Search Documents

By W Barry Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire, Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1992

"Blasthole deviation is a frequent, well documented and undesirable occurrence in mining operations. It is caused by the drill string mechanics, operating variables and the 'interactionbetween the drill bit and the rock mass characteristics. It is composed of three distinct components: collaring or marking error, alignment error and trajectory deviation. This study has focussedon the dependence of trajectory or natural deviation on the geological features of the rock mass being drilled."

Jan 1, 1996

By Zuhair A. Nawab, Muhammad A. Al-Marhqun, Mehmet Guney

"The Atlantis-Il-Deep is a stratified metalliferous deposit located along the median valley of the Red Sea at a water depth of about 2200 m. The metal-bearing mud contains sulphides of zinc, copper and iron with significant amounts of silver, gold and cobalt. A variety of oxide, siliceous and carbonaceous gangue material is also present. Long sediment cores indicate that the thickness of the deposit may reach 25 m, but the average kriged thickness of metal-rich sediments is about 11 m.Mining geostatistics was applied to estimate the Red Sea offshore mineral resources. Experimental semi-variograms were computed along 0 ± 180 degrees and then models were fitted to analyze the mineralization phenomenon. Kriging estimates indicate that 696.330 million t of bulk sediments contain 1.891 million t of zinc, 0.425 million t of copper and 3. 75 thousand t of silver. Gold and cobalt contents were calculated from the analysis of solids in flotation concentrates as 47 t and 5368 t respectively. The significant outcome of implementing geostatistics to the Red Sea brine precipitates is not only for the evaluation of metal resources, but it also provides a useful tool in the optimization of selective dredging of appropriate areas to be mined. IntroductionThe discovery and extensive exploration of hot brines and hydrothermal sediments in the Red Sea median valley revealed the fact that the Atlantis-II-Deep is a potentially exploitable metalliferous mud in the economic sense. Sediments in the mineralized deep are composed mainly of oxides, various types of silicates and sulphides with considerable concentrations of zinc, copper, cadmium, silver and gold. The mineral-rich deposit, located at a mean water depth of about 2000 m, has an average thickness of 11 m, and is covered by a brine layer having a temperature of 60°C."

Jan 1, 1988

Disclaimer ?You may hear something today that surprises you. If you are pregnant or have a heart condition, you may elect to stop hearing now. ?Some of what you are about to hear you may already know. ?Much of what you are about to hear and see is information that is from and can be found via other sources. ?If any of my statements during the course of this presentation are thought or found to be incorrect, I am not responsible for these comments.

Jan 1, 2006

The small scale alluvial gold mining industry in Papua New Guinea (PNG) is c.irrently the only form of small scale mining carried out in this country. It already contributes significantly to the economy with current production estimated at 2 000-2 500kg per year. Until recently, small scale alluvial gold mining has been confined to simple panning and sluicing of high grade alluvial and colluvial deposits. Traditionally the small scale miner in PNG has only worked gravels with gold grades in excess of 500mg/m3. Grades of this order are required to justify the hard physical labour involved ~n hand operated small scale mining methods. .he introduction of higher throughput technologies such as trommels fed by hydraulic excavators has the effect of altering what constitutes an economically viable deposit. Mechanised techniques allow for the consideration of grades of almost half that level. The potential and opportunities for utilising this type of small scale mechanised mining in PNG are enormous with large areas of ground with gold grades running in excess of 250mg/m3 and often up to 2000mg/m3 throughout the country. An assessment of the current operating economics of this technology in the PNG context is the principal objective of this paper. Small to medium scale mechanised mining can potentially contribute significantly to the PNG economy particularly as it lies within the react-, of many PNG businessmen. Its potential is currently somewhat limited by a general lack of infrastructure and is also constrained by socio-political factors.

Jan 1, 1991

By Delahant A. B, Dworski M

From the Saranac Laboratory for the Study of Tuberculosis of the Edward L., Trudeau Foundation, Saranac Lake, New York:We are assembled to honor the memory of our friend and colleague, Donald Cummings, one of the founders and a past president of the American Industrial Hygiene Association. I deem it an Unusual privilege to have been asked to give this first memorial lecture and hope that what shall have to say may be worthy of the occasion. It is fitting that we should discuss here the subject of Silicosis to which he devoted such a large part of his life and it is doubly fitting, I think, that I should report to you an extended series of investigations carried on by his associates at the Saranac Laboratory.The subject of silicosis may seem hackneyed to this audience which is so familiar with the tried and accepted methods of prevention and control.But in spite of our efforts, the condition is still with us and unfortunately is still being produced in many places. In industries that now maintain good control of dust, fresh cases are appearing on annual re-examination, whose major exposure date back to the days before the hazard was recognized.A few new employees, with apparently ineffective upper respiratory protection against inhaled dust, develop silicosis precociously in environments that are comparatively harmless to their fellows. In plants that have relaxed their vigilance under the urgency of war production schedules, conditions again prevail that will produce, disease in the future.Silicosis acquired new interest with the announcement by Denny, Robson and Irwin(1) in 1937 that it could be prevented by the inhalation of powdered metallic aluminium. It so happened that without knowledge of their work, we at the Saranac Laboratory had for some months been conducting similar experiments with one of the hydroxides of aluminium.Quite independently we discovered that hydrated alumina would also protect animals against quartz. Our approach to the problem had been empirical; we were trying to neutralize quartz particles by coating their surfaces with an insoluble material following the lead of Kettle who in 1932 had shown that this could be accomplished with iron. He neglected to describe his method and the chemist who prepared his coated...

Jan 1, 1945

By P. M. Prasad

Off-grade molybdenite concentrates, mainly derived from secondary sources as by-products of the processing of copper, uranium and tungsten ores, do not satisfy the purity requirements (percent MoS2) for the production of molybdenum bearing products. This investigation is a continuation of a successful effort to refine a low-grade molybdenite concentrate to prepare a high-grade MoS2 using a mixed acid (HF + HCl) leach procedure. Specifically, this investigation is concerned with an understanding of the separation chemistry underlying the removal of the oxide/silicate gangue and the base-metal sulfide associations present in the low-grade molybdenite by their selective dissolution in the two acids. Experiments were conducted on an off-grade concentrate containing 42.6% Mo. Results of the controlled dissolution tests indicate that both HCl and HF are suitable for the removal of the associated alumina and both work well for iron, nickel and copper. However, HF was found to be the most effective for dissolving silica/silicate and magnesia. An attempt was made to rank the leaching efficiencies of the acids used singly, sequentially or in a mixed mode. Scale-up (300 to 2,000 g) experiments were conducted to validate this approach. Excellent purification of the concentrate was possible by processing the off-grade concentrate with 10% HCl plus 15% HF at 363 K for 7.2 ks in open polypropylene reactors with internal stirring. These conditions leached practically all of the oxide and silicate gangue and 96% of the metallic impurities. Starting from the low-grade molybdenite concentrate (42.6% Mo; 71.1% MoS2) it was found feasible to obtain a refined product containing 97.8% MoS2, which is suitable for industrial use.

Jan 1, 2007

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of copper cementation with zinc in sulphate solution. For copper concentrations of the order of 10 p.p.m., a porous, adherent deposit is formed on the zinc surface and this has a significant influence on the reaction rate. When the specific mass of deposit is less than about O· 35 mg/cm2 the surface may be considered as smooth and the rate is described by simple convective counter diffusion of zinc and copper ions through a laminar diffusion boundary layer to the deposit-solution interface. In the presence of additional deposit, the diffusional mass transfer rate is increased by increased surface roughness.The rate under these conditions is first order, with the degree of enhancement independent of further increases in the specific deposit mass. The enhancement in rateis, however, directly related to the initial mass flux and the species involved in the reaction.Preliminary work showed the same mechanism to apply to cementation from chloride solution, solutions of high zinc concentration, and cementation of copper with iron..

Jan 1, 1970

By Brown A

An experimental evaluation of a selective agglomeration process in which an agglomerated coal rich phase was produced as a result of mixing light oil to various raw coal slurries is described. The beneficiation achieved by this method is compared to that obtained bv conventional froth flotation. The results suggest' that oil agglomeration is a more selective process than froth flotation and is less sensitive to variations in feed pulp density. Selective agglomeration has the additional advantage of producing a low moisture content product. The effect of replacing flotation filter cake with an equivalent amount of selectively agglomerated product in coke-making was studied with the aid of a pilot-scale coke oven. The results suggest that the principal effect of such a measure is to increase the bulk density of the charge.

Jan 1, 1977

By C. J. A. Davie

"SUMMARY A practical application of nitric acid oxidation of sulphides, based on the principles of the Arseno process, has been developed for the Cinola ore. Development of the process has been based on testwork conducted by Bacon Donaldson of Vancouver and Hazen Research of Denver, and on conceptual engineering performed by Minproc Engineers of Denver.A comprehensive Stage II report for the project has been submitted to the B.C. permitting agencies, containing provisions for a zero discharge tailings impoundment system and prevention of acid mine drainage. Approval in principle is expected in early 1989.A feasibility study recently completed by Minproc Engineers and Davy McKee Corporation demonstrates that this project can be brought to production for a capital expenditure of C$120 million for a mill throughput of 6,000 tonnes/day and operated at a total direct operating cost of less than $20/tonne.INTRODUCTION The Cinola orebody was discovered in 1970. It is situated approximately in the centre of Graham Island, the largest of the Queen Charlotte Islands. It represents the mid to upper levels of a hydrothermal precious metals system, characterized by intense brecciation and silicification. Gold is associated with finely disseminated sulphides in a breccia matrix and in free form in numerous quartz veins.Ownership of the property has changed hands a number of times, and previous attempts to bring the property to production have failed. Two critical factors have frequently been blamed for difficulty in creating a successful project: namely, process and environment factors, hence the title of this paper.City Resources (Canada) Limited (""City"") acquired the property in 1986, and commenced an aggressive campaign to verify ore reserves, to carry out metallurgical research and to address environmental issues.PROJECT OVERVIEW When the Cinola orebody was discovered, the significance of hydrothermal mineraliza¬tion associated with crustal plate boundaries was not recognized, and for several years, the orebody was considered an uneconomic curiosity. If the type and location of orebody sought by many companies engaged in gold exploration were to be specified, it would probably be a description of the Cinola orebody - it is a large (greater than 1.5 million ounce), low grade (2.45 gm/tonne), refractory ore reserve associated with the Pacific rim crustal plate boundary. The industry appears to have recognized in the past few years that its future lies in the exploitation of such orebodies, and is prepared to come to grips with the technical problems associated with such ores. In this sense, the Cinola orebody might be considered to have come of age."

Jan 1, 1989

By C Doblin

Any value addition to the mineral sands in the Murray Basin (Australia) will generate waste that needs to be disposed of safely. For example, conversion of ilmenite and synthetic rutile to titania (TiO2) pigment would generate large amounts of environmentally undesirable elements. Processing of U+Th containing zircon sands to zirconia or to higher purity zircon would generate a low-level radioactive waste. In this study it is proposed that one way to circumvent the waste problem could be to contain such waste in magnesium-based (Sorel) cements. Containment of waste in magnesium cements is an attractive idea especially for the mineral sand processing companies that could operate in the Murray Basin in the future, because the required magnesium oxide and magnesium chloride may be made cheaply from the saline waters encountered during mining operations. The magnesium cement production process is also far less energy intensive than the Portland cement production process. The results of this study indicate that mixing a waste stream with a slurry of magnesium cement before being discharged to the disposal area would contain the waste in a æconcrete-likeÆ structure, resistant to dispersion by wind and moderate rain. However, some loss of strength and increased leaching of impurities, Mg and Cl could take place in wet climate areas. Ongoing research is being concentrated to develop a new process for making water-resistant magnesium cement.

Jan 1, 2002

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010

By H Saw, M Cordova

Cemented rock fill (CRF) is often used to support open stope voids. This allows for the full recovery of ore while achieving global mine stability. In such cases, the exposed CRF masses require adequate compressive strength and stiffness to resist the forces and limit the displacement associated with movements in the rock mass surrounding the excavations. The CRF material preparation often involves the use of large particles, either from crushed rock or development mining waste. This means that conventional laboratory samples cannot be readily used to determine the laboratory strength. Consequently, a research project was undertaken to determine the influence of sample size on uniaxial compressive strength. This paper presents the results from CRF samples that were prepared using the same mix design and then cast into moulds with diameters of 150, 240, 300 and 400 mm. The laboratory testing also allowed a better understanding of the effect of particle size distribution upon the overall strength of a rock fill mass. The laboratory results were compared to a database of large-scale results from the testing of fill masses from a number of mine sites.CITATION:Cordova, M, Saw, H and Villaescusa, E, 2016. Laboratory testing of cemented rock fill for open stope support, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 755–762 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A Priatna, H Rumbino, T Casten

This paper discusses the progress of the Deep Mill Level Zone (DMLZ) mine from the pre-feasibility study completed in 2005, through commencement of development access in 2008, completion of the feasibility in 2010 and cave initiation in late 2015. This fourth lift of caving in the East Ertsberg Skarn System (EESS) is located 500 m below the currently producing Deep Ore Zone (DOZ) mine and represents approximately half a billion tonnes of ore and around 1900 planned drawpoints, scheduled to be mined at a peak of 80 000 t/d.The paper reviews the mine design, access requirements, planned footprint sequence and major fixed facility installations such as ventilation, oreflow and shops. A discussion of the preproduction development and construction activities and some of the critical technical challenges overcome during this time frame are addressed, as well as the cave initiation process undertaken in late 2015 and the ramp-up of production and progression of caving.CITATION:Casten, T, Priatna, A and Rumbino, H, 2016. Deep Mill Level Zone – from feasibility to production, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 635–644 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By H Sofatzis, J Kinal, J Siliezar, B Kirkwood

Ernest Henry Mining (EHM) is a copper, gold and magnetite mining and processing operation located 38 kilometres north east of Cloncurry in the Mount Isa - Cloncurry mineral district of north west Queensland, Australia. The EHM ore body is an iron oxide copper gold deposit with an average grade of 1.1 percent copper, 0.5 g/tonne gold and 22 percent magnetite.At the end of 2009, after a series of promising laboratory test work, EHM converted the ball mill media charge from forged steel to high chrome media. Laboratory test work also indicated that with the use of high chrome media, the pH was able to be reduced with no negative impact on plant performance. At high pH values (above 10.5), the forged media is passivated, so as the pH of the system drops the media corrosion rate increases and floods the system with corrosion products, affecting flotation. As the high chrome media is much more inert, pH has less of an effect on copper flotation response.This paper provides an overview of the effects of reducing the pH in the EHM copper rougher flotation circuit. The pH in the roughers was dropped from 10.6 to 9.6 to determine the impact on the rougher performance and the subsequent performance of the whole copper flotation circuit. It was found that there was a slightly increased improvement in copper recovery and no statistical change in either the rougher or final copper concentrate grades for copper and gold.With the reduction in pH, there was a noticeable reduction in lime usage from 0.85 kg of lime per tonne of ore processed to 0.55 kg/t. This reduction in lime is equivalent to approximately $700,000 per annum at current production rates.CITATION:Kirkwood, B, Kinal, J, Siliezar, J and Sofatzis, H, 2013. Low pH trial in the Ernest Henry Mining copper rougher flotation circuit, in Proceedings MetPlant 2013 , pp 371-377 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Hua-Zhong Yu

Gold is one of the most widely used substrate materials for self-assembly. Self-assembled monolayers (SAMs) prepared from alkanethiols and their derivatives on gold are the most reliable and well-studied systems to date, which have attracted much attention because of interest in two-dimensional molecular assemblies, and of their potential applications in molecular devices, sensors, and functionalized interfaces. Gold electrodes are also very important in microelectronics and electroanalytical chemistry. This work reports the characterization of a new type of gold substrates for self-assembly. The gold substrates are constructed from recordable compact disks (R-CDs) with simple and straightforward wet-chemical treatment, and can be made at desired sizes and shapes that satisfy different experimental needs. In particular, an easy, inexpensive, and reproducible method to prepare self-assembled monolayers (SAMs) on CD-R gold substrates after removing the protective polymer films with concentrated nitric acid was described.

Oct 1, 2003

By Rees J. Llewellyn

High chromium white irons can be formulated to provide required combinations of abrasion and erosion wear resistance, toughness and capability to withstand corrosion attack. As a consequence, they are used widely in casting form throughout the mining/mineral processing industry, particularly as components for slurry pumps and also as mill and crusher liners, laminated wear plates in chutes and hoppers and in valves, nozzles and cyclones. Traditional cast chromium molybdenum and high chromium white irons for wear applications are covered in ASTM A532 Classes 11 and 111 and are also available as comparable proprietary alloys. They rely on heat-treated, hypoeutectic microstructures containing a high volume fraction of very hard eutectic/secondary metal carbides and martensite to provide extremely high wear resistance. The ability to increase the carbide volume fraction and hence achieve higher wear resistance, has been limited because of severe casting difficulties encountered when carbon and chromium contents are raised and hypereutectic alloys with structures also containing coarse acicular primary metal carbides are produced. The limitation has been overcome and cast hypereutectic chromium white iron pump components have established themselves in a wide variety of mineral processing service applications. Comparisons will be made between the microstructures and wear test performance data for the various alloy types and details will be provided of the service performance improvements that have been achieved through the use of hypereutectic chromium white irons.

May 1, 2004

Python Underground Processing Plant Critical Design The use of continuous gravity recovery in combination with a controlled breakage fine crushing and screening system followed by flash flotation has been incorporated into the Python processing plant. This provides miners with a flexible, robust, low cost, low energy pre-concentration process for the recovery of gold and/or heavy minerals. The Python plant incorporates fine crushing utilizing either High Pressure Grinding Rolls or Vertical Shaft Impactors in combination with the InLine Pressure Jig and Flash Flotation to continuously liberate and recover the valuable minerals. The use of these technologies has enabled a narrow, transportable pre-concentration plant to be produced which can easily be installed and operated in underground drifts and tunnels.

Sep 13, 2010

Processing of Hard-to-Treat Copper Ore and Flotation Middlings Using Chemical Treatment

Sep 13, 2010

By Arnold O. Tanner

Tables based on 1985 data, which were not available in time for publication of the "1985 Minerals Yearbook," are included in this chapter; corresponding tables for 1986 are not yet available. Raw nonfuel minerals produced in the United States during 1986 had an estimated value of $23.5 billion, an increase of $0.25 billion over the 1985 value. This is the fourth consecutive year that the value has increased, and except for a de- crease in 1982, the value each year has increased since 1971, or 14 out of 15 years. Industrial minerals growth slowed from a 3% increase in value in 1985 to a 1.5% increase in 1986, reflecting the slow growth in the domestic economy. The value of industrial minerals, more than three times larger than the value of metals, easily offset the less than 0.5% decline in the value of metal mine production. Although the decline was small, this decrease makes 1986 the fourth year in the past 6 years in which a drop in the value of metal mining production occurred in the United States. U.S. production continued to lag behind the growing world production. Overall, the estimated raw nonfuel mineral production rose 1% over that of 1985. Domestic mine production of ferrous metals declined as follows, in decreasing order of production: nickel, iron ore, tungsten, and molybdenum. All remaining domestic primary nickel and tungsten mines had closed down by yearend. Nonferrous metals that similarly declined included titanium, rare-earth metals, lead, silver, zinc, and magnesium. For the second consecutive year, aluminum, produced predominantly from imported bauxite, declined in production, while imports reached record-high levels. Somewhat modest gains were made in beryllium and copper. As has been the case for a number of years, gold was a bright spot in the domestic and internation-al metal mining industry. Gold production was spurred on by the increasing usage and development of heapleaching techniques that make lower grade ores, which were previously uneconomical, profitable. Additionally, various mining companies, the U.S. Mint, individual States, and a number of foreign countries began production of gold bullion and commemorative coins. Gold output in the United States increased from 2.43 million troy ounces (revised) in 1985 to about 3.73 million troy ounces in 1986, a dramatic 54% rise.

Jan 1, 1988