Search Documents

By Agnes Y. Lee

he U.S. Bureau of Mines developed a method to treat lead-contaminated soil and ebonite battery casing wastes to produce a nonhazardous material. The cleanup procedure involves wet screening to separate a minus 18-mesh soil fraction; removal of metal1ic lead, rocks, wood, etc. ; carbonation to change lead sulfate to acid-soluble lead carbonate; size reduction; acid leaching; and rinsing. The casing wastes undergo size reduction and washing to remove the lead sulfate sludge before carbonation. Similarly, the minus 18-mesh soil is carbonated, then acid leached and rinsed. In leaching, fluosilicic acid (H SiF,) and hydrogen peroxide (H20,) are used to dissolve lead compounds. An electrowinning method is employed to strip lead from the lead-rich leachate. The acid content in the leachate is replenished with fresh H,SiF, acid prior to recycling. Treated casing wastes and soils pass the Toxicity Characteristic Leaching Procedure (TCLP) test and can be reclassified as nonhazardous materia1s. Based on this process, a conceptual pilot plant has been designed which will be demonstrated on wastes from two Superfund sites.

Jan 1, 1993

By John E. Hamak

The identified helium resources of the United States were estimated by the U.S. Bureau of Mines at 617 Bcf, as of December 31, 1992. This includes 285 Bef of demonstrated reserves, 85 Bcf of demonstrated marginal reserves, and 37 Bcf of demonstrated sub-economic resources. The identified resources also include 166 Bcf of helium in inferred reserves and inferred marginal reserves and 44 Bcf in inferred sub-economic resources. The identified helium resources contained on Federal lands are approximately 172 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. Undiscovered helium resources in the United States are estimated at a most likely volume of 104 Bef, with a maximum volume of 249 Bcf and a minimum volume of 41 Bef. Also reported are 51 Bcf of helium in nonconventional and low-helium-content natural gases. Extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1992 was 3.3 Bcf. Some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1995

By Diana K. Schimmelpfennig

Assessment of revegetation success on mined lands is a difficult, time consuming task and has been the subject of a number of controversies. Present regulations require that both plant cover and aboveground plant biomass be measured for use in making that assessment. Of these two variables, biomass is the most time consuming to measure and requires destructive sampling, a most undesirable requirement on fragile, recently revegetated areas. On the other hand, plant cover can be estimated using the point-frame method which is relatively nondestructive. In addition, vegetation can be sampled more uniformly with the point frame and in less time if species composition measures are to be made. A study was done to evaluate the predictability of aboveground biomass production on revegetated mined sites and adjacent native prairies using plant cover estimates made with the point frame method. The predictability of biomass production by cover estimates bears on the need for both measurements in assessing revegetation success. In general, a positive, statistically, significant correlation was demonstrated between plant cover (estimated by the point frame) and aboveground biomass (estimated by the harvest method) regardless of community type (mined or native), species composition, diversity or level of biomass production. However, the latter did have their effects on the relationship and must be accounted for in any predictive equations (that is to say, the predictive equations must be considered site-specific). Considering the relationship observed between the two parameters, cover estimation may be a sufficient indicator of revegetation success, especially where time and minimization of disturbance are critical.

Jan 1, 1982

By M. C. Irani

This Bureau of Mines survey of methane emissions indicates that total daily emissions have declined from 227 MM ft3 in 1971 to 214.7 MM ft3 in 1973. The highest average daily emissions in million cubic feet per day observed in U.S. bituminous coal mines were, in decreasing order, Monongalia County, W. Va., 40.7; Marion County, W. Va., 23.1; Buchanan County, Va., 22.1; Washington County, Pa. , 12.4; Greene County, Pa. , 11.7; McDowell County, W. Va. , 11.4; Cambria County, Pa., 9.8; Jefferson County, Ala., 9.5; Wyoming County, W. Va., 6.0; Marshall County, W. Va., 4.8; and Indiana County, Pa., 4.8.

Jan 1, 1974

By M. Vallée, J. -P. Charette, D. P. Gold

"The Oka Carbonatite and Alkaline Complex is a Lower Cretaceous intrusive body of the Monteregian petrographic province. Carbonate rocks of various types, and associated alkaline rocks of the ijolite and okaite suites, are distributed in a double ring-dyke structure 4 Yi miles long by 1 1/2 miles across. Alnoite and alrioite breccia pipes intrude all rocks of the Complex and indicate, from inclusions, that a cover of Palaeozoic rocks existed at the time of emplacement.The results of radiometric, magnetic and gravity surveys of the Complex are compiled and discussed both with respect to the regional pattern and, locally, the bed-rock geology. The Complex is characterized by high-intensity anomalies.Exploration activities started during 1953, and mining operations began in 1961 on the property of St. Lawrence Columbium and Metals Corporation, at one time the world's largest producer of niobium concentrates. Because of the boudinaged and fractured nature of many of the rocks and the variability in grade of the ore minerals, the role of the mining geologist is both demanding and exacting. Rock types are varied and their mutual relation-ships ambiguous, the minerals are rare and complex, and close geological control of the ore is needed in the mine and in the mill. Closely spaced diamond drill holes are needed for mining control, and the ore-waste contact is defined mainly by assay results.In the exploration for 'carbonatites' in Eastern Canada, aeromagnetic surveys are judged to be the best exploration tool, followed in decreasing order by the search for circular structures on aerial photographs, regional gravity surveys and radiometric surveys."

Jan 1, 1967

By H. J. Ramey, I. S. Bousaid

Experimental results on the oxidation reaction kinetics in the forward combustion oil recovery process are presented. A total of 48 runs were made wherein a stationary thin layer of coked, unconsoli-dated sand was burned isothermally in a combustion cell. Individual runs were made at various temperature levels to permit determination of the effect of temperature upon the reaction. An expression was obtained for the burning rate of carbon as a function of carbon concentration, combustion temperature and oxygen partial pressure. The carbon burning rate for two types of crude oil indicated a first order reaction with respect to both carbon concentration and oxygen partial pressure. The effect of combustion temperature on the reaction rate constant matched the Arrhenius equation. The activation energy was similar for the two crude oils examined. The activation energy decreased for a porous media containing clay. The rate of oxidation of crude oil at reservoir temperature was found to be significant. Other significant findings included information on hydrogen-carbon content of fuel residues, fuel reactivity and the products of combustion. INTRODUCTION The production of crude oil by underground combustion has been studied in the laboratory by many investigators.1-5 Results of laboratory and field experiments have been reported in the literature describing the forward combustion process. But as yet, no qualitative or quantitative study of the kinetics of fuel combustion involved in this process has been reported. The fuel concentration and the rate at which fuel is burned at the front are important factors governing the air requirement in a forward combustion operation. Although the fuel is essentially unrecoverable crude, the air required to burn the fuel is an important economic factor in this process. Because fuel is burned, the heat transport associated with forward combustion is a key and unique feature of this new oil recovery method. Many investiga-tors5-9 have presented information on the heat transmission and fluid mechanics involved in forward combustion. Berry and Parrish10 demonstrated the utility of considering reaction kinetics in reverse burning. From differential thermal analysis, Tadema11 presented a qualitative discussion of the nature of reactions between oil and oxygen in combustion oil recovery. Although little quantitative work has been done on the reaction kinetics involved in forward combustion oil recovery, an extensive literature does exist on combustion of carbons and oils, and carbonaceous residues from cracking catalyst pellets. Dart, et al., 12 studied the combustion rate for oxidation of carbonaceous residues on clay catalyst pellets, and found the reaction to be second-order with respect to carbon concentration, and first-order with respect to oxygen partial pressure for carbon concentrations less than 2 weight percent of the catalyst weight. The reaction appeared to be first-order with respect to carbon concentration for concentrations greater than 2 percent. Metcalfe13 noted that other workers had found that aging of the fuel during the combustion process was responsible for changing coke properties, and it accounted for the apparent second-order carbon concentration effect found by Dart, et al. It appears that burning of residues from cracking pellets is first-order with respect to both carbon concentration and oxygen partial pressure. Dart, et al., also observed that hydrogen in the hydrocarbon residue appeared to react faster than the carbon. Lewis, et al.,14 studied oxidation of charcoal, coke and graphite in a fluidized bed. Gas velocities were high enough to partially lift and circulate the carbon particles. Their results indicated first-order reaction dependency with respect to both carbon concentration and oxygen partial pressure. One

Jan 1, 1969

By E. Ghali

For engineering applications, magnesium is usually alloyed with one or more elements which include aluminium, manganese, rare earth metals, lithium, zinc, and zirconium. Under normal environmental conditions, the corrosion resistance of magnesium alloys is comparable or better than that of mild steel. The oxide film thickness on pure magnesium after exposure for only ?10 seconds at ambient temperature is 2.2 ± 0.3 nm. Exposure to humid air or to water leads to the formation of a thick hydrated amorphous film that has an oxidation rate less than 0.01 pm/ y. E-pH diagram and high temperature corrosion are discussed. The pH values between 8.5 and 11.5 correspond to a relatively protective oxide or hydroxide film that is more stable at higher pH. Structural applications of magnesium alloys are limited by creep strength rather than by oxidation. Active and active-passive behaviours of magnesium alloys are discussed. The pilling Bedworth Ratio values of oxide and hydroxide are 0.79 and 1.77 respectively and so the formation of Mg(OH)2 inside the oxide film could lead to the development of cracks. Microbiologically influenced corrosion and rational biodegradation of magnesium alloys are discussed because of their interest for medical care.

Jan 1, 2006

By Charles B. Kenahan

The effects of ultrasonic radiation on the electrodeposition of copper-zinc, copper-cadmium, and copper-tin alloys from cyanide baths were investigated by the Bureau of Mines at frequencies of 18.5 and 38 kilocycles per second, and at acoustic intensities up to 0.5 watt per cm3. Significant changes occurred in the composition of the deposited alloys; some of these deposits were brighter, harder, more adherent, or of finer grain size than nonirradiated deposits. The irradiated deposits were also smoother and less porous, and they afforded better corrosion protection for the substrate metal in sodium chloride solution. The limiting current densities of the cyanide baths were increased by the application of ultrasonics. Anode and cathode current efficiencies also were increased, and cell voltages were lowered; the relationship of these effects to current density is discussed. Electrode potential measurements showed significant depolarization effects at both electrodes during ultrasonic irradiation. The resulting decrease in cell voltage was due chiefly to depolarization at the anode, and the anode became less passive.

Jan 1, 1967

By Margaret R. Lickes

Mercury was produced originally at the Idaho Almaden mine from 1939 to 1942. When the ;.nine was shut down, more than 100,000 tons of ore, containing from 2.5 to 3 pounds of mercury per ton, was known to be adjacent to old workings but had been considered too low grade for commercial operation. Later, detailed, systematic exploration by Rare Metals Corporation of America increased and delimited enough minable reserves for further operation to be foreseen for several years. The average grade of the ore is estimated at slightly more than 3.5 pounds of mercury per ton. Open-pit mining and installation of the largest rotary kiln in the United States furnacing mercury ore have made possible profitable exploitation of these reserves (fig. 1). The bulk of the exploration was by percussion drilling, although some diamond drilling was done to check the results. When enough reserves were indicated to assure a successful operation, stripping and plant construction were started simultaneously. Figure 2 is a general view of the plant. The ore bodies, although irregular in size, shape, and grade and covered by essentially barren cap rock, are amenable to low-cost, trackless, open-pit mining. Development consists of stripping the overburden and removing, barren cap rock. Ore is being mined at approximately [5],000 tons per month and treated in a 175-ton-per-day furnacing plant.

Jan 1, 1957

The panic bars (and associated linkage's and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on Self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and soma commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in 'Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By J. E. Fraley

This report describes the preliminary results of a Bureau program to develop and test an inexpensive grout for full-column support of roof bolts. Various inorganic grouts were tested in both cartridge and slurry form. Tests were also performed on methods of water packaging and on the effect of fillers on the grout strength. Results showed that some grouts had poor early strength and exceptional mid-to long-term strength. Laboratory tests have shown that rapid-setting inorganic grout could be an economical replacement for resin bolts if the short-term strength could be increased. Further development to improve its early strength would need to be tested in the laboratory and underground to prove its potential for the mining industry.

Jan 1, 1987

By Lindsay D. Norman

Four chloride and seven fixed-nitrogen processes for recovering manganese from domestic resources are described. The chloride processes are divided into two classes (leaching and chloridization) depending upon the major operation responsible for converting the manganese minerals to the chloride from which manganese oxide products are obtained. The fixed nitrogen processes, all of which yield high-grade manganese oxide products, are essentially either leaching or roasting processes. The 11 processes include HC1 leach, HC1 chloridization, HC1 chloride volatilization, CaC12 chloride volatilization, NO2 leach, HNO3-NO2 leach, NH3-CO2-H2O system leach, (NH4)2SO4 leach, (NH4)2SO4 roast, and ammonium salt roast.

Jan 1, 1963

By J. W. Paul

This report is the second of a series of papers on coal-mining methods and costs which are being prepared by the U. S. Bureau of Mines for the purpose of placing before those interested in the industry a knowledge of the mining methods employed in this particular mine, and cost data on the several operations pertaining to removing the coal from the face into the railroad cars at the tipple with economy and safety. The methods employed are influenced by the natural local conditions, with respect to the thickness of overburden, frequency of local "wants," and the means employed for roof support, and its control

Jan 1, 1929

By I Zulkarnain, H Permana, R A. Binns

Through an ambitious but relatively low-cost program of marine fieldwork, laboratory investigations and technology-transfer and training activities, three Indonesia-Australia-led marine expeditions were undertaken aboard KR Baruna Jaya VIII between 2001 and 2003. These IASSHA (Indonesia-Australia Survey for Submarine Hydrothermal Activity) cruises have sought to discover and investigate a variety of potential ore forming hydrothermal systems in a range of tectonic settings. All cruises have been successful, both scientifically and from the point of view of training, creation of capabilities and capacity building for such research in Indonesia. Over 60 scientists and technicians from Indonesian and Australian institutions and agencies have been involved. Three new sites and a possible fourth site of hydrothermal activity were discovered in the Sangihe arc in northern Sulawesi. Surveys in the Tomini basin tested a hypothesis based on previous data which suggested this might be an isolated anoxic, brine-filled basin over 2000 m deep where igneous heat sources existed to generate hydrothermal mineralisation. The bay, however, was found to be open to adjacent deep ocean circulation, and there was no evidence of massive base metal sulfides. Subdued evidence of hydrothermal activity was found in the Sunda Strait associated with the famous Krakatau volcano and the extension of the seismically active Semangko Fault. The BANDAMIN program (Indonesia-Germany) covered a portion of the Banda arc in eastern Indonesia, and also found evidence of recent hydrothermal activity and epithermal sulfide mineralisation.

Jan 1, 2004

By Jos. R. Guiteras

This is one of a series of information circulars describing mining and milling methods being published by the Bureau of Mines. The Summitville Consolidated Mines, Inc., is the only company now active at Summitville. Since the holdings of the company include those of most of the former producers of the camp, the paper virtually becomes a description of the Summitville district. The field data were collected from August 23 to 28, 1937. ACKNOWLEDGMENTS The writer gratefully acknowledges his indebtedness to H. F. Detrick, president, and Edward Thornton, general manager of the company for their cooperation in making this paper possible. Most of the information on underground operations was given by Roy Jellison, mine superintendent; the metallurgical data were supplied by Art Carl son, metallurgist, and W. L. Anderson, mill superintendent; much general and technical information was supplied by J. H. Hannan, engineer.

Jan 1, 1938

A series of petrological studies were carried out on the characteristics of alteration and mineralisation in mainly structural-controlled (Deep Star, Meikle, Deep Post) and predominantly lithological-controlled (Post-Betze-Screamer and West Leeville) gold deposits in the northern district of the Carlin trend, Nevada. Alteration and mineralisation in these deposits are hosted in a sequence of calcareous clastic units of the Devonian Popovich Formation, into which have been emplaced a number of Jurassic intrusions, and syn- to post-mineral Eocene dikes. Four hydrothermal events have been recognised in these deposits: an initial Devonian base metal system and early diagenesis; a Mississippian stage of alteration in conjunction with burial metamorphism; contact and hydrothermal alteration and base metal-gold mineralisation associated with the emplacement of the Jurassic intrusions; and a Carlin-style gold system related to Eocene magmatism.

Jan 1, 2004

By W. C. Holliman

This report on the characteristics of commercial aviation gasolines is one of a series of such reports. It presents compilations of' inspection data furnished on their products by 15 manufacturers of commercial grades of aviation gasoline and special data obtained in Bureau of Mines laboratories on 68 samples of these gasolines. Data are presented for 18 samples of grade 80, 20 of grade 91/98, 21 of grade100/130, and 9 of grade 115/145 aviation fuels. The gasolines are designated January 1948 production, although some of the samples actually were produced at a later date.

Jan 1, 1948

By Lowell L. Patten

The Federal Bureau of Mines participated with the National Aeronautics and Space Administration and Martin Marietta Aerospace in developing, building, and testing a portable X-ray fluorescence spectrometer for use as an analyzer in mineral-resource investigative work. The prototype battery-powered spectrometer, measuring I1 by 12 by 5 inches and weighing only about 15 pounds, was designed specifically for field use. The spectrometer has two gas-proportional counters and two radioactive sources, 109Cd and 55Fe. Preliminary field and laboratory tests on rock specimens and rock pulps have demonstrated the capability of the spectrometer to detect 33 elements, to date. Characteristics of the system present some limitations, however, and further improvements are recommended.

Jan 1, 1982

By J. J. Hoeppner

Accurate determination of moisture in coals of various ranks has long been a subject of intensive investigation. Excellent reviews of methods developed over many years are given by Brown (9)4/ and, with experimental comparisons, by Goodman, Gomez, and Parry (11). As pointed out in these and other writings, one of the principal difficulties in assigning absolute merit to one or another procedure is the multiplicity of conditions under which water may exist in coal and the difficulties involved in obtaining sharp separation and distinction between these classes. Gauger (10) states: Water recoverable from coal is obtained from the following sources: (1) Decomposition of organic molecules (sometimes called combined water), (2) surface adsorbed water, (3) capillary condensed water, (4) dissolved water, and (5) water of hydration of inorganic constituents of the coal.

Jan 1, 1956

By T. T. Chen

This mineralogical study is based on samples from typical "wet" nickel laterites of humid tropical to sub-tropical regions. An in-situ nickel laterite sample from Goro and a transported laterite sample from Plaine des Lacs, New Caledonia, are predominantly limonitic. Two-thirds of the particles in the Goro sample are <10 um in size; they consist of skeletal goethite and serpentine, as well as minor amounts of talc, gibbsite, chlorite, quartz and clay minerals. The coarser grains are mainly Cr-spinel, serpentine, gibbsite and Mn oxide. Nickel occurs mainly in goethite, serpentine and Mn oxide; cobalt occurs in goethite and Mn oxide. The Plaine des Lacs sample is finer-grained and contains more Al and CO3, but less Mg and Si than the Goro material. The sample contains more kaolinite, chlorite, siderite and feldspar, but less serpentine and gibbsite than the Goro material. Nickel is detected mainly in goethite, serpentine, Fe-Mg silicate and Fe-Mn oxide. The Indonesian ore from Sorowako, as sampled from the reduction kiln feed containing some reverts, is predominantly saprolitic, with apparent particle sizes ranging from <100 um to > 1 cm. The sample of reduction kiln feed is rich in Mg silicates, Mg-Fe silicates and goethite, and exhibits complex alteration textures. The nickel contents vary from particle to particle. Nickel is present mainly in serpentine, olivine, chlorite and amphibole, and in subordinate amounts in goethite and Mn oxide. Cobalt is detected in the Mn oxide. Keywords: Nickel Laterite; Mineralogy; Nickel Carriers; Goro, New Caledonia; Plaine des Lacs, New Caledonia; PT Inco., Sorowaki, Indonesia

Jan 1, 2004