Search Documents

By M Malec, J Szczerbinski

Hazards in underground mines are concomitant with the mining of mineral deposits and have their source in a minerÆs work environment. The authors of the paper have undertaken a trial classification of these hazards into three groups, depending on the sphere of their occurrence:lithosphere, ie rock mass, atmosphere, ie air in mine workings, and technosphere, ie machines, equipment and facilities in mine workings. The lithosphere creates such hazards as bumps, rock outbursts, the atmosphere is a factor causing fires, methane explosions and climatic hazards, whereas accidents concomitant with an operation of machines and equipment occur in the technosphere. Assuming that the number of accidents in the mining industry, concomitant with hazards, reflects the degree of safety, it has been shown, that in Poland they are under control to a large extent.

Jan 1, 1999

By F. E. Senftle

Preliminary geophysical surveys for nickel deposits are usually carried out by airborne magnetometer and surface electrical methods. Once an anomaly is discovered by these techniques, one must resort to chemistry to identify nickel and determine its concentration. Consequently, a method to determine nickel quickly and quantitatively at the exploration site could help guide detailed sampling and provide analytical data that might otherwise be delayed at distant laboratories. In addition, borehole probes capable of indicating nickel in the rock adjacent to the hole, should prove attractive to the exploration geologist. With these needs in mind, preliminary investigations have been made to demonstrate an in situ analytical technique which appears feasible for nickel exploration. The method depends on the very high energy gamma rays emitted when nickel absorbs a thermal or low energy neutron. These neutron capture gamma rays should be distinguished from the lower energy gamma rays emitted during decay of radioactive nuclides as in conventional activation analysis.

Jan 1, 1971

By Karsten Zimmermann, Peter Cain

"To receive regulatory approval for a new coal mining operation in North America, extensive investigations of feasibility and potential environmental impacts, including ground deformations, are required. Figure 1 shows pictures from mine sites and an example mine map with the planned panel layout for one seam of the multi-seam longwall operation considered.The cumulative mined coal thickness of 22 meters in some areas of the operation requires a comprehensive forecast of expected ground movements and subsidence impacts (e.g., subsidence, slope, displacement, curvature and strain). In the frame of the impact study, the prediction of these impact factors was conducted by DMT using the computer program SPS 4D, based on the Ruhrkohle modeling method by Ehrhardt and Sauer (1961).This paper briefly presents the modeling method and explains the benefits and possibilities for its international application. Information gathered from literature studies on subsidence in North America were incorporated into the initial model parameterization. The article shows the ways in which the observed influences of mountainous topography on surface displacements and deformations can be considered by an extension of the subsidence prediction model and integration of DEM information.SUBSIDENCE MODELFor the calculation of mining-induced subsidence and deformation, DMT has developed subsidence prediction software SPS 4D, which is built according to the stochastic prediction model by (Ehrhardt and Sauer, 1961). The model is based on the subsidence theory by (Knothe, 1953) with a specific parametrization of the stochastic influence function and includes enhancements for dynamic subsidence calculations after (Sroka, 1978). In Europe, mainly in Germany and Poland, the model is approved by the authorities as a standard model for subsidence prediction in mining areas. However, extensive research within R&D activities has shown the possibility to predict mining-induced subsidence considering the specific mining conditions in North America (Zimmermann and Fritschen, 2007)."

Jan 1, 2016

By F. S. Niu

With the feature of finely-dissemination particle and complex mineral composition, oolitic hematite is considered to be the ore dressing difficult problem in the world. Series research on refractory oolitic hematite in Zhangjiakou Area are introduced as following: ore properties?technology mineralogy and mineral processing technology. The survey shows: with the fine grinding of the hematite to a fineness of -0.076mm 95%, obtaining iron concentrates grading 62.74% Fe at the recovery of 46.80% by high intensity magnetic separation- reverse flotation flowsheet; under the three stages intensity magnetic separation,four stages grinding and four stages gravity separation, getting the iron concentrates grading 61.09% Fe at the recovery of 45% using high intensity magnetic separation- gravity separation flowsheet; with roasting temperature of 800°C, time for 75~90min and ore-coal ratio of 11, gaining the iron concentrates assaying 62.74% Fe at the recovery of 87% by roasting- magnetic separation flowsheet. At present, this research is still doing for the target of raising the concentration recovery on the base of high grade concentrate. It is in the hope of fully utilizing the existing hematite resources in Zhangjiakou

Jan 1, 2014

By R. C. Miranda

Flotation is an operation widely used in mineral processing because of its aptitude to recover minerals of interest very efficiently. Flotation is often responsible for making possible the exploitation of mineral deposits of low concentration. In flotation various processes phenomena occur, some of which have still not been explained scientifically. Due to this fact, there are no models that can be widely applied in flotation control. Thus, in most cases, the control is done by experienced operators who are able to visually classify the types of foam into different categories and each one of them is associated with an operating actuation. In this situation, image analysis is configured as a solution that has already been employed in several ways. In this paper, a control strategy based on the colour of froth on a direct flotation of a nonferrous metal is presented. Moreover, the paper reveals the theoretical basis of the method, the critical points, difficulties and improvements that can be implemented. Data of grade were collected from the mineral of interest and RGB (red, green and blue) data of final concentrate of the froth. The mineral grade was collected and analysed during one month of operation and RGB was obtained using a camera. It was verified that the red colour showed the same trend of the grade curve in the concentrate. Thus, the use of this online data in optimising control was introduced. The laboratory grade is used to calibrate the colour set point. Therefore, it was possible to monitor in real time the trend of enrichment and depletion of a non-ferrous mineral in a flotation. It was possible to establish an online control strategy based on simple data acquisition. The result was an increase of 10% on production.

Sep 1, 2012

By T. J. Ballard

The Ore Knob mine, in Ashe County, N.C., was one of the largest producers of copper in the eastern states during the 1870's. The ore occurs in a fissure vein, which strikes N. 64° E. and dips nearly vertical. The country rock is granite gneiss. Drilling indicated that the vein structure is approximately 200 feet wide and 1,500 feet long. The vein material shows evidence of replacement of the original gneiss by sulfides. Solution cavities in the vein were noted in some places. The ore minerals and pyrrhotite, chalcopyrite, pyrite, and minor quantities of sphalerite. The gangue contains biotite, magnetite, albite, calcite, and many silicate minerals.

Jan 1, 1948

By Juan Munar Calderon

El presente texto revisa la función de la empresa de comercialización de productos mineros (MINPECO), su importancia en la economía nacional y los principales resultados alcanzados por la comercialización estatal. MINPECO es una empresa encargada de la comercialización interna y externa de productos mineros, cuyo funcionamiento está normado por su ley orgánica, disposiciones legales relativas a las empresas públicas, sus estatutos y los reglamentos internos de la empresa. El sistema actual de comercialización comprende modalidades de compra-venta, contrato de terceros, conversiones y las relaciones financieras. Asimismo se describe el ingreso de divisas y ventajas de la comercialización estatal.

Nov 20, 1978

By S. Shairp

"After cooling and thickening, slurry from the second stage of the Hudbay zinc pressure leach circuit is filtered and washed on a belt filter prior to disposal. At times, the belt filter can be a bottleneck to the process. Preliminary studies show that filterability of the second-stage (HAL) autoclave leach residue can be indicated by particle size distribution of the filter feed and filtered residue cake. In particular, the Volume Weighted Mean Diameter, D[4,3], generated by a laser diffraction particle size analyzer from samples of HAL Filter feed, shows residues that filter more poorly have a lower Volume Weighted Mean Diameter than those that filter better. INTRODUCTIONHudbay produces cast zinc metal from blends of zinc concentrates at its metallurgical complex in Flin Flon, Manitoba, Canada, using Sherritt’s two-stage pressure leach process (Collins et al., 1994; Collins et al., 1995; Barth et al., 1998; Shairp et al., 2006). Pressure leaching replaced the original roastleach- electrowinning process in 1993.Filtration for the second-stage (HAL) leach residue originally consisted of two stages of vacuum drum filtration with intermediate cake repulping stirred tanks. As part of Hudbay’s 777 Project, with a designed increase in cast zinc production, a pre-feasibility study by SNC-Lavalin Inc. showed that losses of soluble zinc in the zinc pressure leach residue could be reduced by installing more efficient filtering and washing equipment. Based on laboratory performance, capital cost, installation ability, and potential operating cost savings, a 70 m2 Filtres Phillipe belt filter was chosen for the HAL residue, and commissioned in 2000/2001.When the HAL belt filter is performing well, there is no pooling of water on the surface, moisture content is relatively low, and subsequent analysis shows that water soluble zinc content is relatively low. There have been occasions where the filter has performed poorly with respect to the aforementioned parameters. Aside from the filter experiencing mechanical difficulties, there are several variables affecting leach residue filtration:"

Jan 1, 2012

By P. J. Uggowitzer, H. Kaufmann

"New Rheocasting is a novel route of semi-solid casting, in which the globular semi-solid precursor material is produced by controlled cooling of only slightly superheated melts in conventional steel crucibles. The resulting semi-solid slugs are placed into the sleeve of a vertical Squeeze Casting Machine and then filled into steel dies. Solidification occurs under hydraulic pressures up to 100 MPa Due to the reduced cost of precursor material, reduced investment cost and easier recycling, the New Rheocasting process offers cost reductions of up to 25% over conventional semi-solid casting · routes. The New Rheocast products are pore free, pressure tight, weldable and heat treatable castings.In the present work the New Rheocasting Process is introduced and the influence of heat treatment on mechanical properties of the New Rheocast alloy A356 is discussed.The alloy A356 is cast under ideal New Rheocasting conditions into a step die on an UBE HVSC 350 Squeeze Casting machine. As-east, TS and T6 heat treatment conditions with variations in solutionizing and aging time/temperature parameters are applied and the samples are tested by tensile testing. Alternatively, the same heat treatment conditions are applied to conventional Squeeze Casting parts and compared with New Rheocasting.Questions of potential cost savings due to modified heat treatment conditions are also addressed in this paper."

Jan 1, 2000

By J. B. Malcolm

The discovery of tungsten-bearing quartz outcroppings in Vance County, N. C., by the Hamme brothers in 1942, made international news in the mining industry and was, in fact, one of the major ore discoveries made in the U.S. during the last 25 years. Operations began at the Hamme mine in 1942, but after 16 years of successful operation, the mine was closed down in 1958 under adverse market conditions. By that time, it had produced nearly 20 million lbs of metallic tungsten. Because of the square-set timber mining method then in use, mine operating expenses were high, actually representing 78% of the total operating expenses at the property. In timber work alone, 160 men were employed. Approximately 500,000 bd ft of timber were placed monthly at a direct supply cost of $1.00 per ton of ore mined. Late in 1959, following a slightly improved position in the tungsten market, company management decided that, by changing the mining method, the operation could be economically feasible. The major premise in this decision was that a reduction of from 25 to 30% of the mining costs could be achieved by the conversion of the mining method from square-sets to horizontal cut and fill. Reopening of the mine began in February 1960, Full production has now been reached and overall mine productivity has been doubled.

Jan 1, 1962

By T. W. Camm

The Bureau of Mines conducts studies of the economic impacts of regulations on federal lands. These studies are part of the Bureau Potential Supply Analysis (PSA) program. To meet the needs of these studies, a methodology was developed to estimate operating and capital costs for a mineral deposit given its tonnage, grade, and depth. The format for the cost models in this study was developed at the Bureau's Western Field Operations Center (WFOC), Spokane, W. A., for studies of known and undiscovered resources on Federal lands. These cost models are described in a Bureau publication by Camm (1991).

Jan 1, 1993

By Gennady I. Gulyayev

A mathematical model of plastic deformation occurring in cold plug drawing of mother tubes with initial cross-sectional wall thickness variations (CSWTV) has been developed. The main provision of the model is that eccentricity em is of such value that projection of all forces acting upon the plug in the deformation zone along the axis perpendicular to the drawing axis equals to zero. Calculations have proven that with other conditions being equal increase in the die cone angle and the deformation cycle number reduces CSWTV. Theoretical findings were confirmed by practical results. Keywords: cold, drawing, plug, die cone, plastic deformation.

Jan 1, 2003

By Z Tong, M Gao, X Wang

In response to the need for improved magnetic separators for beneficiation of fine grained iron ores that have been finely ground to liberate the iron minerals from the gangue, a series of high efficiency wet drum permanent magnetic separators (T-GCT) has been developed by Maanshan Tiangong Technology Co Ltd. These magnetic separators have high efficiency for separating superfine strongly magnetic minerals and the ability to produce high-grade concentrates with high recovery. They are ideal replacements for conventional drum magnetic separators, especially for treating superfine particles.

Jan 1, 2009

By Liu Wenyong, Huang Yucheng, Yang Ba

High-water rapid-solidifying material, called æhigh-water materialÆ, is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of backfill body, environmental contamination and so on, have been solved.

Jan 1, 1998

By Eiji Iwamura

"Two types of diamond-like carbon (DLC) films with different microstructures were prepared by unbalanced magnetron sputtering, and the tribological properties of the nanoscaled DLC multilayer coatings consisting of alternating layers of graphitelike and amorphous-like microstructures were examined. The DLC microstructure was characterized by certain features of graphite-like clusters, in that some of them had onion-like structures. The films filled with the clusters were obtained in a condition with an incidence of high influx of energetic electrons, and the other films without apparent cluster structures were formed in a condition with ion bombardment controlled by negative bias voltage applied to substrates. Stacking each film layer-by-layer, the nanoscaled multilayered coatings showed superior tribological properties to individual single-layered films due to the combination of properties induced by the difference of microstructures.IntroductionIn various tribologiql applications, it is necessary for diamond like carbon (DLC) coatings to have adequate adhesion, significant hardness and a concomitant low friction coefficient. A number of deposition techniques and coating structures have been proposed to achieve suitable DLC properties [1-3]. However it is still difficult to obtain a satisfactory level of combination of the properties particularly desirable for engineering applications.In this study, the features of unbalanced magnetron sputtering were demonstrated with the effect of ion and electron bombardment. Two types of microstructures , namely amorphous-like and graphite-like, were prepared by changing the condition of the charged particles bombardment during deposition. Using the difference of properties induced by the microstructures, nanoscaled DLC multilayered structures were examined in an attempt to improve tribological properties."

Jan 1, 2000

By John G. Oldsen

During the last several years, implementation of trusses, in lieu of wood cribs, has been successful for supplemental tailgate support in the Pittsburgh seam. This paper reviews the truss support system provided by the new high strength 0.6" tensioned cable truss, which is now also being used in cribless tailgates. Cable loading and roof deformation were monitored to evaluate roof and floor performance. The test results indicate that the cable truss system successfully controlled the roof and floor during the first and second panel extraction. This paper will describe the advantages of cable trusses and their load transfer mechanism as well as mine evaluation.

Jan 1, 1997

By Wen Chen, Xinghua Liu, Zeyou Peng, Qiulin Wang

"Limonite is a collective for iron hydroxide argillaceous materials. It is very difficult to be treated due to the wide variation in specific gravity and magnetism and the high argillization rate in the course of grinding and beneficiation. The iron ore in Huangmei, Hubei, China is the typical representative of limonite. If the limonite is processed using conventional physical beneficiation methods (e.g. magnetic separation, gravity separation, flocculation-desliming-flotation, or a combined process of the three), it can only be obtained an iron concentrate grade of 51.98% and an iron metal recovery of 86.64%. However, the technique of flash magnetic roasting-magnetic separation can improve the concentrate grade to 61.03%, iron recovery to 91.17%. This paper describes the tests of recovering limonite by flash magnetic roasting in detail.IntroductionLimonite (mFe2O3, nH2O)[1] is a general designation for hydrous iron hydroxides and argillaceous matters. Limonite is hard to be separated because of its complicated geneses, comparatively weak magnetism, nonuniform grain size and being easily slimed during grinding. So most small and medium enterprises sell deslimed limonite product which was dealt with just by simple methods of washing, magnetic separation or gravity separation and so on. In recent years with the iron ore prices soaring, significant progress was made in mineral processing research of limonite. Laboratory research and industrial test results showed that flocculation-desliming-flotation process and roasting-magnetic separation process are the two best methods to recover limonite till now. To compare these two methods, roasting-magnetic separation process is superior to flocculation-desliming-flotation process in aspects of beneficiation indexes and industrial stability."

Jan 1, 2012

By Ian Bell, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Mahdi Ramezani

"Image-based rock fragmentation sensing in mining and quarry applications includes an important rock boundary delineation step, which is commonly referred to as rock segmentation. This paper presents a novel approach to solve this problem, using artificial intelligence. In the proposed technique, priorknowledge of previously analyzed images is encoded into mathematical/statistical models. A set of human labeled images are used as training inputs. These images are used to train neural networksthrough an optimization process. The networks can then be used in real time for rock delineation. "

Jan 1, 2017

The theory and practice of sampling of particulate material have been the focus of a continued attention on the part of the mining industry worldwide for almost a century now, because of its critical importance at all phases of a mining project, from exploration (bulk sampling, assaying) to production (grade control) and marketing (quality control). A powerful, complete theory was put together by P. Oy (1968 to i982), but its applications to gold ores have met with limited success to date, due to the inadequacy of its sampling variance and minimum sample mass determination formulae to the challenging case of gold ores. This paper presents a research project completed at Inco Exploration and Technical Services Inc., using a geostatistical approach, to shed light on the results of P.Gy's theory, and adapt them to the case of particulate gold ores. After a reminder of Gy's formulae and a simplified demonstration of the generic form of Gy's and more traditional formulae, an empirical approach, based on sampling experiments from four gold deposits, shows how Gy's formulae must be corrected to adjust to the case of gold ores. The generality of the results formula is then substantiated with a geostatistical analysis of the problem. A parameterized formula results, and indications are given on how to fit its parameters to experimental data. Application guidelines and charts to fit any case and budget are presented, along with a detailed practical example.

Jan 1, 1991

By Jorge. Melchiori

En el Perú, la aplicación de los métodos geofísicos para la exploración minera ha sido mínima, a diferencia de las exploraciones de yacimientos petrolíferos, donde su demanda fue mucho mayor. Este diferencia respondería a la poca difusión del mismo, como las escazas pruebas de combinaciones metódicas. Entre los métodos a utilizar, están los sondeos eléctricos verticales y perfiles horizontales), la polarización espontánea( campos eléctricos-naturaleza electroquímica),el método magnético (distribución del campo magnético y perturbación en medición del componente vertical), el electromagnético a inducción(malla horizontal, cuadro vertical), y la emanación en la exploración de zonas mineras (radon, thoron, y actinon).

Jul 20, 1955