Search Documents

By F. J. Sotillo

"Scrubbing both horizontal (drum) and vertical (attrition) are considered simple unit operations in the beneficiation of phosphate ores. In general, the operating conditions are fixed at high solids content based on the experience of the engineering or equipment manufacturing company responsible of designing this beneficiation step. Nevertheless, scrubbing is a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes, break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Therefore, it is considered that as high solids content as possible should be used to enhance particle-particle interactions (impact and rubbing) without taking into consideration the rheology of the system. However, scrubbing unit operations design requires studying the balance between the increase of particle-particle interactions with the cushion effect that may occur when slimes, clays and fines decrease the availability of free water increasing the apparent viscosity of the phosphate slurry up to that of a paste consistency. This paper presents data from laboratory tests to determine the best operating conditions for the design of these unit operations based on the highest P2O5 grade obtained with the lowest impurities for different size fractions. INTRODUCTION In the beneficiation of phosphate ores, unit operations such as horizontal scrubbing (drum) and vertical scrubbing (attrition) are considered simple unit operations. Therefore, little attention is given to the design of horizontal and vertical scrubbing during the basic engineering studies, and the detail engineering stage, the manufacturers recommending “standard” units and operating conditions based on their experience. Due diligence of several beneficiation phosphate plants at industrial scale indicates that a deficient scrubbing of the phosphate ore results in significant problems in downstream unit operations, such as classification, clarification, gravity separation, magnetic separation, flotation, dewatering, and filtration. Scrubbing is in fact a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes (clays and fines), break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Two phenomena occur, the particle-particle interaction (impact and rubbing), and the rheological effects of releasing significant amount of fines into the slurry. Therefore, high solids contents are recommended to enhance the particle-particle interactions, which may result in a change in the rheological regime of the system due to the slimes, clays, and fines decreasing the availability of free water. This increases the apparent viscosity of the system up to that of paste consistency resulting in a cushion effect that suppresses scrubbing. Under these conditions, not all fines are release and rejected (deslimed), downstream unit operations being affected by the release of clays, resulting in P2O5 losses."

Jan 1, 2017

By Donald F. Smith

This report describes the construction and calibration of two ice calorimeters and includes results of high-temperature heat-content measurements, made by the Federal Bureau of Mines, on rubidium fluoride, hafnium tetrafluoride, cesium chloride, and cesium iodide. The heats and entropies of fusion of rubidium fluoride, cesium chloride, and cesium iodide have been calculated at their respective melting points using equations derived from the experimental heat-content data. Hafnium tetrafluoride did not melt within the range of temperatures investigated. Heat and entropy of transition of cesium chloride from the alpha to the beta form were also determined. INTRODUCTION Free-energy data usually afford the cheapest and quickest means of determining the feasibility of experimentally untested reactions. For known reactions, free-energy data show the variation of the equilibrium constant with temperature and make it possible to calculate, without experiment, the maximum ratio of product to raw material for a given chemical process.

Jan 1, 1961

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60's, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, Pso, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of 02 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003

By J. Klemenic

This paper presents an analysis of gold production and prices over an extended period. Production patterns are provided for the world as a whole and for the five major producing countries. Gold prices as a function of interest rates, as measured by municipal bond rates, are given for the period 1947 to the present. World gold production has had a phenomenal increase since 1980, with the exception of South Africa, all major producing nations participated in this increase, even though the price of gold generally has been decreasing since the high level attained in 1980.

Jan 1, 1993

By D. S. Colby

The productive capacity of natural-gasoline and cycle plants in the United States as of January 1, 1952 was 811,596 barrels per day, an increase of 163,691 barrels per day since the last survey on January 1, 1950. The rate of growth during these 2 years has been 12 percent per year s only slightly below the maximum rate, recorded from 1948-50. This survey, for the first time, presents capacity data on a barrel rather than a gallon basis. Also, for the first time, a break-down of capacity by products has been obtained. The combined LP-gas producing capacity of plants and fractionators equaled 382,790 barrels per day, 47 percent of the total industry capacity tor all products. During January 1952, LP-gas and natural gasoline and other products were each produced at the rate of 76 percent of the January 1 capacity.

Jan 1, 1952

By S. Wimpfen

El presente texto señala la adecuación de las reservas y recursos mundiales de cobre y aluminio para abastecer las necesidades mundiales de los mismos hasta el año 2000 a través del registro y análisis de las relaciones históricas que existen entre el crecimiento de la población y el crecimiento económico, consumo del metal, producción, reservas y recursos durante el período de la Post Guerra II. Así como la comparación de los requerimientos acumulativos de cobre y aluminio con los últimos estimados de reservas y recursos mundiales, según el Departamento de Minas de U.S.A. y el Levantamiento Geológico de U.S.A.

Sep 1, 1978

By M. -H. Fillion

"Geotechnical stability analysis and design in open pit mines requires access to representative geological, structural, hydrogeological, and rock mass models. The quality and quantity of collected geomechanical data used to build such models can have significant implications in the design of safe and economically viable slopes. Data collection is a continuous process throughout the life of a mine. The process starts from exploration to conceptual/preliminary feasibility, feasibility, design and construction, operations (early production/late production), and mine closure.As geomechanical data is often limited at an early stage of a project, the estimated variability of the geotechnical factors may be larger than the actual data variability. This can potentially result in a conservative selection of the pit slope angle. Collecting additional geomechanical data at later stages of the mine development may contribute to reducing the uncertainty associated with the geotechnical properties and a steeper slope angle may be used for the design. This can result in significant economic benefits.This paper investigates the impact of access to new data over time, following a series of geomechanical data collection campaigns, on design decisions. This is illustrated by comparing the resulting slope design, at three stages of the mine project, at a South African open pit mine. To demonstrate this, a series of slope stability analyses were performed using limit equilibrium tools. For each project stage, the slope angle design was modified until a similar probability of failure of 5% or less was obtained. The corresponding factor of safety distributions for each project stage were then compared to evaluate the impact of collecting additional data on the resulting slope design.The results showed that data variability can differ significantly from one project stage to another. Data variability may be greater at more advanced project stages (i.e. a wider distribution of the factor of safety). Furthermore, the results showed that, even for the cases with greater variability, steeper slope angles were possible at more advanced stages for the proposed design requirement (probability of failure < 5%). In this investigation, as more data became available, the uncertainty associated with data variability could be sufficiently reduced to allow the selection of less conservative slope angles. This can be used as a managerial tool in developing data collection strategies and allocating the necessary funds, and can lead to important economic benefits to the mining operation."

Jan 1, 2016

By V. T. McLemore

"Lindgren (1933) defined a belt of alkaline-igneous rocks associated with large quantities of gold and rare earth elements (REE) that extends from Alaska and British Columbia southward into New Mexico, Texas and eastern Mexico. The North American Cordilleran alkaline-igneous belt since has been exploited for numerous types of mineral deposits. In New Mexico, Mid-Tertiary alkaline to calc-alkaline rocks are found with seven types of deposits in these districts: (1) polymetallic epithermal/mesothermal veins, (2) gold-bearing breccias/quartz veins, (3) Cu-Au, Au and Mo porphyry deposits, (4) skarns and carbonate-hosted deposits, (5) iron skarns and replacement bodies (with some gold), (6) gold placers, and (7) Th-REE (with some U, Nb) epithermal veins. Some of New Mexico’s largest gold and REE deposits are found within this belt. Their origin is not well understood, but a compilation of new data (age dates, isotopic and chemical analyses) allows for a better understanding. The diversity of igneous rocks and associated mineral deposits along this belt suggests that this region is characterized by highly fractionated and differentiated; multiple pulses of magmas and involves both upper mantle and lower crustal sources. Once magmas and metal-rich fluids reached shallow levels, local structures and wall rock compositions determined distribution of and final style of intrusions and resulting mineral deposits. INTRODUCTION Lindgren (1933) was one of the first geologists who noted that a belt of alkaline-igneous rocks extends from Alaska and British Columbia southward into New Mexico, Trans-Pecos Texas, and eastern Mexico (Fig. 1) and that these rocks contain relatively large quantities of gold, fluorine, zirconium, rare earth elements (REE), and other elements. Since then, the North American Cordilleran alkaline-igneous belt has been explored and exploited for numerous types of mineral deposits, especially gold. The North American Cordilleran alkaline belt is a north-south belt of alkaline igneous rocks and crustal thickening, roughly coinciding with the Great Plains physiographic margin with the Basin and Range (Rio Grande rift) and Rocky Mountains physiographic provinces (Mutschler et al., 1985, 1991; Bonham, 1988; Thompson, 1991a; Richards, 1995; McLemore, 1996; Jensen and Barton, 2000; Kelley and Luddington, 2002). Deposits within this belt have produced significant amounts of gold in the United States and Canada and include Cripple Creek, Colorado (702 metric tons of gold production), Black Hills, South Dakota (235 metric tons gold production) and Landsky-Zortman, Montana. In New Mexico, the North American Cordilleran alkaline belt extends from the Sangre de Cristo Mountains near Raton, southward to the Cornudas Mountains, in the northern Trans-Pecos alkaline belt (Fig. 2). The alkaline-igneous related mineral deposits in New Mexico have been referred to as Great Plains Margin (GPM) deposits by North and McLemore (1986, 1988) and McLemore (1996, 2001). Alternative classifications by other workers include Au-Ag-Te veins (Cox and Bagby, 1986; Bliss et al., 1992; Kelley et al., 1998), alkalic-gold or alkaline-igneous related gold deposits (Fulp and Woodward, 1991a; Thompson, 1991a, b; Bonham, 1988; Mutschler et al., 1985, 1991; Richards, 1995), porphyry gold deposits, and the North American Cordilleran belt of alkaline igneous rocks (Woolley, 1987; Mutschler et al., 1991)."

Jan 1, 2015

By R. E. Mussier

This investigation was made to study new methods to prepare high-purity yttrium metal, Various methods were used to prepare pure intermediate compounds, primarily chlorides, bromides, and iodides, which were subsequently reduced to metal. The process found most suitable for the preparation of pure anhydrous yttrium chloride involved thermal dehydration of a mixture of hydrated yttrium chloride and ammonium chloride while under vacuum. Yttrium bromide and iodide were prepared most effectively by the direct halogenation of yttrim carbide. Yttrim carbide was obtained by reacting and melting yttrium oxide-carbon mixtures in a carbon-arc furnace. Yttrium halides were purified by vacuum distillation and reduced by alkali or alkaline-earth metals. Lithium and sodium proved to be the best reductants from the standpoint of yield (>95 pct) and purity (>99.8 pct) of the yttrium. The product of the reduction step was sponge metal, which was consolidated readily by conventional cold-mold, arc-melting procedure. The purest yttrium obtained in laboratory scale work was prepared by sodium reduction of yttrium chloride and contained only 125 pp oxygen; other impurities did not exceed 1,000 ppm. In larger scale tests yttrium containing only 800 to 1,000 ppm total impurities was obtained by lithium reduction of yttrium chloride. The tensile properties of high-purity yttrium were determined. Mechanical tests showed that yttrium can be forged, extruded, rolled, spot welded, and deep drawn.

Jan 1, 1963

By John Paul Gries

During World War II, when the curtailment of imports led to an unprecedented demand for domestically produced mica, beryl, and other pegmatitic minerals, the Bureau of Mines and the Geological Survey entered upon a program designed to expedite the production of these minerals from the Black Hills area of South Dakota. The program involved mapping, sampling and drilling many pegmatite dikes found in the southern portion of the area and beneficiation tests in the field and in the Bureau of Mines laboratories at Rapid. City, S. Dak., Rolla, Mo., Salt Lake City, Utah, and College Park, Md. This paper describes the mode of occurrence and the sampling and beneficiation tests on one dike, the Helen Beryl pegmatite, which was investigated as part of the general pegmatite study in South Dakota. Investigation of the Helen Beryl Pegmatite by the Bureau began in August 1943 and was terminated in April 1944. During this period the Bureau took a series of bulk samples from pits for beneficiation tests, drove an adit through the center of the dike to obtain feed for a bulk-sampling plant operation, and finally drilled a series of long holes to sample the deposit further. Geologists of the Federal Geological Survey mapped the deposit and the faces of all excavations and logged drill holes from sludge samples recovered from long-hole drilling.

Jan 1, 1949

By Jack L. Henry

The Bureau of Mines conducted seven pioneering experiments in a 12-inch-diameter Kroll reduction reactor to examine the feasibility of coreducing the chlorides of Ti, AI, and V to produce a homogeneous titanium alloy sponge. The coreduction studies proceeded in a normal manner, and the yields of sponge were comparable with those of pure titanium sponge made in the same reactor. Vanadium concentration was very uniform throughout the sponge cake when VC14 in solution in TiCl4 was fed into the molten magnesium. More difficulty was encountered in feeding solid VCl2 and AIC13. Vanadium and aluminum concentration in the sponge was not uniform, and mechanical difficulties were experienced with the small-scale screw feeder. Although the sponge varied in composition from region to region, the ingots prepared from it were uniform in composition.

Jan 1, 1974

By E. E. Maust

The literature on the activation of sphalerite for flotation by short¬chain xanthates leaves unanswered the question of whether a compact surface film of activator sulfide is necessary or merely sufficient for high flotation recoveries. Studies by Guarnaschelli and Plaksin indicate that xanthate adsorption and flotation of sphalerite are increased with increasing hole/ electron ratio. These results, and the known acceptorlike behavior of many heavy-metal impurities in zinc sulfide, suggest that activation may result from a traditional semiconductor doping effect at the surface. Using the theory of chemisorption states on ionic crystals as developed by Levine and Mark, the Bureau of Mines has carried out A calculation to estimate the surface-state energies of various metals when they are substituted at zinc sites on (110) sphalerite surfaces. Based on a simple Madelung-Born treatment of ionic solids, the calculation indicates that many of the metals known to activate sphalerite for subsequent flotation have lower surface-state energies than nonactivators. The results of these calculations are discussed from the standpoint of consistency with the proposed activation mechanism and observed flotation results. The satisfactory agreement obtained is taken to be support for the proposed mechanism, and further elaboration of a surface-doping model is attempted.

Jan 1, 1976

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By Tulu B. Ihsan, Mark A. Van Dyke, Ted M. Klemetti

"How well do current modeling procedures calculate the rear abutment extent and loading? Does an improved understanding of the rear abutment extent warrant a change in standing support in bleeder entries? What is the optimal standing support for bleeder entries separated from the longwall startup room by a barrier pillar? To help answer these questions and to determine the current utilization of standing support in bleeder entries, four bleeder entries at varying distances from the startup room were instrumented, observed, and numerically modeled. This evaluation was intended to determine the rear abutment extent and magnitude at various locations to optimize standing support in these entries and those under similar conditions. This paper details observations made by NIOSH researchers in the bleeder entries of a deep cover longwall panel; specifically data collected from instrumented pumpable cribs, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was on the extent and magnitude of the abutment loading experienced by the standing support. As expected, the instrumentation of the standing supports showed very little loading relative to the capacity of the standing supports—less than 25 tons load and 1 inch convergence. The observations of the conditions showed little to no change from before the longwall panel extraction began to when the panel was more than 50% extracted. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the bleeder design. The Flac3D program was used to evaluate these four bleeder entries using previously defined modeling and input parameter estimation procedures. The results indicated only a minor increase in load during the extraction of the longwall panel. The model showed a much greater increase in stress due to the development of the gateroad and bleeder entries, with about 80% of the increase associated with development and 20% with longwall extraction. The Flac3D model showed very good correlation between expected gateroad loading during panel extraction and those expected based on previous studies. The front and side abutment extent modeled was very similar to observations from this and previous panels with similar conditions. The results of this study showed that the rear abutment stress experienced by this bleeder entry design was minimal. The convergence measured in these bleeder entries was small enough not to mandate any additional support beyond development even by U.S. or Australian standards. The pumpable crib load and convergence experienced depends on the geological setting, mining geometries, and timing. The farther away from the startup room, the lower the applied load and smaller the convergence in the entry if all else is held constant. Finally, the numerical modeling method used in this study was capable of replicating the expected and measured results near seam."

Jan 1, 2017

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By John T. Metcalf

The assembly procedures for nine different wire rope terminations used in the mining industry are presented in a format and manner to facilitate training and to provide points where inspection of the termination should be performed. The nine terminations addressed are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Sleeve & Thimble, Thimble Splice with Four Tucks, U-Bolt Clip & Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The manual was prepared to be used primarily for field type mining operations or training where high capacity machinery is quite limited. It is nut the intent of this manual to suggest that the procedures presented are those to be used by manufacturers or other commercial enterprizes. A different set of procedures may be more appropriate where ideal space and equipment resources are available. The assembly procedures were derived from standard industrial practice, manufacturer&apos;s recommendations, and the open literature on the subject. These same procedures were used to prapare test specimens for an extensive series of pull and axial fatigue tests. The results of these tests indicate that these procedures are satisfactory in all respects. This manual is to be used as part of a complete training program. Although a brief glossary is included, there has been no attempt to make this a primer on wire rope. The selection of wire rope termination hardware, like the selection of the wire rope, is a subject not covered by this manual. The reader is cautioned that there are various sources for such hardware and this selection must be done carefully.

Jan 1, 1978

By Clarence O. Babcock

This report describes the results of Bureau of Mines laboratory and preliminary field tests on a rock bolt of helical shape. The flexible construction allows the bolt to maintain a more stable load level than is possible with a straight bolt. Bolt load changes resulting from anchor slippage, blasting shock, or changes in mine geometry with mining advance are minimized. Preliminary field tests were performed at the Kaiser Steel York Canyon mine where the load changes of straight and helical bolts were measured using a vibrating-wire load gage. The field tests were performed to establish the viability of the concept of a helical bolt. The practical usefulness in terms of performance and economics remains to be shown. The change in bolt load for the flexible bolts was one-third that for the straight bolts. There were no malfunctions of the gage, and the bolts maintained a more uniform load than the straight bolts used as controls.

Jan 1, 1978

By Raja V. Ramani, Wilson Miola

"The potential health effects of quartz-bearing airborne dust in mine and mill atmospheres point to the need for the quantification of quartz content in the source material for determining the source-sink relationships and for choosing applicable control measures. While a standard method exists from a regulatory point of view for the sampling of coal mine atmospheres for determining (i) respirable dust concentrations and (ii) the amount of quartz in the samples, there is no generally accepted standard method for quartz analysis in bulk samples of coal and host rocks. Generally, the bulk sample is reduced to a powder for producing quartz analysis samples. Extensive controls arc necessary to ensure representativeness of the analysis samples when these are very minute fractions of the bulk samples. Since the amount of analysis sample is not limited, alternative methods for quartz analysis may also be tried. It is, however, necessary to adopt a procedure which will satisfy several statistical requirements to guarantee representativeness of the quartz analysis samples.In this paper, the important factors in the preparation of quartz analysis samples from the host rocks and bulk samples are discussed. The method developed to prepare the analysis samples is outlined. The results of application of the procedures are presented. The procedure developed for quartz analysis sample preparation is based on sound statistical foundations. The procedure has been validated for reproducibility and homogeneity.The current methods used for quartz analysis in powders are the P-7 infrared spectrometry and quantitative X-Ray Diffraction (XRD). Both have similar restrictions concerning the sample characteristics and operational problems, which arc intrinsic to radiation beams, device geometry, mechanics and controls of the radiation behavior. Although improvements can be made in the spectrometers and diffractometers, some of the most important steps are the procedures for analysis sample preparation from bulk samples and for calibration of the instruments. The sample preparation process is often referred to as one of grinding and sizing the bulk sample to generate the powder for the scanning devices. The particle sizes are referred to and their influence emphasized but the representativeness of the sample is assumed. Assuring sample representativeness during the sample preparation procedures is critical.For the sampling of airborne respirable dust in coal mines, the collection devices, the collection procedures and the analysis procedures are defined. This is not true for bulk samples where weights must be reduced thousands of times to generate the analysis samples for the scanning devices. The specifications to be developed may include bulk sample amount, sample reduction procedures, sample particle size distribution and sample amounts. However, the common problem of insufficient sample amount which is often encountered with mine airborne dust samples need not exist for bulk samples. Further, the same bulk sample can yield analysis samples for several experiments. The latter, of course, requires sample homogeneity.Three concepts are important in the selection of any procedure for sample preparation and analysis. These arc accuracy, reproducibility and representativeness. The adopted procedure has to guarantee a homogeneous sample representative of the population, a defined level of accuracy and reproducibility. Important statistical concepts are embedded in these requirements, particularly with respect to estimation and dispersion errors. Accuracy and reproducibility are totally different though not independent concepts. Estimation is related to accuracy and the true value. Dispersion is related to reproducibility and is measured by the classical statistical standard deviation of the distribution of a series of measurements or analysis performed over the same lot or analysis sample. The dispersion variance (or dispersion error) does not tell a"

Mar 1, 1992

In 2011, the value of mineral production increased in the United States for the second consecutive year (Table 1). Production increased modestly for most mineral commodities mined in the United States, and price increases, especially for precious metals, resulted in increases in the value of production. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals? contribution to the GDP increased for the second consecutive year. Trends in other sectors of the domestic economy were similar to those in mineral production and consumption rates. U.S. apparent mineral consumption (industrial) of 11 mineral commodities decreased substantially from 2005 to 2010 (aluminum, cadmium, cement, copper, iron, lead, salt, soda ash, steel, tin and zinc). Data for 2011 were not calculated, but the data show a sustained decrease (especially for the metals) preceding the recession through 2010, so consumption seems to be behaving differently than production and GDP. After continued decline following the 2008?2009 recession, the construction industry began to show signs of improvement during 2011, with increased production and consumption of cement, construction sand and gravel, and gypsum ? mineral commodities that are used almost exclusively in construction. Crushed stone production, however, continued to decline.

Jan 1, 2012

By Donald W. Mitchell

Certification tests for urethane-foam systems and techniques for apply-ing foam safely in mines are described. Fire hazard from foam exists if flame propagates beyond the ignition source or penetrates the foam. Foam that passes the certification tests can be applied on stoppings, continuous sections of ribs of relatively wide passageways (with no foam on the roof), short sections of roof such as overcasts, roof cavities, and intersections (with no foam on the ribs), and between buntons on one wall of a shaft. Foam on the ribs and adjoining roof presents a fire hazard. Stoppings covered with foam passing the certification tests are resistant to penetration of heat, flame, and smoke than similar stopping without foam. Flame propagation can be arrested by water sprays. Spontaneous ignition of foam can be prevented.

Jan 1, 1966