Jan 1, 2020

By A. Lebedev

Application of dynamic simulation for a base metal processing plant is discussed. The plant receives ore of variable quality from two pits and blending had to be applied to maximise recovery. The plant employs multiple stage crushing, screening, dense media separation, two-stage milling, flotation and further filtration. Stockpiles and bunkers are used in the plant to cater for breakdowns and operating delays, the latter being appropriately incorporated in the model. A detail dynamic simulation model was constructed from the rock face to the filtration plant to assist the plant design, notably with definition of the ore blending method, sizing storage capacity and in-plant conveyors. The plant model was broken down to capital equipment items and various feed types and mass balances were tested to ensure that the production target is met. The dynamic simulation tested the proposed blending method, identified bottlenecks, produced risk profiles for all strategic storage facilities and overall helped minimise the project risks and improve confidence in the plant design. Keywords: Dynamic simulation, ore grade, blending, capacity, risk profile, throughput, utilisation

Jan 1, 2020

By Recepoglu O, Tolun R, Yavasoglu N, Bulutcu AN

Scheelite was floated from a low-grade (0.28 per cent W03) calcitic (96.30 per cent CaCO3) scheelite ore using oleoyl sarcosine as collector and alkylated 8-hydroxyquinoline as modifier. Compared to oleoyl sarcosine alone, the grade and the recovery of scheelite concentrate were increased from 8.07 per cent to 33.54 per cent and from 55.1 per cent to 73.4 per cent, respectively. Infrared studies with pure calcite and scheelite minerals showed that while alkyl oxine is adsorbed on the scheelite surface, it is not adsorbed on the calcite.

Jan 1, 1993

By Yasuhiro Konishi, Norizoh Saitoh

"We have developed new recycling technologies, based upon an eco-friendly biotechnology, in order to extract precious and rare metals sourced from post-consumer products. Recently we have been focusing on the metal ion-reducing bacteria, Shewanella algae and Shewanella oneidensis, which are able to reduce and deposit the precious metal ions (gold (III), platinum (IV), palladium (II), and rhodium (Ill)) into metal nanoparticles at room temperature within 120 min. When targeting the leachates from printed circuit boards, the Shewanella bacteria were able to allow selective reduction and deposition of gold (III) ions under acidic conditions in the presence of heavy metal ions, proposing a new bio-recovery system for gold. We also found that the Shewanella bacteria can separate and concentrate soluble rare metal ions (dysprosium (III), indium (Ill), and gallium (Ill)) from dilute solutions. Using this biomass adsorbent, the effectiveness of system for the novel recovery of indium from the leachate of used LCD (liquid crystal display) panels has been demonstrated.IntroductionMany high-tech manufacturing industries are highly dependent upon the use of critical raw materials that are the rare metals (e.g. rare earth elements/indium) and precious metals (e.g. gold/platinum group metals). There are now serious global concerns over the short term and long term availability of critical raw materials for high-tech manufacturing. This highlights the paramount importance of sustainable component reuse and material recycling technologies for recovery of critical raw materials. We believe that the most important domestic source of precious metals is through more recycling, and this will require more research and further development for the recycling of precious and rare metals. In general, chemical/thermal recycling is deemed to be the most appropriate means to extract the precious and rare metals from postconsumer products. However, there are issues related to the heavy use of toxic and hazardous chemicals, and the release of toxic emissions.Biological recovery methods provide an attractive alternative strategy and use microorganisms to separate and concentrate soluble precious and rare metals from dilute solutions into microbial cells via biosorption [1-3] and biomineralization [ 4, 5]. Biological systems generally operate at ambient temperature and near-neutral pH. Consequently, microbial recovery of metals would be an environmentally friendly method for recycling precious and rare metals from end-of-use products."

Jan 1, 2014

By Késsius Bortolan Menezes

O complexo Minas-Rio da Anglo American iniciou suas operações em agosto de 2014. A usina de tratamento produziu, em 2016, cerca de 15,5 milhões de toneladas de concentrado. O minério, explorado em Conceição do Mato Dentro (MG), passa pelas etapas de cominuição, classificação, concentração e separação sólido-líquido antes de ser bombeado por 529 km até São João da Barra (RJ), onde é filtrado, estocado e embarcado para exportação. Durante a fase de projeto, a utilização de equipamentos pilotos com capacidade de centenas de quilos por hora foi de fundamental importância para verificação da viabilidade técnica do tratamento do minério. Contudo, a realização de um teste exigia um esforço muito grande, devido aos grandes volumes de minério necessários. Por isso, com o início das operações, os testes em escala de bancada começaram a ser mais explorados. Além deles, testes em mini planta piloto com capacidade de dezenas de quilos por hora são muito utilizados, pois permitem simular de forma simples diferentes circuitos. O trabalho tem por objetivo mostrar essa evolução histórica na utilização de ferramentas para avaliação do desempenho da flotação, com exemplos de resultados práticos obtidos, e como os mesmos influenciaram a tomada de ações que culminaram em melhorias industriais.

Oct 30, 2017

By Kallin de Souza

No âmbito da inspeção de segurança de caldeiras, a norma regulamentadora NR-13 estabelece a necessidade de um sistema de gerenciamento de integridade estrutural (SGI) com requisitos mínimos para atestar a segurança do equipamento. Entretanto, visando estabelecer um SGI que possibilite maior acompanhamento do equipamento e melhor direcionamento dos reparos instaurou-se um sistema de inspeção com procedimentos mais abrangentes. Esse trabalho apresenta as técnicas de ensaio não destrutivo (END) utilizadas usualmente na inspeção de segurança de NR-13 e novas como o ensaio IRIS (Internal Rotary Inspection System) [1]. As condições estruturais foram comparadas com as recomendadas segundo os códigos de projetos internacionais. Além disso, técnicas de estatística de engenharia de manutenção e projeto foram utilizadas, permitindo quantificar a segurança de operação e programar o momento da intervenção para o reparo.

Oct 30, 2017