Search Documents

The building is a lofty, well-ventilated one of hardwood frame, with galvanized-iron walls and roof, and consists of five spans running north and south, covering a total length of 236 ft. Each span is composed of nine bays of 1:3-ft. centres, making the total width of the building 117 ft. The refinery is situated conveniently at a distance of 100 yds from the smelters. Through the third span of the building runs a 5-ton electric overhead travelling crane, of a 3-motor type, with a span of 29 ft. The crane runway extends over a railway line, which connects the smelters to the refinery. This crane is llsed for handling bullion, coal, melting kettles, lead pumps, &c. A 3-ton crane of similar type, but with a 50-ft. span, runs through the fifth span of the building and also extends over the railwav line alreadv mentioned. This crane is used to load the soft lead into railway trucks, or to stack lead awaiting shipment in the area covered by the crane's operations.

Jan 1, 1918

By B R. Castley

Consumable materials used in mines are often transported to the working areas down shallow angle decline shafts, typically at anywhere between 10¦ and 30¦ to the horizontal. The winding equipment is usually a relatively small single-drum winder and the material is transported in one or more cars, running on rails in the decline. The winding rope is attached directly to the cars, which are mechanically coupled together. For small rock hoisting declines, the cars are replaced with hoppers or skips. The winder is normally of basic design, fitted with only the minimum required safety devices and very elementary brake control. Since these winders are not ælicensedÆ and are usually located in remote areas, the standard of maintenance on the installations is often poor, leading to frequent accidents, resulting in runaways, derailments and broken ropes. These problems can be overcome easily with the application of the rope haulage principle. When large volumes of ore have to be transported to surface, belt conveyors are used on shallow angle inclines, or high-capacity friction winders are used in vertical shafts. Conveyors are limited to inclines no steeper than 14¦ and vertical shafts with large friction or drum type winders are extremely capital-intensive. Rope haulage systems can be used on decline shafts where the inclination is too steep for belt conveyors and too shallow for conventional drum winders. Rope haulage systems also offer a variety of safety, technical and cost advantages over other winding and transport systems. This paper describes the adaptation of the rope haulage principle to modern requirements and, combined with 21st century electronic technology, explains how the principle can be used as an efficient, safe and practical solution to some problems associated with the transport of materials, personnel and ore in mines. The authors describe the designs, methods of operation, safety aspects, automated control, loading and unloading facilities of modern rope haulage systems used for transporting personnel, material and ore. This paper considers a variety of systems already designed for different applications, from small material-only installations to multi-purpose and large rock-hoisting systems with payloads as much as 180 t. It also describes in more detail, a material transporting system recently commissioned in South Africa.

Jan 1, 2005

By Yu. E. Emelyanov, A. V. Bogorodsky, R. N. Nabiulin, S. V. Balikov

"The paper describes the results of the study of gold-copper flotation concentrate atmospheric oxidation at different sizes of material, varying oxidation time, with air or oxygen blow. The study showed the low rate of sulphide oxidation during oxidation of flotation concentrate at a feed size (P98 -74 µm). The coppery recovery into solution was 48%; the recovery of gold by subsequent cyanidation reached 86%. Preliminary flotation concentrate grinding to P98 -20 µm provided oxidation of 90% of copper minerals, 80% of arsenopyrite and 15% of pyrite. The gold recovery by atmospheric oxidation of a fine-ground flotation concentrate increased by 59%, from 36% to 95%, the NaCN consumption reduced by 21 kg/t, from 30 to 9 kg/t. INTRODUCTION Processing of sulphide gold-copper ores and concentrates using conventional cyanidation technology results in higher reagent consumption and lower gold recovery. Destruction of sulphide minerals and extraction of copper from a processed product prior to cyanidation is essential for improving efficiency of precious metals recovery and reducing main reagents consumption. Atmospheric oxidation (AO) is one of the most promising hydrometallurgical methods of refractory gold-copper concentrates processing, along with biooxidation and pressure oxidation. The nature of this approach lies in oxidation of sulphides at 90-95°C, in acidic or alkaline conditions, with bubbling of oxygen or air, after preliminary ultrafine grinding (1-4). The following reactions of sulphide oxidation occur during atmospheric oxidation of a gold-copper flotation concentrate. Pyrite is oxidized with the formation of ferric sulphate (1) and elemental sulphur at low temperatures (2), whereas some portion of elemental sulphur reacts to form sulphuric acid: FeS2+3,75O2+0,5H2O=0,5Fe2(SO4)3+0,5H2SO4; ?G=-1144,02 kJ/mol (1)"

Jan 1, 2018

By V. P. Bystrov

Vanyukov process has been developed and investigated in Russia over the last 25 years. It has been established that various kind of material could be treated in Vanyukov process. The results of the pilot plant trials as well as industrial experience are presented in this paper.

Jan 1, 1993

By A. E. Hall

"This paper summarizes findings of a two-month investigation in Zambia and Zimbabwe and a one-month visit to Britain in1990-1991. United States contacts have supplied information about that country.Zambia's political unrest and severe devaluation, combined with developments in Namibia and South Africa, enhanced staff recruiting problems in the School of Mines. Zimbabwe has a strong and developing mining department. The departments of mining in the United States and Great Britain are readjusting and contracting due to the reduction in the scale of the industry.The above factors are reviewed and their impact on the countries evaluated.IntroductionCanada trains the majority of its mining engineers domestically but a significant number are recruited from other countries. Examination of the qualifications of 200 professional engineers registered in the mining discipline in British Columbia showed that125 received their first degree from a Canadian university, 33 graduated from institutions in the United States and 42 from the rest of the world including 30 from the United Kingdom. This is a rough and-ready sample but it indicates that developments in the education of mining engineers in the United States and in Britain are relevant to the Canadian mining industry.The recent changes in the world economy and political structure have significant implications for the mining industry and for the supply and training of engineers. Change in eastern Europe coupled with the downturn in mining, especially in the European coalfields, has enabled many engineers to travel freely to the West. The low gold price and the legislative changes in Africa that have improved access to education for Africans with the ability to fill responsible positions, have reduced the South African mining industry’s overseas recruitment to a minimal level. The Australian recession has also lowered their recruitment of mining engineers from other countries."

Jan 1, 1993

By Robert G. Ditchburn

Msjflkcisokng During the past sixteen years, GNS Science has developed a number of radiometric methods for dating massive sulfide samples from submarine arc and back-arc volcanoes. This has improved our understanding of the formation of these hydrothermal systems, the frequency and duration of their activity, and assisted marine mineral exploration companies in assessing the economic potential of these deposits that can be rich in copper, zinc and gold (up to 90 ppm Au in some chimneys). The radiometric dating methods that we employ utilize radium isotopes that are extracted from the host rocks without their parent thorium isotopes, by ascending, hot, acidic hydrothermal fluids. When the hydrothermal fluid discharges into cold seawater, chemically similar barium and radium co-precipitate as barite, a common mineral contained within the black smoker chimneys that grow upwards from the seafloor. From the onset of mineralization, the isotopes 228Ra and 226Ra (with half-lives of 5.75 yrs and 1600 yrs, respectively) begin to decay, so that the 228Ra/226Ra and 226Ra/Ba values decrease with time. Thus, samples can be dated using these ratios once the initial values, i.e., the values at the onset of mineralization, have been established, ideally from active chimneys. 228Ra decays to 228Th (half-life 1.91 yrs) and from the 228Th/228Ra values, the growth-rate of individual chimneys can be estimated. The isotope 210Pb (half-life 22.3 yrs) is occasionally used for dating the mineralization, although several samples from a chimney are needed to determine an age from the 210Pb grown from 226Ra, using the isochron technique.

Sep 14, 2011

By P. W. King

The performance of the versatile McNally Wedag horizontal vibratory centrifuge for dewatering ultra fine 0.5 x 0.15 mm (28 x 100 mesh) material has proven to be success¬ful and the results presented herein will examine its capabilities in terms of capacity, solids capture, product moisture, effluent solids, and size analysis. Centrifugal dewatering of fine refuse has proven t to be another application for which this unit has performed exceptionally well.

Jan 1, 1985

By Ajay K. Singh

The surface quality demands for galvanized and galvannealed steel sheets by the automotive and appliance industries have been getting increasingly stringent over the past few years. Intensive efforts by Hot-Dip-Galvanizers to meet these demands have resulted in substantial improvement to the hot dip coating process. However, elimination of zinc bath contaminants which directly affect the coated strip surface quality continues to remain a tough challenge. As part of our effort to improve the zinc bath cleanliness, Inland Steel Company has developed a test method to quantitatively measure the contaminants in incoming zinc spelters and establish a specification for incoming zinc quality. The test is currently being used for auditing the incoming zinc quality. The zinc suppliers are also using this test for quality control purposes. The purpose of this paper is to describe the test method and how it has improved the galvanizing operation at Inland.

Jan 1, 1992

By Barry Hunsaker

I cannot help but be reminded, as I stand here today, of my boyhood years and heritage, both of which are inextricably tied to this very valley and are, in a: bay, apropos of the theme of this Keynote Session. I remember the scarcity of people. For example, 48, 000 in Phoenix and 436, 000 in the State in 1930 and 65,000 in Phoenix and 499, 000 in the State in 1940. Today Phoenix boasts a population of over 500, 000 and the State a population of 1, 500,000. I remember the' lack of facilities, goods and services, including gas and electric power. I recall stories of my grandfather who had the freighting or teaming contract to haul all the supplies and generating equipment, by wagon mind you, up the old Apache Trail to Roosevelt Dam. . .a three day trip from the nearest railhead which, by the way, was not Phoenix, for it did not merit a railhead on those days, but the village of Maricopa approximately 25 miles south of Phoenix. I remember chopping firewood, heating wash water on an open fire in a No. 3 wash tub at the rear of the house and doing my school homework by the light of a kerosene lamp just 25 to 35 years ago within what is now a large metropolitan area

Jan 1, 1965

By O. W. Terry

The Skene mine, in the Elizabeth District, Illinois, produced lead are from 1901 to 1907. Three exploratory holes drilled just north of the mine were said to have penetrated 40 feet of good zinc are. During the summer of 1944, the Bureau of Mines drilled check holes close to what appeared to be two of the three old holes. They also drilled two holes to the south of the mine and one into the core of the deposit. Results of the investigation are given in this report.

Jan 1, 1948

By Donghai Li, Cheng Pan, Xuewei Lv, Mei Liu, Enguang Guo

"Phosphorite is the main raw material for the production of phosphorus in chemical industry. More attentions have been drawn to the phosphorite concentrate beneficiated from low-grade phosphorite due to the decrease of high-grade phosphorite. For another, the agglomeration process is necessary for the phosphorite concentrate after beneficiation process. The mineralogy and sintering process of the phosphorite from Leshan, China were studied in this work. The result shows that the main phases in the phosphorite are fluorapatite (Ca3(P04)3F), hydroxylapatite (Cas(P04)3(0H)), quartz (Si02) and dolomite (CaMg(C03)2). The yield of the sinter increases with increasing the carbon dosage to 7%, and then decreases when it continuously increases. Similar regularities were found for the strength and the content of P20s of the sinter. The best strength of the sinter as well as its P205 content were discovered when the carbon dosage is 7%. Fluorapatite ((Ca5(P04)3)F) is the main phase in the sinter while fuggerite (Ca2MgSiz01) is the main binder phase.IntroductionPhosphorus is an important foundation industrial raw material of national defense industry, food industry and chemical industry, where it is used to produce red phosphorus, phosphonium hydroxide, phosphorus pentasulfide and phosphoric anhydride[l-2]."

Jan 1, 2013

At long last, mining is on the rebound in Minnesota?s Iron Range and the excitement is starting to show. The SME Minnesota Section?s annual meeting was once again held in the heart of Iron Range country, at the Duluth Entertainment and Conference Center on the Duluth waterfront. The conference boasted a record attendance of 475 people and its largest-ever trade show. Appearances by Governor Mark Dayton?s new Iron Range Resources & Rehabilitation Board (IRRRB) appointee, Tony Sertich, as well as a local Fox news crew (see clip on SME website [link: http://fox21online.com/news/duluth-mining-conference-breeds-optimism-tech-innovation]) made clear that a lot of eyes [ ] are on the industry as it dusts itself off from the 2008-2009 recession. While the early years of the 21st century were very good to the Iron Range, the global drop in commodities prices and production left many companies reeling and brought back bad memories of the collapse of the industry in the 1980s. However, two years of solid growth and a rebound to above pre-2008 production levels have let the Minnesota mining industry to relax a little and talk seriously about long-term growth and stability.

Jan 1, 2011

By Miguel Becerra, Daniel Jordán, Jorge Soto, Luis Torres

"Most SAG grinding operations currently use ball sizes between 5.5 and 6 inch maximum size. However, in most cases the use of this ball sizes hasn’t been justified by a phenomenological analysis of the real effect on the grinding process, but rather by trial and error. The analysis of the influence of ball sizes in SAG grinding hasn’t been developed in detail by considering the effect on process parameters inside the mill, grinding efficiency or internal classification. Historically a conventional grinding reference has been made on the empirical procedure developed by Azzaroni (1980). Further to Azzaroni’s methodology, Sepulveda (Sepúlveda, 2007) developed the SPEC methodology, incorporating the ball size effect on the grinding efficiency parameters using a population balance model included on Molycop tools spreadsheets.This paper demonstrates a detailed analysis at pilot scale of the ball size employed in SAG grinding and scaling that exists between the different levels. This analysis includes assessing the effect of balls sizes on parameters associated with grinding efficiency and its effect on the total fill level, product size distribution and specific energy consumption, among others. In a complementary way it develops a technical - economical evaluation from industrial data comparing two different ball sizes and its effect on the grinding process analysed integrally."

Jan 1, 2014

By S. Malopheyev, I. Vysotskiy, R. Kaibyshev, S. Mironov

"In this work, the effect of pre-strain rolling on the annealing behavior of friction-stir welded 6061-T6 aluminum alloy was studied. To this end, the as-welded material was rolled to 10 or 20 pct. of thickness reduction prior to the standard post-weld T6 heat treatment. Three rolling directions were the 3-mm thick sheet were considered: along the welding direction, perpendicular to the welding direction, and at the angle of 45° to the welding direction. At relatively low pre-strains (10 pct.), the annealing behavior was found to be very sensitive to the rolling path, and rolling along the welding direction was most effective in suppressing abnormal grain growth. On the other hand, increasing the pre-strains to 20 pct. of thickness reduction inhibited abnormal grain growth irrespective of the rolling path.INTRODUCTION Heat-treatable wrought Al-Mg-Si alloys are widely used due to attractive combination of strength, ductility, excellent corrosion resistance and low cost (Polmear, 2006). To provide the optimal balance of mechanical properties, these materials are typically commercially available in appropriately work- and precipitation-hardened conditions (Polmear, 2006). During conventional fusion welding, however, the prior strengthening effect is totally lost due to elimination of the work hardened structure and dissolution of the strengthening precipitations. An innovative friction-stir welding (FSW) technology may partially overcome this problem. Due to the solid-state character of this process, which involves very large strains, the welded material is characterized by fine-grained microstructure with moderate-to-high dislocation density, and thus the prior work hardening effect may be preserved or even enhanced (Threadgill et al., 2009; Mishra & Ma, 2005). However, heat input associated with FSW inevitably leads to dissolution and/or coarsening of strengthening precipitates, thus giving rise to the undesirable material softening. In an attempt to restore the strength of the friction-stir welded material, the standard T6 post-weld heat treatment has been applied, but this approach was found to lead to abnormal grain growth (Malopheyev et al., 2016; Mironov, 2013, Mironov et al., 2015)."

Jan 1, 2018

By H. P. LeVan

The Bureau of Mines has developed a technically feasible continuous single-stage leaching and thickening system for extracting manganese from umber by a sulfuric acid-ferrous sulfate process; the cocurrent leaching and thickening system proved simpler to operate and control than the countercurrent leaching and thickening system developed earlier" Related tests investigated the use of a centrifuge to replace thickeners for separating the product liquor from are residues and compared several chemical agents for removing iron from the pregnant manganese leach solutions. Results of Some exploratory autoclaving tests are also given.

Jan 1, 1972

By J. M. Dean

The MANpower SUPport Program (MANSUPP), a part of the Mine Management Support System (MMSS), allows an underground coal mine site user to determine manpower requirements for production support work by considering ongoing operations and current mine conditions. The objective of MANSUPP is to plan a detailed manpower structure for a mine by incorporating a production schedule, condition-modified work standards and management preferences to predict required manhours for various activities, for example, belt moves. The program is written in Quattro Pro version 3.0 (Lotus 1-2-3 compatible) utilizing the command language, macro and formula capabilities.

Jan 1, 1992

By Frederick A. Subosits

The Lithium Corporation of America's Hallman-Beam spodumene-pegmatite open pit mine is located in the Kings Mountain area of North Carolina. Figure 1. Presently this area of North Carolina is the lithium center of the U.S., if not of the whole world. The Lithium Corporation mine was started in 1968 and now covers 61,000m2 (15 acres) with projected are reserves in excess of 20 years. Lithium occurs at the Hallman-Beam property in a mineral known as spodumene (LiAlSi2O6), a lithium aluminum silicate. The run-of-mine are averages 1.43 Li2O. Figure 2 of the general Mining Division flow sheet follows the concentration of the Li2O to 5.5% and also lists the various by-products that are sold commercially. The unique properties of lithium have led to many commercial applications, some of these including lubricating greases, ceramics, glasses, glazes, welding fluxes, aluminum reduction cells, dehumidifying and air-conditioning equipment, sanitizers, polymerization catalysts, batteries, and pharmaceuticals. (3) (5)

Jan 1, 1978

By Shaohua Ju

Siderite ore is abundant around the world, due to its inert properties of low grade, mudding when milling and low magnetic, and it is very hard to be beneficiated. Nowadays, decomposition by roasting becomes the main process for utilization of the siderite ore. The methods of energy input for roasting are normally electrical heating, coal or gas combustion. Because traditional roasting methods owns some disadvantiges, such as low energy utilization, high cost and/or large exhaust pollution, only about 10% of the siderite ores in China were used as iron concentrate. In this work, the possibility of roasting siderite ore with microwave energy is studied by both laboratory and pilot experiments. The result of laboratory experiments showed that the optimized condition is roasting for 20 min with a power density of 3 W/g, and the Fe content of the final sample obtained is about 59.12%. The pilot experiments result showed that the decomposition is thoroughly, and the main phases of the roasted material are magnetite and wustite, and the energy consumption of the roasting process is 695.8 KWh/t.

Jan 1, 2014

By H. B. Pulsifer

THIS paper outlines a method for rapid production of flat, granular surfaces on many of the medium hard- alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a. rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesium which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples -formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have -been used to good advantage for the purpose. However, if they are expected to etch rather deeply-that is, smooth as well as characterize-the results may be far from satisfactory.

Jan 1, 1928

By Zhang Libo, Li Wei, Peng Jinhui, Guo Shenghui, L. Jing

Partially stabilized zirconia ceramics (PSZ) were prepared by microwave sintering using natural baddeleyite which was obtained by flotation of baddeleyite ore as starting materials. Because of using natural baddeleyite as raw and the process producing no waste, it realized shorter process, energy savmg, environmentally-friendly and non-damage processing. In this work natural baddeleyite stabilized with 3.8wt.% CaO were sintered at 1300°C for 60min in a multi-mode 2.45GHz microwave furnace. Microwave sintering could fast heating and sintering. Besides that, microwave sintering could heat materials wholly, low the sintering temperature, improve the materials properties and save energy. X-ray spectrum displayed the product composed by the tetragonal phase and monoclinic phase that also showed the product was PSZ. Fine and uniform microstructures were observed in the product through scanning electron microscopy. PSZ which was with high density was confirmed by the method of the Archimedes technique.

Jan 1, 2011