Search Documents

By Wilson Blake

The occurrence of rock bursts in some deep mines throughout the world constitutes a severe operational hazard. In addition to endangering the safety of the miners, the rock-burst problem is a major factor in mining economically in deep mines because of the loss of production and expense owing to cleanup and repairs following a burst. Developing means of controlling or eliminating rock bursts has been the subject of intensive research for over 50 years. While much has been learned about the effects of rock bursts, little is known about their basic causes; hence, control measures have been at best only partially effective--attested to by the number and severity of bursts that continue to occur throughout the world each year. In the Coeur d'Alene mining district of north Idaho, the rock-burst problem continues as the silver and lead veins persist at depth. These veins are presently being mined at greater than 7,000 feet below the surface and will be mined to some 10,000 feet in the future. The majority of rock bursts in this district occur in pillars. While pillar bursting has been essentially eliminated in some deep-mining districts by longwall techniques, modification or application of this technique to the thin, irregular, and near vertically dipping veins of the Coeur d'Alene district has not been found to be practical. The creation of pillars is a consequence of the horizontal cut and fill mining method used. Figure 1 shows a vertical longitudinal projection of the silver vein at the Galena mine, illustrating the mining method. Stoping progresses between raises and is carried upward between levels. A horizontal pillar is created as a stope approaches a mined-out level. Recent broad-band micro seismic monitoring of rock-burst-prone stopes by the Bureau of Mines has shown that potential burst zones could be delineated weeks in advance of a burst and that a definite sequence of events took place prior to the occurrence of a pillar burst (1). Hence, time was available for control measures to be effected when a stope pillar reached a critical burst geometry.

Jan 1, 1971

By A R. Bonani, M P. Pe±a

The optimisation of slope angles, that is to say, increasing them, compared to the original design is always the subject of analysis of stability for geotechnical engineers and economic analysis for planning engineers. Questions to be answered include: What is the acceptable risk? What factor of safety? What probability of failure or reliability? The Rosario Open Pit has a history of failure, poor quality rocks and high pore pressures. It was decided to deepen the pit below the programmed design to test the practicality of different design approaches, which if successful, could be used to improve the economics of mining at Collahuasi. The revised slope design has factors of safety in the range of 1.0 to 1.2, probabilities of failure of ten to 38 per cent, and increased slope angles of between 3¦ and 5¦ with respect to the original design. The pit deepening with these design slopes will deliver an extra two million tonnes of ore which will have a significant positive impact on mining economics.

Jan 1, 2007

By Alex Luyima, Honglan Shi, Lifeng Zhang, Yongqing Jiang

"Leaching process has been suggested to recover most metals from waste PWBs. In this study, the leaching behavior of most metals present in waste PWBs is evaluated before and thermal treatment. Different leaching acids: hydrochloric acid (HCl), nitric acid (HNO3) and aqua regia are compared. The effects of acid concentration, particle size of sample, leaching time and temperature are examined. Results revealed that most metals are present in small particle size and sequential leaching of PWBs with a combination of HCl acid and aqua regia is capable of dissolving most of the metals content of PWBs. Leaching of thermally treated PWBs produced the highest leaching percentages for similar leaching conditions.IntroductionApproximately 20–50 million tonnes of electronic waste (e-waste) is produced globally per year. Waste Electrical and Electronic Equipment (WEEE) or E-waste is one of the fastest growing waste streams in the world. In developed countries, it equals 1% of total solid waste on an average [1]. The growing stockpile of used and obsolete consumer electronics has been called the “largest toxic waste problem of the 21st century [2]. Printed wiring boards (PWBs) is an essential part of almost all WEEE, and accounts approximately 3% of all WEEE by weight [3]. PWBs are a platform upon which microelectronic components are mounted. PWBs contain metals (~40 wt. %), ceramics (~30 wt. %) and plastics (~30 wt. %) [4]. The metallic part includes; Cu, Pb, Zn, Fe, Cd, Be, Cr, Au, Pt, Pd, Ag, etc. The plastic part of the PWBs is mostly epoxy resins. These plastic resins also contain very toxic halogenated flame retardants (HFRs) [5]."

Jan 1, 2012

By Zhigan Deng

Cooling crystallization was used to separate iron (III) and nickel (II) from acidic sulfate solution produced by leaching of molybdenum-nickel black shale. The effect of K2SO4 concentration, crystallization temperature, solution pH and crystallization time on recovery of nickel (II) and precipitation of iron (III) was investigated, in order to obtain effective separation of nickel and iron. The optimum parameters determined were as follows: 200 g/L K2SO4, 10 °C crystallization temperature, solution pH of 0.5 and 24 h crystallization. Under these conditions, 97.6% nickel (II) was recovered as K2Ni(SO4)2, 6H2O crystals and only 2.0% of the total iron (III) was precipitated. Recrystallization yielded K2Ni(SO4)2, 6H2O crystals with a purity of 98.4%.

By S. H. Chauvenet

HARRISBURG is situated on the Pennsylvania Railroad, one hundred and five miles from Philadelphia, two hundred and forty-eight miles from Pittsburgh, and ninety miles from Baltimore, and has running through it the Pennsylvania, Northern Central, Philadelphia and Reading, and Cumberland Valley Railroads, and the Pennsylvania Canal. Surrounded by a thickly settled farming country, from which to draw native labor, within easy distance of anthracite and bituminous coal, with ores and limestone near at hand, and with the Susquehanna River as a never-failing water supply, Harrisburg has advantages for manufacturing which warrant the investment of the capital that has already been made, and has a future as a manufacturing city second only to Pittsburgh and Philadelphia. THE PENNSYLVANIA STEEL COMPANY, L. S. BENT, SUPERINTENDENT. The works of this company, the largest in Harrisburg, lie between the Pennsylvania and the Philadelphia and Reading Railroads, on. the Pennsylvania Canal, and are essentially devoted to the manufacture of Bessemer steel rails. Capital stock, $2,000,000; invested in business, $5,000,000; wages per month, $80,000; employs 2000 men; capacity, 100,000 tons of rails per year, which is being increased to 130,000 tons. The plant, as it now stands, comprises five Bessemer converters, two 7-ton and three 8-ton converters, two 15-ton open-hearth furnaces in operation, and two 30-ton open-hearth furnaces in course of construction, one blooming mill, one rail mill, seven steam hammers, two blast furnaces in operation, two blast furnaces in course of construction, foundry, pattern $hop, machine shop, blacksmith shop, and frog shop, and merchant mill in course of construction. Bessemer No. 1 was built in 1865, with two 7-ton converters, 2 spiegel cupolas, 3 feet diameter, and 3 iron cupolas 6' 6" diameter,

Jan 1, 1882

By H. M. Smith

[ ]

Jan 1, 1927

By M. Howard Berliner

The Harding pegmatite dike is well known for the production of spodumene and lepidolite in the period 1920 to 1930. It attained greater prominence during the last war by being the largest producer of domestic tantalum ore from the rare mineral microlite. The deposit is believed to be the only proved reserve of tantalum ore in the United States today. In 1943 the main portion of a large tantalum-bearing zone in the Harding dike was developed by the Bureau of Mines with the assistance of the Federal Geological Survey. Analysis of this zone from 39 diamond drill holes and quarry exposures showed a large deposit containing 2 pounds of microlite per ton and 21 percent spodumene, In September 1948, the Bureau of Mines resumed development of the deposit with a view to extending the tantalum-bearing zone farther to the southwest or delimiting the ore body. Seven diamond-drill holes failed to penetrate the ore zone in its southwestward projection, Much of the following general information is summarized from the report on the first exploratory work of the Bureau of Mines by John H. Soule.2/

Jan 1, 1949

By Singareddy R. Reddy, Ramana G. Reddy

"The Margules equation is used for interpreting excess Gibbs energy of several ternary systems. An expression for the activity coefficient of a dilute solute, 2(oxygen), in a binary solvent 1-3 is derived. It is used to calculate the logarithmic activity coefficient of oxygen in Pb-O-Gu, Pb-O-Bi, AgO- Sn, Pb-O-Sn and Ag-O-Pb metallic systems. Self interaction parameter of the solute is derived from the partial Gibbs energy of solute using constant compositional path. The derived equation is used successfully to deduce the self interaction parameter of oxygen in Pb-O-Gu and Pb-O-Bi metallic systems. The predicted thermodynamic parameter data i.e activity coefficient and self-interaction parameters are in an excellent agreement with the experimental data and also our predictions are far more accurate than the predictions made by other models.1 IntroductionThe nature of solute interactions such as oxygen, nitrogen and sulfur with the metallic solutions are important for a number of chemical and metallurgical processes. Several theories [1-23] have been developed to evaluate fundamental thermodynamic properties of solutes constituting two elements. The activity of solutes has been calculated using statisticalor quasi- chemical approach.Wagner's [4] Ideal Solvent Model is based on one energy parameter to describe the compositional dependencies of the activity coefficient of nonmetallic solutes such as oxygen in binary metallic solutions. This model depends on a constant energy of interaction for the exchange of atoms from the coordination shell of an oxygen atom to the shell of an interstitial site and cannot account for properties of strongly interacting systems [4]. Therefore, several attempts have been made to improve the Wagner's model for the strongly interacting systems. [10-16]."

Jan 1, 1996

By A. P. Pavia

Investigation on profitable ways to recover significant quantities of silver remaining dissolved in highly concentrated chloride solutions frequently pass through the development of solvent extraction (SX) routes. In this work, the general pathways involving Ag(I) extraction by dibutylthiourea (DBT) or tetraethylthiuram disulfide (disulfiram, DSF), from concentrated acidic chloride solutions, are investigated. With this purpose, the dependence of Ag(I) distribution coefficient on ligand and chloride concentrations has been analysed. Furthermore, in order to check whether there is some protonation at any site of DBT or DSF after contact with adequate chloride phases, lH NMR has also been used. The collected spectroscopic data suggest that anionic Ag(I) extraction reactions are not likely to occur. Based on the overall results achieved, proposals for the most probable Ag(I) extraction reactions are made.

Jan 1, 2001

By B. N. Church, R. H. Seraphim, J. T. Shearer

"The Lexington-Lone Star CU-Au deposits straddle the Canada U. S.A. border, south of Greenwood, British Columbia. This 3 km long linear porphyry system occurs in a northeast dipping belt of sheared quartz porphyry and serpentinite. The best grades of mineralization occur in three principal bodies known as the Pit zone, the Northwest zone and the Lexington Main zone. The Pit zone at the Lone Star mine is the largest of the mineralized bodies and consists of fracture fillings and disseminations of pyrite, chalcopyrite and minor molybdenite, hosted by the Lexington quartz porphyry. The Northwest zone, discovered by drilling through overburden near the 49th Parallel, consists of pyrite-chalcopyrite-gold mineralization in the quartz porphyry and the footwall serpentinite. The Lexington Main zone has the highest grade of gold and occurs near the footwall of the quartz porphyry with the mineralogy and setting similar to the Northwest zone. Alteration of the host quartz porphyry is mostly sericitic and chloritic; alteration in the adjacent serpentinite is mostly talc and carbonates.A weighted average of the drill-indicated reserves is 19.5 million tonnes grading 0.56% CU and 0.55 gl t Au.IntroductionThis paper describes copper-gold mineralization associated with the Lexington quartz porphyry in the Greenwood mining camp of south-central British Columbia and adjacent parts of Washington State (Fig. 1).Access to the property is mainly by a network of farm, logging and old mining roads to the U.S. border, 10 km south of Greenwood, British Columbia."

Jan 1, 1995

By I. Perus, M. Fazarinc, G. Kugler, M. Tercelj

"Ledeburitic tool steels are highly alloyed steels used for specific highly loaded applications but are characterized by low and variable hot workability. In this contribution the importance of selecting the right choice of some essential process parameters, i.e. casting temperature, solidification rate and soaking temperature, needed for improving the intrinsic hot deformability of ledeburitic tool steels, is studied. An inappropriate selection of casting temperature and cooling rate results in precipitation of unusual eutectic carbides that decreases the hot workability, whereas with the selection of appropriate soaking temperature the temperature range of safe hot working can be broadened. For each initial as-cast microstructure individually determined soaking temperature should be selected.IntroductionThe surface cracking during hot deformation of ledeburitic tool steels reduces mechanical properties and their industrial yield. These tool steels have high hardness, wear resistance and high tempering resistance on one hand, and high flow stresses and low hot deformability on the other. Decreased hot deformability of the tool steels is attributed to the type, size, shape, distribution, fraction of eutectic carbides and/or other phases, grain growth, etc. at upper limit while precipitation of secondary carbides and decreased recrystallization rate at lower limit of the safe hot deformation temperature range, [1-6].The occurrence of cracks on most exposed areas of workpiece are related to the areas where similar conditions related to upper and/or lower limit of temperature working range prevail, i.e. areas with accelerated cooling, areas with higher value of accumulated strains where also decreased recrystallization rate with simultaneously presence of higher tensile stresses takes place, furthermore areas of workpiece which are due to combustion conditions in furnace heated to higher temperatures, etc. Thus the areas, where combination of previously mentioned conditions prevails, are more exposed to cracking. This additionally requires that hot deformability of ledeburitic tool steel should be considered as a complex problem. Publications in the literature with regards to hot deformability of tool steels are predominately of a partial nature thus all reasons for unexpected occurrence of cracks are not sufficiently explained in available literature so far. Furthermore modern practice proves that previous processing parameters significantly influence the hot deformability and thus this cannot be considered as a constant value. During heating, soaking and hot deformation various processes take place: decay (decomposition) of carbides, formation of new carbides, dissolution of carbides and of alloying elements, etc. Thus depending on variation of process parameters and chemical composition, that consequently influences the processes related to carbides, shifting of decreased deformability at both limits of temperature working range to higher and/or to lower temperatures can occur, [1-14]."

Jan 1, 2012

By Y. G. Seredkin, A. A. Vasiliev, A. Y. Senchenko, A. V. Aksenov

"The valuable materials resulting from the processing of gold-bearing ores are often refractory to direct gold recovery through cyanidation. There are multiple methods for chemical liberation of gold prior to cyanidation such as pressure and biological oxidation as well as atmospheric oxidation which is typically used in combination with physical activation of material by ultrafine grinding such as the Albion ProcessTM. This paper will examine the data from process testworks carried out to estimate the efficiency of the Albion Process™ for the oxidation of materials with a wide composition range prior to cyanidation. The data will be compared to that obtained by direct cyanidation of the feed (without oxidation) and from the testing of pressure oxidation on the feed prior to cyanidation. Albion Process™ tests were conducted in Institute TOMS with participation of Glencore Technology Pty Ltd (Australia). Refractory concentrates obtained from the ores of several Russian and CIS deposits were used as feed for the testing. These concentrates were also subjected to a material composition study and testing using conventional recovery methods. The resulted test data make it possible to perform an integrated assessment of process properties for materials with different compositions, compare performance of various process flowsheets for the materials under study, and conclude on efficiency of Albion Process™ application for gold recovery from refractory materials different in their composition.INTRODUCTION It is often the case that gold ore concentrates are refractory to gold recovery by direct cyanidation. This refractory nature is as a rule attributable to fine gold dissemination in minerals, most often in pyrite and other sulphides, as well as to the increased amount of components impeding cyanide leaching of gold due to cyanide consumption and reducing process conditions. The refractoriness of the concentrates results in low gold recovery values when conventional cyanidation technology is used. In this context, various additional processes are applied to breakdown such refractory sulphide concentrates, i.e. mechanical breakdown (fine and ultrafine grinding), chemical breakdown (atmospheric oxidation, e.g. Leachox, acid-oxygen oxidation, pressure oxidation – POX, bacterial oxidation – BIOX), and thermochemical breakdown (various roasting methods). Such breakdown processes allow for increase in recovery of finely disseminated gold during the downstream cyanidation, however, their application is cost-intensive and does not always ensure economic benefit."

Jan 1, 2018

By Zhan Zhang, Hiromi Nagaumi, Zhen Li

"Recently, the remarkable strengthening effect of ??-Al(Mn, Fe) Si dispersoids at both ambient temperature and elevated temperature were found by several researches. A large amount of dispersoids can be formed by applying special heat treatments and within a suitable range of chemical composition of AA3xxx alloys. In the present work, the influences of Cr addition on the mechanical properties and microstructures of the Al-Mn-Mg-Si alloys were investigated. The mechanical properties at ambient and elevated temperatures were evaluated by micro-hardness and yield strength. Moreover, the microstructures in as-cast and heat-treated conditions were quantitatively analyzed by optical and electron microscopes. Results revealed that Cr also had effect on the number density and volume fraction of dispersoids. Micro-hardness and yield strength at ambient temperature increased with the increasing content of Cr, and the Cr addition increased the yield strength at elevated temperature as well. Moreover, the creep resistance at 300°C improved dramatically with the increasing content of Cr.INTRODUCTION Traditionally, AA3xxx aluminum alloys were widely used in packaging, automobile and architecture industries, because of its good formability, excellent corrosion resistance and weldability. And AA3xxx alloys were considered as non-heat-treatable alloys. However, the strengthening effect of dispersoids in AA3xxx alloys was discovered recently (Li & Arnberg, 2003;Li, Muggerud, Olsen, & Furu, 2012; Li, Zhang, & Chen, 2016; Liu & Chen, 2015).Alarge amount of dispersoids could precipitate by a proper heat treatment.In order to further improve AA3xxxalloys, the composition of the alloys should be optimized. A few previous studies were reported to investigate the influence of compositions on AA3xxx alloys. Adding Mn element could enhance the precipitation of ??-Al(Mn, Fe)Si dispersoids and improve the yield strength(Muggerud, Mørtsell, Li, & Holmestad, 2013), as long as the concentration of Mn was under the solid solution limit. Fe decreased the solubility of Mn and accelerated the precipitation rate of ??-Al(Mn, Fe)Sidispersoids(Li & Arnberg, 2003), the yield strength and creep resistance at elevated temperature could increase with an optimized content of Fe(Liu & Chen, 2016). Mg element would affect the nucleation process of ??-Al(Mn, Fe)Sidispersoids by forming metastable Mg2Si(Hirasawa, 1975; Li, Zhang, & Chen, 2017a; Lodgaard & Ryum, 2000), metastable Mg2Si precipitated during heating process and promoted the precipitation of ??-Al(Mn, Fe)Sidispersoids, moreover, Mg provided solid solution strength for AA3004 alloys(Li et al., 2016). Si increased the volume fractionof ??-Al(Mn, Fe)Sidispersoids(Muggerud et al., 2013)and decreased the size of ??-Al(Mn, Fe)Sidispersoids(Li, Zhang, & Chen, 2017b). With the addition of Mo, the size of dispersoids became finer with a higher volume fraction, the volume percentage of dispersoid free zones was reduced. Elevated temperature yield strength and creep resistance improved due to Mo addition (Liu, Ma, & Chen, 2017).However, the effect of Crelements on microstructure and mechanical properties of AA3xxx alloys were rarely reported."

Jan 1, 2018

By F. C. Gibson

An electrical method for the continuous determination of propagation velocities in opaque, confined explosives, and propellants is described. A resistance element imbedded in the reactive material generates electrical signals that are displayed oscillographically and indicate the position and progress of a reactive zone associated with progress of a reactive zone associated with burning or detonation. The method is applicable to both solids and liquids.

Jan 1, 1963

By E. V. Zelinskaya

"Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production. Considerable attention in recent decades has been given to waste recycling. The task is to maximize the use of both newly formed and accumulated solid and liquid wastes. The mining and mining and smelting enterprises industrial waters are a very promising source of secondary hydromineralic raw materials. They have high concentrations of not only calcium, sodium, but also, for example, lithium, rubidium, heavy non-ferrous metals. In general, unfortunately, we have to state that today there is no wide practice of extracting valuable components from waste enrichment, as well as processing of man-made waters to extract metals from them. The quantity of extracted components from underground, and furthermore passing waters, is insignificant. At the same time there is a tendency to increased demand for rare metals: Sr, B, Br, I. This is explained by their wide use in many industries. For example, the consumption of lithium products is steadily increasing. The obtained results showed that in the liquid phase in connection with high salt content and a significant difference in the macro- and microcomponents contents, conditions are initially created for the microcomponents selective isolation possibility. The identified conditions realization is most possible in such technological processes as cryotechnology, sorption and ion flotation. There is an urgent need to expand research in this direction and to recognize as a publicly important task the mining and industrial waste processing full-scale introduction into the practice of operating mining and processing enterprises and iron and steel companies.INTRODUCTION Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production."

Jan 1, 2018

By S. P. Nagaeva, O. U. Poperechnikova, A. V. Kuptcova

"In case of free gold presence in ore, there is always problem of a choice between the gravity-flotation and gravity separation flowsheets. Study of morphology of gold being extracted by different methods allows to find the most efficient solution. One of the latest methods of gold concentration for wide range of grain size (-0.8+0 mm) is a flash flotation. The paper presents comparative testing results of flash and centrifugal separation.The goal of the studies was to determine process and flotation parameters of flash flotation. In case valued minerals are soft if compared to host rock, such minerals tend to concentrate into circulating load of grinding circuit. Thus, valued minerals can be overground, and in turn, will result in low extraction in flotation circuit. Integration of flash flotation operation into process flowsheet has been evaluated. Flash flotation operation can be successfully used not only for gold but also copper, lead, nickel and silver minerals.With low-sulphide ores being a case study under laboratory conditions, various flotation (impeller rotational speed, air flowrate) and process (pulp density, collector consumption, frother consumption, time of flotation) parameters were studied in view of its impact on gold flash flotation. Experiments were carried out under laboratory conditions using special pneumatic mechanical flotation machines.INTRODUCTIONGravity separation is used for extraction of coarse gold before cyanidation and before flotation of polymetallic ores to increase gold total recovery into gravity copper and lead concentrates.Benefit of the flash flotation is efficient recovery of coarse gold carrier particles (sulphides) thus preventing its regrinding and, as a result, low recovery. Furthermore, combination of flash and conventional flotation results in final tailings that do not require further cyanidation.Combined gravity-flotation flowsheets are designed for concentration of ores containing gold within thewide range of grain sizes (see Table 1)."

Jan 1, 2018

By V. S. Sastri, Elboujdaini. M.

"Economics of wear in mining industry and methods by which wear cost may be reduced will be discussed.IntroductionCanada loses more than $5 billion annually due to friction and wear (Table 1). It is estimated that about $1.3 billion, or about 25% of the losses, could be saved through better application of existing technology (Table 2). It should be noted that the costs given in Table 1 and 2 refer to 1986. The losses due to friction and wear and the savings would be much higher in 1996. Tribology combines the many branches and specialties in science and technology concerned with understanding and combatting friction and wear. Specifically, tribology is concerned with the design and manufacture of sliding and rolling bearings, piston rings, gears, cutting tools and other devices in which surfaces interact, in sliding or other relative motion. Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of the surfaces with the lubricants, with the chemistry, physics and use of lubricants. It is concerned with the reduction of friction and wear and the avoidance of associated failures in machinery. Similar tribological components such as bearings are used in different technologies and similar tribological problems such as abrasive wear occur in different industries. Thus, tribology is in itself a generic science and technology, concerned with the generation and dissemination of knowledge on friction, wear and lubrication, and the application of the knowledge, to a wide range of industrial products and equipment, from ploughs to space equipment, from prosthesis to engines, from washing machines to railways, from computers to power stations, from paper mills to mines. Avoidable losses due to friction and"

Jan 1, 1997

By K. Barbetti

"The carbon-in-pulp (CIP) process has been the dominant gold recovery process since the early 1980s. CIP has proven to be very adaptable for a wide range of ores and circuit configurations. The key performance indicator for CIP circuits is the minimisation of soluble gold losses to tailings, however, it is also important to operate the circuit efficiently (maximising gold loadings on carbon and minimising carbon inventory). Over the last 30 years the Curtin Gold Technology Group has studied CIP circuits as part of an on-going collaborative industry funded project (the AMIRA Gold Processing Technology Project). In the early years the project undertook basic research into understanding activated carbon, and its management in the circuit. More recently the development of process models and instrumentation has provided additional tools to assist operators. The results show that while most CIP circuits operate well, there are still significant opportunities for further cost savings, or additional revenue. This paper reviews the observations arising from this work, including key requirements for good carbon management, the results of benchmarking and industry surveys of carbon circuit over 20 years, the value of process modelling of CIP circuits to establish operating parameters, and the use of automated instrumentation to better optimise carbon control in the circuit.INTRODUCTION The introduction of activated carbon to recover gold from cyanide leach solutions in the last quarter of the 20th century was the most significant development in gold ore processing since the advent of cyanidation seventy years before. Replacing the Merrill–Crowe zinc cementation step with carbon-in-pulp (CIP) or carbon-in-leach (CIL) circuits provided a process that allowed the treatment of lower grade and problematic ores (e.g. high-clay ores), at lower capital and operating costs, and higher metal recoveries. The CIP circuit was first developed in the 1950s at the Carlton Mill, Cripple Creek, Colorado. All the components of the modern CIP process came to fruition at the Homestake Mine in South Dakota in 1973 (Fast, 1988). From the late 1970s onward a variation of CIP, carbon-in-leach (CIL) which combined the leach and adsorption stages, became the preferred circuit design in most parts of the word."

Jan 1, 2017

By Robert J. Hundhausen

This report describes Bureau of Mines investigations of a low-grade scheelite-bearing granodiorite intrusive situated on Henderson Creek, Granite County, Mont. The intrusive is in a narrow, V-shaped valley at the head of extensive placer workings. Since May 1943 the H. & R. Mines Co. of Portland, Oreg., has recovered scheelite sand and gold from the placer workings. A modified Yuba, 4?cubic foot bucket dredge was used in the operation. By February 1947 this operation had recovered and marketed over 215,000 pounds of scheelite concentrates containing 63 percent WO3. The scheelite in the placer was found to be derived principally from erosion of the granodiorite intrusive. The intrusive is one of a series of four similar, dikelike masses of granodiorite whose outcrops are aligned along a 10-mile zone of weakness trending N. 60° E. The intrusive has a triangular outcrop exposed over an area of 57 acres. Trenching and sampling by the Bureau of Mines demonstrated that scheelite is sparsely distributed throughout the granodiorite. This work delimited the outcrop of the intrusive and indicated a large submarginal reserve of low-grade tungsten mineralization. The deposit is ideally suited for exploitation by large-scale, open-pit mining operations; it would be easily available in a national emergency. Additional exploration would be necessary, however, before large-scale production plans could be made efficiently or accurately.

Jan 1, 1949

By Hamid N. Maleki

Cooperative efforts by the Bureau of Mines and Agapito & Associates, Inc., Grand Junction, CO, achieved the research objective of showing that data from measurements of the rate and change in rate of mine roof movement can be effective in detecting roof instability. Several instruments and techniques have been used to monitor roof movement and to detect imminent roof caves during pillar robbing. Early detection of unstable conditions can provide time either to withdraw personnel and equipment or to allocate supplemental support to prevent injury or down-time. Critical convergence rates were determined both manually and electronically. The detection of critical rate of movement has been shown to be an effective tool in ground control efforts.

Jan 1, 1988