Search Documents

By R. Hogg, T. F. Dumm

"Abstract - With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents, and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and subsieve particle size analysis of the specific gravity fractions, a complete size specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.IntroductionTraditional gravity separation techniques such as jigging, heavy media and water-only cyclones, shaking tables, etc., have been used to remove impurities from coal ranging in size from about 15.cm (6 ln.) to about 150 µm (100 mesh). The coal washabilty or float-and sink technique ls a well-established procedure for determining the optimum extent to which a coal can be cleaned by such physical separation methods. Because of the desire to recover even finer coal fractions by gravity separation techniques, there is a need to extend the coal washabillty analysis into the ultrafine range. The purpose of this paper ls to describe some of the significant factors that influence fine particle specific gravity separation. Washability analyses have been performed on three ultrafine ( <10 µm) coal samples representing three general mining districts in Pennsylvania. Results of these analyses indicate that the washabillty technique can be successfully applied to ultrafine particles when proper care ls taken."

Jan 1, 1988

By Joseph M. Singer

Having established that sodium chloride reduces the incendivity of explosives, the Bureau of Mines studied the effect of sodium nitrate in reducing ignition hazards. Gallery experiments showed that sodium nitrate reduced the incendivity of certain explosives to 8 percent natural gas in air but increased their incendivity to coal dust predispersed in air. Laboratory experiments using hot jets from explosions of stoichiometric mixtures of methane-oxygen-nitrogen showed that both sodium chloride and sodium nitrate reduced the incendivity to methane, to mixtures of coal dust and methane) and to coal dust. The difference between the gallery and laboratory results with respect to coal dust is attributed to temperature-time effects.

Jan 1, 1967

By W. T. Millar

Field reconnaissance and laboratory tests on clay from South Windsor, Hartford County, Conn., indicate that the clay is suitable for lightweight aggregate raw material. Exploration of the deposit supports the conclusion that the reserves of clay are sufficient for economical mining operations to produce lightweight aggregate. Preliminary tests indicated that the clay has a short bloating range. Initial expansion occurred at 2,000° F, and at 2,100° F the clay was slightly overfired and sticky. Rotary kiln tests verified the preliminary data, and these tests showed that the clay would make a good lightweight aggregate if the processing temperature and the kiln feed sizes were closely controlled. Lightweight concrete made from the processed aggregate had properties comparable to those of concrete made from a commercial clay aggregate.

Jan 1, 1964

By M. M. Fine

This report presents the results of laboratory mineral-dressing investigations by the Bureau of Mines of 14 individual or composite character samples from deposits in the Batesville manganese district. It will be noted that some concentrates have met or approached analytical specifications for metallurgical manganese ore although great variations in both physical and chemical composition from once deposit to another make each a new problem. In most cases it is evident that a substantial loss of manganese has occurred in the various slime and tailing products. An important aspect of this work is the research being conducted on manganese-bearing limestones. Recent reconnaissance indicates that this resource constitutes one of the major domestic reserves of manganese. Laboratory study has shown that ferrograde concentrates can be recovered from samples of manganese-bearing limestones from two properties. Research on samples from other areas is still underway.

Jan 1, 1957

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William C. McCulloch

INTRODUCTION The particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 25,400,000 tons of bituminous coal were cleaned by air machines during 1965. They have not found any application for cleaning anthracite. Since the development and introduction of the first successful commercial pneumatic oscillating machine for cleaning bituminous coal in 19 16, by the Sutton, Steele and Steele Co, Dallas, Texas, and the American Coal Cleaning Corporation, formerly of Welch, W. Va., seven other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine. 2. Arms "Concentrator," oscillating table. 3. Hey1 and Patterson oscillating table. 4. "Stump Air-Flow," pulsating air jig. 5. "Super Airflow," pulsating air jig. 6. Ridge air jig. 7. Phillip air jig. While not all coals can be beneficiated by air washing, the air washing of coals that are easy to clean can be readily proved advantageous. Of all the preparation methods, pneumatic cleaning is the most acceptable from the standpoint of delivered Btu cost. This is based on the premise that a percent of moisture is just as detrimental as a percent of ash. The principle of dry concentration has never been determined with scientific accuracy. To the present time the study has been more of an art than a science. It is possible to forecast the results of wet concentration from a study of the washability characteristics of the raw coal but only after applying rule-of-thumb methods of interpretation to the specific gravity and size distribution can it be ascertained that the raw coal is amenable to dry concentration. Air as a separating medium dates back to biblical times as exemplified in the winnowing of chaff from the grain. However, the same application of air to coal serves merely to blow the dust away and size the remaining particles. Pulsating air was the solution to the problem and largely eliminated the necessity for close screen sizing which was required on early separators. Because of the low density of air, a medium of sufficient density has to be built with the material itself. Hence there must be some device to impart to the bed the necessary mobility for proper classification. Also, the

Jan 1, 1968

By William E. Bruce

Percussive drill calibration experiments performed by the Bureau of Mines on two drills are described. The use of a linear velocity transducer to determine piston velocity, blow frequency, and piston stroke length is discussed. Data are presented on the relationships between maximum work rate and feed air pressure. Penetration rates in nine rock types were measured for the same two drills. Physical properties of the nine rock types are presented in tabular and graphical form to show relationships between penetration rates and physical properties. Finally, conclusions are drawn as to the potential use of these data to predict percussive drilling rates.

Jan 1, 1970

By N Collins, A Woodley, A N. Danoucaras, C McCombe, N C. Kunz

Over the past decade, the mining industry has come to recognise the importance of water both to itself and to others. Water accounting is a formalisation of this importance that quantifies and communicates how water is used by individual sites and the industry as a whole. While there are a number of different accounting frameworks that could be used within the industry, the Minerals Council of AustraliaÆs (MCA) water accounting framework (WAF) is an industry-led approach that provides a consistent representation of mine site water interactions regardless of their operational, social or environmental context that allows for valid comparisons between sites and companies.The WAF contains definitions of off-site water sources and destinations and on-site water use, a methodology for applying the definitions, and a set of metrics to measure site performance. The WAF is comprised of two models: the input-output model, which represents the interactions between sites and their surrounding community, and the operational model, which represents on-site water interactions.Members of the MCA have recently adopted the WAFÆs input-output model to report on their external water interactions in their Australian operations, with some adopting it on a global basis. To support this adoption, there is a need for companies to better understand how to implement the WAF in their own operations. Developing a water account is non-trivial, particularly for sites unfamiliar with the WAF or for sites with the need to represent unusual features. This work describes how to build a water account for a given site using the input-output model, with an emphasis on how to represent challenging situations.CITATION:Woodley, A, Danoucaras, A N, McCombe, C, Kunz, N C and Collins, N, 2013. A robust methodological approach for mine site water accounting, in Proceedings Water in Mining 2013 , pp 335-342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By Kenneth M. Earl

In its program of investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the Douglas Deposit in an attempt to find an additional source of supply of copper. The deposit, which was opened in 1878, was worked until 1883 and is reported to have produced between 2 and 3 million pounds of copper. Heap-roasting and smelting and later gravity concentration were employed in ore reduction. Old slag dumps and tailing piles from these operations still remain. In 1917, the American Smelting & Refining Co., purchased the mine, and in June 1918 production was started in a 125-ton mill, using both tables and flotation. The mill was closed December 31, 1918, and soon after the milling plant Was dismantled and removed. The mine has remained idle ever since. The deposit occurs in a mineralized zone that follows the schistosity. The principal metallic minerals are pyrite) chalcopyrite, pyrrhotite) arsenopyrite, sphalerite, magnetite) slight chalcocitel and cuprite. To search for additional ore shoots and to prove the known ore shoot at depth, the Bureau of Mines drilled seven holes, which totaled 2,117.4 feet. No additional ore was developed by this work.

Jan 1, 1950

By D Kentwell

For deposits where a full assay suite of elements/oxides is available and where several variables are critical to the evaluation of the deposit, it is desirable for the estimated block values of all elements/oxides to sum to 100 per cent of the weight per cent. This is difficult to achieve in practice and the estimation methods used need to be designed to minimise bias of the key elements/oxides by ensuring that block estimates are consistent with the individual assays and that the estimated totals are as close as possible to 100 per cent.This paper presents a case study of two domains within a magnetite hematite deposit, one with a high level of drilling classified as Measured and one with a lower density of drilling classified as Indicated. Several estimation methods were tested to evaluate their ability to maintain consistency of the proportions of each element/oxide and sum to 100 per cent. The following methods were evaluated: ordinary kriging, co-kriging, inverse distance and min/max autocorrelation factors (MAF) all as implemented in the Geovariances Isatis software.The comparisons showed that the MAF method produced the most robust estimates in terms of block totals and that grades and tonnages at the reporting cut-off were not significantly different between methods. At an individual block scale all methods produce artefacts that are less than desirable but can only be remedied by additional drilling.CITATION:Kentwell, D, 2015. Comparison of min/max autocorrelation factors, kriging, co-kriging and inverse distance block totals – a magnetite hematite case study, in Proceedings Iron Ore 2015, pp 465–474 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J. W. Griffith, J. L. Stauffer, L. M. Demers, D. C. Kuhn, S. Riliog

"The relative activation of eicosanoid production which results from the exposure of the alveolar macrophage (AM) to mineral dusts is thought to be a key factor in the pathophysiology of occupational lung disease. We compared in vitro basal and silicastimulated production of prostaglandin E2 (PGE2) and thromboxane A2 (TXA2) by AM from normal humans and non-human primates (Macaca nemistrina). In addition, we instilled mineral dusts directly into one lung of the non-human primate and evaluated AM eicosanoid production at two week intervals following dust instillation. Unstimulated AM from humans produce more PGE2 and TXA2 than do AM from M. nemistrina. However, in vitro exposure of AM from both species to silica dust produced a qualitatively similar increase in TXA2 production accompanied by no change in PGE2 production. Sequential analysis of AM eicosanoid production following a single bolus exposure to bituminous or anthracite coal dusts, titanium dioxide (Ti()i) dust or crystalline silica showed marked variability among individual non-human primates in qualitative and quantitative aspects of dust-induced eicosanoid production. However, the rank order of potency of the different dusts (silica> anthracite> bituminous) correlated with epidemiological evidence relating the type of dust mined to the incidence of pneumoconiosis. These studies suggest that the non-human primate may serve as a model for the study of both the role of eicosanoids in the etiology of dust-induced occupational lung disease and the biochemical basis for individual variability in the response of lung cells to mineral dust exposure. IntroductionOccupational inhalation of mineral dust can lead to chronic debilitating lung disease ( 1,2). One of the key components of the disease process is thought to be the interaction of mineral dust with the alveolar macrophage (AM) and the subsequent release by the AM of inflammatory and fibrotic substances (3,4). Chronic inhalation of mineral dust, depending on the type and amount of dust, may then produce a situation in which ongoing inflammation, accompanied by the destruction of functional lung tissue by products of activated AM and polymorphonuclear neutrophils, stimulates the production of nonfunctional matrix by lung fibroblasts.The AM produces several oxygenated derivatives of arachidonic acid (AA) which may play important roles in dust-induced lung pathophysiology (5,6). In previous studies in the rat, we found that prostaglandin E2 (PGE2). thromboxane A2 (TXA2) and leukotriene 84 (L TB4) were the major AA metabolites produced by AM (7). PGE2 is associated with pro-inflammatory activity (8) as well as anti-fibrotic activity since it downregulates interleukin -1 (IL-1) and tumor necrosis factor (TNF) release by AM (9-11). TXA2 is known to stimulate platelet activity, cause bronchial and vascular smooth muscle contraction (12) and to possess chemotactic activity (13). LTB4 is chemotactic for neutrophils and monocytes (14) and has been suggested as an additional regulatory factor in the release of TNF by AM exposed to silica dust ( 15)."

Nov 1, 1995

By Milton Orchin

There has been a good deal of speculation as to the function of a vehicle in the coal hydrogenation process. One of the most fruitful theories has been the suggestion that a vehicle such as tetralin functions by supplying hydrogen to the coal, and that the high-pressure hydrogen present in the system serves to regenerate the tetralin. In order to obtain experimental evidence bearing on this theory, a series of experiments was planned in which varying quantities of tetralin were used with coal in the presence of high-pressure hydrogen. This paper reports the results of these experiments.

Jan 1, 1949

By M. Sahoo, P. Burke, Y. Fasoyinu, J. P. Thomson

The effects of grain refinement, mold temperature and chemical composition on the hot tearing resistance of aluminum alloys 535.0 and 206.0 has been studied by pouring constrained rod castings in metal molds. In addition, two prototype components that could be used in automotive applications were also poured from both alloys by gravity tilt-pour and low pressure permanent mold casting processes. This paper summarizes the results and issues encountered during the casting trials. It was shown that grain refinement and mold temperature ::::: 400°C reduced, and sometimes eliminated hot tear cracks in both alloys. The two prototype engineering components could be cast successfully from both alloys in metal molds. The metallurgical issues related to molten metal treatment and processing temperatures were well controlled. However, issues related to the control of hot tearing, casting and mold design must be addressed in future studies to guarantee the production of defect free castings.

Jan 1, 2006

By H. R. Batchelder

The Bureau of Mines Gas Synthesis Demonstration Plant at Louisiana, Mo., includes apparatus for the gasification of pulverized coal with oxygen and superheated steam. A pebble heater constructed by the Babcock & Wilcox Co. is used to superheat nominal 5-pound steam for the gasification process, usually to temperatures of 1,600° to 2,300° F. with flow rates of 1,400 to 2,300 pounds per hour. Heaters of this sort have been described. So far as is known, the Babcock & Wilcox Co. is the sole commercial manufacturer of equipment of this type. Units have been built with capacities above 18,000 pounds of steam per hour.

Jan 1, 1951

By J. S. Gomer

The U.S. Bureau of Mines conducted Cu exchange tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the Cu exchange capacity as a function of Cu concentration, pH, and temperature. Using these equations, an analysis was made of the impact each clay could have on overall Cu recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of Cu from in situ leaching solutions.

Jan 1, 2010

By George J. Conroy

Results of a long-term program of electrical parameter measurement in under-ground coal mine working sections, performed by The Pennsylvania State University under U. S. Bureau of Mines sponsorship, are utilized as the basis for an analysis of the electrical energy requirements during operation. A model section is hypothesized, developed from the average or most representative characteristics as determined from tabulations of the measurements. Performance factors of the model section&apos;s machine complement are then analyzed, particularly with regard to the energy required per ton of raw coal cut and delivered from the section. Results are given in kilowatt-hours per ton.

Jan 1, 1977

By José Fernandes De Oliveira Ugarte

El presente texto tiene como objetivo la evaluación del oro nativo y electrum encontrado en su forma libre, diseminado, encapsulado en matrices sulfurosas y sulfatadas que fue empleado en los procesos de flotación y lixiviación. Para ello, se estudiaron 54 muestras que fueron analizadas por difracción de rayos X y clasificadas en tres grupos con 18 muestras cada uno e identificadas de matrices oxidada, sulfatada y sulfurosa. Después de tamizadas fueron colocadas en briquetas de 4 mm de diámetro y analizadas por microscopía electrónica para los estudios estadísticos de los minerales portadores de oro y para los estudios de microscopía óptica.

Nov 1, 2015

By Richard W. Hutchinson, Christopher Osterman

Abstract -The Selebi-Phikwe deposits are hosted by amphibolite to granulite facies gneisses of the Limpopo belt. The sulfide orebodies are generally stratiform and conformable to the foliation of the wallrock gneiss. Sulfide remobilization has occurred during metamorphism and has produced discordant sulfide veins, called piercement structures, which project into the hanging wall and foot­ wall gneisses. These piercement structures are compositionally similar to the stratiform sulfides, consisting mainly of pyrrhotite, pentlandite and chalcopyrite. However, texturally the piercement sulfides are coarse grained and inclusion-free, whereas the stratiform sulfides are fine grained and packed with tectonically produced wallrock inclusions. The piercement structure sulfides and adjacent stratabound sulfides were sampled and analyzed for major base metals and PGE&apos;s for comparative purposes. Most of the piercement structures were enriched in Cu, Ag and Au, whereas they were generally depleted in Ni, Co, Fe and PGE&apos;s. Changing elemental associations were observed from the stratabound sulfides and along the length of the piercement structures. This and the degree of depletion or enrichment of various major and minor elements in the sulfide piercement structures may reflect the relative mobilities of metals under metamorphic conditions. The similarities between sulfide piercement structures and the footwall Cu-POE veins in some Sudbury deposits are reviewed.

Jan 1, 1994

By M. F. Ameur, M. Habak, H. Aouici, M. Kenane

Present study interest by aluminium alloy (Al 7175-T5173) drilled without cooling fluid. The influence of the machining parameters (spindle speed and feed rate) on the holes quality was analyzed. Drilling tools are made of carbide (WC); high speed steel (HSS) and TiN coated carbide (WC-Ti).The Experiment design was reinforced by the application of statistical analysis of variance (ANOVA).The results show that the thrust force is influenced principally by the spindle speed and feed rate. Though, both feed rate and tool materials have statistical significance on the surface roughness. In addition, the objective of correlations between spindle speed and feed rate with the evolution of the machining parameters was established. These correlations were obtained by quadratic regression using the response surface methodology. Finally, useful to select optimum values of drilling parameters, that would minimize thrust force, torque, cutting temperature and surface roughness.

Jan 1, 2015

By Thomas W. Thompson

The Zebulon manganese deposit has been known for a number of years. It is situated about 3 miles east of Zebulon, Wake County, N. C., on the Avon, Privett property (fig. 1). The deposit outcrops as a vein, or dike averaging-16 to 20 feet in width. Drilling by the Bureau of Mines has shown that this outcrop results from consolidation of a number of small stringers near the surface. The surface width and the Percentage of manganese oxides (resulting from. weathering) diminish with depth. Below 50 to 80 feet, the vein material is mainly quartz and spessartite garnet. The deposit was first examined by W. T. Benson, a Bureau of Mines engineer, in 1941. The Bureau conducted a diamond-drilling exploratory program an the property from November 7, 1944, to January 25, 1945. A. total of 2,508.5 feet was drilled in 14 holes along the strike of the deposit.

Jan 1, 1950