Search Documents

By Richard C. Newell

The United Kingdom marine aggregate mining industry is the second largest of its kind after Japan. Materials for the construction industry, sea defences and for many other purposes are exploited from shelf waters at depths of 30-50 metres by self-contained suction dredgers which often screen material to obtain a cargo of a particular quality. Assessment of the environmental impact of such mining activities both within the boundaries of the dredged areas, and in the zone of deposition of outwash from the dredger has in the past been mainly based on predictive models based on the settlement rates of the individual particles and assumed Gaussian diffusion principles during the settlement phase. Recent studies which we have made on both the mass balance for materials rejected during the dredging process and direct measurements of the settlement of material in the dispersing plume suggest that the zone of settlement is much less than that predicted from diffusion models. Instead of a downstream settlement plume of 10-20 km in the tidal currents of U.K waters, our measurements show that inorganic components of the dredger plume reach background levels in the water column within 880 metres.

Jan 1, 2000

By Wm. Reisz

There is no universal standard for Standard Operating Procedures (SOP’s). Every blasting operation has its own unique circumstances, its own methodologies and its own unique demands. It would be nearly impossible to create a one-size-fits-all document that would be totally appropriate for every blasting scenario. But there are universal objectives that should be adopted in any set of blasting SOP’s.

Jan 1, 2010

The Mt Whaleback open cut mine South Wall is, in part, developed as an unbenched dip slope. The remainder of the rock slope consists of asymetrical overturned folds which have been locally truncated by major low angle faults. The Mt Whaleback orebody is structurally controlled and therefore extensive structural geology input has gone into the final rock slope design. The design is based on normalised 40 m geological cross sections, but the inherent complexity of the geological structure of the orebody yields a high degree of uncertainty within that interval. There- fore, the final slope bench face and the penultimate bench faces are mapped in detail to accurately establish the geological contacts and struc- ture. The knowledge of accurate geology of final and penultimate faces plays a very important role in the design of controlled perimeter blast- ing. Accurate geology is established mainly by face mapping, and by hole geological evaluation of blastholes to locally refine the current Geologi- cal model.

Jan 1, 1989

By Earl Bardwell

(Butte Meeting, August, 1913.) THE structural relations existing between cuprous oxide and copper were first systematically studied by Heyn1, who suggested that a study of the microstructure of refined copper might be substituted for the analytical methods in vogue for determining the oxygen content of copper coming .;from the refining furnace. Hofman, Green and Yerxa,2 in their paper A Laboratory Study of the Stages in the Refining of Copper, working along the lines suggested by Heyn, showed that a study off the microstructure could be made to yield a correct estimate of the oxygen content of the specimen of refined copper under examination. In order to determine the oxygen content of the specimen of refined copper under examination a photomicrograph was first made. From the relative areas of copper and eutectic, the percentage of cuprous oxide and the corresponding percentage of oxygen were then readily calculated. It was found that the values for oxygen thus obtained corresponded closely with the analytical results. With the idea of utilizing, this method of determining the oxygen content of each charge dipped from the refining furnaces at the Boston & Montana Reduction Plant, the physical testing laboratory was equipped with suitable apparatus for carrying out the work. It may be of interest to describe certain of the methods which have been worked out in, this connection and give such data as have been obtained bearing on the effect of the oxygen content of refined copper upon its conductivity.

Jan 7, 1913

By H. Maleki

Interwest Mining Company has been collecting geologic data within the last decade in preparation for underground mining of extensive coal reserves in its Bridger Coal property in southwestern Wyoming. During a preliminary data collection program in 2000, Interwest Mining completed geologic investigations, including surface mapping, drilling, aerial photography, rock testing, and limited groundwater investigations. Core from 12 exploration boreholes in the area of interest was tested to determine the mechanical properties of the coal seam and the immediate roof and floor for evaluation of the feasibility of underground mining. Geologic investigations identified the presence of one 7-to-17-ft-thick coal seam throughout the reserve under 1400 ft of cover. During a geotechnical feasibility study in 2002, the authors reviewed available data while completing comparative analyses identifying critical deficiencies in these data. The study projected moderate-to-difficult mining conditions, considering the weak nature of near-seam strata and depth of cover, and thus recommended limiting the longwall reserves to an overburden depth of less than 900 ft. These shallow remaining reserves were located at depths within regional mining experience to justify longwall mining methods. Based on a critical examination of available data, Bridger proceeded with more detailed data collection to improve understanding of the depositional and structural setting of the reserve, hydrogeologic conditions, overburden strength, and premining stress conditions. Additional data was collected during 2003 and 2004 field programs. Since 2003, Bridger has had the opportunity to observe ground behavior in a series of up to 1200-1600-ft- long rectangular openings created during highwall mining. These narrow unsupported openings remained stable in the short term in large areas but the overburden subsided locally in the long-term depending on geologic and panel layout designs. These localized subsidence events allowed an examination of in-situ coal strength based on back analyses of stress. The unextracted highwall areas near Ramp 17 provided an ideal location to access the underground reserves using a 6-entry set of mains. The existing north-south oriented longwall layout for the Bridger Coal was selected by Bridger to maximize resource recovery from the D41 reserves while considering operational and geotechnical constraints. At 45-degrees deviation from preexisting joints and mild horizontal stress field, this orientation was considered beneficial for overall stability while using both sets of joints for facilitating the caving process. The present layout utilizes pillars on 80- to 90- by 200-ft centers, 17-ft entry spans and 750-ft wide longwall panels (Figure 1). Gate pillars are on wide spacings and are intended to act as abutment-abutment pillars to limit strata deformation over the gateroads during longwall mining.

Jan 1, 2008

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By Alexander R. Troiano, Eugene P. Klier

Since the very early work on quenched structures, where the products of the martensite transformation had been recognizedl this transformation has provoked much interest and study. Theoretically it was desirable to account for the extreme changes in physical properties resulting from the formation of martensite, as that information might lead to results of practical importance. Desirable information, therefore, was on the kinetics of transformation from austenite to martensite as well as on the physical constitution of the martensite. It has been known for years that certain steels quenched to room temperature will contain persistent austenite as well as martensite. Other important and now well-established features of the martensite reaction are the Progress of the reaction on cooling only and the independence of Ar" with cooling velocities exceeding the critical velocity. These facts have been experimentally determined by various methods and investigators. Notable among the early investigators were Tammann and Scheill and Wever and Engel.2 Unfor- tunately, all investigators did not fully interpret their results, which, coupled with several investigations that yielde. conflicting resultsl caused a state of confusion that was not clarified until quite recently. X-ray investigations of martensite in steels3-6 indicate it to be a supersaturated solid solution of carbon in alpha iron. This supersaturation is evident from the appearance of a body-centered tetragonal structure with the addition of sufficient carbon. The dimensions of this tetragonal structure are a linear function of the carbon content within the limits of accuracy of the determinations. Slight tempering of tetragonal martensite leads to the destructi,, of the tetragonal structure, which is converted to a body-centered cubic strutture. This phenomenon has precipitated a controversy concerning the nature and mechanism of the tempering of martensite The facts in the case have been outlined by Epstein7 and more recently by Antia, Fletcher, and Cohen.8 The significance of Ar" on theoretical grounds is not clear, however, although considerable study has been devoted to its determination. The precise position of Art' aS a function of carbon content was first stated by Greninger and Troiano9 for steels covering a range of approximately 0.7 to 1.8 per cent carbon. The effect of alloying elements on Ar" has recently been the subject matter of investigation by various methods.

Jan 1, 1945

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By J F. Colinet, G, J A. Zimmer, R J. Timko

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/non-metal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 per cent throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurisation systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a workerÆs clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2005

By H. E. Powell

A series of alkyl-dithiocarbamic acid amine salts was prepared and tested as collector for slimed lead minerals contained in the waste material from a commercial lead ore concentrator. The reagents, members of a homologous series differing only in the number of alkyl radicals in their structure, were prepared by reacting stoichiometric amounts of primary amines and carbon disulfide in a cold alcohol solution. Subsequent purification was by recrystallization from absolute ethyl alcohol solution. Evaluation was through froth flotation of a mill tailing containing 0.2 percent lead. Results show that maximum recovery (38 percent) was obtained with the reagent containing 8 alkyl radicals, but that maximum rougher concentrate grade (4.8 percent) was obtained with the reagents of intermediate number of radicals.

Jan 1, 1962

By J. N. Roberts, K. V. Gow

In a recent review of the field of plastic deforrnation of metal single crystals, Maddin and chenl indicated the need for systematic investigations of the crystallography of the slip process with special attention to: a) The effect of the orientation of a crystal on the appearance of slip lines, b) The effect of high temperatures on the slip systems of aluminum, c) The effect of strain rate on the crystallography of slip. The present paper deals with the effect of temperature and strain rate on the mechanism of deformation of aluminum single crystals similarly oriented for single and duplex slip. The work of several investigators has shown that in aluminum at high temperatures other slip systems in addition to the predicted {I l l) <101> may operate. The most generally reported additional systems

Jan 1, 1959

By E. L. Jr. Spain

THE deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of Mississippi and Alabama respec-tively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewell1 and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance.

Jan 1, 1936

By W. M. Lewis

Product losses to tailings ponds have long been a source of frustration for the mining and utilities industries. The utilization -of the Lewis Econosizer to recover lost products has proven to be very cost effective through reduced acreage requirements, cleaning costs and increased production. The unit is successfully operating in coal, aggregates, industrial minerals, clay, fly ash, heavy minerals and many other ores. Utilizing an upward flow of slurry in a free settling environment, particles stratify within the unit according to settling velocities and are removed as sized products. Ultra fines or clarified water is removed off the top of the unit. The Econosizer requires no power and only minimal maintenance.

Jan 1, 1998

By G. S. Rice, R. V. Wheeler

"FOREWORDThe cooperative mine safety research program was carried on successfully in the year 1930 in a manner similar to that described in the report for 1929It is believed that the results of such fundamental work as is being done are unquestionably of great benefit in their application in coal-mining operations, in the saving of life and health of minera. The research result compared and checked by investigations in the two organizations, and further by large-scale tests, as in the Experimental Mine, give confidence to mine operators, miners and State mining officials in the findings of the various researches.The annual report of the contact officers of the United. States Bureau of Mines and the British Safety in Mines Research Board to the Director of the Bureau and the Chairman of the Board respectively, follows:Annual Reports for 1930 To: The Director, Bureau of Mines.The Chairman, Safety in Mines Research Board."

Sep 1, 1931

By Edgar M. Dunn

Part I. Determination oF Gases in Smelter Flues. General considerations. Regular methods for carbon monoxide, oxygen, nitrogen, moisture. Sulphur oxides-—Methods of Lunge and Hempel tried, and either modified or discarded, with reasons therefor. Gravimetric method developed at Anaconda. Description of apparatus used. Brief notes on Richter and Hawley methods for the direct cietermination of sulphur trioxide. Carbon dioxide, with complete notes on same. Arsenic trioxide. Table of percentages of flue gas constituents found at a Western smelter. Some final notations as to the value of flue gas analysis, in connection with an intelligent log of furnace operations. Part II. Notes on the Determination oF Dust Losses at the Washoe Reduction Works, Anaconda, Mont. Discussion of problem, with description of flue system. Various places and methods for determinations of velocity. Instruments used. Procedure in making determinations for velocity. Soundings of cross-section for depths of dust. Calculation of velocities and areas. Daily volume of gas, and plant operations during tests. Place for dust determinations. Apparatus and methods of &apos;sampling. Results obtained, with table of daily amount of dust losses. Analysis of dusts for values, from various sampling stations. Complete analysis of composite sample of stack emanation. Last analysis totaled to show form in which present. Discussion of recovery as a commercial proposition. References on Pitot tube and calculations.

Jan 1, 1914

By Just GD, Gillies ADS

There is an increasing need for reliable and comparable coal resource data and it is necessary to standardize the traditional classification procedures by quantifying the three basic evaluation criteria of economic feasibility, geologic assurance and recovery. For well documented deposits, geostatistical methods can consider- ably improve classification quality. A geostatistically based algorithm for classifying coal resources within the current Queensland and New South Wales codes has been developed. Application of the method in classifying resources from a number of seams exhibiting different structural characteristics is assessed. The method is found to give classification results which closely reflect the error associated with an estimate of resource quantities based on current sampling densi- ties. It requires a careful geostatistical analysis with emphasis on geological awareness. Resource category restrictions must be arbi- trarily assigned and remain constant for all deposits being compared. Engineering judgement is needed and interpretation may be required with isolated and peripheral blocks.

Jan 1, 1987

By Hare S. M, Lumsdaine I, O&apos

Converter slag assaying 3.7 per cent Cu is produced by Mount Isa copper smelter at a rate of up to 180 000 tonnes per annum.Priority is given to the processing of ore, however concentrator capacity periodically exceeds that of the mine and the opportunity is taken to treat converter slag. It is processed in batch campaigns, typically through the Copper Concentrator, but the Hilton Concentrator has also been used. Slag and ore are kept as separate as possible, since each has an adverse effect on the flotation performance of the other.

Jan 1, 1993

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to devise a procedure for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 parts per million of W03). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten was recovered as a marketable iron-tungsten concentrate containing 44 percent tungstic oxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process-development unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By J. E. Udd, L. B. Geller

"Mine-shaft wire-rope discard regulations include, among other criteria, a limited amount of permissible loss-of-breaking-strength (LBS). Currently, this parameter is estimated on the basis of non-destrutive-testing (NDT) with electro-magnetic (EM) type instruments. This paper analyses the accuracy with which these estimates have, so far, been obtained in practice.It concludes that while certain types of testers have produced better results than others, the desired accuracy level has not been attained. Also discussed are the putative reasons for this situation, and appropriate actions that the mining industry might wish to take."

Jan 1, 1990

By F. Twyman, D. M. Smith

THOSE chemists (they are still greatly in the minority) who use the spectroscope, use it very often, and find it almost indispensable. As a means of detecting minute quantities of the metals it is unrivalled. A metal can be readily distinguished in the presence of any other element, compound, or mixture without the necessity of separation. The qualitative analysis of the metallic constituents of a substance, which the spectroscope gives so easily, is a sure basis for planning a chemical analysis. As the determination of each element proceeds the purity of precipitates may be checked as often as desired. If, possessing these advantages, the spectroscope has been neglected in general chemistry, it is not surprising that it was neglected in metallurgical chemistry; for many of the impurities which are of industrial interest, even when they are present in a metal or alloy in small quantities, are not then always easily detected by the examination of their visible spectrum. The history of the development of the art has been given in Bureau of Standards Scientific Paper No. 444.

Jan 1, 1928