Search Documents

By W. Tse, D. Wong

Dense medium separation (DMS) is one of several preconcentration methods used for early waste rejection from run of mine ores at relatively coarse particle sizes prior to additional milling and beneficiation. DMS has been used extensively in the coal, diamond and iron ore industries but lab scale and pilot test work has demonstrated successful separation and upgrading of other minerals such as lead, zinc, copper and lithium based ores using DMS. This paper reviews historical dense media systems, results from the pilot scale Condor DMS system as well as associated laboratory heavy liquid separation (HLS) test work.

Jan 1, 2014

By Peter A. Cain, John C. Folinsbee

"A 4-ft.-diameter shaft has been drilled to a depth of 2,790 ft. in strong, hard, basic Precambrian rocks at Lynn Lake Manitoba. This was done on the property of Sherritt Gordon Mines Limited for the purpose of ventilating and developing the ""N"" orebody, which is located approximately 4,000 ft. south of the Farley shaft.The drilling was done under contract by two drilling companies. Peter Bawden Drilling (1964) Limited drilled the initial 12:1,4-in. pilot hole to a depth of 3,000 ft. Shaft Drillers Limited of Canada then reamed the hole to 4 ft. in diameter to a depth of 2,790 ft. At this point, the reaming was stopped because of the difficulty in passing a change in direction in the line of the pilot hole. The hole was completed by driving a raise 200 ft. from the 3000 level to the bottom of the 4-ft. hole using an Alimak raise climber.Cuttings from the reaming operation were directed into the 12:1,4-in. pilot hole, where they fell to the 3000 level and were removed by a mucking machine and standard mine development cars.The elapsed time from the start of the pilot hole to the completion of the reaming operation was ten months, with an average advance of 279ft. per month. There was a two-month delay between the completion of the pilot hole and the start of the reaming operation.The 12:1,4-in. hole was drilled in an elapsed time of 45 days from the time of setting up the rig. The average advance per day was 66.8 ft.The reaming operation was done in an elapsed time of 194 days. A one-month delay required to repair damaged equipment left 163 days for the drilling and setting-up operation, for an advance per day of 17.1 ft."

Jan 1, 1966

By A. E. Isaacson

The U.S. Bureau of Mines is investigating a systems approach to metals recovery from leach liquors produced by in situ leach mining techniques. A successful in situ leaching process requires a thorough under-standing of the complex interrelationships that exist between leaching chemistry and metals recovery. Laboratory research is addressing these interrelationships in the solution mining of a copper oxide deposit. Laboratory tests have been conducted to gather baseline data related to the design and operation of continuous leaching-solvent extraction-electrowinning circuits. This paper addresses the findings of the baseline studies. Specific results include the characterization of simulated in situ leach liquors produced by leaching chrysocolla and chrysocolla-atacamite-bearing copper ores. Metal recovery procedures, utilizing four commercial solvent extraction reagents, are also characterized, and potentially troublesome leach liquor contaminants that may complicate waste management procedures are identified.

Jan 1, 1990

By Daniel E. Sullivan

The recession of 1974 continued into 1975. Real gross national product (GNP), measured in 1972 dollars, declined significantly in the first quarter of 1975 but rose slightly in the second and increased sharply in the third quarter. Unemployment peaked during the second quarter and then declined slowly for the balance of the year. The inflation rate declined owing to reduced demand and smaller-than-1974 increases in energy and food prices early in the year. Recovery was clearly evident by yearend, though un-employment and inflation remained at high levels. Total output as measured by the GNP in current dollars rose 6.5% in 1975. Real GNP declined 2.0%, and inflation, as measured by the implicit price deflator, increased 8.7%. Real gross private domestic investment for residential structures declined 18.1% in 1975, which was a smaller rate of decrease than the 27% decline in 1974. Real State and local Government purchases increased 2.4%, and real personal consumption expenditures for services rose 1. 7 %. The Federal Reserve Board (FRB) index of industrial production declined 9.7%.

Jan 1, 1977

By H. J. Roorda

With an increasing need to obtain metals by processing complex fine intergrown ores, the use of electron-optical techniques will become more important as a tool for mineralogical studies. Electron images enable a higher spacial resolution than can be obtained by optical microscopy and thus provide a powerful and necessary aid for the examination of small grains and finely locked particles. In this paper the mineralogy of Meggen ore was investigated. Both light-optical and electron-optical techniques were used to evaluate the mill feed and products of the concentrator. Detailed examination by reflected-light microscopy to assess the comportment of galena in the complex pyritic ore was inconclusive in establishing the cause for low lead recovery of only forty percent of the ore's lead content. Electron microprobe analyses indicated that the majority of the lead lost to the tailings was accounted for by extreme fine (often smaller than one micron) and complex intergrowths of galena in pyrite. The remainder was lost as fine free galena grains.

Jan 1, 1987

By D. M. Hausen

The term "auriferous pyrite" relates to an association of gold with pyrite in a variety of textural forms that affect metallurgical treatment. Extraction of the gold depends not only on the grain size and distribution of the gold in the pyrite, but also on the crystal size and surface area of the pyrite. Occlusions of medium to coarse gold may be liberated by moderately fine grinding. The amenability of finely dispersed (submicroscopic) gold depends in part on the activity of the pyrite surface for oxidation. Two types of auriferous pyrite at Carlin, Nevada, have been examined by optical microscopy and SEM methods before and after aqueous oxidation test work to show how differences in morphological features can affect rates of oxidation and amenability to gold extractions by methods of chlorination and low temperature oxidation.

Jan 1, 1981

By D Kavanagh, C Michaud

"A continuous improvement initiative was identified at Kalgoorlie Consolidated Gold Mine’s (KCGM) Fimiston open pit with the goal of reducing bench turnover time and increasing shovel digability by improving fragmentation around previously mined-out stopes. In the past, a higher number of blasts than normal would be required to get through a single excavation area where stopes were present. This is due to the limited reach capability of the drilling fleet from safe ground into restricted areas requiring the drilling of the shot to be done in a staged manner. In addition, the holes that were able to be drilled in the area did not remain open long enough to be loaded with explosives as a result of the poor ground conditions surrounding the stopes.Over the last 18 months, KCGM has trialled drill additives to improve blasthole stability, as well as introducing a remote drill rig allowing holes to be drilled in areas previously inaccessible by manned drill rigs. This has resulted in improved penetration rates in bad ground conditions, improved drill hole stability, better shovel digability, and an overall reduction in bench turnover of at least ten days on the benchmarked 126 days average per bench. KCGM is now in the final stages of the improvement project with the installation of a drill monitoring system on the fleet to allow live data transfer back to the office for analysis, as well as providing improved accuracy on drill holes in restricted areas.Citation:Michaud, C and Kavanagh, D, 2016. Reducing Bench Turnover Time and Improving Shovel Digability, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 19–27 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By D Engelhardt, G Lane

The Cadia mine has shifted from an open pit operation to the Cadia East underground panel cave. The resulting increase in milled tonnes, more competent ore and the decrease in fines production through shifting to panel caving were predicted to require an increase of over 25 per cent in installed power. This expansion was accomplished via the installation of secondary and high pressure grinding rolls (HPGR) crushing of the ore, with the semi-autogenous grinding (SAG) mill receiving a combination of primary, secondary and HPGR crushed feed. This design, criteria and rationale for selection was presented at the SAG Conference 2011. This paper reports on the initial impact of secondary and HPGR crushing on the circuit performance with the new panel cave feed.CITATION:Engelhardt, D, Lane, G and Powell, M S, 2014. Cadia expansion – the impact of installing high pressure grinding rolls prior to a semi-autogenous grinding mill, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 233–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Seth C. Scharfer

"As part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology, the Gibbs energies of formation of MoS2 (molybdenite) and WS2 (tungsten disulfide) were determined with high-temperature galvanic cells employing stabilized Zr02 (zirconia) as the electro¬lyte. In the temperature range from 867 to 1,209 K, potential measurements were obtained for the cellPt, MoS2 , Mo02 , SO2 = 1 atm // Zr02 // 02 = 0.0112 atm, Pt, with the overall cell reactionMoS2(c) + 3 02(g, 0.0112 atm) = Mo02 (c) + 2 S02(g). (1)These results, combined with the best available values for Gibbs energies of formation (?G°f) of Mo02 (molybdenum dioxide) and SO2 (sulfur dioxide) from the literature, give the standard Gibbs energy of formation of MoS2, ?G°f, for the reactionMo(c) + S2(g) = MoS2(c) (2)?G°f = -96.681 + 43.76 x 10-3T±0.538 kcal/mole, (3)where temperature (T) is expressed in Kelvins.Similar measurements in the temperature range from 872 to 1,210 K were obtained for the cellPt, WS2 , W03 , SO2 = 1 atm // Zr02 // 02 = 0.0114 atm, Pt, with the overall cell reactionWS2(c) + 3.5 02(g, 0.0114 atm) = W03 (c)+ 2 S02(g). (4) Combination of these results with the best available data of ?G°f for W03 (tungsten trioxide) and SO2 from the literature gives the Gibbs energy of formation of WS2 in the temperature range from 872 to 1,210 K for the reactionW(c) + S2(g) = WS2 (c)(5)?G°f = -92.429 + 43.88 x 10-3T ± 0.280 kcal/mole. (6)A third-law analysis yields a standard enthalpy (?H°f) for the reaction298Mo(c) + 2 S(rh) = MoS2(c), (7)?H°f = -67.36±0.60 kcal/mole, (8)298where the standard states are pure crystalline MoS2 / and rhombic sulfur."

Jan 1, 1980

By Y Li, Z Fu, D J. Williams, E Topal

Mine waste rock is unavoidable in the recovery of ore by open pit mining methods. Effective management of waste rock movement covers the removal and placement of the waste rock, generally in a surface dump in the most cost-effective way while satisfying the long-term environmental expectations. Since the 1960s, there has been significant research carried out into planning of ore movement from open pit mines such that the overall net present value (NPV) of the project can be maximised. Currently, several software packages are available to achieve this task as a common practice within the mining industry. However, planning of mine waste rock movement is still achieved manually, as the available software does not consider optimal waste rock movement and dump design. This paper describes a tool to optimise waste rock placement, which minimises the haulage cost while creating environmentally friendly waste rock dumps through selective placement and encapsulation of the reactive waste rock in the dump. The embedded methodology in this tool has been developed based on the mixed integer programming (MIP) modelling technique to optimise the waste rock movement. The methodology provides an easily-manipulated and fully-automatic tool for professionals to complete waste rock dump scheduling in four main steps: data input, model construction, model computation and solution retrieval. The application of the new tool into a real case project in this paper shows that it can determine economically and environmentally optimised waste rock dump schedules in an acceptable time frame.CITATION:Fu, Z, Li, Y, Topal, E and Williams, D J, 2015. A new tool for optimisation of mine waste management in potential acid forming conditions, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 333–342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Tung Vu, Michael Harrington

"The Regional Connector project is a complex subway light-rail project that runs through the heart of downtown Los Angeles, CA. The design-build contract was awarded in April 2014 to the Regional Connector Constructors (RCC), a joint venture between Skanska USA Civil West California District Inc. and Traylor Brothers Inc., and their designer team consisting of Hatch Mott McDonald (HMM) and subconsultants. The project broke ground on Sept. 30, 2014 and is expected to be completed in winter 2021-2022. The main components of the project consist of 6.4-m (21-ft) diameter twin-bored tunnels, three crosspassages, a 87-m (287-ft) long crossover SEM cavern, three new underground stations, and cut-and-cover tunnels along South Flower, Alameda and 1st Streets. The project map is shown in Fig. 1. The design and construction challenges associated with each of these main components are discussed in the following sections.Project designTunnels. The Regional Connector tunnels are located primarily within the Fernando formation consisting predominantly of extremely weak to very weak, massive, clayey siltstone. About 305 m (1,000 ft) of tunnels on the eastern end are in alluvium and mixed face of Fernando formation and alluvium. The tightest curve of the tunnel alignment is 178 m (583 ft) in radius. The tunnels were designed with a reinforced precast concrete tunnel lining (PCTL) to be used with an earth balance pressurized (EPB) tunnel boring machine. The PCTL ring is 5.5 m (18 ft-10 in.) inside diameter, 27 cm (10.5 ft) thick, 1.5 m (5 ft) long, and consists of five segments and a key. The segments were designed with 6,500 psi concrete, 80 ksi yield strength wire rebar, convex joint surfaces to enhance seismic performance, and a dosage of 1.7 lbs polypropylene microfibers per cubic yard of concrete for fire resistance. The rings are designed with a right ring and left ring pattern and a taper of 3.8 cm (1.5 ft) to allow for alignment curve negotiation. Figure 2 shows typical sections of the PCTL. The structural lining design was modeled using FLAC 3D. Four consecutive rings were modeled with 32 dowel connection. Loading considered in the lining design includes temporary ground load during excavation, long-term ground loads, seismic loads and train loads. The seismic loads on the PCTL were simulated with the racking deformation applied at vertical boundaries of the model. Due to variation of geologic condition along the tunnel alignment and different surcharge requirements, three different types of reinforcement (typical, heavy and extra heavy) were designed. The typical type PCTL was required in Fernando formation, the heavy type was required in alluvium or mixed-face condition, and the extra heavy type was required in alluvium and underneath the Japanese Village Plaza where a surcharge of 1,000 psf was required."

Sep 1, 2019

By Takeshi Nagano

"Prior to discussing future trends of non-ferrous metals smelting and refining, the past developments are looked back. Social and economic environments in Japan over the past two decades are reviewed. Technological developments to comply with these environments are explained, taking for examples the cases of the Mitsubishi continuous smelting and converting process and Onahama's jumbo tank system for copper tankhouse. After considering the factors which will influence the improvements in non-ferrous processing, future trends are forecasted generally for copper, zinc, lead, aluminum and rare earth metals. Recent development works in Japan for the future are also introduced. In the discussed area, it appears that the emergence of new innovative processes would be difficult. The progress will be made rather toward the sophistication of the existing technologies, utilizing the advancement of the related technologies such as computers, electronics, etc. IntroductionThis paper discusses the future trends of non-ferrous metals smelting and refining on the occasion of the international symposium, ""The Metallurgical Processes for the Year 2000 and Beyond"".It is considered that the improvement of technology is greatly influenced by the social and economic environments which surround it. From this standpoint, review was made of Japanese case over the past two decades. Various new technologies were developed also in the non-ferrous metal world to comply with the requirements under the above environments. The examples are described in the cases of the Mitsubishi continuous smelting and converting process and Onahama's jumbo tank system for copper electro-refining.After foreseeing the major factors which will affect the technological developments in the future, the trends are forecasted for copper, zinc, lead, aluminum and rare earth metals generally. Some development works in Japan, which will give suggestions for future trends, are also introduced in some detail."

Jan 1, 1988

By G. F. MacDonnell

THE Privateer mine consists of a group of mineral claims situated in the Zeballos area, on the west coast of Vancouver island, approximately 180 miles north of Victoria. Although Zeballos is a comparatively new mining camp, its transportation facilities can be considered exceptionally good. General freight and supplies are brought in by either C.P.R. or Frank Waterhouse steamers from either Victoria or Vancouver. Service by these boats varies from five to ten days and the trip from Victoria takes approximately two days. Passengers may use the C.P.R. boats, or, if speed is essential, they may fly, in which case they have the choice of two flying companies, namely, Canadian Air-ways, Limited, and Ginger Coote Airways. The average flight from Vancouver takes approximately two hours. Excellent unloading facilities are provided at the beach by a government dock for the steamers and a floating dock for aeroplanes. The mine, which is approximately five miles from the beach, is serviced by a fairly good gravel road, which has proved satisfactory for all haulage purposes. Zeballos has the reputation of having one of the heaviest rainfalls on the west coast, but as no accurate records have been kept, no comparisons can be made. H. C. Gunning, in his report, comments on the weather from 1929 to 1932, and one would judge that the practically continuous rainfall did not add to the pleasures of the field work. During the summer of 1938, the opposite condition prevailed and the area had exceptionally dry and pleasant weather. The snowfall is generally light at the lower elevations, but very heavy higher up. No extreme cold weather is encountered during the winter, which is generally short.

Jan 1, 1939

By H. Sis

The pressure filtration behavior of dispersed and flocculated alumina slurries at high percent loadings is discussed with an objective to determine the effect of surfactant type and concentration on slurry properties. A high purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by surfactants that are considered to act by electric and steric stabilizers. The effect of both the ionic and nonionic surfactants was investigated. Surface charge measurements of the slurries were carried out by electrokinetic sonic amplitude (ESA) method to understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and final cake properties are discussed.

Jan 1, 1998

By C. G. Anderson

The treatment of concentrates for the recovery of the precious metals imposes many processing and environmental challenges. Hydrometallurgical technology for recovery of values from refractory precious metal materials has been developed at Sunshine Mining and Refining Company. Historically, conventional pyrometallurgical methods have been used for to recover values from refractory precious metal materials. However, enhanced environmental awareness has worked to constrain typical refractory material processing methods. This hinders and limits the ability of established smelting or roasting technologies to fill the needs of new sources of refractory materials. An alternative is to treat refractory precious metal bearing materials by hydro metallurgical techniques. These methods are considered more environmentally appropriate since they do not produce gaseous pollutants like sulfur dioxide. Industrially, Sunshine Mining and Refining Company employs hydrometallurgical technology to process refractory precious metal materials. The Sunshine antimony leach uses a mixture of sulfur and caustic under ambient pressure and boiling conditions. The Sunshine oxidation leach uses a mixture of sulfuric acid and a minimal amount of sodium nitrite under relatively mild oxygen pressure and temperature conditions. These conditions result in a nitrogen species catalyzed sulfuric acid pressure leach. Since hydrometallurgical technologies provide industrially proven processing options for many types of refractory precious metal containing materials, their usage should be considered. Ample work has been conducted to prove the effectiveness of Sunshine refractory processing technologies on various materials. This has included platinum group metal materials, refractory gold concentrates, silver materials and indium materials. In some cases, complete process flowsheets have been designed to recover both base and precious metals from these materials and to treat the generated waste streams in environmentally sound manners.

Jan 1, 1996

By A. L. Mular

Some specific cases of the collection of data from industrial grinding and classifying operations, and the development of models from the data so obtained, will be described. The problems encountered, the effort involved, and the value of the derived models in improving the plant efficiencies will be discussed and documented where possible.

Jan 1, 1971

By R. DasGupta

The dissolution behavior of gold in ammoniacal solutions at 75°C has been investigated. The variables investigated include concentration of lixiviants, pH of the solution and various oxidants. The anodic dissolution of gold was studied in the absence of oxidants using the potentiodynamic polarization technique. The cathodic reaction of oxidants was studied on a platinum electrode. Tafel polarization tests were also performed to determine the dissolution rate. The overall dissolution of gold in ammoniacal solutions was examined using a mixed potential theory. A comparative study on the role of cupric am mine, oxygen, hydrogen peroxide, sodium hypochlorite as oxidants for the dissolution of gold in ammoniacal solutions has been carried out.

Jan 1, 1996

By John C. Robbins

A new technique for the determination of trace levels of uranium in solution has been developed. A compact laser emits short, but intense, ultraviolet pulses to excite the green fluorescence of a uranyl-complex formed by the addition of a proprietary reagent to the sample. Organic species present in most natural waters also fluoresce quite intensely, but their emission does not last appreciably longer than the excitation pulse, in contrast to the relatively long persistence of the uranyl fluorescence . Electronic 'gating' is employed to separate the long-lived contribution, rejecting substantially the organic emission. Results using the laser fluorescence method on many sets of natural waters of various origins have been compared against corresponding values generated by independent laboratories. Correlation has been generally good over a range from less than 0.1 to more than 100 ppb U. Solid samples have also been analyzed after extraction of the uranium into solution. Accuracies adequate for most exploration purposes have been achieved, but further work is required to determine effects of interferences in samples with complex matrices. The transport and deposition of uranium in natural waters is controlled by the organic and inorganic chemistry of the waters involved. It is suggested that interpretation of very low uranium levels will be aided by additional measurements of conductivity and organic content, with subsequent statistical treatment.

Jan 1, 1978

By H. Maleki

This paper recognizes the 100th year of research accomplishments by the mining industry resulting from close cooperation among mining companies, geotechnical consultants and researchers from the former United States Bureau of Mines in stability assessments and development of improved and productive mine designs. The paper provides an overview of dramatic developments in geotechnical instrumentation, and its applications in the U.S. and around the world for enhancing the understanding of ground response to mining-induced changes in stress, resulting in improvements in ground control technologies.

Jan 1, 2010

By Raymond O. Dannenberg

The Bureau of Mines conducted laboratory and full-scale tests to develop a process for improving the flotation characteristics of lime-treated waste water produced by the Kennecott Copper Corp., Magna, UT. Unknown substances in the waste water reduced the flotation efficiency of the metal sulfides. An estimated annual loss of 795,000 lb Cu, 232,000 lb Mo, 5,625 tr oz Ag, and 617 tr oz Au would result from recycling the total flow from the lime treatment plant to the flotation mill in an effort to conserve water and reduce associated expense. The tests indicated that aeration or treatment with activated carbon significantly improved the water quality. The improvements in molybdenum recovery averaged 8 pct for carbon, 11 pet for activated carbon, and 16 pct for combined aeration and activated carbon. The combination of the two processes produced water quality as good as or better than normal feed water.

Jan 1, 2011