Search Documents

By Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average Sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining.

Jan 1, 2010

By Kretschmar. U. H.

Fieldwork in the Meguma of Nova Scotia and Archean equivalents shows that bedding-parallel quartz lode gold veins (LVs) commonly occur at the top of graded elastic sequences. We define a "gold cycle" (GC) by analogy with Bouma turbidites and show that most "shear zones" and "lamprophyres" correspond to the upper pelagic-pelitic (E) division. We describe GCs from Archean Chester Twp, ON; Elmhirst, ON; Bourlamaque, QC; "intrusions" and interpret them as crystal tuffs and tuff-breccias. Extensive early Archean pyroclastic volcanism is implied: the genesis of trondjhemite-tonalite-granodiorite (TTG) rocks must be re-examined. The geopetal nature and asymmetric alteration of LVs indicates genesis from sea-floor hydrothermal vents. Textures suggest that often quartz was deposited as a gel. Vent geometry (fracture, point source or diffuse seep), bottom topography and vent spacing is reflected in wade-thickness plots. GC facing directions survive metamorphism. The Bourlamaque batholith was a flat-lying sheet of quartz-feldspar-hornblende crystal tuff, and isoclinal folding has repeated one or more gold-bearing horizons. Syngenesis clarifies and simplifies LV formation with major implications for models. Exploration becomes more cost-effective. Basin analysis, whole rock geochemistry, ore lens geometry and vent spacing can be used.

Jan 1, 2011

By J. G. Bennett

Coal consumption has increased globally by 57% over the last ten years. Underground mining typically provides coal of the highest calorific value and accounts for the greatest proportion of production. Despite a negative environmental image and indeed impact, this industry appears likely to thrive on the global scale for many years to come. Such mining consumes large amounts of electricity with implications for carbon dioxide emission at power plants and emits substantial quantities of the powerful greenhouse gas methane. In response to this significant carbon footprint, the European Union has funded research to examine the potential for a range of improvement technologies in a project entitled Low Carbon Mine Site Energy Initiatives (LOWCARB). Coal properties related to seams and mines, together with longwall characteristics, provide the basis for research into modelling optimally efficient methane drainage with a view to assisting mining as well as maximising electricity generation at surface and hence oxidation of the methane. Possible systems for the oxidation of very low concentration methane in ventilation air, which contributes the greatest greenhouse gas impact due to the volumes emitted, have been studied and modelled. Simulation and investigation of intelligent optimisation of electricity demand patterns provide the basis for reducing the demand peaks at mines and hence the cost and ultimately the carbon footprint of a mine, while specific investigations have been undertaken into ventilation efficiency at an unusually challenging mine and simulation of mine water pumping in order to develop an innovative method to monitor pumping systems efficiency. For post-mining use, the potential of disused shafts for compressed air energy storage to improve the operation of future electricity grids with high renewable energy penetration by reducing peak generation capacity requirements has been studied. While underground coal mining will always by definition be related to a significant carbon footprint, this paper provides an overview of a set of initiatives that can make a positive environmental impact while controlling costs across a huge global industry.

Aug 1, 2013

By Ben Burger

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha?s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32? x 32? EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By Manuel Gomez

This, report presents correlative data on ash and sulfur forms for Pittsburgh seam coal from Greene County, Pa. Prediction equations were developed for sulfur form distributions and washability characteristics. The equations developed were evaluated with an independent set of exploration core samples. It was demonstrated-that both sulfur distributions and washability characteristic's can be predicted from exploration core data ahead of mining. This information can improve the efficiency of selective mining techniques for the production of a uniform metallurgical coal product.

Jan 1, 1967

By J Geronimo, P Kumar, Z Yussupova, M Yahyaei, M Powell

This work goes beyond the general perception of how the well-known mine to mill process can be applied, by applying deeper knowledge along the mining chain. Grade deportment and dilution are considered at the mining stage, and modelled with the new SMI blast movement simulator, linking with the block model data. Assessing the shift to a considerably more competent section of the orebody is quantified via substantial milling trials at standard and higher-intensity blasts. These were stockpiled for batch processing through the mill to ensure feed integrity. The trial work included operating the mill at widely different fillings to develop Grindcurve milling responses. Additionally, model informed process control is initiated via a mill prediction tool.It has been found that accounting for blast movement for the higher intensity blasts could generate additional value of around $1.5M per blast. With the high-intensity blast and changing mill control, the plant was easily able to exceed projected mill throughputs with the far more competent Pipeline ore. Strategies to shift the workload and debottleneck the milling circuit were proposed and proven during the milling trials, demonstrating an increase in throughput of 7 per cent despite running at a lower SAG mill speed, and potential of 16 per cent for increasing the SAG mill to standard operating speed. A number of process improvement opportunities have been identified to enhance current productivity and ensure long term capability to process the considerably more competent future ores. All of this is being linked in with the major digitisation program at the Barrick Cortez site, with an objective of linking all the data into a mine-wide process optimisation system, that can embed the processes by providing process-wide data access and production support via the future dynamic models linking ore body knowledge to productivity along the full process chain.CITATION:Powell, M, Yahyaei, M, Geronimo, J, Yussupova, Z and Kumar, P, 2018. The designed approach to mill liner optimisation – experience at Pustynnoye mine, Kazakhstan, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 595–612 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By H R. Phillips

During the 1980s and early 1990s, the South African coal industry experienced a series of methane explosions in which well over 200 coal miners lost their lives. In addition, a fire and an explosion in the gold mining sector claimed a further 240 lives. These tragic incidents resulted in the establishment of a research facility at Kloppersbos dedicated to explosion and fires research and the funding of an extensive research program, and almost certainly influenced the government of the day in its decision to establish, in 1993, the Leon Commission of Enquiry into Mine Health and Safety. The results of this focused research program, the wide-ranging recommendations of the Leon Commission and the determination of the coal mining industry to improve its safety record all combined to result in the past 20 years without a major explosion.This paper lists some of the research outcomes and, through three case studies, illustrates what can be learnt from investigations following explosions. The paper concludes with an evaluation of some of the findings of the Royal Commission on the Pike River coal tragedy. Many of the Commission’s conclusions are pertinent and relevant to the coal mining industry worldwide and their implementation could significantly improve coalmine safety; however, a careful study of the available facts indicates there could well be an alternative explanation of the source of the methane, the location of the ignition and the size of the explosion at the Pike River coalmine.CITATION:Phillips, H R, 2015. Lessons learnt from mine explosions, in Proceedings The Australian Mine Ventilation Conference, pp 19–28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By L. L. Rethi

The U.S. Bureau of Mines summarized injury data for independent contractor employees working at all locations of coal and metal-nonmetal mines from 1983 through 1990. During the eight years, the greatest contrast in degree of injury between independent contractor and operator employees was in fatalities. From 1983 through 1990, there were 132 independent contractor employee fatalities in the mining industry. In 1988 though, independent contractor employees accounted for nearly one-fourth of all mining fatalities. The fatality incidence rates of independent contractors were consistently higher than those of operators during the eight years. For instance, in 1990, the contractors' rate was twice that of operator employees in coalmining and nearly five times that of operators in metal-nonmetal mining. Three other salient facts highlight the independent contractor employees' fatality injury data during these years. First, 82% of the independent contractor employee fatalities occurred at surface locations. Second, two job classifications?truck driver and equipment operator?represented 37% of the fatalities throughout the 8-year period. And finally, four accident classifications?powered haulage, slips and falls, machinery, and electrical?accounted for 71% of all independent contractor employee fatalities.

Jan 1, 1993

By Denise A. Herzog

The U.S. Bureau of Mines conducted a study of cyanide leach technology used in Alaska's mineral industry from 1987 through 1990. Literature and cost data were obtained for mines in the contiguous United States, Canada, and Alaska that use cyanide to recover gold and silver. The data was compiled in an effort to evaluate the economics and conditions associated with cyanide use in Alaska. This report discusses heap leaching methodology and evaluates a "typical" heap leach operation in Nevada and compares the results of the Nevada operation to an analogous hypothetical mine in Interior Alaska. Five daily tonnage rates were analyzed for both the Nevada and the Alaska operations to evaluate the spectrum of economic possibilities. The discounted cash flow rate of return (DCFROR) for each production rate was then evaluated in terms of recoverable metal value (RMV). The Nevada RMV for each production rate was then compared with its Alaskan counterpart, and the results averaged. The Alaskan production costs are an average of 1.71 times greater than costs associated with mining in Nevada at a 0% DCFROR. At 15% DCFROR, costs in Alaska are 2.01 times greater than those in Nevada. Costs are higher in Alaska because of the shorter leaching season, increased labor and transportation costs, and heavier precipitation and vegetation.

Jan 1, 1991

By René Winand

A new process was studied at large laboratory scale at Université Libre de Bruxelles, under contract with Metallurgie Hoboken-Overpelt. A two cathodes (1m long ; 0.2 m high) channel cell was used at 2000 A/m2, with an electrolyte flow rate up to 1.8 m/sec. The main results may be summarized as follows : cathodes are electro¬refined grade in analysis ; metallographic structure and surface roughness are kept under control up to 1.3 cm (one side deposits) ; silver in cathode is controlled by CI and Br ions in solution ; organics must be used at very low concentrations (in the range of 0.1 mg/1, with a consumption of about 0.01 mg/lh).

Jan 1, 1987

First, a classification of the various primary sources of feed materials for the production of cobalt is presented from a mineralogical point of view : sulfides, arsenides, sulfo-arsenides and oxide minerals. Each of these cate- gories will be characterized by its behaviour towards concentration methods, taking account of the presence of the associated minerals of other metals and of the nature of the gangue minerals. Then, for each category of cobalt bea- ring ores, typical flowsheets of treatment will be presented and discussed and the characteristics of the cobalt concentrates produced will be under- lined having in view their subsequent processing by pyro - and (or) hydrome- tallurgical methods.

Jan 1, 1988

By S. Castro

The aim of the present paper is to review the current technologies for arsenic removal in the copper metallurgical industry, and to show the progress made with some promising emerging strategies, involving the pre-treatment of copper-arsenic concentrates by selective flotation or by alkaline leaching with Na2S-NaOH solutions. The advantages of alkaline leaching are the selective dissolution of arsenic and antimony, the high extraction yield, and the practically nil loss of copper, which remains in the clean copper concentrate as a CuS residue. Alkaline ?cured? ? a procedure similar to ?acid-cured? in conventional leaching ? improves arsenic extraction and reagent consumption, making this an interesting technology for the treatment of high As-Sb concentrates. In light of recent advances on the selective flotation of enargite and tennantite, the importance of redox conditions to control the flotation/depression of enargite-tennantite from copper sulfides has been well established. However, problems of selectivity must still be solved. Additionally, the limitation imposed in some cases by the need to recover the molybdenum by-product must be considered. The application of selective flotation to obtain a high-arsenic or ?dirty? concentrate and its sub-sequent treatment by the alkaline leaching process is suggested.

Jan 1, 2014

By McClelland. John J.

This Bureau of Mines report discusses recent applications of water in-fusion technology to control dust in U.S coal mines and presents recommended guidelines for determining coal seam infusibility. The techniques required to use water infusion are presented in detail. A Bureau case study indicated that water infusion reduced dust levels by 68 pct along a longwall plow face, bringing this section into compliance with the Z.0-mg/m3 Federal dust standard. Similar studies conducted by Occidental Research Corp. under a Bureau contract show water infusion at two longwall double-drum shearer operations produced dust reductions ranging from 38 to 50 pct. Water infusion was found to be cost effective, aver-aging 5 cents per ton.

Jan 1, 1987

By James M. Barker

The borate deposits of Death Valley, first exploited in 1882, were a major world source of boron-bearing products until shortly after very large deposits near Boron, California (Kramer) came on stream in 1926. Borate mining in Death Valley then became moribund, with most extant deposits held as reserves backing Kramer. Tenneco began borate operations following acquisition of claims in 1967 and is the only active borate producer inside Death Valley National Mon¬ument. Borate ores, confined to the lower Furnace Creek Formation (early to middle Pliocene), initially precipitated in a shallow lake fed by boron-rich volcanic hot springs associated with the Basin and Range province. Later diagenesis and remobilization plus regional folding, faulting, and erosion altered and complicated originally simple borate mineralogy and distribution. Dominant ore minerals are ulexite (NaCaB509.8H20), probertite (NaCaB509.5H20), and colemanite (Ca2B6011.5H20). Tenneco currently operates two open pits near Ryan, California. Mining is by bulldozer-pushed scrapers hauling waste and front-end loader/off-highway truck combinations for ore and waste haulage. Archeological, environmental, and aesthetic considerations influence both mine plans. Boraxo Pit, opened in 1970, has deep ore (stripping ratio 10 to 13:1) which occurs along a fault and as beds in shale on the hanging wall. Problems include pit wall instability (adverse bedding), non¬ripable calcareous shale (11,000 fps), and mixed ore separation. Sigma Pit, opened in 1975, has shallow (stripping ratio 1 to 1). low dipping, bedded ore in shale. Massive ulexite and "granular" un- cohesive colemanite present problems in mining and milling. Colemanite is crushed to -6 inches, washed, dried at 350°F, then calcined at 800°F with 100 tpd capacity. Crushed (-6 inch) ulexite or probertite is Raymond milled to customer specifications with a capacity of 1000 tpd.

Jan 1, 1976

By J. T. Tanner

The research activities of the Minerals Research Laboratory, which is a part of North Carolina State University, is normally confined to solving beneficiation problems, and developing flotation processes for the mining industry. In recent years the laboratory has veered from its main purpose somewhat and has placed some emphasis on the manufacture of products from mineral concentrates. This has been the result of requests for help from industry. One such request came to the MRL from a talc producer in North Carolina who was having a difficult time competing with foreign imports of steel marking crayons. He felt that if a process could be developed whereby a satisfactory crayon could be produced from powdered talc at a low cost that he could compete.

Jan 1, 1986

By A. D. Fisher

This paper describes the future position of metallurgical coal, particularly as applied to Canadian reserves. Quality coking coal is declining in availability, but preheating practices may alleviate this situation to some extent. Two new processes are discussed in the paper - formed coke and direct reduction - and their coal specifications are outlined.

Jan 1, 1972

By Marcel F. DeGuire

Pilot plant operations are described for the treatment of manganiferous zinc concentrates from the Gamsberg ore deposit in South Africa via conventional electrolytic zinc processing. Two methods were employed for the control of excess manganese ions in the pilot plant electrolyte involving (1) chemical oxidation and (2) anodic oxidation. The chemical oxidation method for manganese control was very successful. It also was found that the addition of manganese dioxide ore was not required for oxidation of ferrous iron during the neutral leach or jarosite precipitation steps. A new method (JAR process) for iron removal also was tested in the pilot plant.

Jan 1, 1978

By Gary P. Sames

This U.S. Bureau of Mines study was conducted in eastern Kentucky drift mines as part of an ongoing research program to characterize the outcrop barrier zone. "Hillseams" were identified as the dominant geologic cause of roof instability unique to the outcrop barrier zone, with many roof fall injuries and fatalities attributed to them. Hillseam is the eastern Kentucky miners term for weather-enlarged tension joints that occur in shallow mine overburden where surface slopes are steep. Hillseams are most conspicuous within 200 ft laterally of a coalbed outcrop and under 300 ft or less of overburden. Hillseams form by stress relief, and therefore tend to parallel topographic contours and ridges. They can intersect at various angles, especially under the nose of a ridge, and create massive blocks or wedges of roof prone to failure. Examples of hillseams are described in both outcrop and in coal mine roof to establish their geologic character and contribution to roof failure.

Jan 1, 1989

By D J. Williams, A K. Kho, A Shokouhi, N Tucker

The disposal of dewatered coalmine tailings and coarse reject within spoil piles is gaining popularity as a means of eliminating separate surface tailings storage facilities or dams. The contrasting characteristics of coalmine spoil, coarse reject and tailings are somewhat complimentary, making the co-disposal of dewatered tailings within spoil piles geotechnically feasible and environmentally attractive. However, the impacts of mixing plant rejects within spoil piles are not well understood; in particular, the effects of water draining from the mixed plant rejects on the moisture content of the surrounding spoil. Changes in moisture content can cause additional collapse and degradation settlements of the spoil pile. A series of laboratory tests has been undertaken on mixtures of dewatered coalmine tailings, coarse reject and spoil. The results of these tests have been incorporated into a spreadsheet-based settlement prediction tool to investigate the effects of incorporating mixed plant rejects on total spoil pile settlements. This paper presents the laboratory tests undertaken, the incorporation of the test data into the settlement prediction tool, and settlement estimates for the various mixtures at different stages of construction.CITATION:Kho, A K, Tucker, N, Williams, D J and Shokouhi, A, 2015. Impact of co-disposing mixed plant rejects on spoil pile settlements, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

Reverse sensitivity is a critical issue for all extractive activities. Extractive industries can only establish in the location of the particular resource sought to be extracted. Avoiding a location near sensitive activities (such as residential activities) may, therefore, be more difficult for extractive industries, than for other industry (such as dairy factories).   This paper focuses on the following matters: +        principles to be derived from case law, +       district and regional council approaches managing reverse sensitivity effects, and +        avoiding, remedying or mitigating reverse sensitivity effects in the future.

Jan 1, 2006